diff --git a/content.tex b/content.tex
index dcf6c71..2fd1686 100644
--- a/content.tex
+++ b/content.tex
@@ -1770,7 +1770,8 @@ \subsection{MMIO Device Register Layout}\label{sec:Virtio Transport Options / Vi
   \hline
   \mmioreg{MsiState}{MSI state}{0x0c4}{R}{%
     When VIRTIO_F_MMIO_MSI has been negotiated, reading
-    from this register returns the global MSI enable/disable status.
+    from this register returns the global MSI enable/disable status
+    and whether device uses MSI sharing mode.
     \lstinputlisting{msi-state.c}
   }
   \hline
@@ -1926,12 +1927,18 @@ \subsubsection{Device Initialization}\label{sec:Virtio Transport Options / Virti
 mask and unmask the MSI vector applying to the one selected by writing
 to \field{MsiVecSel}.
 
+VIRTIO_MMIO_MSI_CMD_MAP_CONFIG command is to set the configuration event and MSI vector
+mapping. VIRTIO_MMIO_MSI_CMD_MAP_QUEUE is to set the queue event and MSI vector
+mapping. They SHOULD only be used in MSI sharing mode.
+
 \begin{lstlisting}
 #define  VIRTIO_MMIO_MSI_CMD_ENABLE           0x1
 #define  VIRTIO_MMIO_MSI_CMD_DISABLE          0x2
 #define  VIRTIO_MMIO_MSI_CMD_CONFIGURE        0x3
 #define  VIRTIO_MMIO_MSI_CMD_MASK             0x4
 #define  VIRTIO_MMIO_MSI_CMD_UNMASK           0x5
+#define  VIRTIO_MMIO_MSI_CMD_MAP_CONFIG       0x6
+#define  VIRTIO_MMIO_MSI_CMD_MAP_QUEUE        0x7
 \end{lstlisting}
 
 Setting a special NO_VECTOR value means disabling an interrupt for an event type.
@@ -1941,10 +1948,49 @@ \subsubsection{Device Initialization}\label{sec:Virtio Transport Options / Virti
 #define VIRTIO_MMIO_MSI_NO_VECTOR             0xffffffff
 \end{lstlisting}
 
+\subparagraph{MSI Vector and Event Mapping}\label{sec:Virtio Transport Options / Virtio Over MMIO / MMIO-specific Initialization And Device Operation / Device Initialization / MSI Vector Configuration}
+The reported \field{msi_sharing} bit in the \field{MsiState} return value shows
+the MSI sharing mode that device uses.
+
+When \field{msi_sharing} bit is 0, it indicates the device uses non-sharing mode
+and vector per event fixed static relationship is used. The first vector is for device
+configuraiton change event, the second vector is for virtqueue 1, the third vector
+is for virtqueue 2 and so on.
+
+When \field{msi_sharing} bit is 1, it indicates the device uses MSI sharing mode,
+and the vector and event mapping is dynamic. Writing \field{MsiVecSel}
+followed by writing VIRTIO_MMIO_MSI_CMD_MAP_CONFIG/VIRTIO_MMIO_MSI_CMD_MAP_QUEUE command
+maps interrupts triggered by the configuration change/selected queue events respectively
+to the corresponding MSI vector.
+
+\devicenormative{\subparagraph}{MSI Vector Configuration}{Virtio Transport Options / Virtio Over MMIO / MMIO-specific Initialization And Device Operation / MSI Vector Configuration}
+
+When the device reports \field{msi_sharing} bit as 0, it SHOULD support a number of
+vectors that greater than the maximum number of virtqueues.
+Device MUST report the number of vectors supported in \field{MsiVecNum}.
+
+When the device reports \field{msi_sharing} bit as 1, it SHOULD support at least
+2 MSI vectors and MUST report in \field{MsiVecNum}. Device SHOULD support mapping any
+event type to any vector under \field{MsiVecNum}.
+
+Device MUST support unmapping any event type (NO_VECTOR).
+
+The device SHOULD restrict the reported \field{msi_sharing} and \field{MsiVecNum}
+to a value that might benefit system performance.
+
+\begin{note}
+For example, a device which does not expect to send interrupts at a high rate might
+return \field{msi_sharing} bit as 1.
+\end{note}
+
 \drivernormative{\subparagraph}{MSI Vector Configuration}{Virtio Transport Options / Virtio Over MMIO / MMIO-specific Initialization And Device Operation / MSI Vector Configuration}
 When VIRTIO_F_MMIO_MSI has been negotiated, driver should try to configure
 and enable MSI.
 
+To set up the event and vector mapping for MSI sharing mode, driver SHOULD
+write a valid \field{MsiVecSel} followed by VIRTIO_MMIO_MSI_CMD_MAP_CONFIG/VIRTIO_MMIO_MSI_CMD_MAP_QUEUE
+command to map the configuration change/selected queue events respectively.
+
 To configure MSI vector, driver SHOULD firstly specify the MSI vector index by
 writing to \field{MsiVecSel}.
 Then notify the MSI address and data by writing to \field{MsiAddrLow}, \field{MsiAddrHigh},
diff --git a/msi-state.c b/msi-state.c
index b1fa0c1..d470be4 100644
--- a/msi-state.c
+++ b/msi-state.c
@@ -1,4 +1,5 @@
 le32 {
     msi_enabled : 1;
-    reserved : 31;
+    msi_sharing: 1;
+    reserved : 30;
 };
