diff mbox

[U-Boot,v1] OMAP3: fix twister board

Message ID 1465888417-25563-1-git-send-email-sbabic@denx.de
State Accepted
Commit f51c8a99e330dbd6a8db5d45a431390a339cfc41
Delegated to: Tom Rini
Headers show

Commit Message

Stefano Babic June 14, 2016, 7:13 a.m. UTC 
twister board was not updated after changing
SPL defines, resulting in a broken board.

Signed-off-by: Stefano Babic <sbabic@denx.de>
---

 include/configs/tam3517-common.h | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

Comments

Tom Rini June 19, 2016, 2:11 p.m. UTC | #1 
On Tue, Jun 14, 2016 at 09:13:37AM +0200, Stefano Babic wrote:

> twister board was not updated after changing
> SPL defines, resulting in a broken board.
> 
> Signed-off-by: Stefano Babic <sbabic@denx.de>

Applied to u-boot/master, thanks!
Tom Rini June 19, 2016, 2:11 p.m. UTC | #2 
On Tue, Jun 14, 2016 at 09:13:37AM +0200, Stefano Babic wrote:

> twister board was not updated after changing
> SPL defines, resulting in a broken board.
> 
> Signed-off-by: Stefano Babic <sbabic@denx.de>

Applied to u-boot/master, thanks!
diff mbox

Patch

diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h
index efdc706..73ff416 100644
--- a/include/configs/tam3517-common.h
+++ b/include/configs/tam3517-common.h
@@ -207,6 +207,8 @@ 
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBDISK_SUPPORT
 #define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_GPIO_SUPPORT
@@ -219,12 +221,26 @@ 
 
 #define CONFIG_SPL_TEXT_BASE		0x40200000 /*CONFIG_SYS_SRAM_START*/
 #define CONFIG_SPL_MAX_SIZE		(54 * 1024)	/* 8 KB for stack */
+#define CONFIG_SPL_STACK		LOW_LEVEL_SRAM_STACK
 
 #define CONFIG_SYS_SPL_MALLOC_START	0x8f000000
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x80000
 #define CONFIG_SPL_BSS_START_ADDR	0x8f080000 /* end of RAM */
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000
 
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300 /* address 0x60000 */
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
+
+/* FAT */
+#define CONFIG_SPL_FS_LOAD_KERNEL_NAME		"uImage"
+#define CONFIG_SPL_FS_LOAD_ARGS_NAME		"args"
+
+/* RAW SD card / eMMC */
+#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR	0x900	/* address 0x120000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR	0x80	/* address 0x10000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS	0x80	/* 64KiB */
+
 /* NAND boot config */
 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT
 #define CONFIG_SYS_NAND_PAGE_COUNT	64