diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 5182a3d5660c..838bbfcf11ea 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -194,6 +194,18 @@ config REGULATOR_BD70528
 	  This driver can also be built as a module. If so, the module
 	  will be called bd70528-regulator.
 
+config REGULATOR_BD71828
+	tristate "ROHM BD71828 Power Regulator"
+	depends on MFD_ROHM_BD71828
+	select REGULATOR_ROHM
+	help
+	  This driver supports voltage regulators on ROHM BD71828 PMIC.
+	  This will enable support for the software controllable buck
+	  and LDO regulators.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called bd71828-regulator.
+
 config REGULATOR_BD718XX
 	tristate "ROHM BD71837 Power Regulator"
 	depends on MFD_ROHM_BD718XX
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 6bcab72c1fc7..cf0e08c5f3cd 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o
 obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o
 obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
 obj-$(CONFIG_REGULATOR_BD70528) += bd70528-regulator.o
+obj-$(CONFIG_REGULATOR_BD71828) += bd71828-regulator.o
 obj-$(CONFIG_REGULATOR_BD718XX) += bd718x7-regulator.o
 obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
 obj-$(CONFIG_REGULATOR_DA903X)	+= da903x.o
diff --git a/drivers/regulator/bd71828-regulator.c b/drivers/regulator/bd71828-regulator.c
new file mode 100644
index 000000000000..3f46658280be
--- /dev/null
+++ b/drivers/regulator/bd71828-regulator.c
@@ -0,0 +1,833 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2019 ROHM Semiconductors
+// bd71828-regulator.c ROHM BD71828GW-DS1 regulator driver
+//
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/rohm-bd71828.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+
+struct reg_init {
+	unsigned int reg;
+	unsigned int mask;
+	unsigned int val;
+};
+struct bd71828_regulator_data {
+	struct regulator_desc desc;
+	const struct rohm_dvs_config dvs;
+	const struct reg_init *reg_inits;
+	int reg_init_amnt;
+};
+
+static const struct reg_init buck1_inits[] = {
+	/*
+	 * DVS Buck voltages can be changed by register values or via GPIO.
+	 * Use register accesses by default.
+	 */
+	{
+		.reg = BD71828_REG_PS_CTRL_1,
+		.mask = BD71828_MASK_DVS_BUCK1_CTRL,
+		.val = BD71828_DVS_BUCK1_CTRL_I2C,
+	},
+};
+
+static const struct reg_init buck2_inits[] = {
+	{
+		.reg = BD71828_REG_PS_CTRL_1,
+		.mask = BD71828_MASK_DVS_BUCK2_CTRL,
+		.val = BD71828_DVS_BUCK2_CTRL_I2C,
+	},
+};
+
+static const struct reg_init buck6_inits[] = {
+	{
+		.reg = BD71828_REG_PS_CTRL_1,
+		.mask = BD71828_MASK_DVS_BUCK6_CTRL,
+		.val = BD71828_DVS_BUCK6_CTRL_I2C,
+	},
+};
+
+static const struct reg_init buck7_inits[] = {
+	{
+		.reg = BD71828_REG_PS_CTRL_1,
+		.mask = BD71828_MASK_DVS_BUCK7_CTRL,
+		.val = BD71828_DVS_BUCK7_CTRL_I2C,
+	},
+};
+
+static const struct regulator_linear_range bd71828_buck1267_volts[] = {
+	REGULATOR_LINEAR_RANGE(500000, 0x00, 0xef, 6250),
+	REGULATOR_LINEAR_RANGE(2000000, 0xf0, 0xff, 0),
+};
+
+static const struct regulator_linear_range bd71828_buck3_volts[] = {
+	REGULATOR_LINEAR_RANGE(1200000, 0x00, 0x0f, 50000),
+	REGULATOR_LINEAR_RANGE(2000000, 0x10, 0x1f, 0),
+};
+
+static const struct regulator_linear_range bd71828_buck4_volts[] = {
+	REGULATOR_LINEAR_RANGE(1000000, 0x00, 0x1f, 25000),
+	REGULATOR_LINEAR_RANGE(1800000, 0x20, 0x3f, 0),
+};
+
+static const struct regulator_linear_range bd71828_buck5_volts[] = {
+	REGULATOR_LINEAR_RANGE(2500000, 0x00, 0x0f, 50000),
+	REGULATOR_LINEAR_RANGE(3300000, 0x10, 0x1f, 0),
+};
+
+static const struct regulator_linear_range bd71828_ldo_volts[] = {
+	REGULATOR_LINEAR_RANGE(800000, 0x00, 0x31, 50000),
+	REGULATOR_LINEAR_RANGE(3300000, 0x32, 0x3f, 0),
+};
+
+static int ramp_delay_supported(struct regulator_dev *rdev)
+{
+	switch (rdev->desc->id) {
+	case BD71828_BUCK1:
+	case BD71828_BUCK2:
+	case BD71828_BUCK6:
+	case BD71828_BUCK7:
+		return 1;
+	default:
+		break;
+	}
+	return 0;
+}
+
+static int bd71828_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
+{
+	unsigned int val;
+
+	if (!ramp_delay_supported(rdev)) {
+		dev_err(&rdev->dev, "%s: can't set ramp-delay\n",
+			rdev->desc->name);
+		return -EINVAL;
+	}
+
+	switch (ramp_delay) {
+	case 1 ... 2500:
+		val = 0;
+		break;
+	case 2501 ... 5000:
+		val = 1;
+		break;
+	case 5001 ... 10000:
+		val = 2;
+		break;
+	case 10001 ... 20000:
+		val = 3;
+		break;
+	default:
+		val = 3;
+		dev_err(&rdev->dev,
+			"ramp_delay: %d not supported, setting 20mV/uS",
+			 ramp_delay);
+	}
+
+	/*
+	 * On BD71828 the ramp delay level control reg is at offset +2 to
+	 * enable reg
+	 */
+	return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg + 2,
+				  BD71828_MASK_RAMP_DELAY,
+				  val << (ffs(BD71828_MASK_RAMP_DELAY) - 1));
+
+}
+
+static int buck_set_hw_dvs_levels(struct device_node *np,
+				  const struct regulator_desc *desc,
+				  struct regulator_config *cfg)
+{
+	struct bd71828_regulator_data *data;
+
+	data = container_of(desc, struct bd71828_regulator_data, desc);
+
+	return rohm_regulator_set_dvs_levels(&data->dvs, np, desc, cfg->regmap);
+}
+
+static int ldo6_parse_dt(struct device_node *np,
+			 const struct regulator_desc *desc,
+			 struct regulator_config *cfg)
+{
+	int ret, i;
+	uint32_t uv = 0;
+	unsigned int en;
+	struct regmap *regmap = cfg->regmap;
+	static const char * const props[] = { "rohm,dvs-run-voltage",
+					      "rohm,dvs-idle-voltage",
+					      "rohm,dvs-suspend-voltage",
+					      "rohm,dvs-lpsr-voltage" };
+	unsigned int mask[] = { BD71828_MASK_RUN_EN, BD71828_MASK_IDLE_EN,
+			       BD71828_MASK_SUSP_EN, BD71828_MASK_LPSR_EN };
+
+	for (i = 0; i < ARRAY_SIZE(props); i++) {
+		ret = of_property_read_u32(np, props[i], &uv);
+		if (ret) {
+			if (ret != -EINVAL)
+				return ret;
+			continue;
+		}
+		if (uv)
+			en = 0xffffffff;
+		else
+			en = 0;
+
+		ret = regmap_update_bits(regmap, desc->enable_reg, mask[i], en);
+		if (ret)
+			return ret;
+	}
+	return 0;
+}
+
+static const struct regulator_ops bd71828_buck_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static const struct regulator_ops bd71828_dvs_buck_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.set_ramp_delay = bd71828_set_ramp_delay,
+};
+
+static const struct regulator_ops bd71828_ldo_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static int bd71828_ldo6_get_voltage(struct regulator_dev *rdev)
+{
+	return BD71828_LDO_6_VOLTAGE;
+}
+
+static const struct regulator_ops bd71828_ldo6_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.get_voltage = bd71828_ldo6_get_voltage,
+	.is_enabled = regulator_is_enabled_regmap,
+};
+
+static const struct bd71828_regulator_data bd71828_rdata[] = {
+	{
+		.desc = {
+			.name = "buck1",
+			.of_match = of_match_ptr("BUCK1"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK1,
+			.ops = &bd71828_dvs_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck1267_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck1267_volts),
+			.n_voltages = BD71828_BUCK1267_VOLTS,
+			.enable_reg = BD71828_REG_BUCK1_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK1_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK1267_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK1_VOLT,
+			.run_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_reg = BD71828_REG_BUCK1_IDLE_VOLT,
+			.idle_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_reg = BD71828_REG_BUCK1_SUSP_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK1267_VOLT,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+			/*
+			 * LPSR voltage is same as SUSPEND voltage. Allow
+			 * setting it so that regulator can be set enabled at
+			 * LPSR state
+			 */
+			.lpsr_reg = BD71828_REG_BUCK1_SUSP_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK1267_VOLT,
+		},
+		.reg_inits = buck1_inits,
+		.reg_init_amnt = ARRAY_SIZE(buck1_inits),
+	},
+	{
+		.desc = {
+			.name = "buck2",
+			.of_match = of_match_ptr("BUCK2"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK2,
+			.ops = &bd71828_dvs_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck1267_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck1267_volts),
+			.n_voltages = BD71828_BUCK1267_VOLTS,
+			.enable_reg = BD71828_REG_BUCK2_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK2_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK1267_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK2_VOLT,
+			.run_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_reg = BD71828_REG_BUCK2_IDLE_VOLT,
+			.idle_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_reg = BD71828_REG_BUCK2_SUSP_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK1267_VOLT,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+			.lpsr_reg = BD71828_REG_BUCK2_SUSP_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK1267_VOLT,
+		},
+		.reg_inits = buck2_inits,
+		.reg_init_amnt = ARRAY_SIZE(buck2_inits),
+	},
+	{
+		.desc = {
+			.name = "buck3",
+			.of_match = of_match_ptr("BUCK3"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK3,
+			.ops = &bd71828_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck3_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck3_volts),
+			.n_voltages = BD71828_BUCK3_VOLTS,
+			.enable_reg = BD71828_REG_BUCK3_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK3_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK3_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * BUCK3 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK3_VOLT,
+			.idle_reg = BD71828_REG_BUCK3_VOLT,
+			.suspend_reg = BD71828_REG_BUCK3_VOLT,
+			.lpsr_reg = BD71828_REG_BUCK3_VOLT,
+			.run_mask = BD71828_MASK_BUCK3_VOLT,
+			.idle_mask = BD71828_MASK_BUCK3_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK3_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK3_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+	},
+	{
+		.desc = {
+			.name = "buck4",
+			.of_match = of_match_ptr("BUCK4"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK4,
+			.ops = &bd71828_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck4_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck4_volts),
+			.n_voltages = BD71828_BUCK4_VOLTS,
+			.enable_reg = BD71828_REG_BUCK4_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK4_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK4_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * BUCK4 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK4_VOLT,
+			.idle_reg = BD71828_REG_BUCK4_VOLT,
+			.suspend_reg = BD71828_REG_BUCK4_VOLT,
+			.lpsr_reg = BD71828_REG_BUCK4_VOLT,
+			.run_mask = BD71828_MASK_BUCK4_VOLT,
+			.idle_mask = BD71828_MASK_BUCK4_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK4_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK4_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+	},
+	{
+		.desc = {
+			.name = "buck5",
+			.of_match = of_match_ptr("BUCK5"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK5,
+			.ops = &bd71828_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck5_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck5_volts),
+			.n_voltages = BD71828_BUCK5_VOLTS,
+			.enable_reg = BD71828_REG_BUCK5_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK5_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK5_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * BUCK5 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK5_VOLT,
+			.idle_reg = BD71828_REG_BUCK5_VOLT,
+			.suspend_reg = BD71828_REG_BUCK5_VOLT,
+			.lpsr_reg = BD71828_REG_BUCK5_VOLT,
+			.run_mask = BD71828_MASK_BUCK5_VOLT,
+			.idle_mask = BD71828_MASK_BUCK5_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK5_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK5_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+	},
+	{
+		.desc = {
+			.name = "buck6",
+			.of_match = of_match_ptr("BUCK6"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK6,
+			.ops = &bd71828_dvs_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck1267_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck1267_volts),
+			.n_voltages = BD71828_BUCK1267_VOLTS,
+			.enable_reg = BD71828_REG_BUCK6_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK6_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK1267_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK6_VOLT,
+			.run_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_reg = BD71828_REG_BUCK6_IDLE_VOLT,
+			.idle_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_reg = BD71828_REG_BUCK6_SUSP_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK1267_VOLT,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+			.lpsr_reg = BD71828_REG_BUCK6_SUSP_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK1267_VOLT,
+		},
+		.reg_inits = buck6_inits,
+		.reg_init_amnt = ARRAY_SIZE(buck6_inits),
+	},
+	{
+		.desc = {
+			.name = "buck7",
+			.of_match = of_match_ptr("BUCK7"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK7,
+			.ops = &bd71828_dvs_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck1267_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck1267_volts),
+			.n_voltages = BD71828_BUCK1267_VOLTS,
+			.enable_reg = BD71828_REG_BUCK7_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK7_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK1267_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK7_VOLT,
+			.run_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_reg = BD71828_REG_BUCK7_IDLE_VOLT,
+			.idle_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_reg = BD71828_REG_BUCK7_SUSP_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK1267_VOLT,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+			.lpsr_reg = BD71828_REG_BUCK7_SUSP_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK1267_VOLT,
+		},
+		.reg_inits = buck7_inits,
+		.reg_init_amnt = ARRAY_SIZE(buck7_inits),
+	},
+	{
+		.desc = {
+			.name = "ldo1",
+			.of_match = of_match_ptr("LDO1"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO1,
+			.ops = &bd71828_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_ldo_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_ldo_volts),
+			.n_voltages = BD71828_LDO_VOLTS,
+			.enable_reg = BD71828_REG_LDO1_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_LDO1_VOLT,
+			.vsel_mask = BD71828_MASK_LDO_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * LDO1 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_LDO1_VOLT,
+			.idle_reg = BD71828_REG_LDO1_VOLT,
+			.suspend_reg = BD71828_REG_LDO1_VOLT,
+			.lpsr_reg = BD71828_REG_LDO1_VOLT,
+			.run_mask = BD71828_MASK_LDO_VOLT,
+			.idle_mask = BD71828_MASK_LDO_VOLT,
+			.suspend_mask = BD71828_MASK_LDO_VOLT,
+			.lpsr_mask = BD71828_MASK_LDO_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+	}, {
+		.desc = {
+			.name = "ldo2",
+			.of_match = of_match_ptr("LDO2"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO2,
+			.ops = &bd71828_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_ldo_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_ldo_volts),
+			.n_voltages = BD71828_LDO_VOLTS,
+			.enable_reg = BD71828_REG_LDO2_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_LDO2_VOLT,
+			.vsel_mask = BD71828_MASK_LDO_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * LDO2 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_LDO2_VOLT,
+			.idle_reg = BD71828_REG_LDO2_VOLT,
+			.suspend_reg = BD71828_REG_LDO2_VOLT,
+			.lpsr_reg = BD71828_REG_LDO2_VOLT,
+			.run_mask = BD71828_MASK_LDO_VOLT,
+			.idle_mask = BD71828_MASK_LDO_VOLT,
+			.suspend_mask = BD71828_MASK_LDO_VOLT,
+			.lpsr_mask = BD71828_MASK_LDO_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+	}, {
+		.desc = {
+			.name = "ldo3",
+			.of_match = of_match_ptr("LDO3"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO3,
+			.ops = &bd71828_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_ldo_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_ldo_volts),
+			.n_voltages = BD71828_LDO_VOLTS,
+			.enable_reg = BD71828_REG_LDO3_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_LDO3_VOLT,
+			.vsel_mask = BD71828_MASK_LDO_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * LDO3 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_LDO3_VOLT,
+			.idle_reg = BD71828_REG_LDO3_VOLT,
+			.suspend_reg = BD71828_REG_LDO3_VOLT,
+			.lpsr_reg = BD71828_REG_LDO3_VOLT,
+			.run_mask = BD71828_MASK_LDO_VOLT,
+			.idle_mask = BD71828_MASK_LDO_VOLT,
+			.suspend_mask = BD71828_MASK_LDO_VOLT,
+			.lpsr_mask = BD71828_MASK_LDO_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+
+	}, {
+		.desc = {
+			.name = "ldo4",
+			.of_match = of_match_ptr("LDO4"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO4,
+			.ops = &bd71828_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_ldo_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_ldo_volts),
+			.n_voltages = BD71828_LDO_VOLTS,
+			.enable_reg = BD71828_REG_LDO4_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_LDO4_VOLT,
+			.vsel_mask = BD71828_MASK_LDO_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * LDO1 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_LDO4_VOLT,
+			.idle_reg = BD71828_REG_LDO4_VOLT,
+			.suspend_reg = BD71828_REG_LDO4_VOLT,
+			.lpsr_reg = BD71828_REG_LDO4_VOLT,
+			.run_mask = BD71828_MASK_LDO_VOLT,
+			.idle_mask = BD71828_MASK_LDO_VOLT,
+			.suspend_mask = BD71828_MASK_LDO_VOLT,
+			.lpsr_mask = BD71828_MASK_LDO_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+	}, {
+		.desc = {
+			.name = "ldo5",
+			.of_match = of_match_ptr("LDO5"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO5,
+			.ops = &bd71828_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_ldo_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_ldo_volts),
+			.n_voltages = BD71828_LDO_VOLTS,
+			.enable_reg = BD71828_REG_LDO5_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_LDO5_VOLT,
+			.vsel_mask = BD71828_MASK_LDO_VOLT,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+			.owner = THIS_MODULE,
+		},
+		/*
+		 * LDO5 is special. It can choose vsel settings to be configured
+		 * from 2 different registers (by GPIO).
+		 *
+		 * This driver supports only configuration where
+		 * BD71828_REG_LDO5_VOLT_L is used.
+		 */
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_LDO5_VOLT,
+			.idle_reg = BD71828_REG_LDO5_VOLT,
+			.suspend_reg = BD71828_REG_LDO5_VOLT,
+			.lpsr_reg = BD71828_REG_LDO5_VOLT,
+			.run_mask = BD71828_MASK_LDO_VOLT,
+			.idle_mask = BD71828_MASK_LDO_VOLT,
+			.suspend_mask = BD71828_MASK_LDO_VOLT,
+			.lpsr_mask = BD71828_MASK_LDO_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+
+	}, {
+		.desc = {
+			.name = "ldo6",
+			.of_match = of_match_ptr("LDO6"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO6,
+			.ops = &bd71828_ldo6_ops,
+			.type = REGULATOR_VOLTAGE,
+			.n_voltages = 1,
+			.enable_reg = BD71828_REG_LDO6_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.owner = THIS_MODULE,
+			/*
+			 * LDO6 only supports enable/disable for all states.
+			 * Voltage for LDO6 is fixed.
+			 */
+			.of_parse_cb = ldo6_parse_dt,
+		},
+	}, {
+		.desc = {
+			/* SNVS LDO in data-sheet */
+			.name = "ldo7",
+			.of_match = of_match_ptr("LDO7"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO_SNVS,
+			.ops = &bd71828_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_ldo_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_ldo_volts),
+			.n_voltages = BD71828_LDO_VOLTS,
+			.enable_reg = BD71828_REG_LDO7_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_LDO7_VOLT,
+			.vsel_mask = BD71828_MASK_LDO_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * LDO7 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_LDO7_VOLT,
+			.idle_reg = BD71828_REG_LDO7_VOLT,
+			.suspend_reg = BD71828_REG_LDO7_VOLT,
+			.lpsr_reg = BD71828_REG_LDO7_VOLT,
+			.run_mask = BD71828_MASK_LDO_VOLT,
+			.idle_mask = BD71828_MASK_LDO_VOLT,
+			.suspend_mask = BD71828_MASK_LDO_VOLT,
+			.lpsr_mask = BD71828_MASK_LDO_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+
+	},
+};
+
+static int bd71828_probe(struct platform_device *pdev)
+{
+	struct rohm_regmap_dev *bd71828;
+	int i, j, ret;
+	struct regulator_config config = {
+		.dev = pdev->dev.parent,
+	};
+
+	bd71828 = dev_get_drvdata(pdev->dev.parent);
+	if (!bd71828) {
+		dev_err(&pdev->dev, "No MFD driver data\n");
+		return -EINVAL;
+	}
+
+	config.regmap = bd71828->regmap;
+
+	for (i = 0; i < ARRAY_SIZE(bd71828_rdata); i++) {
+		struct regulator_dev *rdev;
+		const struct bd71828_regulator_data *rd;
+
+		rd = &bd71828_rdata[i];
+		rdev = devm_regulator_register(&pdev->dev,
+					       &rd->desc, &config);
+		if (IS_ERR(rdev)) {
+			dev_err(&pdev->dev,
+				"failed to register %s regulator\n",
+				rd->desc.name);
+			return PTR_ERR(rdev);
+		}
+		for (j = 0; j < rd->reg_init_amnt; j++) {
+			ret = regmap_update_bits(bd71828->regmap,
+						 rd->reg_inits[j].reg,
+						 rd->reg_inits[j].mask,
+						 rd->reg_inits[j].val);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"regulator %s init failed\n",
+					rd->desc.name);
+				return ret;
+			}
+		}
+	}
+	return 0;
+}
+
+static struct platform_driver bd71828_regulator = {
+	.driver = {
+		.name = "bd71828-pmic"
+	},
+	.probe = bd71828_probe,
+};
+
+module_platform_driver(bd71828_regulator);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD71828 voltage regulator driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:bd71828-pmic");
