@@ -155,10 +155,20 @@ static const enum gpiod_flags gpio_flags[] = {
GPIOD_ASIS,
};
-#define T_WAIT msecs_to_jiffies(50)
-#define T_INIT_JIFFIES msecs_to_jiffies(300)
-#define T_RESET_US 10
-#define T_FAULT_RECOVER msecs_to_jiffies(1000)
+/* t_start_up (SFF-8431) or t_init (SFF-8472) is the time required for a
+ * non-cooled module to initialise its laser safety circuitry. We wait
+ * an initial T_WAIT period before we check the tx fault to give any PHY
+ * on board (for a copper SFP) time to initialise.
+ */
+#define T_WAIT msecs_to_jiffies(50)
+#define T_START_UP msecs_to_jiffies(300)
+#define T_START_UP_BAD_GPON msecs_to_jiffies(60000)
+
+/* t_reset is the time required to assert the TX_DISABLE signal to reset
+ * an indicated TX_FAULT.
+ */
+#define T_RESET_US 10
+#define T_FAULT_RECOVER msecs_to_jiffies(1000)
/* SFP module presence detection is poor: the three MOD DEF signals are
* the same length on the PCB, which means it's possible for MOD DEF 0 to
@@ -218,6 +228,7 @@ struct sfp {
struct sfp_eeprom_id id;
unsigned int module_power_mW;
+ unsigned int module_t_start_up;
#if IS_ENABLED(CONFIG_HWMON)
struct sfp_diag diag;
@@ -1655,6 +1666,12 @@ static int sfp_sm_mod_probe(struct sfp *sfp, bool report)
if (ret < 0)
return ret;
+ if (!memcmp(id.base.vendor_name, "ALCATELLUCENT ", 16) &&
+ !memcmp(id.base.vendor_pn, "3FE46541AA ", 16))
+ sfp->module_t_start_up = T_START_UP_BAD_GPON;
+ else
+ sfp->module_t_start_up = T_START_UP;
+
return 0;
}
@@ -1855,11 +1872,12 @@ static void sfp_sm_main(struct sfp *sfp, unsigned int event)
break;
if (sfp->state & SFP_F_TX_FAULT) {
- /* Wait t_init before indicating that the link is up,
- * provided the current state indicates no TX_FAULT. If
- * TX_FAULT clears before this time, that's fine too.
+ /* Wait up to t_init (SFF-8472) or t_start_up (SFF-8431)
+ * from the TX_DISABLE deassertion for the module to
+ * initialise, which is indicated by TX_FAULT
+ * deasserting.
*/
- timeout = T_INIT_JIFFIES;
+ timeout = sfp->module_t_start_up;
if (timeout > T_WAIT)
timeout -= T_WAIT;
else
@@ -1876,8 +1894,8 @@ static void sfp_sm_main(struct sfp *sfp, unsigned int event)
case SFP_S_INIT:
if (event == SFP_E_TIMEOUT && sfp->state & SFP_F_TX_FAULT) {
- /* TX_FAULT is still asserted after t_init, so assume
- * there is a fault.
+ /* TX_FAULT is still asserted after t_init or
+ * or t_start_up, so assume there is a fault.
*/
sfp_sm_fault(sfp, SFP_S_INIT_TX_FAULT,
sfp->sm_retries == 5);
@@ -1896,7 +1914,7 @@ static void sfp_sm_main(struct sfp *sfp, unsigned int event)
case SFP_S_INIT_TX_FAULT:
if (event == SFP_E_TIMEOUT) {
sfp_module_tx_fault_reset(sfp);
- sfp_sm_next(sfp, SFP_S_INIT, T_INIT_JIFFIES);
+ sfp_sm_next(sfp, SFP_S_INIT, sfp->module_t_start_up);
}
break;
@@ -1920,7 +1938,7 @@ static void sfp_sm_main(struct sfp *sfp, unsigned int event)
case SFP_S_TX_FAULT:
if (event == SFP_E_TIMEOUT) {
sfp_module_tx_fault_reset(sfp);
- sfp_sm_next(sfp, SFP_S_REINIT, T_INIT_JIFFIES);
+ sfp_sm_next(sfp, SFP_S_REINIT, sfp->module_t_start_up);
}
break;
The Nokia GPON module can hold tx-fault active while it is initialising which can take up to 60s. Avoid this causing the module to be declared faulty after the SFP MSA defined non-cooled module timeout. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> --- Unfortunately, this adds a second quirk in the SFP code; the SFP code has no access to the bus-layer quirk system, which is currently a good thing as doing so would unnecessarily complicate the code. The bus layer quirk system is about determining the ethtool properties for modules - these quirks are about getting the module's basic functionality up and running. drivers/net/phy/sfp.c | 42 ++++++++++++++++++++++++++++++------------ 1 file changed, 30 insertions(+), 12 deletions(-)