diff mbox series

[v2,3/6] rtl838x: add support for D-Link DGS-1210-28

Message ID 20201104164725.4549-4-ynezz@true.cz
State Accepted
Delegated to: Petr Štetiar
Headers show
Series rtl838x: add support for D-Link DGS-1210-28 | expand

Commit Message

Petr Štetiar Nov. 4, 2020, 4:47 p.m. UTC 
Hardware specification
 ----------------------

 * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
 * 128MB DRAM
 * 32MB NOR Flash (MX25L25635E)
 * 24 x 10/100/1000BASE-T ports
    - Internal PHY with 8 ports (RTL8218B)
    - Two external PHYs with 8 ports each (RTL8218B)
 * 4 x Gigabit RJ45/SFP Combo ports
    - External PHY with 4 SFP ports (RTL8214FC)
 * Power LED
 * Reset button on front panel
 * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6

 UART pinout
 -----------

  [oooo]J3 [o]ooo|J6
    |       ^ ||`------ GND
    |       | |`------- RX
    |       | `-------- TX
    |       `---------- Vcc (3V3)
    |
    `------------------ J3 is power input connector nearby J6 UART

 Boot initramfs image from U-Boot
 --------------------------------

  1. Press Escape key during `Hit Esc key to stop autoboot` prompt
  2. Press CTRL+C keys to get into real U-Boot prompt
  3. Init network with `rtk network on` command
  4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-16-initramfs-kernel.bin` command
  5. Boot the image with `bootm` command

To install, upload the sysupgrade image to the OEM webpage or sysupgrade
from the system running from initramfs image.

It has been developed and tested on device with F1 revision.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
---
 .../dts/rtl8382_d-link_dgs-1210-28.dts        | 339 ++++++++++++++++++
 target/linux/rtl838x/image/Makefile           |   5 +
 2 files changed, 344 insertions(+)
 create mode 100644 target/linux/rtl838x/dts/rtl8382_d-link_dgs-1210-28.dts
diff mbox series

Patch

diff --git a/target/linux/rtl838x/dts/rtl8382_d-link_dgs-1210-28.dts b/target/linux/rtl838x/dts/rtl8382_d-link_dgs-1210-28.dts
new file mode 100644
index 000000000000..f154ca963d1c
--- /dev/null
+++ b/target/linux/rtl838x/dts/rtl8382_d-link_dgs-1210-28.dts
@@ -0,0 +1,339 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl8382_d-link_dgs-1210.dtsi"
+
+/ {
+	compatible = "d-link,dgs-1210-28", "realtek,rtl838x-soc";
+	model = "D-Link DGS-1210-28";
+};
+
+&ethernet0 {
+	mdio: mdio-bus {
+		compatible = "realtek,rtl838x-mdio";
+		regmap = <&ethernet0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* External phy RTL8218B */
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy1: ethernet-phy@1 {
+			reg = <1>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy2: ethernet-phy@2 {
+			reg = <2>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy3: ethernet-phy@3 {
+			reg = <3>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy4: ethernet-phy@4 {
+			reg = <4>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy5: ethernet-phy@5 {
+			reg = <5>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy6: ethernet-phy@6 {
+			reg = <6>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy7: ethernet-phy@7 {
+			reg = <7>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+
+		/* Internal phy RTL8218B */
+		phy8: ethernet-phy@8 {
+			reg = <8>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+			phy-is-integrated;
+		};
+		phy9: ethernet-phy@9 {
+			reg = <9>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+			phy-is-integrated;
+		};
+		phy10: ethernet-phy@10 {
+			reg = <10>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+			phy-is-integrated;
+		};
+		phy11: ethernet-phy@11 {
+			reg = <11>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+			phy-is-integrated;
+		};
+		phy12: ethernet-phy@12 {
+			reg = <12>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+			phy-is-integrated;
+		};
+		phy13: ethernet-phy@13 {
+			reg = <13>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+			phy-is-integrated;
+		};
+		phy14: ethernet-phy@14 {
+			reg = <14>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+			phy-is-integrated;
+		};
+		phy15: ethernet-phy@15 {
+			reg = <15>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+			phy-is-integrated;
+		};
+
+		/* External phy RTL8218B */
+		phy16: ethernet-phy@16 {
+			reg = <16>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy17: ethernet-phy@17 {
+			reg = <17>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy18: ethernet-phy@18 {
+			reg = <18>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy19: ethernet-phy@19 {
+			reg = <19>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy20: ethernet-phy@20 {
+			reg = <20>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy21: ethernet-phy@21 {
+			reg = <21>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy22: ethernet-phy@22 {
+			reg = <22>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+		phy23: ethernet-phy@23 {
+			reg = <23>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+
+		/* External phy: RTL8214FC */
+		phy24: ethernet-phy@24 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			sfp;
+			media = "fibre";
+			reg = <24>;
+		};
+		phy25: ethernet-phy@25 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			sfp;
+			media = "fibre";
+			reg = <25>;
+		};
+		phy26: ethernet-phy@26 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			sfp;
+			media = "fibre";
+			reg = <26>;
+		};
+		phy27: ethernet-phy@27 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			sfp;
+			media = "fibre";
+			reg = <27>;
+		};
+	};
+};
+
+&switch0 {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan1";
+			phy-handle = <&phy0>;
+			phy-mode = "qsgmii";
+		};
+		port@1 {
+			reg = <1>;
+			label = "lan2";
+			phy-handle = <&phy1>;
+			phy-mode = "qsgmii";
+		};
+		port@2 {
+			reg = <2>;
+			label = "lan3";
+			phy-handle = <&phy2>;
+			phy-mode = "qsgmii";
+		};
+		port@3 {
+			reg = <3>;
+			label = "lan4";
+			phy-handle = <&phy3>;
+			phy-mode = "qsgmii";
+		};
+		port@4 {
+			reg = <4>;
+			label = "lan5";
+			phy-handle = <&phy4>;
+			phy-mode = "qsgmii";
+		};
+		port@5 {
+			reg = <5>;
+			label = "lan6";
+			phy-handle = <&phy5>;
+			phy-mode = "qsgmii";
+		};
+		port@6 {
+			reg = <6>;
+			label = "lan7";
+			phy-handle = <&phy6>;
+			phy-mode = "qsgmii";
+		};
+		port@7 {
+			reg = <7>;
+			label = "lan8";
+			phy-handle = <&phy7>;
+			phy-mode = "qsgmii";
+		};
+		port@8 {
+			reg = <8>;
+			label = "lan9";
+			phy-handle = <&phy8>;
+			phy-mode = "internal";
+		};
+		port@9 {
+			reg = <9>;
+			label = "lan10";
+			phy-handle = <&phy9>;
+			phy-mode = "internal";
+		};
+		port@10 {
+			reg = <10>;
+			label = "lan11";
+			phy-handle = <&phy10>;
+			phy-mode = "internal";
+		};
+		port@11 {
+			reg = <11>;
+			label = "lan12";
+			phy-handle = <&phy11>;
+			phy-mode = "internal";
+		};
+		port@12 {
+			reg = <12>;
+			label = "lan13";
+			phy-handle = <&phy12>;
+			phy-mode = "internal";
+		};
+		port@13 {
+			reg = <13>;
+			label = "lan14";
+			phy-handle = <&phy13>;
+			phy-mode = "internal";
+		};
+		port@14 {
+			reg = <14>;
+			label = "lan15";
+			phy-handle = <&phy14>;
+			phy-mode = "internal";
+		};
+		port@15 {
+			reg = <15>;
+			label = "lan16";
+			phy-handle = <&phy15>;
+			phy-mode = "internal";
+		};
+		port@16 {
+			reg = <16>;
+			label = "lan17";
+			phy-handle = <&phy16>;
+			phy-mode = "qsgmii";
+		};
+		port@17 {
+			reg = <17>;
+			label = "lan18";
+			phy-handle = <&phy17>;
+			phy-mode = "qsgmii";
+		};
+		port@18 {
+			reg = <18>;
+			label = "lan19";
+			phy-handle = <&phy18>;
+			phy-mode = "qsgmii";
+		};
+		port@19 {
+			reg = <19>;
+			label = "lan20";
+			phy-handle = <&phy19>;
+			phy-mode = "qsgmii";
+		};
+		port@20 {
+			reg = <20>;
+			label = "lan21";
+			phy-handle = <&phy20>;
+			phy-mode = "qsgmii";
+		};
+		port@21 {
+			reg = <21>;
+			label = "lan22";
+			phy-handle = <&phy21>;
+			phy-mode = "qsgmii";
+		};
+		port@22 {
+			reg = <22>;
+			label = "lan23";
+			phy-handle = <&phy22>;
+			phy-mode = "qsgmii";
+		};
+		port@23 {
+			reg = <23>;
+			label = "lan24";
+			phy-handle = <&phy23>;
+			phy-mode = "qsgmii";
+		};
+
+		port@24 {
+			reg = <24>;
+			label = "lan25";
+			phy-handle = <&phy24>;
+			phy-mode = "qsgmii";
+		};
+		port@25 {
+			reg = <25>;
+			label = "lan26";
+			phy-handle = <&phy25>;
+			phy-mode = "qsgmii";
+		};
+		port@26 {
+			reg = <26>;
+			label = "lan27";
+			phy-handle = <&phy26>;
+			phy-mode = "qsgmii";
+		};
+		port@27 {
+			reg = <27>;
+			label = "lan28";
+			phy-handle = <&phy27>;
+			phy-mode = "qsgmii";
+		};
+		port@28 {
+			ethernet = <&ethernet0>;
+			reg = <28>;
+			phy-mode = "internal";
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
diff --git a/target/linux/rtl838x/image/Makefile b/target/linux/rtl838x/image/Makefile
index cd384c534522..51acd41c7621 100644
--- a/target/linux/rtl838x/image/Makefile
+++ b/target/linux/rtl838x/image/Makefile
@@ -61,4 +61,9 @@  define Device/d-link_dgs-1210-16
 endef
 TARGET_DEVICES += d-link_dgs-1210-16
 
+define Device/d-link_dgs-1210-28
+  $(Device/d-link_dgs-1210)
+  DEVICE_MODEL := DGS-1210-28
+endef
+TARGET_DEVICES += d-link_dgs-1210-28
 $(eval $(call BuildImage))