@@ -52,6 +52,19 @@ ENTRY(_start)
sp.l = LO(L1_SRAM_SCRATCH_END - 20);
sp.h = HI(L1_SRAM_SCRATCH_END - 20);
+ /* Optimization register tricks: keep a base value in the
+ * reserved P registers so we use the load/store with an
+ * offset syntax. R0 = [P5 + <constant>];
+ * P4 - system MMR base
+ * P5 - core MMR base
+ */
+#ifdef CONFIG_HW_WATCHDOG
+ p4.l = 0;
+ p4.h = HI(SYSMMR_BASE);
+#endif
+ p5.l = 0;
+ p5.h = HI(COREMMR_BASE);
+
#ifdef CONFIG_HW_WATCHDOG
# ifndef CONFIG_HW_WATCHDOG_TIMEOUT_START
# define CONFIG_HW_WATCHDOG_TIMEOUT_START 5000
@@ -60,13 +73,11 @@ ENTRY(_start)
* That should be long enough to bootstrap ourselves up and
* then the common u-boot code can take over.
*/
- P0.L = LO(WDOG_CNT);
- P0.H = HI(WDOG_CNT);
- R0.L = 0;
- R0.H = HI(MSEC_TO_SCLK(CONFIG_HW_WATCHDOG_TIMEOUT_START));
- [P0] = R0;
+ r0 = 0;
+ r0.h = HI(MSEC_TO_SCLK(CONFIG_HW_WATCHDOG_TIMEOUT_START));
+ [p4 + (WDOG_CNT - SYSMMR_BASE)] = r0;
/* fire up the watchdog - R0.L above needs to be 0x0000 */
- W[P0 + (WDOG_CTL - WDOG_CNT)] = R0;
+ W[p4 + (WDOG_CTL - SYSMMR_BASE)] = r0;
#endif
/* Turn on the serial for debugging the init process */
@@ -121,6 +132,18 @@ ENTRY(_start)
if cc jump .Lnorelocate;
r6 = 0 (x);
+ /* Turn off caches as they require CPLBs and a CPLB miss requires
+ * a software exception handler to process it. But we're about to
+ * clobber any previous executing software (like U-Boot that just
+ * launched a new U-Boot via 'go'), so any handler state will be
+ * unreliable after the memcpy below.
+ */
+ serial_early_puts("Kill Caches");
+ r0 = 0;
+ [p5 + (IMEM_CONTROL - COREMMR_BASE)] = r0;
+ [p5 + (DMEM_CONTROL - COREMMR_BASE)] = r0;
+ ssync;
+
/* In bypass mode, we don't have an LDR with an init block
* so we need to explicitly call it ourselves. This will
* reprogram our clocks, memory, and setup our async banks.
@@ -204,17 +227,15 @@ ENTRY(_start)
serial_early_puts("Lower to 15");
r0 = r7;
r1 = r6;
- p0.l = LO(EVT15);
- p0.h = HI(EVT15);
p1.l = .Lenable_nested;
p1.h = .Lenable_nested;
- [p0] = p1;
+ [p5 + (EVT15 - COREMMR_BASE)] = p1;
r7 = EVT_IVG15 (z);
sti r7;
raise 15;
- p4.l = .LWAIT_HERE;
- p4.h = .LWAIT_HERE;
- reti = p4;
+ p3.l = .LWAIT_HERE;
+ p3.h = .LWAIT_HERE;
+ reti = p3;
rti;
/* Enable nested interrupts before continuing with cpu init */
When bootstrapping ourselves on the fly at runtime (via "go"), we need to turn off the caches to avoid taking software exceptions. Since caches need CPLBs and CPLBs need exception handlers, but we're about to rewrite the code in memory where those exception handlers live, we need to turn off caches first. This new code also encourages a slight code optimization by storing the MMR bases in dedicated registers so we don't have to fully load up the pointer regs multiple times. Signed-off-by: Mike Frysinger <vapier@gentoo.org> --- arch/blackfin/cpu/start.S | 45 +++++++++++++++++++++++++++++++++------------ 1 files changed, 33 insertions(+), 12 deletions(-)