@@ -1044,10 +1044,39 @@ static void ftgmac100_adjust_link(struct net_device *netdev)
schedule_work(&priv->reset_task);
}
-static int ftgmac100_mii_probe(struct ftgmac100 *priv, phy_interface_t intf)
+static int ftgmac100_mii_probe(struct net_device *netdev)
{
- struct net_device *netdev = priv->netdev;
+ struct ftgmac100 *priv = netdev_priv(netdev);
+ struct platform_device *pdev = to_platform_device(priv->dev);
+ struct device_node *np = pdev->dev.of_node;
struct phy_device *phydev;
+ phy_interface_t phy_intf;
+ int err;
+
+ /* Default to RGMII. It's a gigabit part after all */
+ err = of_get_phy_mode(np, &phy_intf);
+ if (err)
+ phy_intf = PHY_INTERFACE_MODE_RGMII;
+
+ /* Aspeed only supports these. I don't know about other IP
+ * block vendors so I'm going to just let them through for
+ * now. Note that this is only a warning if for some obscure
+ * reason the DT really means to lie about it or it's a newer
+ * part we don't know about.
+ *
+ * On the Aspeed SoC there are additionally straps and SCU
+ * control bits that could tell us what the interface is
+ * (or allow us to configure it while the IP block is held
+ * in reset). For now I chose to keep this driver away from
+ * those SoC specific bits and assume the device-tree is
+ * right and the SCU has been configured properly by pinmux
+ * or the firmware.
+ */
+ if (priv->is_aspeed && !(phy_interface_mode_is_rgmii(phy_intf))) {
+ netdev_warn(netdev,
+ "Unsupported PHY mode %s !\n",
+ phy_modes(phy_intf));
+ }
phydev = phy_find_first(priv->mii_bus);
if (!phydev) {
@@ -1056,7 +1085,7 @@ static int ftgmac100_mii_probe(struct ftgmac100 *priv, phy_interface_t intf)
}
phydev = phy_connect(netdev, phydev_name(phydev),
- &ftgmac100_adjust_link, intf);
+ &ftgmac100_adjust_link, phy_intf);
if (IS_ERR(phydev)) {
netdev_err(netdev, "%s: Could not attach to PHY\n", netdev->name);
@@ -1601,7 +1630,6 @@ static int ftgmac100_setup_mdio(struct net_device *netdev)
{
struct ftgmac100 *priv = netdev_priv(netdev);
struct platform_device *pdev = to_platform_device(priv->dev);
- phy_interface_t phy_intf = PHY_INTERFACE_MODE_RGMII;
struct device_node *np = pdev->dev.of_node;
int i, err = 0;
u32 reg;
@@ -1623,39 +1651,6 @@ static int ftgmac100_setup_mdio(struct net_device *netdev)
iowrite32(reg, priv->base + FTGMAC100_OFFSET_REVR);
}
- /* Get PHY mode from device-tree */
- if (np) {
- /* Default to RGMII. It's a gigabit part after all */
- err = of_get_phy_mode(np, &phy_intf);
- if (err)
- phy_intf = PHY_INTERFACE_MODE_RGMII;
-
- /* Aspeed only supports these. I don't know about other IP
- * block vendors so I'm going to just let them through for
- * now. Note that this is only a warning if for some obscure
- * reason the DT really means to lie about it or it's a newer
- * part we don't know about.
- *
- * On the Aspeed SoC there are additionally straps and SCU
- * control bits that could tell us what the interface is
- * (or allow us to configure it while the IP block is held
- * in reset). For now I chose to keep this driver away from
- * those SoC specific bits and assume the device-tree is
- * right and the SCU has been configured properly by pinmux
- * or the firmware.
- */
- if (priv->is_aspeed &&
- phy_intf != PHY_INTERFACE_MODE_RMII &&
- phy_intf != PHY_INTERFACE_MODE_RGMII &&
- phy_intf != PHY_INTERFACE_MODE_RGMII_ID &&
- phy_intf != PHY_INTERFACE_MODE_RGMII_RXID &&
- phy_intf != PHY_INTERFACE_MODE_RGMII_TXID) {
- netdev_warn(netdev,
- "Unsupported PHY mode %s !\n",
- phy_modes(phy_intf));
- }
- }
-
priv->mii_bus->name = "ftgmac100_mdio";
snprintf(priv->mii_bus->id, MII_BUS_ID_SIZE, "%s-%d",
pdev->name, pdev->id);
@@ -1673,29 +1668,28 @@ static int ftgmac100_setup_mdio(struct net_device *netdev)
goto err_register_mdiobus;
}
- err = ftgmac100_mii_probe(priv, phy_intf);
- if (err) {
- dev_err(priv->dev, "MII Probe failed!\n");
- goto err_mii_probe;
- }
-
return 0;
-err_mii_probe:
- mdiobus_unregister(priv->mii_bus);
err_register_mdiobus:
mdiobus_free(priv->mii_bus);
return err;
}
+static void ftgmac100_phy_disconnect(struct net_device *netdev)
+{
+ if (!netdev->phydev)
+ return;
+
+ phy_disconnect(netdev->phydev);
+}
+
static void ftgmac100_destroy_mdio(struct net_device *netdev)
{
struct ftgmac100 *priv = netdev_priv(netdev);
- if (!netdev->phydev)
+ if (!priv->mii_bus)
return;
- phy_disconnect(netdev->phydev);
mdiobus_unregister(priv->mii_bus);
mdiobus_free(priv->mii_bus);
}
@@ -1825,14 +1819,14 @@ static int ftgmac100_probe(struct platform_device *pdev)
if (np && of_get_property(np, "use-ncsi", NULL)) {
if (!IS_ENABLED(CONFIG_NET_NCSI)) {
dev_err(&pdev->dev, "NCSI stack not enabled\n");
- goto err_ncsi_dev;
+ goto err_phy_connect;
}
dev_info(&pdev->dev, "Using NCSI interface\n");
priv->use_ncsi = true;
priv->ndev = ncsi_register_dev(netdev, ftgmac100_ncsi_handler);
if (!priv->ndev)
- goto err_ncsi_dev;
+ goto err_phy_connect;
} else if (np && of_get_property(np, "phy-handle", NULL)) {
struct phy_device *phy;
@@ -1860,12 +1854,19 @@ static int ftgmac100_probe(struct platform_device *pdev)
err = ftgmac100_setup_mdio(netdev);
if (err)
goto err_setup_mdio;
+
+ err = ftgmac100_mii_probe(netdev);
+ if (err) {
+ dev_err(priv->dev, "MII probe failed!\n");
+ goto err_ncsi_dev;
+ }
+
}
if (priv->is_aspeed) {
err = ftgmac100_setup_clk(priv);
if (err)
- goto err_ncsi_dev;
+ goto err_phy_connect;
}
/* Default ring sizes */
@@ -1901,6 +1902,8 @@ static int ftgmac100_probe(struct platform_device *pdev)
err_register_netdev:
clk_disable_unprepare(priv->rclk);
clk_disable_unprepare(priv->clk);
+err_phy_connect:
+ ftgmac100_phy_disconnect(netdev);
err_ncsi_dev:
ftgmac100_destroy_mdio(netdev);
err_setup_mdio:
@@ -1931,6 +1934,7 @@ static int ftgmac100_remove(struct platform_device *pdev)
*/
cancel_work_sync(&priv->reset_task);
+ ftgmac100_phy_disconnect(netdev);
ftgmac100_destroy_mdio(netdev);
iounmap(priv->base);
Split MDIO registration and PHY connect into ftgmac100_setup_mdio and ftgmac100_mii_probe. Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com> --- drivers/net/ethernet/faraday/ftgmac100.c | 104 ++++++++++++----------- 1 file changed, 54 insertions(+), 50 deletions(-)