@@ -259,10 +259,15 @@ struct ethtool_tunable {
#define ETHTOOL_PHY_FAST_LINK_DOWN_ON 0
#define ETHTOOL_PHY_FAST_LINK_DOWN_OFF 0xff
+#define ETHTOOL_PHY_EDPD_DFLT_TX_INTERVAL 0x7fff
+#define ETHTOOL_PHY_EDPD_NO_TX 0x8000
+#define ETHTOOL_PHY_EDPD_DISABLE 0
+
enum phy_tunable_id {
ETHTOOL_PHY_ID_UNSPEC,
ETHTOOL_PHY_DOWNSHIFT,
ETHTOOL_PHY_FAST_LINK_DOWN,
+ ETHTOOL_PHY_EDPD,
/*
* Add your fresh new phy tunable attribute above and remember to update
* phy_tunable_strings[] in net/core/ethtool.c
@@ -133,6 +133,7 @@ phy_tunable_strings[__ETHTOOL_PHY_TUNABLE_COUNT][ETH_GSTRING_LEN] = {
[ETHTOOL_ID_UNSPEC] = "Unspec",
[ETHTOOL_PHY_DOWNSHIFT] = "phy-downshift",
[ETHTOOL_PHY_FAST_LINK_DOWN] = "phy-fast-link-down",
+ [ETHTOOL_PHY_EDPD] = "phy-energy-detect-power-down",
};
static int ethtool_get_features(struct net_device *dev, void __user *useraddr)
@@ -2451,6 +2452,11 @@ static int ethtool_phy_tunable_valid(const struct ethtool_tunable *tuna)
tuna->type_id != ETHTOOL_TUNABLE_U8)
return -EINVAL;
break;
+ case ETHTOOL_PHY_EDPD:
+ if (tuna->len != sizeof(u16) ||
+ tuna->type_id != ETHTOOL_TUNABLE_U16)
+ return -EINVAL;
+ break;
default:
return -EINVAL;
}
The `phy_tunable_id` has been named `ETHTOOL_PHY_EDPD` since it looks like this feature is common across other PHYs (like EEE), and defining `ETHTOOL_PHY_ENERGY_DETECT_POWER_DOWN` seems too long. The way EDPD works, is that the RX block is put to a lower power mode, except for link-pulse detection circuits. The TX block is also put to low power mode, but the PHY wakes-up periodically to send link pulses, to avoid lock-ups in case the other side is also in EDPD mode. Currently, there are 2 PHY drivers that look like they could use this new PHY tunable feature: the `adin` && `micrel` PHYs. The ADIN's datasheet mentions that TX pulses are at intervals of 1 second default each, and they can be disabled. For the Micrel KSZ9031 PHY, the datasheet does not mention whether they can be disabled, but mentions that they can modified. The way this change is structured, is similar to the PHY tunable downshift control: * a `ETHTOOL_PHY_EDPD_DFLT_TX_INTERVAL` value is exposed to cover a default TX interval; some PHYs could specify a certain value that makes sense * `ETHTOOL_PHY_EDPD_NO_TX` would disable TX when EDPD is enabled * `ETHTOOL_PHY_EDPD_DISABLE` will disable EDPD This should allow PHYs to: * enable EDPD and not enable TX pulses (interval would be 0) * enable EDPD and configure TX pulse interval; note that TX interval units would be PHY specific; we could consider `seconds` as units, but it could happen that some PHYs would be prefer 500 milliseconds as a unit; a maximum of 32766 units should be sufficient * disable EDPD Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> --- include/uapi/linux/ethtool.h | 5 +++++ net/core/ethtool.c | 6 ++++++ 2 files changed, 11 insertions(+)