diff --git a/arch/powerpc/cpu/mpc8xx/speed.c b/arch/powerpc/cpu/mpc8xx/speed.c
index 42442b8..513ad7b 100644
--- a/arch/powerpc/cpu/mpc8xx/speed.c
+++ b/arch/powerpc/cpu/mpc8xx/speed.c
@@ -370,8 +370,7 @@ static long init_pll_866 (long clk)
 
 #endif /* CONFIG_8xx_CPUCLK_DEFAULT */
 
-#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M) \
-    && !defined(CONFIG_TQM885D)
+#if defined(CONFIG_TQM8xxL)
 /*
  * Adjust sdram refresh rate to actual CPU clock
  * and set timebase source according to actual CPU clock
diff --git a/arch/powerpc/lib/board.c b/arch/powerpc/lib/board.c
index 300ab12..c973fc2 100644
--- a/arch/powerpc/lib/board.c
+++ b/arch/powerpc/lib/board.c
@@ -251,8 +251,7 @@ static init_fnc_t *init_sequence[] = {
 #endif
 #if !defined(CONFIG_8xx_CPUCLK_DEFAULT)
 	get_clocks,		/* get CPU and bus clocks (etc.) */
-#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M) \
-    && !defined(CONFIG_TQM885D)
+#if defined(CONFIG_TQM8xxL)
 	adjust_sdram_tbs_8xx,
 #endif
 	init_timebase,
diff --git a/board/tqc/tqm8xx/tqm8xx.c b/board/tqc/tqm8xx/tqm8xx.c
index 9ce2a57..aec61f8 100644
--- a/board/tqc/tqm8xx/tqm8xx.c
+++ b/board/tqc/tqm8xx/tqm8xx.c
@@ -118,9 +118,6 @@ int checkboard (void)
 			break;
 		putc (buf[i]);
 	}
-#ifdef CONFIG_VIRTLAB2
-	puts (" (Virtlab2)");
-#endif
 	putc ('\n');
 
 	return (0);
@@ -512,14 +509,6 @@ int misc_init_r (void)
 	immap->im_ioport.iop_padat &= ~0x0001;	/* turn it off */
 # endif
 
-#ifdef CONFIG_NSCU
-	/* wake up ethernet module */
-	immap->im_ioport.iop_pcpar &= ~0x0004;	/* GPIO pin      */
-	immap->im_ioport.iop_pcdir |= 0x0004;	/* output        */
-	immap->im_ioport.iop_pcso &= ~0x0004;	/* for clarity   */
-	immap->im_ioport.iop_pcdat |= 0x0004;	/* enable        */
-#endif /* CONFIG_NSCU */
-
 	return (0);
 }
 #endif	/* CONFIG_MISC_INIT_R */
@@ -680,49 +669,3 @@ void ft_board_setup(void *blob, bd_t *bd)
 	ft_blob_update(blob, bd);
 }
 #endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */
-
-/* ---------------------------------------------------------------------------- */
-/* TK885D specific initializaion						*/
-/* ---------------------------------------------------------------------------- */
-#ifdef CONFIG_TK885D
-#include <miiphy.h>
-int last_stage_init(void)
-{
-	const unsigned char phy[] = {CONFIG_FEC1_PHY, CONFIG_FEC2_PHY};
-	unsigned short reg;
-	int ret, i = 100;
-	char *s;
-
-	mii_init();
-	/* Without this delay 0xff is read from the UART buffer later in
-	 * abortboot() and autoboot is aborted */
-	udelay(10000);
-	while (tstc() && i--)
-		(void)getc();
-
-	/* Check if auto-negotiation is prohibited */
-	s = getenv("phy_auto_nego");
-
-	if (!s || !strcmp(s, "on"))
-		/* Nothing to do - autonegotiation by default */
-		return 0;
-
-	for (i = 0; i < 2; i++) {
-		ret = miiphy_read("FEC", phy[i], MII_BMCR, &reg);
-		if (ret) {
-			printf("Cannot read BMCR on PHY %d\n", phy[i]);
-			return 0;
-		}
-		/* Auto-negotiation off, hard set full duplex, 100Mbps */
-		ret = miiphy_write("FEC", phy[i],
-				   MII_BMCR, (reg | BMCR_SPEED100 |
-					      BMCR_FULLDPLX) & ~BMCR_ANENABLE);
-		if (ret) {
-			printf("Cannot write BMCR on PHY %d\n", phy[i]);
-			return 0;
-		}
-	}
-
-	return 0;
-}
-#endif
diff --git a/boards.cfg b/boards.cfg
index 1ba2081..1b4feb8 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -1002,24 +1002,13 @@ Active  powerpc     mpc8xx         -           LEOX            elpt860
 Active  powerpc     mpc8xx         -           manroland       uc100               uc100                                 -                                                                                                                                 Stefan Roese <sr@denx.de>
 Active  powerpc     mpc8xx         -           tqc             tqm8xx              FPS850L                               -                                                                                                                                 Wolfgang Denk <wd@denx.de>
 Active  powerpc     mpc8xx         -           tqc             tqm8xx              FPS860L                               -                                                                                                                                 Wolfgang Denk <wd@denx.de>
-Active  powerpc     mpc8xx         -           tqc             tqm8xx              NSCU                                  -                                                                                                                                 -
 Active  powerpc     mpc8xx         -           tqc             tqm8xx              SM850                                 -                                                                                                                                 Wolfgang Denk <wd@denx.de>
-Active  powerpc     mpc8xx         -           tqc             tqm8xx              TK885D                                -                                                                                                                                 -
 Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM823L                               -                                                                                                                                 Wolfgang Denk <wd@denx.de>
 Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM823L_LCD                           TQM823L:LCD,NEC_NL6448BC20                                                                                                        Wolfgang Denk <wd@denx.de>
-Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM823M                               -                                                                                                                                 -
 Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM850L                               -                                                                                                                                 Wolfgang Denk <wd@denx.de>
-Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM850M                               -                                                                                                                                 -
 Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM855L                               -                                                                                                                                 Wolfgang Denk <wd@denx.de>
-Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM855M                               -                                                                                                                                 -
 Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM860L                               -                                                                                                                                 Wolfgang Denk <wd@denx.de>
-Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM860M                               -                                                                                                                                 -
-Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM862L                               -                                                                                                                                 -
-Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM862M                               -                                                                                                                                 -
-Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM866M                               -                                                                                                                                 -
-Active  powerpc     mpc8xx         -           tqc             tqm8xx              TQM885D                               -                                                                                                                                 -
 Active  powerpc     mpc8xx         -           tqc             tqm8xx              TTTech                                TQM823L:LCD,SHARP_LQ104V7DS01                                                                                                     Wolfgang Denk <wd@denx.de>
-Active  powerpc     mpc8xx         -           tqc             tqm8xx              virtlab2                              -                                                                                                                                 -
 Active  powerpc     mpc8xx         -           tqc             tqm8xx              wtk                                   TQM823L:LCD,SHARP_LQ065T9DR51U                                                                                                    Wolfgang Denk <wd@denx.de>
 Active  powerpc     ppc4xx         -           -               csb272              csb272                                -                                                                                                                                 Tolunay Orkun <torkun@nextio.com>
 Active  powerpc     ppc4xx         -           -               csb472              csb472                                -                                                                                                                                 Tolunay Orkun <torkun@nextio.com>
diff --git a/common/board_f.c b/common/board_f.c
index bdab38e..c14fa91 100644
--- a/common/board_f.c
+++ b/common/board_f.c
@@ -795,8 +795,7 @@ static init_fnc_t init_sequence_f[] = {
 	/* TODO: can any of this go into arch_cpu_init()? */
 #if defined(CONFIG_PPC) && !defined(CONFIG_8xx_CPUCLK_DEFAULT)
 	get_clocks,		/* get CPU and bus clocks (etc.) */
-#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M) \
-		&& !defined(CONFIG_TQM885D)
+#if defined(CONFIG_TQM8xxL)
 	adjust_sdram_tbs_8xx,
 #endif
 	/* TODO: can we rename this to timer_init()? */
diff --git a/drivers/i2c/soft_i2c.c b/drivers/i2c/soft_i2c.c
index db9b402..5ebccc2 100644
--- a/drivers/i2c/soft_i2c.c
+++ b/drivers/i2c/soft_i2c.c
@@ -29,9 +29,6 @@
 #include <asm/arch/gpio.h>
 #endif
 #endif
-#if defined(CONFIG_MPC852T) || defined(CONFIG_MPC866)
-#include <asm/io.h>
-#endif
 #include <i2c.h>
 
 #if defined(CONFIG_SOFT_I2C_GPIO_SCL)
diff --git a/drivers/pcmcia/mpc8xx_pcmcia.c b/drivers/pcmcia/mpc8xx_pcmcia.c
index af77426..ea88494 100644
--- a/drivers/pcmcia/mpc8xx_pcmcia.c
+++ b/drivers/pcmcia/mpc8xx_pcmcia.c
@@ -58,7 +58,7 @@ static const u_int m8xx_size_to_gray[M8XX_SIZES_NO] =
 
 /* -------------------------------------------------------------------- */
 
-#if	defined(CONFIG_LWMON) || defined(CONFIG_NSCU)
+#if	defined(CONFIG_LWMON)
 #define	CONFIG_SYS_PCMCIA_TIMING	(	PCMCIA_SHT(9)	\
 				|	PCMCIA_SST(3)	\
 				|	PCMCIA_SL(12))
diff --git a/drivers/pcmcia/tqm8xx_pcmcia.c b/drivers/pcmcia/tqm8xx_pcmcia.c
index dda7d37..2f69c1b 100644
--- a/drivers/pcmcia/tqm8xx_pcmcia.c
+++ b/drivers/pcmcia/tqm8xx_pcmcia.c
@@ -22,53 +22,12 @@
 #if	defined(CONFIG_PCMCIA)	\
 	&& (defined(CONFIG_TQM8xxL) || defined(CONFIG_SVM_SC8xx))
 
-#if	defined(CONFIG_VIRTLAB2)
-#define	PCMCIA_BOARD_MSG	"Virtlab2"
-#elif	defined(CONFIG_TQM8xxL)
+#if	defined(CONFIG_TQM8xxL)
 #define	PCMCIA_BOARD_MSG	"TQM8xxL"
 #elif	defined(CONFIG_SVM_SC8xx)
 #define	PCMCIA_BOARD_MSG	"SC8xx"
 #endif
 
-#if	defined(CONFIG_NSCU)
-
-static inline void power_config(int slot) {}
-static inline void power_off(int slot) {}
-static inline void power_on_5_0(int slot) {}
-static inline void power_on_3_3(int slot) {}
-
-#elif	defined(CONFIG_VIRTLAB2)
-
-static inline void power_config(int slot) {}
-
-static inline void power_off(int slot)
-{
-	volatile unsigned __iomem *addr;
-	addr = (volatile unsigned __iomem *)PCMCIA_CTRL;
-
-	out_be32(addr, 0);
-}
-
-static inline void power_on_5_0(int slot)
-{
-	volatile unsigned __iomem *addr;
-	addr = (volatile unsigned __iomem *)PCMCIA_CTRL;
-
-	/* Enable 5V Vccout */
-	out_be32(addr, 2);
-}
-
-static inline void power_on_3_3(int slot)
-{
-	volatile unsigned __iomem *addr;
-	addr = (volatile unsigned __iomem *)PCMCIA_CTRL;
-
-	/* Enable 3.3V Vccout */
-	out_be32(addr, 1);
-}
-
-#else
-
 static inline void power_config(int slot)
 {
 	immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
@@ -100,8 +59,6 @@ static inline void power_on_3_3(int slot)
 	setbits_be16(&immap->im_ioport.iop_pcdir, 0x0002 | 0x0004);
 }
 
-#endif
-
 /*
  * Function to retrieve the PIPR register, used for debuging purposes.
  */
@@ -245,7 +202,6 @@ int pcmcia_hardware_disable(int slot)
 
 int pcmcia_voltage_set(int slot, int vcc, int vpp)
 {
-#ifndef CONFIG_NSCU
 	u_long reg;
 	uint32_t pipr = 0;
 
@@ -298,7 +254,7 @@ done:
 	udelay(500);
 
 	debug("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n", slot+'A');
-#endif	/* CONFIG_NSCU */
+
 	return 0;
 }
 
diff --git a/include/common.h b/include/common.h
index 82c0a5a..e272ef7 100644
--- a/include/common.h
+++ b/include/common.h
@@ -28,14 +28,10 @@ typedef volatile unsigned char	vu_char;
 #endif
 #if defined(CONFIG_8xx)
 #include <asm/8xx_immap.h>
-#if defined(CONFIG_MPC859)	|| defined(CONFIG_MPC859T)	|| \
-    defined(CONFIG_MPC866)	|| \
+#if defined(CONFIG_MPC859T)	|| \
     defined(CONFIG_MPC866P)
 # define CONFIG_MPC866_FAMILY 1
-#elif defined(CONFIG_MPC870) \
-   || defined(CONFIG_MPC875) \
-   || defined(CONFIG_MPC880) \
-   || defined(CONFIG_MPC885)
+#elif defined(CONFIG_MPC875)
 # define CONFIG_MPC885_FAMILY   1
 #endif
 #if   defined(CONFIG_MPC860)	   \
@@ -150,22 +146,11 @@ typedef void (interrupt_handler_t)(void *);
 #include <asm/global_data.h>	/* global data used for startup functions */
 
 /*
- * enable common handling for all TQM8xxL/M boards:
- * - CONFIG_TQM8xxM will be defined for all TQM8xxM boards
- * - CONFIG_TQM8xxL will be defined for all TQM8xxL _and_ TQM8xxM boards
- *                  and for the TQM885D board
+ * enable common handling for all TQM8xxL boards:
+ * - CONFIG_TQM8xxL will be defined for all TQM8xxL boards
  */
-#if defined(CONFIG_TQM823M) || defined(CONFIG_TQM850M) || \
-    defined(CONFIG_TQM855M) || defined(CONFIG_TQM860M) || \
-    defined(CONFIG_TQM862M) || defined(CONFIG_TQM866M)
-# ifndef CONFIG_TQM8xxM
-#  define CONFIG_TQM8xxM
-# endif
-#endif
 #if defined(CONFIG_TQM823L) || defined(CONFIG_TQM850L) || \
-    defined(CONFIG_TQM855L) || defined(CONFIG_TQM860L) || \
-    defined(CONFIG_TQM862L) || defined(CONFIG_TQM8xxM) || \
-    defined(CONFIG_TQM885D)
+    defined(CONFIG_TQM855L) || defined(CONFIG_TQM860L)
 # ifndef CONFIG_TQM8xxL
 #  define CONFIG_TQM8xxL
 # endif
diff --git a/include/commproc.h b/include/commproc.h
index 52ac4ca..c5610bc 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -931,18 +931,15 @@ typedef struct scc_enet {
 #if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
     defined(CONFIG_R360MPI) || \
     defined(CONFIG_RRVISION)|| defined(CONFIG_TQM823L) || \
-    defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \
-    defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D) || \
-    defined(CONFIG_RRVISION)|| defined(CONFIG_VIRTLAB2)
+    defined(CONFIG_TQM850L) || \
+    defined(CONFIG_RRVISION)
 
 /* Bits in parallel I/O port registers that have to be set/cleared
  * to configure the pins for SCC2 use.
  */
 #define	PROFF_ENET	PROFF_SCC2
 #define	CPM_CR_ENET	CPM_CR_CH_SCC2
-#if (!defined(CONFIG_TK885D))	/* TK885D does not use SCC Ethernet */
 #define	SCC_ENET	1
-#endif
 #define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
 #define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
 #define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
@@ -970,10 +967,9 @@ typedef struct scc_enet {
 
 /***  TQM855L/M, TQM860L/M, TQM862L/M, TQM866L/M  *********************/
 
-#if defined(CONFIG_TQM855L) || defined(CONFIG_TQM855M) || \
-    defined(CONFIG_TQM860L) || defined(CONFIG_TQM860M) || \
-    defined(CONFIG_TQM862L) || defined(CONFIG_TQM862M) || \
-    defined(CONFIG_TQM866L) || defined(CONFIG_TQM866M)
+#if defined(CONFIG_TQM855L) || \
+    defined(CONFIG_TQM860L) || \
+    defined(CONFIG_TQM866L)
 
 # ifdef CONFIG_SCC1_ENET	/* use SCC for 10Mbps Ethernet	*/
 
diff --git a/include/configs/NSCU.h b/include/configs/NSCU.h
deleted file mode 100644
index a9c649a..0000000
--- a/include/configs/NSCU.h
+++ /dev/null
@@ -1,463 +0,0 @@
-/*
- * (C) Copyright 2000-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC855		1	/* This is a MPC855 CPU		*/
-#define CONFIG_TQM855M		1	/* ...on a TQM8xxM module	*/
-#define CONFIG_NSCU		1
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define	CONFIG_8xx_CONS_SCC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-
-#define	CONFIG_66MHz		1	/* running at 66 MHz, 1:1 clock	*/
-
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"hostname=NSCU\0"						\
-	"bootfile=${hostname}/uImage\0"					\
-	"kernel_addr=40080000\0"					\
-	"ramdisk_addr=40180000\0"					\
-	"u-boot=${hostname}/u-image.bin\0"				\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"update=prot off 40000000 +${filesize};"			\
-		"era 40000000 +${filesize};"				\
-		"cp.b 200000 40000000 ${filesize};"			\
-		"sete filesize;save\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_MISC_INIT_R	  1
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-#define	CONFIG_ISP1362_USB		/* ISP1362 USB OTG controller	*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_NETCONSOLE
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history
-*/
-#define	CONFIG_SYS_HUSH_PARSER		1	/* use "hush" command parser	*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE+flash_info[0].size }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
-#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef	CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-/* NSCU use both slots, SLOT_A as "primary". */
-#define	CONFIG_PCMCIA_SLOT_A 1
-
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-#define PCMCIA_MEM_WIN_NO	8 /* override default 4 in pcmcia.h */
-#define	PCMCIA_SOCKETS_NO	2 /* we have two sockets */
-#undef	NSCU_OE_INV		/* PCMCIA_GCRX_CXOE was inverted on early boards */
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		2	/* max. 2 IDE buses		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	4	/* max. 2 drives per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-#define CONFIG_SYS_ATA_IDE1_OFFSET	(4 * CONFIG_SYS_PCMCIA_MEM_SIZE) /* starts @ 4th window */
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef	CONFIG_CAN_DRIVER
-#define	CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define	CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-#ifdef	CONFIG_ISP1362_USB
-#define	CONFIG_SYS_ISP1362_BASE	0xD0000000	/* ISP1362 mapped at 0xD0000000 */
-#define CONFIG_SYS_ISP1362_OR_AM	0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR5_ISP1362		(CONFIG_SYS_ISP1362_OR_AM | OR_CSNT_SAM | \
-				 OR_ACS_DIV2       | OR_BI       | OR_SCY_5_CLK)
-#define CONFIG_SYS_BR5_ISP1362		((CONFIG_SYS_ISP1362_BASE & BR_BA_MSK) | \
-				 BR_PS_16          | BR_MS_GPCM | BR_V )
-#endif	/* CONFIG_ISP1362_USB */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA	98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#undef CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/TK885D.h b/include/configs/TK885D.h
deleted file mode 100644
index 5e1c52d..0000000
--- a/include/configs/TK885D.h
+++ /dev/null
@@ -1,490 +0,0 @@
-/*
- * (C) Copyright 2000-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2006
- * Martin Krause, TQ-Systems GmBH, martin.krause@tqs.de
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC885		1	/* This is a MPC885 CPU		*/
-#define CONFIG_TQM885D		1	/* ...on a TQM88D module	*/
-#define CONFIG_TK885D		1	/* ...in a TK885D base board	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define CONFIG_8xx_OSCLK		10000000	/*  10 MHz - PLL input clock	*/
-#define CONFIG_SYS_8xx_CPUCLK_MIN		15000000	/*  15 MHz - CPU minimum clock	*/
-#define CONFIG_SYS_8xx_CPUCLK_MAX		133000000	/* 133 MHz - CPU maximum clock	*/
-#define CONFIG_8xx_CPUCLK_DEFAULT	66000000	/*  66 MHz - CPU default clock	*/
-						/* (it will be used if there is no	*/
-						/* 'cpuclk' variable with valid value)	*/
-
-#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;" \
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"ethprime=FEC\0"						\
-	"ethact=FEC\0"							\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/tk885d/uImage\0"				\
-	"u-boot=/tftpboot/tk885d/u-boot.bin\0"				\
-	"kernel_addr=40080000\0"					\
-	"ramdisk_addr=40180000\0"					\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"update=protect off 40000000 +${filesize};"			\
-		"erase 40000000 +${filesize};"				\
-		"cp.b 200000 40000000 ${filesize};"			\
-		"protect on 40000000 +${filesize}\0"			\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL		0x00000020	/* PB 26 */
-#define PB_SDA		0x00000010	/* PB 27 */
-
-#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else	immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* EEPROM AT24C??	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2		/* two byte address	*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
-
-# define CONFIG_RTC_DS1337 1
-# define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#undef CONFIG_RTC_MPC8xx		/* MPC885 does not support RTC	*/
-
-#define	CONFIG_TIMESTAMP		/* but print image timestmps	*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0100000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0300000	/* 1 ... 3 MB in DRAM	*/
-#define CONFIG_SYS_ALT_MEMTEST				/* alternate, more extensive
-						   memory test.*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/*
- * Enable loopw command.
- */
-#define CONFIG_LOOPW
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_OFFSET		0x40000 /*   Offset   of Environment Sector	*/
-#define CONFIG_ENV_SIZE		0x08000 /* Total Size of Environment		*/
-#define CONFIG_ENV_SECT_SIZE	0x40000 /* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size	  of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing: Default value of OR0 after reset
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
-				 OR_SCY_6_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define SDRAM_MAX_SIZE		(256 << 20)	/* max 256 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*
- * 4096	Rows from SDRAM example configuration
- * 1000	factor s -> ms
- * 64	PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4	Number of refresh cycles per period
- * 64	Refresh cycle in ms per number of rows
- */
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 64 * 1000) / (4 * 64))
-
-/*
- * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad)
- *
- *                        CPUclock(MHz) * 31.2
- * CONFIG_SYS_MAMR_PTA = -----------------------------------     with DFBRG = 0
- *                2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16
- *
- * CPU clock =  15 MHz:  CONFIG_SYS_MAMR_PTA =  29   ->  4 * 7.73 us
- * CPU clock =  50 MHz:  CONFIG_SYS_MAMR_PTA =  97   ->  4 * 7.76 us
- * CPU clock =  66 MHz:  CONFIG_SYS_MAMR_PTA = 128   ->  4 * 7.75 us
- * CPU clock = 133 MHz:  CONFIG_SYS_MAMR_PTA = 255   ->  4 * 7.67 us
- *
- * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will
- * be met also in the default configuration, i.e. if environment variable
- * 'cpuclk' is not set.
- */
-#define CONFIG_SYS_MAMR_PTA		128
-
-/*
- * Memory Periodic Timer Prescaler Register (MPTPR) values.
- */
-/* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16
-/* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 10 column SDRAM */
-#define CONFIG_SYS_MAMR_10COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9  |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-/*
- * Network configuration
- */
-#define CONFIG_FEC_ENET			/* enable ethernet on FEC */
-#define CONFIG_ETHER_ON_FEC1		/* ... for FEC1 */
-#define CONFIG_ETHER_ON_FEC2		/* ... for FEC2 */
-
-#define CONFIG_LAST_STAGE_INIT		1 /* Have to configure PHYs for Linux */
-
-/* CONFIG_SYS_DISCOVER_PHY only works with FEC if only one interface is enabled */
-#if (!defined(CONFIG_ETHER_ON_FEC1) || !defined(CONFIG_ETHER_ON_FEC2))
-#define CONFIG_SYS_DISCOVER_PHY
-#endif
-
-#ifndef CONFIG_SYS_DISCOVER_PHY
-/* PHY addresses - hard wired in hardware */
-#define CONFIG_FEC1_PHY	1
-#define CONFIG_FEC2_PHY	2
-#endif
-
-#define CONFIG_MII_INIT	1
-
-#define CONFIG_NET_RETRY_COUNT	3
-#define CONFIG_ETHPRIME		"FEC"
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/TQM823M.h b/include/configs/TQM823M.h
deleted file mode 100644
index 4fd070f..0000000
--- a/include/configs/TQM823M.h
+++ /dev/null
@@ -1,464 +0,0 @@
-/*
- * (C) Copyright 2000-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
-#define CONFIG_TQM823M		1	/* ...on a TQM8xxM module	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#ifdef	CONFIG_LCD			/* with LCD controller ?	*/
-#define CONFIG_MPC8XX_LCD
-/* #define CONFIG_NEC_NL6448BC20 1 / * use NEC NL6448BC20 display	*/
-#endif
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define	CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"hostname=TQM823M\0"						\
-	"bootfile=TQM823M/uImage\0"					\
-	"fdt_addr=40080000\0"						\
-	"kernel_addr=400A0000\0"					\
-	"ramdisk_addr=40280000\0"					\
-	"u-boot=TQM823M/u-image.bin\0"					\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"update=prot off 40000000 +${filesize};"			\
-		"era 40000000 +${filesize};"				\
-		"cp.b 200000 40000000 ${filesize};"			\
-		"sete filesize;save\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#ifdef CONFIG_LCD
-# undef	 CONFIG_STATUS_LED		/* disturbs display		*/
-#else
-# define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-#endif	/* CONFIG_LCD */
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_NETCONSOLE
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
-#define	CONFIG_ENV_SIZE		0x08000	/* Total Size of Environment		*/
-#define	CONFIG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R		/* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
-
-#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
-						"128k(dtb),"		\
-						"1920k(kernel),"	\
-						"5632(rootfs),"		\
-						"4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef	CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef	CONFIG_CAN_DRIVER
-#define	CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define	CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA	98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/TQM850M.h b/include/configs/TQM850M.h
deleted file mode 100644
index 659c9ad..0000000
--- a/include/configs/TQM850M.h
+++ /dev/null
@@ -1,454 +0,0 @@
-/*
- * (C) Copyright 2000-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC850		1	/* This is a MPC850 CPU		*/
-#define CONFIG_TQM850M		1	/* ...on a TQM8xxM module	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define	CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"hostname=TQM850M\0"						\
-	"bootfile=TQM850M/uImage\0"					\
-	"fdt_addr=40080000\0"						\
-	"kernel_addr=400A0000\0"					\
-	"ramdisk_addr=40280000\0"					\
-	"u-boot=TQM850M/u-image.bin\0"					\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"update=prot off 40000000 +${filesize};"			\
-		"era 40000000 +${filesize};"				\
-		"cp.b 200000 40000000 ${filesize};"			\
-		"sete filesize;save\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_NETCONSOLE
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
-#define	CONFIG_ENV_SIZE		0x08000	/* Total Size of Environment		*/
-#define	CONFIG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R		/* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
-
-#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
-						"128k(dtb),"		\
-						"1920k(kernel),"	\
-						"5632(rootfs),"		\
-						"4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef	CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef	CONFIG_CAN_DRIVER
-#define	CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define	CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA	98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/TQM855M.h b/include/configs/TQM855M.h
deleted file mode 100644
index 44d456e..0000000
--- a/include/configs/TQM855M.h
+++ /dev/null
@@ -1,491 +0,0 @@
-/*
- * (C) Copyright 2000-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC855		1	/* This is a MPC855 CPU		*/
-#define CONFIG_TQM855M		1	/* ...on a TQM8xxM module	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define	CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"hostname=TQM855M\0"						\
-	"bootfile=TQM855M/uImage\0"					\
-	"fdt_addr=40080000\0"						\
-	"kernel_addr=400A0000\0"					\
-	"ramdisk_addr=40280000\0"					\
-	"u-boot=TQM855M/u-image.bin\0"					\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"update=prot off 40000000 +${filesize};"			\
-		"era 40000000 +${filesize};"				\
-		"cp.b 200000 40000000 ${filesize};"			\
-		"sete filesize;save\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL		0x00000020	/* PB 26 */
-#define PB_SDA		0x00000010	/* PB 27 */
-
-#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* EEPROM AT24C64	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2		/* two byte address	*/
-#if 0
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* takes up to 10 msec	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5
-#endif
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_NETCONSOLE
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
-#define	CONFIG_ENV_SIZE		0x08000	/* Total Size of Environment		*/
-#define	CONFIG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R		/* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
-
-#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
-						"128k(dtb),"		\
-						"1920k(kernel),"	\
-						"5632(rootfs),"		\
-						"4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef	CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef	CONFIG_CAN_DRIVER
-#define	CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define	CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA	98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME		"SCC"
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/TQM860M.h b/include/configs/TQM860M.h
deleted file mode 100644
index 8109379..0000000
--- a/include/configs/TQM860M.h
+++ /dev/null
@@ -1,464 +0,0 @@
-/*
- * (C) Copyright 2000-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860		1	/* This is a MPC860 CPU		*/
-#define CONFIG_TQM860M		1	/* ...on a TQM8xxM module	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define	CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"hostname=TQM860M\0"						\
-	"bootfile=TQM860M/uImage\0"					\
-	"fdt_addr=400C0000\0"						\
-	"kernel_addr=40100000\0"					\
-	"ramdisk_addr=40280000\0"					\
-	"u-boot=TQM860M/u-image.bin\0"					\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"update=prot off 40000000 +${filesize};"			\
-		"era 40000000 +${filesize};"				\
-		"cp.b 200000 40000000 ${filesize};"			\
-		"sete filesize;save\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_NETCONSOLE
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
-#define	CONFIG_ENV_SIZE		0x08000	/* Total Size of Environment Sector	*/
-#define	CONFIG_ENV_SECT_SIZE	0x40000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R		/* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
-
-#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
-						"128k(dtb),"		\
-						"1920k(kernel),"	\
-						"5632(rootfs),"		\
-						"4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef	CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define	SDRAM_MAX_SIZE		0x08000000	/* max 128 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef	CONFIG_CAN_DRIVER
-#define	CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define	CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA	98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 10 column SDRAM */
-#define CONFIG_SYS_MAMR_10COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9  |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME		"SCC"
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/TQM862L.h b/include/configs/TQM862L.h
deleted file mode 100644
index da4af93..0000000
--- a/include/configs/TQM862L.h
+++ /dev/null
@@ -1,464 +0,0 @@
-/*
- * (C) Copyright 2000-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860		1
-#define CONFIG_MPC860T		1
-#define CONFIG_MPC862		1
-
-#define CONFIG_TQM862L		1	/* ...on a TQM8xxL module	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define	CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"hostname=TQM862L\0"						\
-	"bootfile=TQM862L/uImage\0"					\
-	"fdt_addr=40040000\0"						\
-	"kernel_addr=40060000\0"					\
-	"ramdisk_addr=40200000\0"					\
-	"u-boot=TQM862L/u-image.bin\0"					\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"update=prot off 40000000 +${filesize};"			\
-		"era 40000000 +${filesize};"				\
-		"cp.b 200000 40000000 ${filesize};"			\
-		"sete filesize;save\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_NETCONSOLE
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE+flash_info[0].size }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
-#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R		/* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT		"nor0=TQM8xxL-0"
-
-#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxL-0:256k(u-boot),"	\
-						"128k(dtb),"		\
-						"1664k(kernel),"	\
-						"2m(rootfs),"		\
-						"4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef	CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #1	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef	CONFIG_CAN_DRIVER
-#define	CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define	CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- *  50 MHz =>  50.000.000 / Divider =  98
- *  66 Mhz =>  66.000.000 / Divider = 129
- *  80 Mhz =>  80.000.000 / Divider = 156
- * 100 Mhz => 100.000.000 / Divider = 195
- */
-
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA	98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME		"SCC"
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/TQM862M.h b/include/configs/TQM862M.h
deleted file mode 100644
index ec3a57b..0000000
--- a/include/configs/TQM862M.h
+++ /dev/null
@@ -1,465 +0,0 @@
-/*
- * (C) Copyright 2000-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860		1
-#define CONFIG_MPC860T		1
-#define CONFIG_MPC862		1
-
-#define CONFIG_TQM862M		1	/* ...on a TQM8xxM module	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define	CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"hostname=TQM862M\0"						\
-	"bootfile=TQM862M/uImage\0"					\
-	"fdt_addr=40080000\0"						\
-	"kernel_addr=400A0000\0"					\
-	"ramdisk_addr=40280000\0"					\
-	"u-boot=TQM862M/u-image.bin\0"					\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"update=prot off 40000000 +${filesize};"			\
-		"era 40000000 +${filesize};"				\
-		"cp.b 200000 40000000 ${filesize};"			\
-		"sete filesize;save\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_NETCONSOLE
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
-#define	CONFIG_ENV_SIZE		0x08000	/* Total Size of Environment		*/
-#define	CONFIG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R		/* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
-
-#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
-						"128k(dtb),"		\
-						"1920k(kernel),"	\
-						"5632(rootfs),"		\
-						"4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef	CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #1	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef	CONFIG_CAN_DRIVER
-#define	CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define	CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- *  50 MHz =>  50.000.000 / Divider =  98
- *  66 Mhz =>  66.000.000 / Divider = 129
- *  80 Mhz =>  80.000.000 / Divider = 156
- * 100 Mhz => 100.000.000 / Divider = 195
- */
-
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA	98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME		"SCC"
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h
deleted file mode 100644
index cb8b84d..0000000
--- a/include/configs/TQM866M.h
+++ /dev/null
@@ -1,483 +0,0 @@
-/*
- * (C) Copyright 2000-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC866		1	/* This is a MPC866 CPU		*/
-#define CONFIG_TQM866M		1	/* ...on a TQM8xxM module	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define CONFIG_8xx_OSCLK		10000000	/*  10 MHz - PLL input clock	*/
-#define CONFIG_SYS_8xx_CPUCLK_MIN		15000000	/*  15 MHz - CPU minimum clock	*/
-#define CONFIG_SYS_8xx_CPUCLK_MAX		133000000	/* 133 MHz - CPU maximum clock	*/
-#define CONFIG_8xx_CPUCLK_DEFAULT	50000000	/*  50 MHz - CPU default clock	*/
-						/* (it will be used if there is no	*/
-						/* 'cpuclk' variable with valid value)	*/
-
-#undef CONFIG_SYS_MEASURE_CPUCLK			/* Measure real cpu clock	*/
-						/* (function measure_gclk()	*/
-						/* will be called)		*/
-#ifdef CONFIG_SYS_MEASURE_CPUCLK
-#define CONFIG_SYS_8XX_XIN		10000000	/* measure_gclk() needs this	*/
-#endif
-
-#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;" \
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"hostname=TQM866M\0"						\
-	"bootfile=TQM866M/uImage\0"					\
-	"fdt_addr=400C0000\0"						\
-	"kernel_addr=40100000\0"					\
-	"ramdisk_addr=40280000\0"					\
-	"u-boot=TQM866M/u-image.bin\0"					\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"update=prot off 40000000 +${filesize};"			\
-		"era 40000000 +${filesize};"				\
-		"cp.b 200000 40000000 ${filesize};"			\
-		"sete filesize;save\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL		0x00000020	/* PB 26 */
-#define PB_SDA		0x00000010	/* PB 27 */
-
-#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else	immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* EEPROM AT24C256	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2		/* two byte address	*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#undef CONFIG_RTC_MPC8xx		/* MPC866 does not support RTC	*/
-
-#define	CONFIG_TIMESTAMP		/* but print image timestmps	*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_NETCONSOLE
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_OFFSET		0x40000 /*   Offset   of Environment Sector	*/
-#define CONFIG_ENV_SIZE		0x08000 /* Total Size of Environment Sector	*/
-#define CONFIG_ENV_SECT_SIZE	0x40000 /* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R		/* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
-
-#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
-						"128k(dtb),"		\
-						"1920k(kernel),"	\
-						"5632(rootfs),"		\
-						"4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size	  of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing: Default value of OR0 after reset
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
-				 OR_SCY_15_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define SDRAM_MAX_SIZE		(256 << 20)	/* max 256 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*
- * 4096	Rows from SDRAM example configuration
- * 1000	factor s -> ms
- * 64	PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4	Number of refresh cycles per period
- * 64	Refresh cycle in ms per number of rows
- */
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 64 * 1000) / (4 * 64))
-
-/*
- * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad)
- *
- *                        CPUclock(MHz) * 31.2
- * CONFIG_SYS_MAMR_PTA = -----------------------------------     with DFBRG = 0
- *                2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16
- *
- * CPU clock =  15 MHz:  CONFIG_SYS_MAMR_PTA =  29   ->  4 * 7.73 us
- * CPU clock =  50 MHz:  CONFIG_SYS_MAMR_PTA =  97   ->  4 * 7.76 us
- * CPU clock =  66 MHz:  CONFIG_SYS_MAMR_PTA = 128   ->  4 * 7.75 us
- * CPU clock = 133 MHz:  CONFIG_SYS_MAMR_PTA = 255   ->  4 * 7.67 us
- *
- * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will
- * be met also in the default configuration, i.e. if environment variable
- * 'cpuclk' is not set.
- */
-#define CONFIG_SYS_MAMR_PTA		97
-
-/*
- * Memory Periodic Timer Prescaler Register (MPTPR) values.
- */
-/* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16
-/* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 10 column SDRAM */
-#define CONFIG_SYS_MAMR_10COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9  |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME		"SCC"
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/TQM885D.h b/include/configs/TQM885D.h
deleted file mode 100644
index d1e6c5b..0000000
--- a/include/configs/TQM885D.h
+++ /dev/null
@@ -1,482 +0,0 @@
-/*
- * (C) Copyright 2000-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2006
- * Martin Krause, TQ-Systems GmBH, martin.krause@tqs.de
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC885		1	/* This is a MPC885 CPU		*/
-#define CONFIG_TQM885D		1	/* ...on a TQM88D module	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define CONFIG_8xx_OSCLK		10000000	/*  10 MHz - PLL input clock	*/
-#define CONFIG_SYS_8xx_CPUCLK_MIN		15000000	/*  15 MHz - CPU minimum clock	*/
-#define CONFIG_SYS_8xx_CPUCLK_MAX		133000000	/* 133 MHz - CPU maximum clock	*/
-#define CONFIG_8xx_CPUCLK_DEFAULT	66000000	/*  66 MHz - CPU default clock	*/
-						/* (it will be used if there is no	*/
-						/* 'cpuclk' variable with valid value)	*/
-
-#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;" \
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM885D/uImage\0"				\
-	"fdt_addr=400C0000\0"						\
-	"kernel_addr=40100000\0"					\
-	"ramdisk_addr=40280000\0"					\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"update=protect off 40000000 +${filesize};"			\
-		"erase 40000000 +${filesize};"				\
-		"cp.b 200000 40000000 ${filesize};"			\
-		"protect on 40000000 +${filesize}\0"			\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL		0x00000020	/* PB 26 */
-#define PB_SDA		0x00000010	/* PB 27 */
-
-#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else	immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* EEPROM AT24C??	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2		/* two byte address	*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
-
-# define CONFIG_RTC_DS1337 1
-# define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#undef CONFIG_RTC_MPC8xx		/* MPC885 does not support RTC	*/
-
-#define	CONFIG_TIMESTAMP		/* but print image timestmps	*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0100000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0300000	/* 1 ... 3 MB in DRAM	*/
-#define CONFIG_SYS_ALT_MEMTEST				/* alternate, more extensive
-						   memory test.*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/*
- * Enable loopw command.
- */
-#define CONFIG_LOOPW
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_OFFSET		0x40000 /*   Offset   of Environment Sector	*/
-#define CONFIG_ENV_SIZE		0x08000 /* Total Size of Environment		*/
-#define CONFIG_ENV_SECT_SIZE	0x40000 /* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size	  of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing: Default value of OR0 after reset
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
-				 OR_SCY_6_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define SDRAM_MAX_SIZE		(256 << 20)	/* max 256 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*
- * 4096	Rows from SDRAM example configuration
- * 1000	factor s -> ms
- * 64	PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4	Number of refresh cycles per period
- * 64	Refresh cycle in ms per number of rows
- */
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 64 * 1000) / (4 * 64))
-
-/*
- * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad)
- *
- *                        CPUclock(MHz) * 31.2
- * CONFIG_SYS_MAMR_PTA = -----------------------------------     with DFBRG = 0
- *                2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16
- *
- * CPU clock =  15 MHz:  CONFIG_SYS_MAMR_PTA =  29   ->  4 * 7.73 us
- * CPU clock =  50 MHz:  CONFIG_SYS_MAMR_PTA =  97   ->  4 * 7.76 us
- * CPU clock =  66 MHz:  CONFIG_SYS_MAMR_PTA = 128   ->  4 * 7.75 us
- * CPU clock = 133 MHz:  CONFIG_SYS_MAMR_PTA = 255   ->  4 * 7.67 us
- *
- * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will
- * be met also in the default configuration, i.e. if environment variable
- * 'cpuclk' is not set.
- */
-#define CONFIG_SYS_MAMR_PTA		128
-
-/*
- * Memory Periodic Timer Prescaler Register (MPTPR) values.
- */
-/* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16
-/* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 10 column SDRAM */
-#define CONFIG_SYS_MAMR_10COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9  |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-/*
- * Network configuration
- */
-#define CONFIG_SCC2_ENET		/* enable ethernet on SCC2 */
-#define CONFIG_FEC_ENET			/* enable ethernet on FEC */
-#define CONFIG_ETHER_ON_FEC1		/* ... for FEC1 */
-#define CONFIG_ETHER_ON_FEC2		/* ... for FEC2 */
-
-#if defined(CONFIG_CMD_MII)
-#define CONFIG_SYS_DISCOVER_PHY
-#define CONFIG_MII_INIT	1
-#endif
-
-#define CONFIG_NET_RETRY_COUNT 1	/* reduce max. timeout before
-					   switching to another netwok (if the
-					   tried network is unreachable) */
-
-#define CONFIG_ETHPRIME		"SCC"
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/virtlab2.h b/include/configs/virtlab2.h
deleted file mode 100644
index 0457cdf..0000000
--- a/include/configs/virtlab2.h
+++ /dev/null
@@ -1,469 +0,0 @@
-/*
- * (C) Copyright 2006-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
-#define CONFIG_VIRTLAB2		1	/* ...on a virtlab2 module	*/
-#define	CONFIG_TQM8xxL		1
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define	CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"hostname=virtlab2\0"						\
-	"bootfile=virtlab2/uImage\0"					\
-	"fdt_addr=40040000\0"						\
-	"kernel_addr=40060000\0"					\
-	"ramdisk_addr=40200000\0"					\
-	"u-boot=virtlab2/u-image.bin\0"					\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"update=prot off 40000000 +${filesize};"			\
-		"era 40000000 +${filesize};"				\
-		"cp.b 200000 40000000 ${filesize};"			\
-		"sete filesize;save\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#if defined(CONFIG_LCD)
-# undef	 CONFIG_STATUS_LED		/* disturbs display		*/
-#else
-# define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-#endif	/* CONFIG_LCD */
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-#if defined(CONFIG_SPLASH_SCREEN)
-    #define CONFIG_CMD_BMP
-#endif
-
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define	CONFIG_SYS_HUSH_PARSER		1	/* use "hush" command parser	*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE+flash_info[0].size }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
-#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R		/* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT		"nor0=TQM8xxL-0"
-
-#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxL-0:256k(u-boot),"	\
-						"128k(dtb),"		\
-						"1664k(kernel),"	\
-						"2m(rootfs),"		\
-						"4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef	CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef	CONFIG_CAN_DRIVER
-#define	CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define	CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA	98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-/* Map peripheral control registers on CS4 */
-#define CONFIG_SYS_PERIPHERAL_BASE 0xA0000000
-#define CONFIG_SYS_PERIPHERAL_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR4_PRELIM (CONFIG_SYS_PERIPHERAL_OR_AM | OR_TRLX | OR_CSNT_SAM | \
-						OR_SCY_2_CLK)
-#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_PERIPHERAL_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
-#define PCMCIA_CTRL (CONFIG_SYS_PERIPHERAL_BASE + 0xB00)
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
