@@ -323,13 +323,73 @@ ipa_endpoint_program_delay(struct ipa_endpoint *endpoint, bool enable)
(void)ipa_endpoint_init_ctrl(endpoint, enable);
}
-/* Returns previous suspend state (true means it was enabled) */
+static bool ipa_endpoint_aggr_active(struct ipa_endpoint *endpoint)
+{
+ u32 mask = BIT(endpoint->endpoint_id);
+ struct ipa *ipa = endpoint->ipa;
+ u32 offset;
+ u32 val;
+
+ /* assert(mask & ipa->available); */
+ offset = ipa_reg_state_aggr_active_offset(ipa->version);
+ val = ioread32(ipa->reg_virt + offset);
+
+ return !!(val & mask);
+}
+
+static void ipa_endpoint_force_close(struct ipa_endpoint *endpoint)
+{
+ u32 mask = BIT(endpoint->endpoint_id);
+ struct ipa *ipa = endpoint->ipa;
+
+ /* assert(mask & ipa->available); */
+ iowrite32(mask, ipa->reg_virt + IPA_REG_AGGR_FORCE_CLOSE_OFFSET);
+}
+
+/**
+ * ipa_endpoint_suspend_aggr() - Emulate suspend interrupt
+ * @endpoint_id: Endpoint on which to emulate a suspend
+ *
+ * Emulate suspend IPA interrupt to unsuspend an endpoint suspended
+ * with an open aggregation frame. This is to work around a hardware
+ * issue in IPA version 3.5.1 where the suspend interrupt will not be
+ * generated when it should be.
+ */
+static void ipa_endpoint_suspend_aggr(struct ipa_endpoint *endpoint)
+{
+ struct ipa *ipa = endpoint->ipa;
+
+ if (!endpoint->data->aggregation)
+ return;
+
+ /* Nothing to do if the endpoint doesn't have aggregation open */
+ if (!ipa_endpoint_aggr_active(endpoint))
+ return;
+
+ /* Force close aggregation */
+ ipa_endpoint_force_close(endpoint);
+
+ ipa_interrupt_simulate_suspend(ipa->interrupt);
+}
+
+/* Returns previous suspend state (true means suspend was enabled) */
static bool
ipa_endpoint_program_suspend(struct ipa_endpoint *endpoint, bool enable)
{
+ bool suspended;
+
/* assert(!endpoint->toward_ipa); */
- return ipa_endpoint_init_ctrl(endpoint, enable);
+ suspended = ipa_endpoint_init_ctrl(endpoint, enable);
+
+ /* A client suspended with an open aggregation frame will not
+ * generate a SUSPEND IPA interrupt. If enabling suspend, have
+ * ipa_endpoint_suspend_aggr() handle this.
+ */
+ if (enable && !suspended)
+ ipa_endpoint_suspend_aggr(endpoint);
+
+ return suspended;
}
/* Enable or disable delay or suspend mode on all modem endpoints */
@@ -1144,29 +1204,6 @@ void ipa_endpoint_default_route_clear(struct ipa *ipa)
ipa_endpoint_default_route_set(ipa, 0);
}
-static bool ipa_endpoint_aggr_active(struct ipa_endpoint *endpoint)
-{
- u32 mask = BIT(endpoint->endpoint_id);
- struct ipa *ipa = endpoint->ipa;
- u32 offset;
- u32 val;
-
- /* assert(mask & ipa->available); */
- offset = ipa_reg_state_aggr_active_offset(ipa->version);
- val = ioread32(ipa->reg_virt + offset);
-
- return !!(val & mask);
-}
-
-static void ipa_endpoint_force_close(struct ipa_endpoint *endpoint)
-{
- u32 mask = BIT(endpoint->endpoint_id);
- struct ipa *ipa = endpoint->ipa;
-
- /* assert(mask & ipa->available); */
- iowrite32(mask, ipa->reg_virt + IPA_REG_AGGR_FORCE_CLOSE_OFFSET);
-}
-
/**
* ipa_endpoint_reset_rx_aggr() - Reset RX endpoint with aggregation active
* @endpoint: Endpoint to be reset
@@ -1366,34 +1403,6 @@ void ipa_endpoint_disable_one(struct ipa_endpoint *endpoint)
endpoint->endpoint_id);
}
-/**
- * ipa_endpoint_suspend_aggr() - Emulate suspend interrupt
- * @endpoint_id: Endpoint on which to emulate a suspend
- *
- * Emulate suspend IPA interrupt to unsuspend an endpoint suspended
- * with an open aggregation frame. This is to work around a hardware
- * issue in IPA version 3.5.1 where the suspend interrupt will not be
- * generated when it should be.
- */
-static void ipa_endpoint_suspend_aggr(struct ipa_endpoint *endpoint)
-{
- struct ipa *ipa = endpoint->ipa;
-
- /* assert(ipa->version == IPA_VERSION_3_5_1); */
-
- if (!endpoint->data->aggregation)
- return;
-
- /* Nothing to do if the endpoint doesn't have aggregation open */
- if (!ipa_endpoint_aggr_active(endpoint))
- return;
-
- /* Force close aggregation */
- ipa_endpoint_force_close(endpoint);
-
- ipa_interrupt_simulate_suspend(ipa->interrupt);
-}
-
void ipa_endpoint_suspend_one(struct ipa_endpoint *endpoint)
{
struct device *dev = &endpoint->ipa->pdev->dev;
@@ -1409,16 +1418,8 @@ void ipa_endpoint_suspend_one(struct ipa_endpoint *endpoint)
/* IPA v3.5.1 doesn't use channel stop for suspend */
stop_channel = endpoint->ipa->version != IPA_VERSION_3_5_1;
- if (!endpoint->toward_ipa && !stop_channel) {
- /* Due to a hardware bug, a client suspended with an open
- * aggregation frame will not generate a SUSPEND IPA
- * interrupt. We work around this by force-closing the
- * aggregation frame, then simulating the arrival of such
- * an interrupt.
- */
+ if (!endpoint->toward_ipa && !stop_channel)
(void)ipa_endpoint_program_suspend(endpoint, true);
- ipa_endpoint_suspend_aggr(endpoint);
- }
ret = gsi_channel_suspend(gsi, endpoint->channel_id, stop_channel);
if (ret)
IPA version 3.5.1 has a hardware quirk that requires special handling if an RX endpoint is suspended while aggregation is active. This handling is implemented by ipa_endpoint_suspend_aggr(). Have ipa_endpoint_program_suspend() be responsible for calling ipa_endpoint_suspend_aggr() if suspend mode is being enabled on an endpoint. If the endpoint does not support aggregation, or if aggregation isn't active, this call will continue to have no effect. Move the definition of ipa_endpoint_suspend_aggr() up in the file so its definition precedes the new earlier reference to it. This requires ipa_endpoint_aggr_active() and ipa_endpoint_force_close() to be moved as well. Signed-off-by: Alex Elder <elder@linaro.org> --- drivers/net/ipa/ipa_endpoint.c | 125 +++++++++++++++++---------------- 1 file changed, 63 insertions(+), 62 deletions(-)