| Message ID | 20220309143100.2195-3-musashino.open@gmail.com |
|---|---|
| State | Accepted |
| Delegated to: | Hauke Mehrtens |
| Headers | show |
| Series | realtek: add support for Panasonic Switch-M8eG PN28080K | expand |
Hi Hiroshi, On Wed, 2022-03-09 at 23:31 +0900, INAGAKI Hiroshi wrote: > Panasonic Switch-M8eG PN28080K is a 8 + 1 port gigabit switch, based on > RTL8380M. > > Specification: > > - SoC : Realtek RTL8380M > - RAM : DDR3 128 MiB (Winbond W631GG8KB-15) > - Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G) > - Ethernet : 10/100/1000 Mbps x8 + 1 > - port 1-8 : TP, RTL8218B (SoC) > - port 9 : SFP, RTL8380M (SoC) > - LEDs/Keys : 7x / 1x > - UART : RS-232 port on the front panel (connector: RJ-45) > - 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45) > - 9600n8 > - Power : 100-240 VAC, 50/60 Hz, 0.5 A > - Plug : IEC 60320-C13 > - Stock OS : VxWorks based > > Flash instruction using initramfs image: > > 1. Prepare the TFTP server with the IP address 192.168.1.111 > 2. Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to > the TFTP directory > 3. Download the official upgrading firmware (ex: pn28080k_v30000.rom) > and place it to the TFTP directory > 4. Boot M8eG and interrupt the U-Boot with Ctrl + C keys > 5. Execute the following commands and boot with the OpenWrt initramfs > image > > rtk network on > tftpboot 0x81000000 > bootm > > 6. Backup mtdblock files to the computer by scp or anything and reboot > 7. Interrupt the U-Boot and execute the following commands to re-create > filesystem in the flash > > ffsmount c:/ > ffsfmt c:/ > > this step takes a long time, about ~ 4 mins > > 8. Execute the following commands to put the official images to the > filesystem > > updatert <official image> > > example: > > updatert pn28080k_v30000.rom > > this step takes about ~ 40 secs > > 9. Set the environment variables of the U-Boot by the following commands > > setenv loadaddr 0xb4e00000 > setenv bootcmd bootm > saveenv > > 10: Download the OpenWrt initramfs image and boot with it > > tftpboot 0x81000000 0101A8C0.img > bootm > > 11: On the initramfs image, download the sysupgrade image and perform > sysupgrade with it > > sysupgrade <imagename> > > 12: Wait ~ 120 seconds to complete flashing > > Note: > > - "Switch-M8eG" is a model name, and "PN28080K" is a model number. > Switch-M8eG has an another (old) model number ("PN28080"), it's not a > Realtek based hardware. > > - Switch-M8eG has a "POWER" LED (Green), but it's not connected to any > GPIO pin. > > - The U-Boot checks the runtime images in the flash when booting and > fails to execute anything in "bootcmd" variable if the images are not > exsisting. > > - A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock > firmware and it includes the stock images, configuration files and > checksum files. It's unknown format, can't be managed on the OpenWrt. > To get the enough space for OpenWrt, move the filesystem to the head > of "fs_reserved" partition by execution of "ffsfmt" and "updatert". > > - On the other devices in the same series of Switch-M8eG PN28080K, the > INT pin on the PCA9555 is not connected to anywhere. > > Back to the stock firmware: > > 1. Delete "loadaddr" variable and set "bootcmd" to the original value > > on U-Boot: > > setenv loadaddr > setenv bootcmd 'bootm 0x81000000' > > on OpenWrt: > > fw_setenv loadaddr > fw_setenv bootcmd 'bootm 0x81000000' > > 2. Perform reset or reboot > > on U-Boot: > > reset > > on OpenWrt: > > reboot > > Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> I still have one minor question and a small remark below, but otherwise this seems good to me. Reviewed-by: Sander Vanheule <sander@svanheule.net> > --- > v1 -> v2: > > - drop changes for kernel 5.4 > - add interrupt-related properties to the nodes of PCA9539 and PCA9555 > - use "gpio-keys" instead of "gpio-keys-polled" > - update/remove comments in mtd partitions > - use "led-*" scheme and add color/function properties for each node of > LEDs > - drop unnecessary default values from gpio-restart node > > v2 -> v3: > > - move interrupt related properties in PCA9539 to device dts > - move child i2c bus definitions in PCA9545 to device dts > - use actual SoC name "rtl8380" in second compatible of root > > v3 -> v4: > > - drop unnecessary "/delete-node/" of rtl8231 from dtsi > > .../rtl8380_panasonic_m8eg-pn28080k.dts | 133 ++++++++++++ > .../rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi | 195 ++++++++++++++++++ > target/linux/realtek/image/rtl838x.mk | 10 + > 3 files changed, 338 insertions(+) > create mode 100644 target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg- > pn28080k.dts > create mode 100644 target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg- > pn28xx0k.dtsi > > diff --git a/target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts > b/target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts > new file mode 100644 > index 0000000000..f9d58f5b66 > --- /dev/null > +++ b/target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts > @@ -0,0 +1,133 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > + > +#include "rtl838x.dtsi" > +#include "rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi" > + > +#include <dt-bindings/interrupt-controller/irq.h> > + > +/ { > + compatible = "panasonic,m8eg-pn28080k", "realtek,rtl8380-soc"; > + model = "Panasonic Switch-M8eG PN28080K"; > + > + aliases { > + led-boot = &led_status_eco_green; > + led-failsafe = &led_status_eco_amber; > + led-running = &led_status_eco_green; > + led-upgrade = &led_status_eco_green; > + }; > + > + sfp0: sfp-p9 { > + compatible = "sff,sfp"; > + i2c-bus = <&i2c0>; > + tx-fault-gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>; > + tx-disable-gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; > + mod-def0-gpio = <&gpio1 2 GPIO_ACTIVE_LOW>; > + los-gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>; > + }; > +}; > + > +&leds { > + led_status_eco_amber: led-5 { > + label = "amber:status_eco"; > + gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; > + color = <LED_COLOR_ID_AMBER>; > + function = LED_FUNCTION_STATUS; > + function-enumerator = <1>; > + }; > + > + led_status_eco_green: led-6 { > + label = "green:status_eco"; > + gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; > + color = <LED_COLOR_ID_GREEN>; > + function = LED_FUNCTION_STATUS; > + function-enumerator = <2>; > + }; > +}; > + > +&i2c_gpio_0 { > + scl-gpios = <&gpio0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + sda-gpios = <&gpio0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > +}; > + > +&i2c_gpio_1 { > + scl-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + sda-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > +}; > + > +&gpio1 { > + interrupt-controller; > + #interrupt-cells = <2>; > + interrupt-parent = <&gpio0>; > + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; > +}; > + > +&gpio2 { > + interrupt-controller; > + #interrupt-cells = <2>; > + interrupt-parent = <&gpio0>; > + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; > +}; > + > +&i2c_switch { > + i2c0: i2c@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0>; > + }; > +}; > + > +ðernet0 { > + mdio-bus { > + compatible = "realtek,rtl838x-mdio"; > + regmap = <ðernet0>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + INTERNAL_PHY(8) > + INTERNAL_PHY(9) > + INTERNAL_PHY(10) > + INTERNAL_PHY(11) > + INTERNAL_PHY(12) > + INTERNAL_PHY(13) > + INTERNAL_PHY(14) > + INTERNAL_PHY(15) > + > + INTERNAL_PHY(24) > + }; > +}; > + > +&switch0 { > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + SWITCH_PORT(8, 1, internal) > + SWITCH_PORT(9, 2, internal) > + SWITCH_PORT(10, 3, internal) > + SWITCH_PORT(11, 4, internal) > + SWITCH_PORT(12, 5, internal) > + SWITCH_PORT(13, 6, internal) > + SWITCH_PORT(14, 7, internal) > + SWITCH_PORT(15, 8, internal) > + > + port@24 { > + reg = <24>; > + label = "lan9"; > + phy-mode = "1000base-x"; > + phy-handle = <&phy24>; > + managed = "in-band-status"; > + sfp = <&sfp0>; > + }; > + > + port@28 { > + ethernet = <ðernet0>; > + reg = <28>; > + phy-mode = "internal"; > + > + fixed-link { > + speed = <1000>; > + full-duplex; > + }; > + }; > + }; > +}; > diff --git a/target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi > b/target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi > new file mode 100644 > index 0000000000..48aa1849d6 > --- /dev/null > +++ b/target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi > @@ -0,0 +1,195 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > + > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/leds/common.h> > + > +/ { > + chosen { > + bootargs = "console=ttyS0,9600"; > + }; > + > + memory@0 { > + device_type = "memory"; > + reg = <0x0 0x8000000>; > + }; > + > + leds: leds { > + compatible = "gpio-leds"; > + > + led-0 { > + label = "amber:any_col"; > + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; > + color = <LED_COLOR_ID_AMBER>; > + function = LED_FUNCTION_FAULT; > + }; > + > + led-1 { > + label = "green:giga"; > + gpios = <&gpio2 8 GPIO_ACTIVE_LOW>; > + color = <LED_COLOR_ID_GREEN>; > + function = LED_FUNCTION_INDICATOR; > + function-enumerator = <1>; > + }; > + > + led-2 { > + label = "green:100m"; > + gpios = <&gpio2 9 GPIO_ACTIVE_LOW>; > + color = <LED_COLOR_ID_GREEN>; > + function = LED_FUNCTION_INDICATOR; > + function-enumerator = <2>; > + }; > + > + led-3 { > + label = "green:full"; > + gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; > + color = <LED_COLOR_ID_GREEN>; > + function = LED_FUNCTION_INDICATOR; > + function-enumerator = <3>; > + }; > + > + led-4 { > + label = "green:loop_history"; > + gpios = <&gpio2 11 GPIO_ACTIVE_LOW>; > + color = <LED_COLOR_ID_GREEN>; > + function = LED_FUNCTION_INDICATOR; > + function-enumerator = <4>; > + }; > + }; > + > + keys { > + compatible = "gpio-keys"; > + > + led_mode { > + label = "led-mode"; > + gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; > + linux,code = <BTN_0>; > + }; > + }; > + > + gpio-restart { > + compatible = "gpio-restart"; > + gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>; > + }; > + > + i2c_gpio_0: i2c-gpio-0 { > + compatible = "i2c-gpio"; > + i2c-gpio,delay-us = <2>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + gpio1: gpio@20 { > + compatible = "nxp,pca9555"; > + reg = <0x20>; > + gpio-controller; > + #gpio-cells = <2>; > + }; > + > + gpio2: gpio@75 { > + compatible = "nxp,pca9539"; > + reg = <0x75>; > + gpio-controller; > + #gpio-cells = <2>; > + > + /* > + * GPIO14 (IO1_6): Shift Register RESET (port LED) > + * - Switch-M8eG PN28080K: 3x 74HC164 > + * - Switch-M24eG PN28240K: 6x 74HC164 > + * - Switch-M48eG PN28480K: 12x 74HC164 > + */ > + portled_sregister_reset { > + gpio-hog; > + gpios = <14 GPIO_ACTIVE_HIGH>; > + output-high; > + line-name = "portled-sregister-reset"; > + }; > + }; > + }; > + > + i2c_gpio_1: i2c-gpio-1 { > + compatible = "i2c-gpio"; > + i2c-gpio,delay-us = <2>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + i2c_switch: i2c-switch@70 { > + compatible = "nxp,pca9545"; > + reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; > + reg = <0x70>; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > +}; > + > +&spi0 { > + status = "okay"; > + > + flash@0 { > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <10000000>; > + > + partitions { > + compatible = "fixed-partitions"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + partition@0 { > + label = "u-boot"; > + reg = <0x0 0x80000>; > + read-only; > + }; > + > + partition@80000 { > + label = "u-boot-env"; > + reg = <0x80000 0x10000>; > + }; > + > + partition@90000 { > + label = "u-boot-env2"; > + reg = <0x90000 0x10000>; > + }; > + > + partition@a0000 { > + label = "sysinfo"; > + reg = <0xa0000 0x60000>; > + read-only; > + }; > + > + /* > + * Filesystem area in stock firmware > + * (0x100000-0x1DFFFFF) > + * > + * stock firmware images are required to pass > + * the checking by the U-Boot, also for OpenWrt > + * > + * in OpenWrt: > + * - 0x100000-0xDFFFFF (13M): stock images > + * - 0xE00000-0x1DFFFFF(16M): OpenWrt image > + */ > + partition@100000 { > + label = "fs_reserved"; > + reg = <0x100000 0xd00000>; You need this partition to be read-write, or can it be read-only too? > + }; > + > + partition@e00000 { > + compatible = "denx,uimage"; > + label = "firmware"; > + reg = <0xe00000 0x1000000>; > + }; > + > + partition@1e00000 { > + label = "vlog_data"; > + reg = <0x1e00000 0x100000>; > + read-only; > + }; > + > + partition@1f00000 { > + label = "elog_data"; > + reg = <0x1f00000 0x100000>; > + read-only; > + }; > + }; > + }; > +}; > diff --git a/target/linux/realtek/image/rtl838x.mk > b/target/linux/realtek/image/rtl838x.mk > index 43242d3eea..a133bc8d2a 100644 > --- a/target/linux/realtek/image/rtl838x.mk > +++ b/target/linux/realtek/image/rtl838x.mk > @@ -85,6 +85,16 @@ define Device/netgear_gs310tp-v1 > endef > TARGET_DEVICES += netgear_gs310tp-v1 > > +define Device/panasonic_m8eg-pn28080k > + SOC := rtl8380 > + IMAGE_SIZE := 16384k > + DEVICE_VENDOR := Panasonic > + DEVICE_MODEL := Switch-M8eG > + DEVICE_VARIANT := PN28080K Although it doens't appear to be common to use a part number for DEVICE_VARIANT, you indicate that these are basically "M8eG v1" and "M8eG v2". So this is OK for me. > + DEVICE_PACKAGES := kmod-i2c-mux-pca954x > +endef > +TARGET_DEVICES += panasonic_m8eg-pn28080k > + > define Device/zyxel_gs1900 > SOC := rtl8380 > IMAGE_SIZE := 6976k Best, Sander
Hi Sander, Thank you for your review. On 2022/03/13 19:41, Sander Vanheule wrote: > Hi Hiroshi, > > On Wed, 2022-03-09 at 23:31 +0900, INAGAKI Hiroshi wrote: >> Panasonic Switch-M8eG PN28080K is a 8 + 1 port gigabit switch, based on >> RTL8380M. >> >> Specification: >> >> - SoC : Realtek RTL8380M >> - RAM : DDR3 128 MiB (Winbond W631GG8KB-15) >> - Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G) >> - Ethernet : 10/100/1000 Mbps x8 + 1 >> - port 1-8 : TP, RTL8218B (SoC) >> - port 9 : SFP, RTL8380M (SoC) >> - LEDs/Keys : 7x / 1x >> - UART : RS-232 port on the front panel (connector: RJ-45) >> - 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45) >> - 9600n8 >> - Power : 100-240 VAC, 50/60 Hz, 0.5 A >> - Plug : IEC 60320-C13 >> - Stock OS : VxWorks based >> >> Flash instruction using initramfs image: >> >> 1. Prepare the TFTP server with the IP address 192.168.1.111 >> 2. Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to >> the TFTP directory >> 3. Download the official upgrading firmware (ex: pn28080k_v30000.rom) >> and place it to the TFTP directory >> 4. Boot M8eG and interrupt the U-Boot with Ctrl + C keys >> 5. Execute the following commands and boot with the OpenWrt initramfs >> image >> >> rtk network on >> tftpboot 0x81000000 >> bootm >> >> 6. Backup mtdblock files to the computer by scp or anything and reboot >> 7. Interrupt the U-Boot and execute the following commands to re-create >> filesystem in the flash >> >> ffsmount c:/ >> ffsfmt c:/ >> >> this step takes a long time, about ~ 4 mins >> >> 8. Execute the following commands to put the official images to the >> filesystem >> >> updatert <official image> >> >> example: >> >> updatert pn28080k_v30000.rom >> >> this step takes about ~ 40 secs >> >> 9. Set the environment variables of the U-Boot by the following commands >> >> setenv loadaddr 0xb4e00000 >> setenv bootcmd bootm >> saveenv >> >> 10: Download the OpenWrt initramfs image and boot with it >> >> tftpboot 0x81000000 0101A8C0.img >> bootm >> >> 11: On the initramfs image, download the sysupgrade image and perform >> sysupgrade with it >> >> sysupgrade <imagename> >> >> 12: Wait ~ 120 seconds to complete flashing >> >> Note: >> >> - "Switch-M8eG" is a model name, and "PN28080K" is a model number. >> Switch-M8eG has an another (old) model number ("PN28080"), it's not a >> Realtek based hardware. >> >> - Switch-M8eG has a "POWER" LED (Green), but it's not connected to any >> GPIO pin. >> >> - The U-Boot checks the runtime images in the flash when booting and >> fails to execute anything in "bootcmd" variable if the images are not >> exsisting. >> >> - A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock >> firmware and it includes the stock images, configuration files and >> checksum files. It's unknown format, can't be managed on the OpenWrt. >> To get the enough space for OpenWrt, move the filesystem to the head >> of "fs_reserved" partition by execution of "ffsfmt" and "updatert". >> >> - On the other devices in the same series of Switch-M8eG PN28080K, the >> INT pin on the PCA9555 is not connected to anywhere. >> >> Back to the stock firmware: >> >> 1. Delete "loadaddr" variable and set "bootcmd" to the original value >> >> on U-Boot: >> >> setenv loadaddr >> setenv bootcmd 'bootm 0x81000000' >> >> on OpenWrt: >> >> fw_setenv loadaddr >> fw_setenv bootcmd 'bootm 0x81000000' >> >> 2. Perform reset or reboot >> >> on U-Boot: >> >> reset >> >> on OpenWrt: >> >> reboot >> >> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> > I still have one minor question and a small remark below, but otherwise this seems > good to me. > > Reviewed-by: Sander Vanheule <sander@svanheule.net> > >> --- >> v1 -> v2: >> >> - drop changes for kernel 5.4 >> - add interrupt-related properties to the nodes of PCA9539 and PCA9555 >> - use "gpio-keys" instead of "gpio-keys-polled" >> - update/remove comments in mtd partitions >> - use "led-*" scheme and add color/function properties for each node of >> LEDs >> - drop unnecessary default values from gpio-restart node >> >> v2 -> v3: >> >> - move interrupt related properties in PCA9539 to device dts >> - move child i2c bus definitions in PCA9545 to device dts >> - use actual SoC name "rtl8380" in second compatible of root >> >> v3 -> v4: >> >> - drop unnecessary "/delete-node/" of rtl8231 from dtsi >> >> .../rtl8380_panasonic_m8eg-pn28080k.dts | 133 ++++++++++++ >> .../rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi | 195 ++++++++++++++++++ >> target/linux/realtek/image/rtl838x.mk | 10 + >> 3 files changed, 338 insertions(+) >> create mode 100644 target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg- >> pn28080k.dts >> create mode 100644 target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg- >> pn28xx0k.dtsi >> >> diff --git a/target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts >> b/target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts >> new file mode 100644 >> index 0000000000..f9d58f5b66 >> --- /dev/null >> +++ b/target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts >> @@ -0,0 +1,133 @@ >> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT >> + >> +#include "rtl838x.dtsi" >> +#include "rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi" >> + >> +#include <dt-bindings/interrupt-controller/irq.h> >> + >> +/ { >> + compatible = "panasonic,m8eg-pn28080k", "realtek,rtl8380-soc"; >> + model = "Panasonic Switch-M8eG PN28080K"; >> + >> + aliases { >> + led-boot = &led_status_eco_green; >> + led-failsafe = &led_status_eco_amber; >> + led-running = &led_status_eco_green; >> + led-upgrade = &led_status_eco_green; >> + }; >> + >> + sfp0: sfp-p9 { >> + compatible = "sff,sfp"; >> + i2c-bus = <&i2c0>; >> + tx-fault-gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>; >> + tx-disable-gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; >> + mod-def0-gpio = <&gpio1 2 GPIO_ACTIVE_LOW>; >> + los-gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>; >> + }; >> +}; >> + >> +&leds { >> + led_status_eco_amber: led-5 { >> + label = "amber:status_eco"; >> + gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; >> + color = <LED_COLOR_ID_AMBER>; >> + function = LED_FUNCTION_STATUS; >> + function-enumerator = <1>; >> + }; >> + >> + led_status_eco_green: led-6 { >> + label = "green:status_eco"; >> + gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; >> + color = <LED_COLOR_ID_GREEN>; >> + function = LED_FUNCTION_STATUS; >> + function-enumerator = <2>; >> + }; >> +}; >> + >> +&i2c_gpio_0 { >> + scl-gpios = <&gpio0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; >> + sda-gpios = <&gpio0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; >> +}; >> + >> +&i2c_gpio_1 { >> + scl-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; >> + sda-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; >> +}; >> + >> +&gpio1 { >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + interrupt-parent = <&gpio0>; >> + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; >> +}; >> + >> +&gpio2 { >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + interrupt-parent = <&gpio0>; >> + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; >> +}; >> + >> +&i2c_switch { >> + i2c0: i2c@0 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + reg = <0>; >> + }; >> +}; >> + >> +ðernet0 { >> + mdio-bus { >> + compatible = "realtek,rtl838x-mdio"; >> + regmap = <ðernet0>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + INTERNAL_PHY(8) >> + INTERNAL_PHY(9) >> + INTERNAL_PHY(10) >> + INTERNAL_PHY(11) >> + INTERNAL_PHY(12) >> + INTERNAL_PHY(13) >> + INTERNAL_PHY(14) >> + INTERNAL_PHY(15) >> + >> + INTERNAL_PHY(24) >> + }; >> +}; >> + >> +&switch0 { >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + SWITCH_PORT(8, 1, internal) >> + SWITCH_PORT(9, 2, internal) >> + SWITCH_PORT(10, 3, internal) >> + SWITCH_PORT(11, 4, internal) >> + SWITCH_PORT(12, 5, internal) >> + SWITCH_PORT(13, 6, internal) >> + SWITCH_PORT(14, 7, internal) >> + SWITCH_PORT(15, 8, internal) >> + >> + port@24 { >> + reg = <24>; >> + label = "lan9"; >> + phy-mode = "1000base-x"; >> + phy-handle = <&phy24>; >> + managed = "in-band-status"; >> + sfp = <&sfp0>; >> + }; >> + >> + port@28 { >> + ethernet = <ðernet0>; >> + reg = <28>; >> + phy-mode = "internal"; >> + >> + fixed-link { >> + speed = <1000>; >> + full-duplex; >> + }; >> + }; >> + }; >> +}; >> diff --git a/target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi >> b/target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi >> new file mode 100644 >> index 0000000000..48aa1849d6 >> --- /dev/null >> +++ b/target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi >> @@ -0,0 +1,195 @@ >> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT >> + >> +#include <dt-bindings/input/input.h> >> +#include <dt-bindings/gpio/gpio.h> >> +#include <dt-bindings/leds/common.h> >> + >> +/ { >> + chosen { >> + bootargs = "console=ttyS0,9600"; >> + }; >> + >> + memory@0 { >> + device_type = "memory"; >> + reg = <0x0 0x8000000>; >> + }; >> + >> + leds: leds { >> + compatible = "gpio-leds"; >> + >> + led-0 { >> + label = "amber:any_col"; >> + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; >> + color = <LED_COLOR_ID_AMBER>; >> + function = LED_FUNCTION_FAULT; >> + }; >> + >> + led-1 { >> + label = "green:giga"; >> + gpios = <&gpio2 8 GPIO_ACTIVE_LOW>; >> + color = <LED_COLOR_ID_GREEN>; >> + function = LED_FUNCTION_INDICATOR; >> + function-enumerator = <1>; >> + }; >> + >> + led-2 { >> + label = "green:100m"; >> + gpios = <&gpio2 9 GPIO_ACTIVE_LOW>; >> + color = <LED_COLOR_ID_GREEN>; >> + function = LED_FUNCTION_INDICATOR; >> + function-enumerator = <2>; >> + }; >> + >> + led-3 { >> + label = "green:full"; >> + gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; >> + color = <LED_COLOR_ID_GREEN>; >> + function = LED_FUNCTION_INDICATOR; >> + function-enumerator = <3>; >> + }; >> + >> + led-4 { >> + label = "green:loop_history"; >> + gpios = <&gpio2 11 GPIO_ACTIVE_LOW>; >> + color = <LED_COLOR_ID_GREEN>; >> + function = LED_FUNCTION_INDICATOR; >> + function-enumerator = <4>; >> + }; >> + }; >> + >> + keys { >> + compatible = "gpio-keys"; >> + >> + led_mode { >> + label = "led-mode"; >> + gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; >> + linux,code = <BTN_0>; >> + }; >> + }; >> + >> + gpio-restart { >> + compatible = "gpio-restart"; >> + gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>; >> + }; >> + >> + i2c_gpio_0: i2c-gpio-0 { >> + compatible = "i2c-gpio"; >> + i2c-gpio,delay-us = <2>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + gpio1: gpio@20 { >> + compatible = "nxp,pca9555"; >> + reg = <0x20>; >> + gpio-controller; >> + #gpio-cells = <2>; >> + }; >> + >> + gpio2: gpio@75 { >> + compatible = "nxp,pca9539"; >> + reg = <0x75>; >> + gpio-controller; >> + #gpio-cells = <2>; >> + >> + /* >> + * GPIO14 (IO1_6): Shift Register RESET (port LED) >> + * - Switch-M8eG PN28080K: 3x 74HC164 >> + * - Switch-M24eG PN28240K: 6x 74HC164 >> + * - Switch-M48eG PN28480K: 12x 74HC164 >> + */ >> + portled_sregister_reset { >> + gpio-hog; >> + gpios = <14 GPIO_ACTIVE_HIGH>; >> + output-high; >> + line-name = "portled-sregister-reset"; >> + }; >> + }; >> + }; >> + >> + i2c_gpio_1: i2c-gpio-1 { >> + compatible = "i2c-gpio"; >> + i2c-gpio,delay-us = <2>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + i2c_switch: i2c-switch@70 { >> + compatible = "nxp,pca9545"; >> + reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; >> + reg = <0x70>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + }; >> + }; >> +}; >> + >> +&spi0 { >> + status = "okay"; >> + >> + flash@0 { >> + compatible = "jedec,spi-nor"; >> + reg = <0>; >> + spi-max-frequency = <10000000>; >> + >> + partitions { >> + compatible = "fixed-partitions"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + >> + partition@0 { >> + label = "u-boot"; >> + reg = <0x0 0x80000>; >> + read-only; >> + }; >> + >> + partition@80000 { >> + label = "u-boot-env"; >> + reg = <0x80000 0x10000>; >> + }; >> + >> + partition@90000 { >> + label = "u-boot-env2"; >> + reg = <0x90000 0x10000>; >> + }; >> + >> + partition@a0000 { >> + label = "sysinfo"; >> + reg = <0xa0000 0x60000>; >> + read-only; >> + }; >> + >> + /* >> + * Filesystem area in stock firmware >> + * (0x100000-0x1DFFFFF) >> + * >> + * stock firmware images are required to pass >> + * the checking by the U-Boot, also for OpenWrt >> + * >> + * in OpenWrt: >> + * - 0x100000-0xDFFFFF (13M): stock images >> + * - 0xE00000-0x1DFFFFF(16M): OpenWrt image >> + */ >> + partition@100000 { >> + label = "fs_reserved"; >> + reg = <0x100000 0xd00000>; > You need this partition to be read-write, or can it be read-only too? I left the "fs_reserved" partition as read-write for the case the user wants to recover to original state completely with backup. Before OpenWrt installation, firmware data of stock may exist across these two partitions, but after the installation, the data is moved forward in "fs_reserved", so the installation changes from its original state. > >> + }; >> + >> + partition@e00000 { >> + compatible = "denx,uimage"; >> + label = "firmware"; >> + reg = <0xe00000 0x1000000>; >> + }; >> + >> + partition@1e00000 { >> + label = "vlog_data"; >> + reg = <0x1e00000 0x100000>; >> + read-only; >> + }; >> + >> + partition@1f00000 { >> + label = "elog_data"; >> + reg = <0x1f00000 0x100000>; >> + read-only; >> + }; >> + }; >> + }; >> +}; >> diff --git a/target/linux/realtek/image/rtl838x.mk >> b/target/linux/realtek/image/rtl838x.mk >> index 43242d3eea..a133bc8d2a 100644 >> --- a/target/linux/realtek/image/rtl838x.mk >> +++ b/target/linux/realtek/image/rtl838x.mk >> @@ -85,6 +85,16 @@ define Device/netgear_gs310tp-v1 >> endef >> TARGET_DEVICES += netgear_gs310tp-v1 >> >> +define Device/panasonic_m8eg-pn28080k >> + SOC := rtl8380 >> + IMAGE_SIZE := 16384k >> + DEVICE_VENDOR := Panasonic >> + DEVICE_MODEL := Switch-M8eG >> + DEVICE_VARIANT := PN28080K > Although it doens't appear to be common to use a part number for DEVICE_VARIANT, you > indicate that these are basically "M8eG v1" and "M8eG v2". So this is OK for me. > >> + DEVICE_PACKAGES := kmod-i2c-mux-pca954x >> +endef >> +TARGET_DEVICES += panasonic_m8eg-pn28080k >> + >> define Device/zyxel_gs1900 >> SOC := rtl8380 >> IMAGE_SIZE := 6976k > > Best, > Sander Regards, Hiroshi
diff --git a/target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts b/target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts new file mode 100644 index 0000000000..f9d58f5b66 --- /dev/null +++ b/target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts @@ -0,0 +1,133 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "rtl838x.dtsi" +#include "rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi" + +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + compatible = "panasonic,m8eg-pn28080k", "realtek,rtl8380-soc"; + model = "Panasonic Switch-M8eG PN28080K"; + + aliases { + led-boot = &led_status_eco_green; + led-failsafe = &led_status_eco_amber; + led-running = &led_status_eco_green; + led-upgrade = &led_status_eco_green; + }; + + sfp0: sfp-p9 { + compatible = "sff,sfp"; + i2c-bus = <&i2c0>; + tx-fault-gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>; + tx-disable-gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 2 GPIO_ACTIVE_LOW>; + los-gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>; + }; +}; + +&leds { + led_status_eco_amber: led-5 { + label = "amber:status_eco"; + gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_AMBER>; + function = LED_FUNCTION_STATUS; + function-enumerator = <1>; + }; + + led_status_eco_green: led-6 { + label = "green:status_eco"; + gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_STATUS; + function-enumerator = <2>; + }; +}; + +&i2c_gpio_0 { + scl-gpios = <&gpio0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; +}; + +&i2c_gpio_1 { + scl-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; +}; + +&gpio1 { + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gpio0>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; +}; + +&gpio2 { + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gpio0>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; +}; + +&i2c_switch { + i2c0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; +}; + +ðernet0 { + mdio-bus { + compatible = "realtek,rtl838x-mdio"; + regmap = <ðernet0>; + #address-cells = <1>; + #size-cells = <0>; + + INTERNAL_PHY(8) + INTERNAL_PHY(9) + INTERNAL_PHY(10) + INTERNAL_PHY(11) + INTERNAL_PHY(12) + INTERNAL_PHY(13) + INTERNAL_PHY(14) + INTERNAL_PHY(15) + + INTERNAL_PHY(24) + }; +}; + +&switch0 { + ports { + #address-cells = <1>; + #size-cells = <0>; + + SWITCH_PORT(8, 1, internal) + SWITCH_PORT(9, 2, internal) + SWITCH_PORT(10, 3, internal) + SWITCH_PORT(11, 4, internal) + SWITCH_PORT(12, 5, internal) + SWITCH_PORT(13, 6, internal) + SWITCH_PORT(14, 7, internal) + SWITCH_PORT(15, 8, internal) + + port@24 { + reg = <24>; + label = "lan9"; + phy-mode = "1000base-x"; + phy-handle = <&phy24>; + managed = "in-band-status"; + sfp = <&sfp0>; + }; + + port@28 { + ethernet = <ðernet0>; + reg = <28>; + phy-mode = "internal"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; +}; diff --git a/target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi b/target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi new file mode 100644 index 0000000000..48aa1849d6 --- /dev/null +++ b/target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi @@ -0,0 +1,195 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> + +/ { + chosen { + bootargs = "console=ttyS0,9600"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x8000000>; + }; + + leds: leds { + compatible = "gpio-leds"; + + led-0 { + label = "amber:any_col"; + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_AMBER>; + function = LED_FUNCTION_FAULT; + }; + + led-1 { + label = "green:giga"; + gpios = <&gpio2 8 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_INDICATOR; + function-enumerator = <1>; + }; + + led-2 { + label = "green:100m"; + gpios = <&gpio2 9 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_INDICATOR; + function-enumerator = <2>; + }; + + led-3 { + label = "green:full"; + gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_INDICATOR; + function-enumerator = <3>; + }; + + led-4 { + label = "green:loop_history"; + gpios = <&gpio2 11 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_INDICATOR; + function-enumerator = <4>; + }; + }; + + keys { + compatible = "gpio-keys"; + + led_mode { + label = "led-mode"; + gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; + linux,code = <BTN_0>; + }; + }; + + gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>; + }; + + i2c_gpio_0: i2c-gpio-0 { + compatible = "i2c-gpio"; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + + gpio1: gpio@20 { + compatible = "nxp,pca9555"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio2: gpio@75 { + compatible = "nxp,pca9539"; + reg = <0x75>; + gpio-controller; + #gpio-cells = <2>; + + /* + * GPIO14 (IO1_6): Shift Register RESET (port LED) + * - Switch-M8eG PN28080K: 3x 74HC164 + * - Switch-M24eG PN28240K: 6x 74HC164 + * - Switch-M48eG PN28480K: 12x 74HC164 + */ + portled_sregister_reset { + gpio-hog; + gpios = <14 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "portled-sregister-reset"; + }; + }; + }; + + i2c_gpio_1: i2c-gpio-1 { + compatible = "i2c-gpio"; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + + i2c_switch: i2c-switch@70 { + compatible = "nxp,pca9545"; + reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "u-boot-env"; + reg = <0x80000 0x10000>; + }; + + partition@90000 { + label = "u-boot-env2"; + reg = <0x90000 0x10000>; + }; + + partition@a0000 { + label = "sysinfo"; + reg = <0xa0000 0x60000>; + read-only; + }; + + /* + * Filesystem area in stock firmware + * (0x100000-0x1DFFFFF) + * + * stock firmware images are required to pass + * the checking by the U-Boot, also for OpenWrt + * + * in OpenWrt: + * - 0x100000-0xDFFFFF (13M): stock images + * - 0xE00000-0x1DFFFFF(16M): OpenWrt image + */ + partition@100000 { + label = "fs_reserved"; + reg = <0x100000 0xd00000>; + }; + + partition@e00000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0xe00000 0x1000000>; + }; + + partition@1e00000 { + label = "vlog_data"; + reg = <0x1e00000 0x100000>; + read-only; + }; + + partition@1f00000 { + label = "elog_data"; + reg = <0x1f00000 0x100000>; + read-only; + }; + }; + }; +}; diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk index 43242d3eea..a133bc8d2a 100644 --- a/target/linux/realtek/image/rtl838x.mk +++ b/target/linux/realtek/image/rtl838x.mk @@ -85,6 +85,16 @@ define Device/netgear_gs310tp-v1 endef TARGET_DEVICES += netgear_gs310tp-v1 +define Device/panasonic_m8eg-pn28080k + SOC := rtl8380 + IMAGE_SIZE := 16384k + DEVICE_VENDOR := Panasonic + DEVICE_MODEL := Switch-M8eG + DEVICE_VARIANT := PN28080K + DEVICE_PACKAGES := kmod-i2c-mux-pca954x +endef +TARGET_DEVICES += panasonic_m8eg-pn28080k + define Device/zyxel_gs1900 SOC := rtl8380 IMAGE_SIZE := 6976k
Panasonic Switch-M8eG PN28080K is a 8 + 1 port gigabit switch, based on RTL8380M. Specification: - SoC : Realtek RTL8380M - RAM : DDR3 128 MiB (Winbond W631GG8KB-15) - Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G) - Ethernet : 10/100/1000 Mbps x8 + 1 - port 1-8 : TP, RTL8218B (SoC) - port 9 : SFP, RTL8380M (SoC) - LEDs/Keys : 7x / 1x - UART : RS-232 port on the front panel (connector: RJ-45) - 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45) - 9600n8 - Power : 100-240 VAC, 50/60 Hz, 0.5 A - Plug : IEC 60320-C13 - Stock OS : VxWorks based Flash instruction using initramfs image: 1. Prepare the TFTP server with the IP address 192.168.1.111 2. Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to the TFTP directory 3. Download the official upgrading firmware (ex: pn28080k_v30000.rom) and place it to the TFTP directory 4. Boot M8eG and interrupt the U-Boot with Ctrl + C keys 5. Execute the following commands and boot with the OpenWrt initramfs image rtk network on tftpboot 0x81000000 bootm 6. Backup mtdblock files to the computer by scp or anything and reboot 7. Interrupt the U-Boot and execute the following commands to re-create filesystem in the flash ffsmount c:/ ffsfmt c:/ this step takes a long time, about ~ 4 mins 8. Execute the following commands to put the official images to the filesystem updatert <official image> example: updatert pn28080k_v30000.rom this step takes about ~ 40 secs 9. Set the environment variables of the U-Boot by the following commands setenv loadaddr 0xb4e00000 setenv bootcmd bootm saveenv 10: Download the OpenWrt initramfs image and boot with it tftpboot 0x81000000 0101A8C0.img bootm 11: On the initramfs image, download the sysupgrade image and perform sysupgrade with it sysupgrade <imagename> 12: Wait ~ 120 seconds to complete flashing Note: - "Switch-M8eG" is a model name, and "PN28080K" is a model number. Switch-M8eG has an another (old) model number ("PN28080"), it's not a Realtek based hardware. - Switch-M8eG has a "POWER" LED (Green), but it's not connected to any GPIO pin. - The U-Boot checks the runtime images in the flash when booting and fails to execute anything in "bootcmd" variable if the images are not exsisting. - A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock firmware and it includes the stock images, configuration files and checksum files. It's unknown format, can't be managed on the OpenWrt. To get the enough space for OpenWrt, move the filesystem to the head of "fs_reserved" partition by execution of "ffsfmt" and "updatert". - On the other devices in the same series of Switch-M8eG PN28080K, the INT pin on the PCA9555 is not connected to anywhere. Back to the stock firmware: 1. Delete "loadaddr" variable and set "bootcmd" to the original value on U-Boot: setenv loadaddr setenv bootcmd 'bootm 0x81000000' on OpenWrt: fw_setenv loadaddr fw_setenv bootcmd 'bootm 0x81000000' 2. Perform reset or reboot on U-Boot: reset on OpenWrt: reboot Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> --- v1 -> v2: - drop changes for kernel 5.4 - add interrupt-related properties to the nodes of PCA9539 and PCA9555 - use "gpio-keys" instead of "gpio-keys-polled" - update/remove comments in mtd partitions - use "led-*" scheme and add color/function properties for each node of LEDs - drop unnecessary default values from gpio-restart node v2 -> v3: - move interrupt related properties in PCA9539 to device dts - move child i2c bus definitions in PCA9545 to device dts - use actual SoC name "rtl8380" in second compatible of root v3 -> v4: - drop unnecessary "/delete-node/" of rtl8231 from dtsi .../rtl8380_panasonic_m8eg-pn28080k.dts | 133 ++++++++++++ .../rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi | 195 ++++++++++++++++++ target/linux/realtek/image/rtl838x.mk | 10 + 3 files changed, 338 insertions(+) create mode 100644 target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts create mode 100644 target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi