diff mbox series

[v2] ath79: fix ath10k caldata extraction on some D-Link DIR-842 C3 devices

Message ID 20201027110253.7880-1-fercerpav@gmail.com
State Accepted
Headers show
Series [v2] ath79: fix ath10k caldata extraction on some D-Link DIR-842 C3 devices | expand

Commit Message

Paul Fertser Oct. 27, 2020, 11:02 a.m. UTC
According to forum threads [0][1] and a report on IRC by Doc-Saintly
some of those boards have calibration data in a different place. Only
one alternative location is known.

Without proper board calibration data (board.bin having all 0xff bytes)
ath10k firmware still tries to load but crashes on startup with a
confusing error message.

If you're applying this patch manually on your device do not forget to
remove /lib/firmware/ath10k/pre-cal-pci-0000:00:00.0.bin and reboot to
force caldata re-extraction.

[0] https://forum.openwrt.org/t/support-for-d-link-dir842-rev-c3/41654
[1] https://forum.openwrt.org/t/d-link-dir-842-cant-access-firmware-upload-form/65454

Signed-off-by: Paul Fertser <fercerpav@gmail.com>
---

Changes in v2:

  - Separate out nec,wg1200cr section as those boards do not even have
    a "reserved" partition (Adrian Schmutzler)

 .../base-files/etc/hotplug.d/firmware/11-ath10k-caldata  | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)
diff mbox series

Patch

diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 25e864ba72..ca994a4e52 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -167,13 +167,18 @@  case "$FIRMWARE" in
 		;;
 	dlink,dir-842-c1|\
 	dlink,dir-842-c2|\
-	dlink,dir-842-c3|\
-	nec,wg1200cr)
+	dlink,dir-842-c3)
 		caldata_extract "art" 0x5000 0x2f20
+		caldata_valid "202f" || caldata_extract "reserved" 0x15000 0x2f20
 		ath10k_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
 		ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
 			/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
 		;;
+	nec,wg1200cr)
+		caldata_extract "art" 0x5000 0x2f20
+		ath10k_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
+		ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
+			/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
 	netgear,ex6400|\
 	netgear,ex7300)
 		caldata_extract "caldata" 0x5000 0x2f20