@@ -1312,13 +1312,33 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
const struct ethtool_link_ksettings *kset)
{
__ETHTOOL_DECLARE_LINK_MODE_MASK(support);
- struct ethtool_link_ksettings our_kset;
struct phylink_link_state config;
const struct phy_setting *s;
- int ret;
ASSERT_RTNL();
+ if (pl->phydev) {
+ /* We can rely on phylib for this update; we also do not need
+ * to update the pl->link_config settings:
+ * - the configuration returned via ksettings_get() will come
+ * from phylib whenever a PHY is present.
+ * - link_config.interface will be updated by the PHY calling
+ * back via phylink_phy_change() and a subsequent resolve.
+ * - initial link configuration for PHY mode comes from the
+ * last phy state updated via phylink_phy_change().
+ * - other configuration changes (e.g. pause modes) are
+ * performed directly via phylib.
+ * - if in in-band mode with a PHY, the link configuration
+ * is passed on the link from the PHY, and all of
+ * link_config.{speed,duplex,an_enabled,pause} are not used.
+ * - the only possible use would be link_config.advertising
+ * pause modes when in 1000base-X mode with a PHY, but in
+ * the presence of a PHY, this should not be changed as that
+ * should be determined from the media side advertisement.
+ */
+ return phy_ethtool_ksettings_set(pl->phydev, kset);
+ }
+
linkmode_copy(support, pl->supported);
config = pl->link_config;
config.an_enabled = kset->base.autoneg == AUTONEG_ENABLE;
@@ -1365,65 +1385,35 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
return -EINVAL;
}
- if (pl->phydev) {
- /* If we have a PHY, we process the kset change via phylib.
- * phylib will call our link state function if the PHY
- * parameters have changed, which will trigger a resolve
- * and update the MAC configuration.
- */
- our_kset = *kset;
- linkmode_copy(our_kset.link_modes.advertising,
- config.advertising);
- our_kset.base.speed = config.speed;
- our_kset.base.duplex = config.duplex;
+ /* For a fixed link, this isn't able to change any parameters,
+ * which just leaves inband mode.
+ */
+ if (phylink_validate(pl, support, &config))
+ return -EINVAL;
- ret = phy_ethtool_ksettings_set(pl->phydev, &our_kset);
- if (ret)
- return ret;
+ /* If autonegotiation is enabled, we must have an advertisement */
+ if (config.an_enabled && phylink_is_empty_linkmode(config.advertising))
+ return -EINVAL;
- mutex_lock(&pl->state_mutex);
- /* Save the new configuration */
- linkmode_copy(pl->link_config.advertising,
- our_kset.link_modes.advertising);
- pl->link_config.interface = config.interface;
- pl->link_config.speed = our_kset.base.speed;
- pl->link_config.duplex = our_kset.base.duplex;
- pl->link_config.an_enabled = our_kset.base.autoneg !=
- AUTONEG_DISABLE;
- mutex_unlock(&pl->state_mutex);
- } else {
- /* For a fixed link, this isn't able to change any parameters,
- * which just leaves inband mode.
+ mutex_lock(&pl->state_mutex);
+ linkmode_copy(pl->link_config.advertising, config.advertising);
+ pl->link_config.interface = config.interface;
+ pl->link_config.speed = config.speed;
+ pl->link_config.duplex = config.duplex;
+ pl->link_config.an_enabled = kset->base.autoneg !=
+ AUTONEG_DISABLE;
+
+ if (pl->cur_link_an_mode == MLO_AN_INBAND &&
+ !test_bit(PHYLINK_DISABLE_STOPPED, &pl->phylink_disable_state)) {
+ /* If in 802.3z mode, this updates the advertisement.
+ *
+ * If we are in SGMII mode without a PHY, there is no
+ * advertisement; the only thing we have is the pause
+ * modes which can only come from a PHY.
*/
- if (phylink_validate(pl, support, &config))
- return -EINVAL;
-
- /* If autonegotiation is enabled, we must have an advertisement */
- if (config.an_enabled &&
- phylink_is_empty_linkmode(config.advertising))
- return -EINVAL;
-
- mutex_lock(&pl->state_mutex);
- linkmode_copy(pl->link_config.advertising, config.advertising);
- pl->link_config.interface = config.interface;
- pl->link_config.speed = config.speed;
- pl->link_config.duplex = config.duplex;
- pl->link_config.an_enabled = kset->base.autoneg !=
- AUTONEG_DISABLE;
-
- if (pl->cur_link_an_mode == MLO_AN_INBAND &&
- !test_bit(PHYLINK_DISABLE_STOPPED,
- &pl->phylink_disable_state)) {
- /* If in 802.3z mode, this updates the advertisement.
- *
- * If we are in SGMII mode without a PHY, there is no
- * advertisement; the only thing we have is the pause
- * modes which can only come from a PHY.
- */
- phylink_pcs_config(pl, true, &pl->link_config);
- }
- mutex_unlock(&pl->state_mutex);
+ phylink_pcs_config(pl, true, &pl->link_config);
}
+ mutex_unlock(&pl->state_mutex);
return 0;
}