diff mbox

[U-Boot] MPC824x: remove obsolete "PN62" board

Message ID 1384197139-7991-1-git-send-email-wd@denx.de
State Accepted
Delegated to: Tom Rini
Headers show

Commit Message

Wolfgang Denk Nov. 11, 2013, 7:12 p.m. UTC
The MPC824x processors have long reached EOL, and the PN62 board has
not seen any board-specific updates for more than a decade.  It is now
causing build issues.  Instead of wasting time on things nobody is
interested in any more, we rather drop this board.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
cc: Tom Rini <trini@ti.com>
---
Tom, as there is zero activity for the MPC82xx tree I don't invest the
efforts in pushing this patch there and then sending a pull request.
Can you please apply it directly?  Thanks in advance -- wd

 CREDITS                             |   2 +-
 arch/powerpc/cpu/mpc824x/cpu_init.c |   6 +-
 board/pn62/Makefile                 |   8 -
 board/pn62/cmd_pn62.c               | 146 ------------------
 board/pn62/misc.c                   | 219 ---------------------------
 board/pn62/pn62.c                   | 171 ----------------------
 board/pn62/pn62.h                   | 145 ------------------
 boards.cfg                          |   1 -
 doc/README.scrapyard                |   3 +-
 drivers/net/pcnet.c                 |  10 --
 include/configs/PN62.h              | 285 ------------------------------------
 11 files changed, 5 insertions(+), 991 deletions(-)
 delete mode 100644 board/pn62/Makefile
 delete mode 100644 board/pn62/cmd_pn62.c
 delete mode 100644 board/pn62/misc.c
 delete mode 100644 board/pn62/pn62.c
 delete mode 100644 board/pn62/pn62.h
 delete mode 100644 include/configs/PN62.h

Comments

Tom Rini Nov. 11, 2013, 9:41 p.m. UTC | #1
On Mon, Nov 11, 2013 at 08:12:19PM +0100, Wolfgang Denk wrote:

> The MPC824x processors have long reached EOL, and the PN62 board has
> not seen any board-specific updates for more than a decade.  It is now
> causing build issues.  Instead of wasting time on things nobody is
> interested in any more, we rather drop this board.
> 
> Signed-off-by: Wolfgang Denk <wd@denx.de>
> Cc: Wolfgang Grandegger <wg@grandegger.com>
> cc: Tom Rini <trini@ti.com>

Applied to u-boot/master, thanks!
diff mbox

Patch

diff --git a/CREDITS b/CREDITS
index 3b657e9..52f289e 100644
--- a/CREDITS
+++ b/CREDITS
@@ -143,7 +143,7 @@  W: www.freescale.com
 
 N: Dr. Wolfgang Grandegger
 E: wg@denx.de
-D: Support for Interphase 4539 T1/E1/J1 PMC, PN62, CCM, SCM boards
+D: Support for Interphase 4539 T1/E1/J1 PMC, CCM, SCM boards
 W: www.denx.de
 
 N: Peter Figuli
diff --git a/arch/powerpc/cpu/mpc824x/cpu_init.c b/arch/powerpc/cpu/mpc824x/cpu_init.c
index 37d796e..47ac18e 100644
--- a/arch/powerpc/cpu/mpc824x/cpu_init.c
+++ b/arch/powerpc/cpu/mpc824x/cpu_init.c
@@ -52,7 +52,7 @@  cpu_init_f (void)
     CONFIG_WRITE_HALFWORD(PCICR, 0x06); /* Bus Master, respond to PCI memory space acesses*/
 /*    CONFIG_WRITE_HALFWORD(PCISR, 0xffff); */ /*reset PCISR*/
 
-#if defined(CONFIG_MUSENKI) || defined(CONFIG_PN62)
+#if defined(CONFIG_MUSENKI)
 /* Why is this here, you ask?  Try, just try setting 0x8000
  * in PCIACR with CONFIG_WRITE_HALFWORD()
  * this one was a stumper, and we are annoyed
@@ -142,9 +142,7 @@  cpu_init_f (void)
 
 	CONFIG_READ_WORD(PICR2, val);
 	val= val & ~ (PICR2_CF_SNOOP_WS_MASK | PICR2_CF_APHASE_WS_MASK); /*mask off waitstate bits*/
-#ifndef CONFIG_PN62
 	val |= PICR2_CF_SNOOP_WS_1WS | PICR2_CF_APHASE_WS_1WS; /*1 wait state*/
-#endif
 	CONFIG_WRITE_WORD(PICR2, val);
 
 	CONFIG_WRITE_WORD(EUMBBAR, CONFIG_SYS_EUMB_ADDR);
@@ -186,7 +184,7 @@  cpu_init_f (void)
  *  should define CONFIG_SYS_ACTORW to 0 if they don't want to set it, or even, if
  *  its not set, we define it to zero in this file
  */
-#if defined(CONFIG_CU824) || defined(CONFIG_PN62)
+#if defined(CONFIG_CU824)
 	CONFIG_WRITE_WORD(MCCR4,
 	(CONFIG_SYS_PRETOACT << MCCR4_PRETOACT_SHIFT) |
 	(CONFIG_SYS_ACTTOPRE << MCCR4_ACTTOPRE_SHIFT) |
diff --git a/board/pn62/Makefile b/board/pn62/Makefile
deleted file mode 100644
index 7572ed8..0000000
--- a/board/pn62/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@ 
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= pn62.o cmd_pn62.o misc.o
diff --git a/board/pn62/cmd_pn62.c b/board/pn62/cmd_pn62.c
deleted file mode 100644
index a0326b4..0000000
--- a/board/pn62/cmd_pn62.c
+++ /dev/null
@@ -1,146 +0,0 @@ 
-/*
- * (C) Copyright 2002
- * Wolfgang Grandegger, DENX Software Engineering, wg@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <malloc.h>
-#include <net.h>
-#include <asm/io.h>
-#include <pci.h>
-#include <command.h>
-#include "pn62.h"
-
-#if defined(CONFIG_CMD_BSP)
-
-/*
- * Command led: controls the various LEDs 0..11 on the PN62 card.
- */
-int do_led(cmd_tbl_t * cmdtp, int flag, int argc, char *const argv[])
-{
-	unsigned int number, function;
-
-	if (argc != 3)
-		return cmd_usage(cmdtp);
-
-	number = simple_strtoul(argv[1], NULL, 10);
-	if (number > PN62_LED_MAX)
-		return 1;
-
-	function = simple_strtoul(argv[2], NULL, 16);
-	set_led(number, function);
-	return 0;
-}
-U_BOOT_CMD(
-	led    ,	3,	1,	do_led,
-	"set LED 0..11 on the PN62 board",
-	"i fun"
-	"    - set 'i'th LED to function 'fun'"
-);
-
-/*
- * Command loadpci: loads a image over PCI.
- */
-#define CMD_MOVE_WINDOW 0x1
-#define CMD_BOOT_IMAGE  0x2
-
-int do_loadpci (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-    char *s;
-    ulong addr = 0, count = 0;
-    u32 off;
-    int cmd, rcode = 0;
-
-    /* pre-set load_addr */
-    if ((s = getenv("loadaddr")) != NULL) {
-	addr = simple_strtoul(s, NULL, 16);
-    }
-
-    switch (argc) {
-    case 1:
-	break;
-    case 2:
-	addr = simple_strtoul(argv[1], NULL, 16);
-	break;
-    default:
-	return cmd_usage(cmdtp);
-    }
-
-    printf ("## Ready for image download ...\n");
-
-    show_startup_phase(12);
-
-    while (1) {
-	/* Alive indicator */
-	i2155x_write_scrapad(BOOT_PROTO, BOOT_PROTO_READY);
-
-	/* Toggle status LEDs */
-	cmd = (count / 200) % 4; /* downscale */
-	set_led(4, cmd == 0 ? LED_1 : LED_0);
-	set_led(5, cmd == 1 ? LED_1 : LED_0);
-	set_led(6, cmd == 2 ? LED_1 : LED_0);
-	set_led(7, cmd == 3 ? LED_1 : LED_0);
-	udelay(1000);
-	count++;
-
-	cmd = i2155x_read_scrapad(BOOT_CMD);
-
-	if (cmd == BOOT_CMD_MOVE) {
-	    off = i2155x_read_scrapad(BOOT_DATA);
-	    off += addr;
-	    i2155x_set_bar_base(3, off);
-	    printf ("## BAR3 Addr moved = 0x%08x\n", off);
-	    i2155x_write_scrapad(BOOT_CMD, ~cmd);
-	    show_startup_phase(13);
-	}
-	else if (cmd == BOOT_CMD_BOOT) {
-	    set_led(4, LED_1);
-	    set_led(5, LED_1);
-	    set_led(6, LED_1);
-	    set_led(7, LED_1);
-
-	    i2155x_write_scrapad(BOOT_CMD, ~cmd);
-	    show_startup_phase(14);
-	    break;
-	}
-
-	/* Abort if ctrl-c was pressed */
-	if (ctrlc()) {
-	    printf("\nAbort\n");
-	    return 0;
-	}
-
-    }
-
-    /* Repoint to the default shared memory */
-    i2155x_set_bar_base(3, PN62_SMEM_DEFAULT);
-
-    load_addr = addr;
-    printf ("## Start Addr      = 0x%08lx\n", addr);
-
-    show_startup_phase(15);
-
-    /* Loading ok, check if we should attempt an auto-start */
-    if (((s = getenv("autostart")) != NULL) && (strcmp(s,"yes") == 0)) {
-	char *local_args[2];
-	local_args[0] = argv[0];
-	local_args[1] = NULL;
-
-	printf ("Automatic boot of image at addr 0x%08lX ...\n",
-		load_addr);
-	rcode = do_bootm (cmdtp, 0, 1, local_args);
-    }
-
-    return rcode;
-}
-
-U_BOOT_CMD(
-	loadpci,	2,	1,	do_loadpci,
-	"load binary file over PCI",
-	"[addr]\n"
-	"    - load binary file over PCI to address 'addr'"
-);
-
-#endif
diff --git a/board/pn62/misc.c b/board/pn62/misc.c
deleted file mode 100644
index 98e0dfa..0000000
--- a/board/pn62/misc.c
+++ /dev/null
@@ -1,219 +0,0 @@ 
-/*
- * (C) Copyright 2002 Wolfgang Grandegger <wg@denx.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/io.h>
-#include <pci.h>
-
-#include "pn62.h"
-
-typedef struct {
-    pci_dev_t    devno;
-    volatile u32 *csr;
-
-} i2155x_t;
-
-static i2155x_t i2155x = { 0, NULL };
-
-static struct pci_device_id i2155x_ids[] = {
-    { 0x1011, 0x0046 },		/* i21554 */
-    { 0x8086, 0xb555 }		/* i21555 */
-};
-
-int i2155x_init(void)
-{
-    pci_dev_t devno;
-    u32 val;
-    int i;
-
-    /*
-     * Find the Intel bridge.
-     */
-    if ((devno = pci_find_devices(i2155x_ids, 0)) < 0) {
-	printf("Error: Intel bridge 2155x not found!\n");
-	return -1;
-    }
-    i2155x.devno = devno;
-
-    /*
-     * Get auto-configured base address for CSR access.
-     */
-    pci_read_config_dword(devno, PCI_BASE_ADDRESS_1, &val);
-    if (val & PCI_BASE_ADDRESS_SPACE_IO) {
-	val &= PCI_BASE_ADDRESS_IO_MASK;
-	i2155x.csr = (volatile u32 *)(_IO_BASE + val);
-    } else {
-	val &= PCI_BASE_ADDRESS_MEM_MASK;
-	i2155x.csr =  (volatile u32 *)val;
-    }
-
-    /*
-     * Translate downstream memory 2 (bar3) to base of shared memory.
-     */
-    i2155x_set_bar_base(3, PN62_SMEM_DEFAULT);
-
-    /*
-     * Enable memory space, I/O space and bus master bits
-     * in both Primary and Secondary command registers.
-     */
-    val = PCI_COMMAND_MEMORY|PCI_COMMAND_MASTER|PCI_COMMAND_IO;
-    pci_write_config_word(devno, 0x44, val);
-    pci_write_config_word(devno, 0x04, val);
-
-    /*
-     * Clear scratchpad registers.
-     */
-    for (i = 0; i < (I2155X_SCRAPAD_MAX - 1); i++) {
-	i2155x_write_scrapad(i, 0x0);
-    }
-
-    /*
-     * Set interrupt line for Linux.
-     */
-    pci_write_config_byte(devno, PCI_INTERRUPT_LINE, 3);
-
-    return 0;
-}
-
-/*
- * Access the Scratchpad registers 0..7 of the Intel bridge.
- */
-void i2155x_write_scrapad(int idx, u32 val)
-{
-    if (idx >= 0 && idx < I2155X_SCRAPAD_MAX)
-	out_le32(i2155x.csr + (I2155X_SCRAPAD_ADDR/4) + idx, val);
-    else
-	printf("i2155x_write_scrapad: invalid index\n");
-}
-
-u32 i2155x_read_scrapad(int idx)
-{
-    if (idx >= 0 && idx < I2155X_SCRAPAD_MAX)
-	return in_le32(i2155x.csr + (I2155X_SCRAPAD_ADDR/4) + idx);
-    else
-	printf("i2155x_read_scrapad: invalid index\n");
-    return -1;
-}
-
-void i2155x_set_bar_base(int bar, u32 base)
-{
-    if (bar >= 2 && bar <= 4) {
-	pci_write_config_dword(i2155x.devno,
-			       I2155X_BAR2_BASE + (bar - 2) * 4,
-			       base);
-    }
-}
-
-/*
- * Read Vital Product Data (VPD) from the Serial EPROM attached
- * to the Intel bridge.
- */
-int i2155x_read_vpd(int offset, int size, unsigned char *data)
-{
-    int i, n;
-    u16 val16;
-
-    for (i = 0; i < size; i++) {
-	pci_write_config_word(i2155x.devno, I2155X_VPD_ADDR,
-			      offset + i - I2155X_VPD_START);
-	for (n = 10000; n > 0; n--) {
-	    pci_read_config_word(i2155x.devno, I2155X_VPD_ADDR, &val16);
-	    if ((val16 & 0x8000) != 0) /* wait for completion */
-		break;
-	    udelay(100);
-	}
-	if (n == 0) {
-	    printf("i2155x_read_vpd: TIMEOUT\n");
-	    return -1;
-	}
-
-	pci_read_config_byte(i2155x.devno, I2155X_VPD_DATA, &data[i]);
-    }
-
-    return i;
-}
-
-static struct pci_device_id am79c95x_ids [] = {
-	{ PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_LANCE },
-	{ }
-};
-
-
-/*
- * Initialize the AMD ethernet controllers.
- */
-int am79c95x_init(void)
-{
-    pci_dev_t devno;
-    int i;
-
-    /*
-     * Set interrupt line for Linux.
-     */
-    for (i = 0; i < 2; i++) {
-	if ((devno = pci_find_devices(am79c95x_ids, i)) < 0)
-	    break;
-	pci_write_config_byte(devno, PCI_INTERRUPT_LINE, 2+i);
-    }
-    if (i < 2)
-	printf("Error: Only %d AMD Ethernet Controller found!\n", i);
-
-    return 0;
-}
-
-
-void set_led(unsigned int number, unsigned int function)
-{
-    volatile u8 *addr;
-
-    if ((number >= 0) && (number < PN62_LED_MAX) &&
-	(function >= 0) && (function <= LED_LAST_FUNCTION)) {
-	addr = (volatile u8 *)(PN62_LED_BASE + number * 8);
-	out_8(addr, function&0xff);
-    }
-}
-
-/*
- * Show fatal error indicated by Kinght Rider(tm) effect
- * in LEDS 0-7. LEDS 8-11 contain 4 bit error code.
- * Note: this function will not terminate.
- */
-void fatal_error(unsigned int error_code)
-{
-    int i, d;
-
-    for (i = 0; i < 12; i++) {
-	set_led(i, LED_0);
-    }
-
-    /*
-     * Write error code.
-     */
-    set_led(8,  (error_code & 0x01) ? LED_1 : LED_0);
-    set_led(9,  (error_code & 0x02) ? LED_1 : LED_0);
-    set_led(10, (error_code & 0x04) ? LED_1 : LED_0);
-    set_led(11, (error_code & 0x08) ? LED_1 : LED_0);
-
-    /*
-     * Yay - Knight Rider effect!
-     */
-    while(1) {
-	unsigned int delay = 2000;
-
-	for (i = 0; i < 8; i++) {
-	    set_led(i, LED_1);
-	    for (d = 0; d < delay; d++);
-	    set_led(i, LED_0);
-	}
-
-	for (i = 7; i > 0; i--) {
-	    set_led(i, LED_1);
-	    for (d = 0; d < delay; d++);
-	    set_led(i, LED_0);
-	}
-    }
-}
diff --git a/board/pn62/pn62.c b/board/pn62/pn62.c
deleted file mode 100644
index 81829dd..0000000
--- a/board/pn62/pn62.c
+++ /dev/null
@@ -1,171 +0,0 @@ 
-/*
- * (C) Copyright 2002 Wolfgang Grandegger <wg@denx.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <net.h>
-#include <pci.h>
-#include <netdev.h>
-
-#include "pn62.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static int get_serial_number (char *string, int size);
-static void get_mac_address(int id, u8 *mac);
-
-#ifdef CONFIG_SHOW_BOOT_PROGRESS
-void show_boot_progress (int phase)
-{
-	/*
-	 * Show phases of the bootm command on the front panel
-	 * LEDs and the scratchpad register #3 as well. We use
-	 * blinking LEDs for logical "1".
-	 */
-	if (phase > 0) {
-		set_led (8, (phase & 0x1) ? LED_SLOW_CLOCK : LED_0);
-		set_led (9, (phase & 0x2) ? LED_SLOW_CLOCK : LED_0);
-		set_led (10, (phase & 0x4) ? LED_SLOW_CLOCK : LED_0);
-		set_led (11, (phase & 0x8) ? LED_SLOW_CLOCK : LED_0);
-	}
-	i2155x_write_scrapad (BOOT_STATUS, phase);
-	if (phase < 0)
-		i2155x_write_scrapad (BOOT_DONE, BOOT_DONE_ERROR);
-}
-#endif
-
-void show_startup_phase (int phase)
-{
-	/*
-	 * Show the phase of U-Boot startup on the front panel
-	 * LEDs and the scratchpad register #3 as well.
-	 */
-	if (phase > 0) {
-		set_led (8, (phase & 0x1) ? LED_1 : LED_0);
-		set_led (9, (phase & 0x2) ? LED_1 : LED_0);
-		set_led (10, (phase & 0x4) ? LED_1 : LED_0);
-		set_led (11, (phase & 0x8) ? LED_1 : LED_0);
-	}
-	i2155x_write_scrapad (BOOT_STATUS, phase);
-	if (phase < 0)
-		i2155x_write_scrapad (BOOT_DONE, BOOT_DONE_ERROR);
-}
-
-int checkboard (void)
-{
-	show_startup_phase (1);
-	puts ("Board: PN62\n");
-	return 0;
-}
-
-phys_size_t initdram (int board_type)
-{
-	long size;
-	long new_bank0_end;
-	long mear1;
-	long emear1;
-
-	show_startup_phase (2);
-
-	size = get_ram_size(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MAX_RAM_SIZE);
-
-	new_bank0_end = size - 1;
-	mear1 = mpc824x_mpc107_getreg (MEAR1);
-	emear1 = mpc824x_mpc107_getreg (EMEAR1);
-	mear1 = (mear1 & 0xFFFFFF00) |
-		((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
-	emear1 = (emear1 & 0xFFFFFF00) |
-		((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
-	mpc824x_mpc107_setreg (MEAR1, mear1);
-	mpc824x_mpc107_setreg (EMEAR1, emear1);
-
-	return (size);
-}
-
-/*
- * Initialize PCI Devices. We rely on auto-configuration.
- */
-#ifndef CONFIG_PCI_PNP
-#error "CONFIG_PCI_PNP is not defined, please correct!"
-#endif
-
-struct pci_controller hose = {
-};
-
-void pci_init_board (void)
-{
-	show_startup_phase (4);
-	pci_mpc824x_init (&hose);
-
-	show_startup_phase (5);
-	i2155x_init ();
-	show_startup_phase (6);
-	am79c95x_init ();
-	show_startup_phase (7);
-}
-
-int misc_init_r (void)
-{
-	char str[20];
-	u8 mac[6];
-
-	show_startup_phase (8);
-	/*
-	 * Get serial number and ethernet addresses if not already defined
-	 * and update the board info structure and the environment.
-	 */
-	if (getenv ("serial#") == NULL &&
-		get_serial_number (str, strlen (str)) > 0) {
-		setenv ("serial#", str);
-	}
-	show_startup_phase (9);
-
-	if (!eth_getenv_enetaddr("ethaddr", mac)) {
-		get_mac_address(0, mac);
-		eth_setenv_enetaddr("ethaddr", mac);
-	}
-	show_startup_phase (10);
-
-#ifdef CONFIG_HAS_ETH1
-	if (!eth_getenv_enetaddr("eth1addr", mac)) {
-		get_mac_address(1, mac);
-		eth_setenv_enetaddr("eth1addr", mac);
-	}
-#endif /* CONFIG_HAS_ETH1 */
-	show_startup_phase (11);
-
-	/* Tell everybody that U-Boot is up and runnig */
-	i2155x_write_scrapad (0, 0x12345678);
-	return (0);
-}
-
-static int get_serial_number (char *string, int size)
-{
-	int i;
-	char c;
-
-	if (size < I2155X_VPD_SN_SIZE)
-		size = I2155X_VPD_SN_SIZE;
-	for (i = 0; i < (size - 1); i++) {
-		i2155x_read_vpd (I2155X_VPD_SN_START + i, 1, (uchar *)&c);
-		if (c == '\0')
-			break;
-		string[i] = c;
-	}
-	string[i] = '\0';			/* make sure it's terminated */
-
-	return i;
-}
-
-static void get_mac_address(int id, u8 *mac)
-{
-	i2155x_read_vpd (I2155X_VPD_MAC0_START + 6 * id, 6, mac);
-}
-
-int board_eth_init(bd_t *bis)
-{
-	return pci_eth_init(bis);
-}
diff --git a/board/pn62/pn62.h b/board/pn62/pn62.h
deleted file mode 100644
index 10290c3..0000000
--- a/board/pn62/pn62.h
+++ /dev/null
@@ -1,145 +0,0 @@ 
-/*
- * (C) Copyright 2002 Wolfgang Grandegger <wg@denx.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef _PN62_H_
-#define _PN62_H_
-
-/*
- * Definitions for the Intel Bridge 21554 or 21555.
- */
-#define I2155X_VPD_ADDR		0xe6
-#define I2155X_VPD_DATA		0xe8
-
-#define I2155X_VPD_START	0x80
-#define I2155X_VPD_SN_START	0x80
-#define I2155X_VPD_SN_SIZE	0x10
-#define I2155X_VPD_MAC0_START	0x90
-#define I2155X_VPD_MAC1_START	0x96
-
-#define I2155X_SCRAPAD_ADDR	0xa8
-#define I2155X_SCRAPAD_MAX	8
-
-#define I2155X_BAR2_BASE	0x98
-#define I2155X_BAR3_BASE	0x9c
-#define I2155X_BAR4_BASE	0xa0
-
-#define I2155X_BAR2_SETUP	0xb0
-#define I2155X_BAR3_SETUP	0xb4
-#define I2155X_BAR4_SETUP	0xb8
-
-/*
- * Interrupt request numbers
- */
-#define PN62_IRQ_HOST		0x0
-#define PN62_IRQ_PLX9054	0x1
-#define PN62_IRQ_ETH0		0x2
-#define PN62_IRQ_ETH1		0x3
-#define PN62_IRQ_COM1		0x4
-#define PN62_IRQ_COM2		0x4
-
-/*
- * Miscellaneous definitons.
- */
-#define PN62_SMEM_DEFAULT	0x1f00000
-
-/*
- * Definitions for boot protocol using Scratchpad registers.
- */
-#define BOOT_DONE		0
-#define BOOT_DONE_CLEAR		0x00dead00
-#define BOOT_DONE_ERROR		0xbad0dead
-#define BOOT_DONE_U_BOOT	0x12345678
-#define BOOT_DONE_LINUX		0x87654321
-#define BOOT_CMD		1
-#define BOOT_CMD_MOVE		0x1
-#define BOOT_CMD_BOOT		0x2
-#define BOOT_DATA		2
-#define BOOT_PROTO		3
-#define BOOT_PROTO_READY	0x23456789
-#define BOOT_PROTO_CLEAR	0x00000000
-#define BOOT_STATUS		4
-
-/*
- * LED Definitions:
- */
-#define PN62_LED_BASE		0xff800300
-#define PN62_LED_MAX		12
-
-/*
- * LED0 - 7 mounted on top of board, D1 - D8
- * LED8 - 11 upper four LEDs on the front panel of the board.
- */
-#define LED_0			0x00	/* OFF */
-#define LED_1			0x01	/* ON */
-#define LED_SLOW_CLOCK		0x02	/* SLOW 1Hz ish */
-#define LED_nSLOW_CLOCK		0x03	/* inverse of above */
-#define LED_WATCHDOG_OUT	0x06	/* Reset Watchdog level */
-#define LED_WATCHDOG_CLOCK	0x07	/* clock to watchdog */
-
-/*
- * LED's currently setup in AMD79C973 device as the following:
- * LED0 100Mbit
- * LED1 LNKSE
- * LED2 TX Activity
- * LED3 RX Activity
- */
-#define LED_E0_LED0		0x08	/* Ethernet Port 0 LED 0 */
-#define LED_E0_LED1		0x09	/* Ethernet Port 0 LED 1 */
-#define LED_E0_LED2		0x0A	/* Ethernet Port 0 LED 2 */
-#define LED_E0_LED3		0x0B	/* Ethernet Port 0 LED 3 */
-#define LED_E1_LED0		0x0C	/* Ethernet Port 1 LED 0 */
-#define LED_E1_LED1		0x0D	/* Ethernet Port 1 LED 1 */
-#define LED_E1_LED2		0x0E	/* Ethernet Port 1 LED 2 */
-#define LED_E1_LED3		0x0F	/* Ethernet Port 1 LED 3 */
-#define LED_STROBE0		0x10	/* Processor Strobe 0 */
-#define LED_STROBE1		0x11	/* Processor Strobe 1 */
-#define LED_STROBE2		0x12	/* Processor Strobe 2 */
-#define LED_STROBE3		0x13	/* Processor Strobe 3 */
-#define LED_STROBE4		0x14	/* Processor Strobe 4 */
-#define LED_STROBE5		0x15	/* Processor Strobe 5 */
-#define LED_STROBE6		0x16	/* Processor Strobe 6 */
-#define LED_STROBE7		0x17	/* Processor Strobe 7 */
-#define LED_HOST_STROBE0	0x18	/* Host strobe 0 */
-#define LED_HOST_STROBE1	0x19	/* Host strobe 1 */
-#define LED_HOST_STROBE2	0x1A	/* Host strobe 2 */
-#define LED_HOST_STROBE3	0x1B	/* Host strobe 3 */
-#define LED_HOST_STROBE4	0x1C	/* Host strobe 4 */
-#define LED_HOST_STROBE5	0x1D	/* Host strobe 5 */
-#define LED_HOST_STROBE6	0x1E	/* Host strobe 6 */
-#define LED_HOST_STROBE7	0x1F	/* Host strobe 7 */
-#define LED_MPC_INT0		0x20	/* MPC8240 INT 0 */
-#define LED_MPC_INT1		0x21	/* MPC8240 INT 1 */
-#define	LED_MPC_INT2		0x22	/* MPC8240 INT 2 */
-#define	LED_MPC_INT3		0x23	/* MPC8240 INT 3 */
-#define	LED_MPC_INT4		0x24	/* MPC8240 INT 4 */
-#define	LED_UART0_CS		0x25	/* UART 0 Chip Select */
-#define	LED_UART1_CS		0x26	/* UART 1 Chip Select */
-#define	LED_SRAM_CS		0x27	/* SRAM Chip Select */
-#define	LED_SRAM_WR		0x28	/* SRAM WR Signal */
-#define	LED_SRAM_RD		0x29	/* SRAM RD Signal */
-#define	LED_MPC_RCS0		0x2A	/* MPC8240 RCS0 Signal */
-#define	LED_S_PCI_FRAME		0x2B	/* Secondary PCI Frame Signal */
-#define	LED_MPC_CS0		0x2C	/* MPC8240 CS0 Signal */
-#define	LED_HOST_INT		0x2D	/* MPC8240 to Host Interrupt signal */
-#define LED_LAST_FUNCTION	LED_HOST_INT	/* last function */
-
-/*
- * Forward declarations
- */
-int  i2155x_init	 (void);
-void i2155x_write_scrapad(int idx, u32 val);
-u32  i2155x_read_scrapad (int idx);
-void i2155x_set_bar_base (int bar, u32 addr);
-int  i2155x_read_vpd	 (int offset, int size, unsigned char *data);
-
-int  am79c95x_init	 (void);
-
-void set_led		 (unsigned int number, unsigned int function);
-void fatal_error	 (unsigned int error_code);
-void show_startup_phase  (int phase);
-
-
-#endif /* _PN62_H_ */
diff --git a/boards.cfg b/boards.cfg
index 375f2d4..1a48ff0 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -630,7 +630,6 @@  Active  powerpc     mpc824x        -           -               hidden_dragon
 Active  powerpc     mpc824x        -           -               linkstation         linkstation_HGLAN                    linkstation:HGLAN=1                                                                                                               Guennadi Liakhovetski <g.liakhovetski@gmx.de>
 Active  powerpc     mpc824x        -           -               musenki             MUSENKI                              -                                                                                                                                 Jim Thompson <jim@musenki.com>
 Active  powerpc     mpc824x        -           -               mvblue              MVBLUE                               -                                                                                                                                 -
-Active  powerpc     mpc824x        -           -               pn62                PN62                                 -                                                                                                                                 Wolfgang Grandegger <wg@denx.de>
 Active  powerpc     mpc824x        -           -               sandpoint           Sandpoint8240                        -                                                                                                                                 Wolfgang Denk <wd@denx.de>
 Active  powerpc     mpc824x        -           -               sandpoint           Sandpoint8245                        -                                                                                                                                 Jim Thompson <jim@musenki.com>
 Active  powerpc     mpc824x        -           etin            -                   debris                               -                                                                                                                                 Sangmoon Kim <dogoil@etinsys.com>
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 7cfb3a3..e1d5f62 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -11,7 +11,8 @@  easily if here is something they might want to dig for...
 
 Board            Arch        CPU            Commit      Removed     Last known maintainer/contact
 =================================================================================================
-omap1510inn      arm         arm925t        -           -           Kshitij Gupta <kshitij@ti.com>
+pn62		 powerpc     mpc824x	    -		-	    Wolfgang Grandegger <wg@grandegger.com>
+omap1510inn      arm         arm925t        0610a16	2013-10-07  Kshitij Gupta <kshitij@ti.com>
 CANBT            powerpc     405CR          fb8f4fd     2013-08-07  Matthias Fuchs <matthias.fuchs@esd.eu>
 Alaska8220       powerpc     mpc8220        d6ed322     2013-05-11
 Yukon8220        powerpc     mpc8220        d6ed322     2013-05-11
diff --git a/drivers/net/pcnet.c b/drivers/net/pcnet.c
index 283cb48..46cef5f 100644
--- a/drivers/net/pcnet.c
+++ b/drivers/net/pcnet.c
@@ -290,16 +290,6 @@  static int pcnet_init (struct eth_device *dev, bd_t * bis)
 	/* Switch pcnet to 32bit mode */
 	pcnet_write_bcr (dev, 20, 2);
 
-#ifdef CONFIG_PN62
-	/* Setup LED registers */
-	val = pcnet_read_bcr (dev, 2) | 0x1000;
-	pcnet_write_bcr (dev, 2, val);	/* enable LEDPE */
-	pcnet_write_bcr (dev, 4, 0x5080);	/* 100MBit */
-	pcnet_write_bcr (dev, 5, 0x40c0);	/* LNKSE */
-	pcnet_write_bcr (dev, 6, 0x4090);	/* TX Activity */
-	pcnet_write_bcr (dev, 7, 0x4084);	/* RX Activity */
-#endif
-
 	/* Set/reset autoselect bit */
 	val = pcnet_read_bcr (dev, 2) & ~2;
 	val |= 2;
diff --git a/include/configs/PN62.h b/include/configs/PN62.h
deleted file mode 100644
index 2a82f94..0000000
--- a/include/configs/PN62.h
+++ /dev/null
@@ -1,285 +0,0 @@ 
-/*
- * (C) Copyright 2002
- * Wolfgang Grandegger, DENX Software Engineering, wg@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC824X		1
-#define CONFIG_MPC8240		1
-#define CONFIG_PN62		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF00000
-
-#define CONFIG_CONS_INDEX	1
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_BSP
-
-#undef CONFIG_CMD_FLASH
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_SAVEENV
-#undef CONFIG_CMD_SOURCE
-
-
-#define CONFIG_BAUDRATE		19200	/* console baudrate		*/
-
-#define CONFIG_BOOTDELAY	1	/* autoboot after n seconds	*/
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#define CONFIG_SERVERIP		10.0.0.201
-#define CONFIG_IPADDR		10.0.0.200
-#define CONFIG_ROOTPATH		"/opt/eldk/ppc_82xx"
-#define CONFIG_NETMASK		255.255.255.0
-#undef CONFIG_BOOTARGS
-#if 0
-/* Boot Linux with NFS root filesystem */
-#define CONFIG_BOOTCOMMAND \
-			"setenv verify y;" \
-			"setenv bootargs console=ttyS0,19200 mem=31M quiet " \
-			"root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
-			"ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \
-			"loadp 100000; bootm"
-			/* "tftpboot 100000 uImage; bootm" */
-#else
-/* Boot Linux with RAMdisk based filesystem (initrd, BusyBox) */
-#define CONFIG_BOOTCOMMAND \
-			"setenv verify n;" \
-			"setenv bootargs console=ttyS0,19200 mem=31M quiet " \
-			"root=/dev/ram rw " \
-			"ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \
-			"loadp 200000; bootm"
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP		1		/* undef to save memory		*/
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size	*/
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-#define CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address		*/
-
-#define CONFIG_PRAM		1024		/* reserve 1 MB protected RAM	*/
-
-#define CONFIG_MISC_INIT_R	1		/* call misc_init_r() on init	*/
-
-#define CONFIG_HAS_ETH1		1		/* add support for eth1addr	*/
-
-#define CONFIG_SHOW_BOOT_PROGRESS 1		/* Show boot progress on LEDs   */
-
-/*
- * PCI stuff
- */
-#define CONFIG_PCI				/* include pci support		*/
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_PNP				/* we need Plug 'n Play		*/
-#if 0
-#define CONFIG_PCI_SCAN_SHOW			/* show PCI auto-scan at boot	*/
-#endif
-
-/*
- * Networking stuff
- */
-
-#define CONFIG_PCNET				/* there are 2 AMD PCnet 79C973	*/
-#define CONFIG_PCNET_79C973
-
-#define _IO_BASE		0xfe000000	/* points to PCI I/O space	*/
-
-
-/*
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE	0x10000000
-
-#define CONFIG_SYS_RESET_ADDRESS	0xfff00100
-
-#undef	CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_MONITOR_LEN		0x00030000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-
-
-#define CONFIG_SYS_INIT_RAM_ADDR	0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-
-#define CONFIG_SYS_NO_FLASH		1		/* There is no FLASH memory	*/
-
-#define CONFIG_ENV_IS_NOWHERE	1		/* Store ENV in memory only	*/
-#define CONFIG_ENV_OFFSET		0x00004000	/* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE		0x00002000	/* Total Size of Environment Sector */
-
-#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 512 kB for malloc()	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00004000	/* memtest works on		*/
-#define CONFIG_SYS_MEMTEST_END		0x01f00000	/* 0 ... 32 MB in DRAM		*/
-
-/*
- * Serial port configuration
- */
-
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-
-#define CONFIG_SYS_NS16550_CLK		1843200
-
-#define CONFIG_SYS_NS16550_COM1	0xff800008
-#define CONFIG_SYS_NS16550_COM2	0xff800000
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_CLK_FREQ  33333333	/* external frequency to pll */
-#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER  3
-
-#define CONFIG_SYS_EUMB_ADDR		0xFCE00000
-
-/* MCCR1 */
-#define CONFIG_SYS_ROMNAL		3	/* rom/flash next access time		*/
-#define CONFIG_SYS_ROMFAL		7	/* rom/flash access time		*/
-
-/* MCCR2 */
-#define CONFIG_SYS_ASRISE		6	/* ASRISE in clocks			*/
-#define CONFIG_SYS_ASFALL		12	/* ASFALL in clocks			*/
-#define CONFIG_SYS_REFINT		5600	/* REFINT in clocks			*/
-
-/* MCCR3 */
-#define CONFIG_SYS_BSTOPRE		0x3cf	/* Burst To Precharge			*/
-#define CONFIG_SYS_REFREC		2	/* Refresh to activate interval		*/
-#define CONFIG_SYS_RDLAT		3	/* data latency from read command	*/
-
-/* MCCR4 */
-#define CONFIG_SYS_PRETOACT		1	/* Precharge to activate interval	*/
-#define CONFIG_SYS_ACTTOPRE		3	/* Activate to Precharge interval	*/
-#define CONFIG_SYS_ACTORW		2	/* Activate to R/W			*/
-#define CONFIG_SYS_SDMODE_CAS_LAT	2	/* SDMODE CAS latency			*/
-#define CONFIG_SYS_SDMODE_WRAP		0	/* SDMODE Wrap type			*/
-#define CONFIG_SYS_SDMODE_BURSTLEN	2	/* SDMODE Burst length 2=4, 3=8		*/
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER   1
-
-/* Memory bank settings:
- *
- * only bits 20-29 are actually used from these vales to set the
- * start/qend address the upper two bits will be 0, and the lower 20
- * bits will be set to 0x00000 for a start address, or 0xfffff for an
- * end address
- */
-#define CONFIG_SYS_BANK0_START		0x00000000
-#define CONFIG_SYS_BANK0_END		(CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE	1
-#define CONFIG_SYS_BANK1_START		0x00000000
-#define CONFIG_SYS_BANK1_END		0x00000000
-#define CONFIG_SYS_BANK1_ENABLE	0
-#define CONFIG_SYS_BANK2_START		0x00000000
-#define CONFIG_SYS_BANK2_END		0x00000000
-#define CONFIG_SYS_BANK2_ENABLE	0
-#define CONFIG_SYS_BANK3_START		0x00000000
-#define CONFIG_SYS_BANK3_END		0x00000000
-#define CONFIG_SYS_BANK3_ENABLE	0
-#define CONFIG_SYS_BANK4_START		0x00000000
-#define CONFIG_SYS_BANK4_END		0x00000000
-#define CONFIG_SYS_BANK4_ENABLE	0
-#define CONFIG_SYS_BANK5_START		0x00000000
-#define CONFIG_SYS_BANK5_END		0x00000000
-#define CONFIG_SYS_BANK5_ENABLE	0
-#define CONFIG_SYS_BANK6_START		0x00000000
-#define CONFIG_SYS_BANK6_END		0x00000000
-#define CONFIG_SYS_BANK6_ENABLE	0
-#define CONFIG_SYS_BANK7_START		0x00000000
-#define CONFIG_SYS_BANK7_END		0x00000000
-#define CONFIG_SYS_BANK7_ENABLE	0
-
-/*
- * Memory bank enable bitmask, specifying which of the banks defined above
- * are actually present. MSB is for bank #7, LSB is for bank #0.
- */
-#define CONFIG_SYS_BANK_ENABLE		0x01
-
-#define CONFIG_SYS_ODCR		0xff	/* configures line driver impedances,	*/
-					/* see 8240 book for bit definitions	*/
-#define CONFIG_SYS_PGMAX		0x32	/* how long the 8240 retains the	*/
-					/* currently accessed page in memory	*/
-					/* see 8240 book for details		*/
-
-/* SDRAM 0 - 256MB */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-/* PCI memory space */
-#define CONFIG_SYS_IBAT2L	(0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U	(0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* Config addrs, etc */
-#define CONFIG_SYS_IBAT3L	(0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8240 CPU			*/
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-#endif	/* __CONFIG_H */