diff mbox

[U-Boot,v2,08/14] arm/km: redefine piggy 4 reg names to avoid conflicts

Message ID 1339594400-4848-9-git-send-email-holger.brunck@keymile.com
State Superseded
Headers show

Commit Message

Holger Brunck June 13, 2012, 1:33 p.m. UTC 
From: Valentin Longchamp <valentin.longchamp@keymile.com>

Some very similar #defines for reg addresses are used in a later patch
(managed_switch support for km_arm).

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
---
changes for v2:
  - nothing

 board/keymile/km_arm/km_arm.c |   22 +++++++++++-----------
 1 files changed, 11 insertions(+), 11 deletions(-)
diff mbox

Patch

diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index 5c9ba8f..d9cd4a0 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -332,13 +332,13 @@  void dram_init_banksize(void)
 
 #if (defined(CONFIG_KM_PIGGY4_88E6061))
 
-#define	PHY_LED_SEL	0x18
-#define PHY_LED0_LINK	(0x5)
-#define PHY_LED1_ACT	(0x8<<4)
-#define PHY_LED2_INT	(0xe<<8)
-#define	PHY_SPEC_CTRL	0x1c
+#define	PHY_LED_SEL_REG		0x18
+#define PHY_LED0_LINK		(0x5)
+#define PHY_LED1_ACT		(0x8<<4)
+#define PHY_LED2_INT		(0xe<<8)
+#define	PHY_SPEC_CTRL_REG	0x1c
 #define PHY_RGMII_CLK_STABLE	(0x1<<10)
-#define PHY_CLSA	(0x1<<1)
+#define PHY_CLSA		(0x1<<1)
 
 /* Configure and enable MV88E3018 PHY */
 void reset_phy(void)
@@ -350,15 +350,15 @@  void reset_phy(void)
 		return;
 
 	/* RGMII clk transition on data stable */
-	if (miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL, &reg) != 0)
+	if (!miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, &reg))
 		printf("Error reading PHY spec ctrl reg\n");
-	if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL,
-		reg | PHY_RGMII_CLK_STABLE | PHY_CLSA) != 0)
+	if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG,
+		reg | PHY_RGMII_CLK_STABLE | PHY_CLSA))
 		printf("Error writing PHY spec ctrl reg\n");
 
 	/* leds setup */
-	if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL,
-		PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT) != 0)
+	if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL_REG,
+		PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT))
 		printf("Error writing PHY LED reg\n");
 
 	/* reset the phy */