From patchwork Tue Jun 28 13:14:54 2011 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 8bit X-Patchwork-Submitter: =?utf-8?q?Andreas_Bie=C3=9Fmann?= X-Patchwork-Id: 102378 X-Patchwork-Delegate: info@emk-elektronik.de Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Received: from theia.denx.de (theia.denx.de [85.214.87.163]) by ozlabs.org (Postfix) with ESMTP id 5A554B6F5C for ; Tue, 28 Jun 2011 23:20:16 +1000 (EST) Received: from localhost (localhost [127.0.0.1]) by theia.denx.de (Postfix) with ESMTP id ADC75280E2; Tue, 28 Jun 2011 15:20:12 +0200 (CEST) X-Virus-Scanned: Debian amavisd-new at theia.denx.de Received: from theia.denx.de ([127.0.0.1]) by localhost (theia.denx.de [127.0.0.1]) (amavisd-new, port 10024) with ESMTP id mycl8G-KrJUg; Tue, 28 Jun 2011 15:20:12 +0200 (CEST) Received: from theia.denx.de (localhost [127.0.0.1]) by theia.denx.de (Postfix) with ESMTP id 3F57B280DA; Tue, 28 Jun 2011 15:20:10 +0200 (CEST) Received: from localhost (localhost [127.0.0.1]) by theia.denx.de (Postfix) with ESMTP id CBEE2280DA for ; Tue, 28 Jun 2011 15:20:07 +0200 (CEST) X-Virus-Scanned: Debian amavisd-new at theia.denx.de Received: from theia.denx.de ([127.0.0.1]) by localhost (theia.denx.de [127.0.0.1]) (amavisd-new, port 10024) with ESMTP id Jcq-czxZ14nZ for ; Tue, 28 Jun 2011 15:20:06 +0200 (CEST) X-Greylist: delayed 305 seconds by postgrey-1.27 at theia; Tue, 28 Jun 2011 15:20:04 CEST X-policyd-weight: NOT_IN_SBL_XBL_SPAMHAUS=-1.5 NOT_IN_SPAMCOP=-1.5 NOT_IN_BL_NJABL=-1.5 (only DNSBL check requested) Received: from moutng.kundenserver.de (moutng.kundenserver.de [212.227.126.187]) by theia.denx.de (Postfix) with ESMTP id 63823280D6 for ; Tue, 28 Jun 2011 15:20:04 +0200 (CEST) Received: from corscience.de (DSL01.212.114.252.242.ip-pool.NEFkom.net [212.114.252.242]) by mrelayeu.kundenserver.de (node=mreu3) with ESMTP (Nemesis) id 0Lsauz-1RYVPS3dQP-012Jba; Tue, 28 Jun 2011 15:14:56 +0200 Received: from azuregos.cs.local (unknown [192.168.102.9]) by corscience.de (Postfix) with ESMTP id 385D451F62; Tue, 28 Jun 2011 15:14:55 +0200 (CEST) From: =?UTF-8?q?Andreas=20Bie=C3=9Fmann?= To: u-boot@lists.denx.de Date: Tue, 28 Jun 2011 15:14:54 +0200 Message-Id: <1309266894-18594-1-git-send-email-biessmann@corscience.de> X-Mailer: git-send-email 1.7.2.5 MIME-Version: 1.0 X-Provags-ID: V02:K0:VzS4Jx1Y2wXFJMJ90a11hyyXcjMl+PQJcjeDaHgdXyC +NO7NMNrDMIE8ELLR3LtXPQe4bqOd4TojScKEclvQpP61t+L8x Hu6mQRb517mR/pTUwB251VDsf+Pbfg6BWpZL//e7xSAVhTRHX0 Irxy4Ic/8QuQvnDBj+Q4Epx35Lq+J3tX8n9KG8KB/T9INsiBHt cOGTzP09W10dgbNHKMnnQ== Cc: =?UTF-8?q?Andreas=20Bie=C3=9Fmann?= Subject: [U-Boot] [PATCH] avr32: add grasshopper (ICnova AP7000) board X-BeenThere: u-boot@lists.denx.de X-Mailman-Version: 2.1.9 Precedence: list List-Id: U-Boot discussion List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Sender: u-boot-bounces@lists.denx.de Errors-To: u-boot-bounces@lists.denx.de The grasshopper board is a neat avr32 evaluation kit produced by In-Circuit GmbH. See http://www.ic-board.de/product_info.php?info=p75_ICnova-AP7000-Base.html for detailed information about this device. Signed-off-by: Andreas Bießmann --- board/in-circuit/grasshopper/Makefile | 45 +++++++ board/in-circuit/grasshopper/grasshopper.c | 105 +++++++++++++++ boards.cfg | 1 + include/configs/grasshopper.h | 197 ++++++++++++++++++++++++++++ 4 files changed, 348 insertions(+), 0 deletions(-) create mode 100644 board/in-circuit/grasshopper/Makefile create mode 100644 board/in-circuit/grasshopper/grasshopper.c create mode 100644 include/configs/grasshopper.h diff --git a/board/in-circuit/grasshopper/Makefile b/board/in-circuit/grasshopper/Makefile new file mode 100644 index 0000000..a6c36c7 --- /dev/null +++ b/board/in-circuit/grasshopper/Makefile @@ -0,0 +1,45 @@ +# +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# Copyright (C) 2011 +# Corscience GmbH & Co.KG, Andreas Bießmann +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA + +include $(TOPDIR)/config.mk + +LIB := $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o + +SRCS := $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/in-circuit/grasshopper/grasshopper.c b/board/in-circuit/grasshopper/grasshopper.c new file mode 100644 index 0000000..d020c29 --- /dev/null +++ b/board/in-circuit/grasshopper/grasshopper.c @@ -0,0 +1,105 @@ +/* + * Copyright (C) 2011 + * Corscience GmbH & Co.KG, Andreas Bießmann + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include + +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = { + { + .virt_pgno = CONFIG_SYS_FLASH_BASE >> PAGE_SHIFT, + .nr_pages = CONFIG_SYS_FLASH_SIZE >> PAGE_SHIFT, + .phys = (CONFIG_SYS_FLASH_BASE >> PAGE_SHIFT) + | MMU_VMR_CACHE_NONE, + }, { + .virt_pgno = CONFIG_SYS_SDRAM_BASE >> PAGE_SHIFT, + .nr_pages = EBI_SDRAM_SIZE >> PAGE_SHIFT, + .phys = (CONFIG_SYS_SDRAM_BASE >> PAGE_SHIFT) + | MMU_VMR_CACHE_WRBACK, + }, +}; + +static const struct sdram_config sdram_config = { + /* Dual MT48LC16M16A2-7E (or equal) */ + .data_bits = SDRAM_DATA_32BIT, + .row_bits = 13, + .col_bits = 9, + .bank_bits = 2, + .cas = 2, + .twr = 2, + .trc = 7, + .trp = 2, + .trcd = 2, + .tras = 4, + .txsr = 7, + /* 7.81 us */ + .refresh_period = (781 * (SDRAMC_BUS_HZ / 1000)) / 100000, +}; + +int board_early_init_f(void) +{ + /* Enable SDRAM in the EBI mux */ + hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE)); + + portmux_enable_ebi(SDRAM_DATA_32BIT, 23, 0, PORTMUX_DRIVE_HIGH); + portmux_enable_usart0(PORTMUX_DRIVE_MIN); + portmux_enable_usart1(PORTMUX_DRIVE_MIN); +#if defined(CONFIG_MACB) + portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_LOW); +#endif + + return 0; +} + +phys_size_t initdram(int board_type) +{ + unsigned long expected_size; + unsigned long actual_size; + void *sdram_base; + + sdram_base = uncached(EBI_SDRAM_BASE); + + expected_size = sdram_init(sdram_base, &sdram_config); + actual_size = get_ram_size(sdram_base, expected_size); + + if (expected_size != actual_size) + printf("Warning: Only %lu of %lu MiB SDRAM is working\n", + actual_size >> 20, expected_size >> 20); + + return actual_size; +} + +#ifdef CONFIG_CMD_NET +int board_eth_init(bd_t *bi) +{ + macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0, bi->bi_phy_id[0]); + return 0; +} +#endif diff --git a/boards.cfg b/boards.cfg index dfefc3f..839441a 100644 --- a/boards.cfg +++ b/boards.cfg @@ -209,6 +209,7 @@ atstk1003 avr32 at32ap atstk1000 atmel atstk1004 avr32 at32ap atstk1000 atmel at32ap700x atstk1006 avr32 at32ap atstk1000 atmel at32ap700x favr-32-ezkit avr32 at32ap - earthlcd at32ap700x +grasshopper avr32 at32ap - in-circuit at32ap700x mimc200 avr32 at32ap - mimc at32ap700x hammerhead avr32 at32ap - miromico at32ap700x bct-brettl2 blackfin blackfin diff --git a/include/configs/grasshopper.h b/include/configs/grasshopper.h new file mode 100644 index 0000000..989d506 --- /dev/null +++ b/include/configs/grasshopper.h @@ -0,0 +1,197 @@ +/* + * Copyright (C) 2011 + * Corscience GmbH & Co.KG, Andreas Bießmann + * + * Configuration settings for the grasshopper (ICnova AP7000) board + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __GRASSHOPPER_CONFIG_H +#define __GRASSHOPPER_CONFIG_H + +#include + +#define CONFIG_AVR32 +#define CONFIG_AT32AP +#define CONFIG_AT32AP7000 + +/* + * Timer clock frequency. We're using the CPU-internal COUNT register + * for this, so this is equivalent to the CPU core clock frequency + */ +#define CONFIG_SYS_HZ 1000 + +/* + * Set up the PLL to run at 140 MHz, the CPU to run at the PLL + * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the + * PLL frequency. + * (CONFIG_SYS_OSC0_HZ * CONFIG_SYS_PLL0_MUL) / CONFIG_SYS_PLL0_DIV = PLL MHz + */ +#define CONFIG_PLL +#define CONFIG_SYS_POWER_MANAGER +#define CONFIG_SYS_OSC0_HZ 20000000 +#define CONFIG_SYS_PLL0_DIV 1 +#define CONFIG_SYS_PLL0_MUL 7 +#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16 +/* + * Set the CPU running at: + * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz + */ +#define CONFIG_SYS_CLKDIV_CPU 0 +/* + * Set the HSB running at: + * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz + */ +#define CONFIG_SYS_CLKDIV_HSB 1 +/* + * Set the PBA running at: + * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz + */ +#define CONFIG_SYS_CLKDIV_PBA 2 +/* + * Set the PBB running at: + * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz + */ +#define CONFIG_SYS_CLKDIV_PBB 1 + +/* Reserve VM regions for SDRAM and NOR flash */ +#define CONFIG_SYS_NR_VM_REGIONS 2 + +/* + * The PLLOPT register controls the PLL like this: + * icp = PLLOPT<2> + * ivco = PLLOPT<1:0> + * + * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz). + */ +#define CONFIG_SYS_PLL0_OPT 0x04 + +#define CONFIG_USART_BASE ATMEL_BASE_USART1 +#define CONFIG_USART_ID 1 + +/* User serviceable stuff */ +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG + +#define CONFIG_STACKSIZE (2048) + +#define CONFIG_BAUDRATE 115200 + +/* + * Only interrupt autoboot if is pressed. Otherwise, garbage + * data on the serial line may interrupt the boot sequence. + */ +#define CONFIG_BOOTDELAY 1 +#define CONFIG_AUTOBOOT +#define CONFIG_AUTOBOOT_KEYED +#define CONFIG_AUTOBOOT_PROMPT \ + "Press SPACE to abort autoboot in %d seconds\n", bootdelay +#define CONFIG_AUTOBOOT_DELAY_STR "d" +#define CONFIG_AUTOBOOT_STOP_STR " " + +/* + * After booting the board for the first time, new ethernet addresses + * should be generated and assigned to the environment variables + * "ethaddr". This is normally done during production. + */ +#define CONFIG_OVERWRITE_ETHADDR_ONCE +#define CONFIG_NET_MULTI + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY + +/* + * Command line configuration. + */ +#include + +/* remove unneeded commands */ +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_SETGETDCR + +/* add useful commands */ +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_PROMPT_HUSH_PS2 "~> " +#define CONFIG_CMDLINE_EDITING + +#define CONFIG_ATMEL_USART +#define CONFIG_MACB +#define CONFIG_PORTMUX_PIO +#define CONFIG_SYS_NR_PIOS 5 +#define CONFIG_SYS_HSDRAMC + +#define CONFIG_SYS_DCACHE_LINESZ 32 +#define CONFIG_SYS_ICACHE_LINESZ 32 + +#define CONFIG_NR_DRAM_BANKS 1 + +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER + +#define CONFIG_SYS_FLASH_BASE 0x00000000 +#define CONFIG_SYS_FLASH_SIZE 0x800000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 135 + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_TEXT_BASE 0x00000000 + +#define CONFIG_SYS_INTRAM_BASE INTERNAL_SRAM_BASE +#define CONFIG_SYS_INTRAM_SIZE INTERNAL_SRAM_SIZE +#define CONFIG_SYS_SDRAM_BASE EBI_SDRAM_BASE + +#define CONFIG_ENV_IS_IN_FLASH +/* place u-boot env in flash sector after u-boot */ +#define CONFIG_ENV_SIZE 0x10000 +#define CONFIG_ENV_ADDR 0x20000 + +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + \ + CONFIG_SYS_INTRAM_SIZE) + +#define CONFIG_SYS_MALLOC_LEN (256*1024) +#define CONFIG_SYS_DMA_ALLOC_LEN (16384) + +/* Allow 4MB for the kernel run-time image */ +#define CONFIG_SYS_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) +#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024) + +/* Other configuration settings that shouldn't have to change all that often */ +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LONGHELP + +#define CONFIG_SYS_MEMTEST_START EBI_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x700000) +#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } + +#endif /* __GRASSHOPPER_CONFIG_H */