new file mode 100644
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9533_mikrotik_routerboard-16m.dtsi"
+
+/ {
+ compatible = "mikrotik,routerboard-map-2nd", "qca,qca9533";
+ model = "MikroTik RouterBOARD mAP-2nD (mAP)";
+
+ aliases {
+ led-boot = &led_user;
+ led-failsafe = &led_user;
+ led-running = &led_user;
+ led-upgrade = &led_user;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power {
+ label = "green:power";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ eth_1 {
+ label = "green:eth_1";
+ gpios = <&gpio_ext 0 GPIO_ACTIVE_LOW>;
+ };
+
+ eth_2 {
+ label = "green:eth_2";
+ gpios = <&gpio_ext 1 GPIO_ACTIVE_LOW>;
+ };
+
+ poe_out {
+ label = "red:poe_out";
+ gpios = <&gpio_ext 2 GPIO_ACTIVE_LOW>;
+ };
+
+ led_user: user {
+ label = "green:user";
+ gpios = <&gpio_ext 3 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan {
+ label = "green:wlan";
+ gpios = <&gpio_ext 4 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ ap_cap {
+ label = "green:ap_cap";
+ gpios = <&gpio_ext 6 GPIO_ACTIVE_LOW>;
+ };
+
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+
+ usb_power {
+ gpio-export,name = "usb-power";
+ gpio-export,output = <1>;
+ gpios = <&gpio_ext 5 GPIO_ACTIVE_LOW>;
+ };
+
+ enable_poe_port5 {
+ gpio-export,name = "enable-poe";
+ gpio-export,output = <0>;
+ gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&spi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pin_spi_cs1>;
+
+ gpio_ext: gpio_ext@1 {
+ compatible = "fairchild,74hc595";
+ reg = <1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ registers-number = <1>;
+ spi-max-frequency = <25000000>;
+ };
+};
+
+
+&pinmux {
+ pin_spi_cs1: pinmux_spi_cs1 {
+ pinctrl-single,bits = <0x8 0x0a000000 0xff000000>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ phy-handle = <&swphy0>;
+
+ gmac-config {
+ device = <&gmac>;
+ switch-phy-swap = <1>;
+ };
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
@@ -55,6 +55,15 @@ define Device/mikrotik_routerboard-lhg-2nd
endef
TARGET_DEVICES += mikrotik_routerboard-lhg-2nd
+define Device/mikrotik_routerboard-map-2nd
+ $(Device/mikrotik_nor)
+ SOC := qca9533
+ DEVICE_MODEL := RouterBOARD mAP-2nD (mAP)
+ DEVICE_PACKAGES += kmod-usb2 kmod-ledtrig-gpio
+ IMAGE_SIZE := 16256k
+endef
+TARGET_DEVICES += mikrotik_routerboard-map-2nd
+
define Device/mikrotik_routerboard-mapl-2nd
$(Device/mikrotik_nor)
SOC := qca9533
@@ -18,6 +18,11 @@ mikrotik,routerboard-lhg-2nd|\
mikrotik,routerboard-mapl-2nd)
ucidef_set_led_netdev "lan" "lan" "green:lan" "eth0"
;;
+mikrotik,routerboard-map-2nd)
+ ucidef_set_led_netdev "eth_1" "eth_1" "green:eth_1" "eth1"
+ ucidef_set_led_switch "eth_2" "eth_2" "green:eth_2" "switch0" "0x4"
+ ucidef_set_led_gpio "poe" "poe" "red:poe_out" "14" "0"
+ ;;
mikrotik,routerboard-wapr-2nd)
ucidef_set_rssimon "wlan0" "200000" "1"
ucidef_set_led_rssi "rssilow" "rssilow" "green:rssilow" "wlan0" "1" "100"
@@ -29,6 +29,9 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
;;
+ mikrotik,routerboard-map-2nd)
+ ucidef_set_interface_lan "eth0 eth1"
+ ;;
*)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
;;
@@ -47,6 +50,7 @@ ath79_setup_macs()
mikrotik,routerboard-912uag-2hpnd|\
mikrotik,routerboard-921gs-5hpacd-15s|\
mikrotik,routerboard-lhg-2nd|\
+ mikrotik,routerboard-map-2nd|\
mikrotik,routerboard-mapl-2nd|\
mikrotik,routerboard-sxt-5nd-r2|\
mikrotik,routerboard-wap-g-5hact2hnd|\
@@ -29,6 +29,9 @@ case "$FIRMWARE" in
mikrotik,routerboard-wapr-2nd)
caldata_mikrotik_ath9k 0x1000 0x440 $(macaddr_add "$mac_base" +1)
;;
+ mikrotik,routerboard-map-2nd)
+ caldata_mikrotik_ath9k 0x1000 0x440 $(macaddr_add "$mac_base" 3)
+ ;;
mikrotik,routerboard-mapl-2nd|\
mikrotik,routerboard-wap-g-5hact2hnd)
caldata_mikrotik_ath9k 0x1000 0x440 $(macaddr_add "$mac_base" +2)
The MikroTik mAP-2nd (sold as mAP) is an indoor 2.4Ghz AP with 802.3af/at PoE input and passive PoE passthrough. See https://mikrotik.com/product/RBmAP2nD for more details. Specifications: - SoC: QCA9533 - RAM: 64MB - Storage: 16MB NOR - Wireless: QCA9533 802.11b/g/n 2x2 - Ethernet: 2x 10/100 ports, 802.3af/at PoE in port 1, 500 mA passive PoE out on port 2 - 7 user-controllable LEDs Note: the device is a tiny AP and does not distinguish between both ethernet ports roles, so they are both assigned to lan. With the current setup, ETH1 is connected to eth1 and ETH2 is connected to eth0 via the embedded switch port 2. Flashing: TFTP boot initramfs image and then perform sysupgrade. The "ETH1" port must be used to upload the TFTP image. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Tested-By: Andrew Powers-Holmes <aholmes@omnom.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit e1223dbee332b89caf71850eb909104529595c31) --- .../qca9533_mikrotik_routerboard-map-2nd.dts | 113 ++++++++++++++++++ target/linux/ath79/image/mikrotik.mk | 9 ++ .../mikrotik/base-files/etc/board.d/01_leds | 5 + .../base-files/etc/board.d/02_network | 4 + .../etc/hotplug.d/firmware/10-ath9k-eeprom | 3 + 5 files changed, 134 insertions(+) create mode 100644 target/linux/ath79/dts/qca9533_mikrotik_routerboard-map-2nd.dts