| Message ID | 20190610163736.6187-4-martin.blumenstingl@googlemail.com |
|---|---|
| State | Not Applicable |
| Delegated to: | David Miller |
| Headers | show |
| Series | Ethernet PHY reset GPIO updates for Amlogic SoCs | expand |
Hi Martin, On 10/06/2019 17:37, Martin Blumenstingl wrote: > The snps,reset-gpio bindings are deprecated in favour of the generic > "Ethernet PHY reset" bindings. > > Replace snps,reset-gpio from the ðmac node with reset-gpios in the > ethernet-phy node. The old snps,reset-active-low property is now encoded > directly as GPIO flag inside the reset-gpios property. > > snps,reset-delays-us is converted to reset-assert-us and > reset-deassert-us. reset-assert-us is the second cell from > snps,reset-delays-us while reset-deassert-us was the third cell. > > Instead of blindly copying the old values (which seems strange since > they gave the PHY one second to come out of reset) over this also > updates the delays based on the datasheets: > - the Realtek RTL8211F PHY needs a 10ms delay (this applies to the > following boards: GXBB NanoPi K2, GXBB Odroid-C2, GXBB Vega S95 > variants, GXBB Wetek variants, GXL P230, GXM Khadas VIM2, GXM Nexbox > A1, GXM Q200, GXM RBox Pro) From the datasheets I've seen, RTL8211E/F specify an assert delay of 10ms, but a deassert delay of 30ms. Robin. > - the ICPlus IP101GR PHY needs a 2.5ms delay (this applies to the GXBB > Nexbox A95X) > - the Micrel KSZ9031 seems to require a 100us delay but use the same > (seemingly safe) values from RTL8211F due to lack of a board to verify > this (this appleis to the GXBB P200) > > The GXBB P201 board is left out from this conversion because it doesn't > have a dedicated PHY node (because it's not clear which PHY is used on > that board). > > Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> > --- > arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts | 9 +++++---- > .../arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 8 ++++---- > arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 9 +++++---- > arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts | 9 +++++---- > arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi | 9 +++++---- > arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi | 8 ++++---- > arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts | 11 ++++++----- > arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts | 10 +++++----- > arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 8 ++++---- > arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts | 11 ++++++----- > arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts | 8 ++++---- > 11 files changed, 53 insertions(+), 47 deletions(-) > > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts > index 849c01650c4d..32e901538519 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts > +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts > @@ -154,10 +154,6 @@ > > amlogic,tx-delay-ns = <2>; > > - snps,reset-gpio = <&gpio GPIOZ_14 0>; > - snps,reset-delays-us = <0 10000 1000000>; > - snps,reset-active-low; > - > mdio { > compatible = "snps,dwmac-mdio"; > #address-cells = <1>; > @@ -166,6 +162,11 @@ > eth_phy0: ethernet-phy@0 { > /* Realtek RTL8211F (0x001cc916) */ > reg = <0>; > + > + reset-assert-us = <10000>; > + reset-deassert-us = <10000>; > + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; > + > interrupt-parent = <&gpio_intc>; > /* MAC_INTR on GPIOZ_15 */ > interrupts = <29 IRQ_TYPE_LEVEL_LOW>; > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts > index 3c54f26eef15..c2f619a6a96c 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts > +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts > @@ -162,10 +162,6 @@ > phy-handle = <ð_phy0>; > phy-mode = "rmii"; > > - snps,reset-gpio = <&gpio GPIOZ_14 0>; > - snps,reset-delays-us = <0 10000 1000000>; > - snps,reset-active-low; > - > mdio { > compatible = "snps,dwmac-mdio"; > #address-cells = <1>; > @@ -174,6 +170,10 @@ > eth_phy0: ethernet-phy@0 { > /* IC Plus IP101GR (0x02430c54) */ > reg = <0>; > + > + reset-assert-us = <2500>; > + reset-deassert-us = <2500>; > + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; > }; > }; > }; > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts > index 5a139e7b1c60..fc0528a89b6c 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts > +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts > @@ -126,10 +126,6 @@ > phy-handle = <ð_phy0>; > phy-mode = "rgmii"; > > - snps,reset-gpio = <&gpio GPIOZ_14 0>; > - snps,reset-delays-us = <0 10000 1000000>; > - snps,reset-active-low; > - > amlogic,tx-delay-ns = <2>; > > mdio { > @@ -140,6 +136,11 @@ > eth_phy0: ethernet-phy@0 { > /* Realtek RTL8211F (0x001cc916) */ > reg = <0>; > + > + reset-assert-us = <10000>; > + reset-deassert-us = <10000>; > + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; > + > interrupt-parent = <&gpio_intc>; > /* MAC_INTR on GPIOZ_15 */ > interrupts = <29 IRQ_TYPE_LEVEL_LOW>; > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts > index 9d2406a7c4fa..eeea17767cab 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts > +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts > @@ -68,10 +68,6 @@ > > amlogic,tx-delay-ns = <2>; > > - snps,reset-gpio = <&gpio GPIOZ_14 0>; > - snps,reset-delays-us = <0 10000 1000000>; > - snps,reset-active-low; > - > mdio { > compatible = "snps,dwmac-mdio"; > #address-cells = <1>; > @@ -80,6 +76,11 @@ > eth_phy0: ethernet-phy@3 { > /* Micrel KSZ9031 (0x00221620) */ > reg = <3>; > + > + reset-assert-us = <10000>; > + reset-deassert-us = <10000>; > + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; > + > interrupt-parent = <&gpio_intc>; > /* MAC_INTR on GPIOZ_15 */ > interrupts = <29 IRQ_TYPE_LEVEL_LOW>; > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi > index 18856f28fd60..a7c2d8bfdd0b 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi > +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi > @@ -116,10 +116,6 @@ > > amlogic,tx-delay-ns = <2>; > > - snps,reset-gpio = <&gpio GPIOZ_14 0>; > - snps,reset-delays-us = <0 10000 1000000>; > - snps,reset-active-low; > - > mdio { > compatible = "snps,dwmac-mdio"; > #address-cells = <1>; > @@ -128,6 +124,11 @@ > eth_phy0: ethernet-phy@0 { > /* Realtek RTL8211F (0x001cc916) */ > reg = <0>; > + > + reset-assert-us = <10000>; > + reset-deassert-us = <10000>; > + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; > + > interrupt-parent = <&gpio_intc>; > /* MAC_INTR on GPIOZ_15 */ > interrupts = <29 IRQ_TYPE_LEVEL_LOW>; > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi > index 9ef6858779c1..dc0d8c3b4eff 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi > +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi > @@ -137,10 +137,6 @@ > > amlogic,tx-delay-ns = <2>; > > - snps,reset-gpio = <&gpio GPIOZ_14 0>; > - snps,reset-delays-us = <0 10000 1000000>; > - snps,reset-active-low; > - > mdio { > compatible = "snps,dwmac-mdio"; > #address-cells = <1>; > @@ -149,6 +145,10 @@ > eth_phy0: ethernet-phy@0 { > /* Realtek RTL8211F (0x001cc916) */ > reg = <0>; > + > + reset-assert-us = <10000>; > + reset-deassert-us = <10000>; > + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; > }; > }; > }; > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts > index 767b1763a612..003d6aa6964c 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts > +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts > @@ -70,11 +70,6 @@ > > amlogic,tx-delay-ns = <2>; > > - /* External PHY reset is shared with internal PHY Led signals */ > - snps,reset-gpio = <&gpio GPIOZ_14 0>; > - snps,reset-delays-us = <0 10000 1000000>; > - snps,reset-active-low; > - > /* External PHY is in RGMII */ > phy-mode = "rgmii"; > }; > @@ -84,6 +79,12 @@ > /* Realtek RTL8211F (0x001cc916) */ > reg = <0>; > max-speed = <1000>; > + > + /* External PHY reset is shared with internal PHY Led signal */ > + reset-assert-us = <10000>; > + reset-deassert-us = <10000>; > + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; > + > interrupt-parent = <&gpio_intc>; > interrupts = <29 IRQ_TYPE_LEVEL_LOW>; > eee-broken-1000t; > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts > index ff4f0780824d..2b6003b605a4 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts > +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts > @@ -239,11 +239,6 @@ > > amlogic,tx-delay-ns = <2>; > > - /* External PHY reset is shared with internal PHY Led signals */ > - snps,reset-gpio = <&gpio GPIOZ_14 0>; > - snps,reset-delays-us = <0 10000 1000000>; > - snps,reset-active-low; > - > /* External PHY is in RGMII */ > phy-mode = "rgmii"; > > @@ -254,6 +249,11 @@ > external_phy: ethernet-phy@0 { > /* Realtek RTL8211F (0x001cc916) */ > reg = <0>; > + > + reset-assert-us = <10000>; > + reset-deassert-us = <10000>; > + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; > + > interrupt-parent = <&gpio_intc>; > /* MAC_INTR on GPIOZ_15 */ > interrupts = <25 IRQ_TYPE_LEVEL_LOW>; > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts > index 29715eae14a9..a2a7ec5c8fd6 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts > +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts > @@ -101,10 +101,6 @@ > > amlogic,tx-delay-ns = <2>; > > - snps,reset-gpio = <&gpio GPIOZ_14 0>; > - snps,reset-delays-us = <0 10000 1000000>; > - snps,reset-active-low; > - > /* External PHY is in RGMII */ > phy-mode = "rgmii"; > }; > @@ -114,6 +110,10 @@ > /* Realtek RTL8211F (0x001cc916) */ > reg = <0>; > max-speed = <1000>; > + > + reset-assert-us = <10000>; > + reset-deassert-us = <10000>; > + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; > }; > }; > > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts > index 8939c0fc5b62..044668228ece 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts > +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts > @@ -52,11 +52,6 @@ > > amlogic,tx-delay-ns = <2>; > > - /* External PHY reset is shared with internal PHY Led signals */ > - snps,reset-gpio = <&gpio GPIOZ_14 0>; > - snps,reset-delays-us = <0 10000 1000000>; > - snps,reset-active-low; > - > /* External PHY is in RGMII */ > phy-mode = "rgmii"; > }; > @@ -66,6 +61,12 @@ > /* Realtek RTL8211F (0x001cc916) */ > reg = <0>; > max-speed = <1000>; > + > + /* External PHY reset is shared with internal PHY Led signal */ > + reset-assert-us = <10000>; > + reset-deassert-us = <10000>; > + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; > + > interrupt-parent = <&gpio_intc>; > /* MAC_INTR on GPIOZ_15 */ > interrupts = <25 IRQ_TYPE_LEVEL_LOW>; > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts > index 13de1e8f58b5..04eae80585af 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts > +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts > @@ -101,10 +101,6 @@ > /* Select external PHY by default */ > phy-handle = <&external_phy>; > > - snps,reset-gpio = <&gpio GPIOZ_14 0>; > - snps,reset-delays-us = <0 10000 1000000>; > - snps,reset-active-low; > - > amlogic,tx-delay-ns = <2>; > > /* External PHY is in RGMII */ > @@ -116,6 +112,10 @@ > /* Realtek RTL8211F (0x001cc916) */ > reg = <0>; > max-speed = <1000>; > + > + reset-assert-us = <10000>; > + reset-deassert-us = <10000>; > + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; > }; > }; > >
Hi Robin, On Mon, Jun 10, 2019 at 6:54 PM Robin Murphy <robin.murphy@arm.com> wrote: > > Hi Martin, > > On 10/06/2019 17:37, Martin Blumenstingl wrote: > > The snps,reset-gpio bindings are deprecated in favour of the generic > > "Ethernet PHY reset" bindings. > > > > Replace snps,reset-gpio from the ðmac node with reset-gpios in the > > ethernet-phy node. The old snps,reset-active-low property is now encoded > > directly as GPIO flag inside the reset-gpios property. > > > > snps,reset-delays-us is converted to reset-assert-us and > > reset-deassert-us. reset-assert-us is the second cell from > > snps,reset-delays-us while reset-deassert-us was the third cell. > > > > Instead of blindly copying the old values (which seems strange since > > they gave the PHY one second to come out of reset) over this also > > updates the delays based on the datasheets: > > - the Realtek RTL8211F PHY needs a 10ms delay (this applies to the > > following boards: GXBB NanoPi K2, GXBB Odroid-C2, GXBB Vega S95 > > variants, GXBB Wetek variants, GXL P230, GXM Khadas VIM2, GXM Nexbox > > A1, GXM Q200, GXM RBox Pro) > > From the datasheets I've seen, RTL8211E/F specify an assert delay of > 10ms, but a deassert delay of 30ms. thank you for spotting this! I don't have an RTL8211F datasheet, but I now see what you mean based on the RTL8211E datasheet. now that you pointed this out: it seems that I made a similar mistake with the IP101GR PHY The datasheet mentions: "Chip will be able to operate after 2.5ms delay of the rising edge of RESET_N" However, further down in the datasheet it states: "Set low to RESET_N pin, for at least 10ms ..." I'll wait a few days for more comments and then send a fixed version Martin
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts index 849c01650c4d..32e901538519 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts @@ -154,10 +154,6 @@ amlogic,tx-delay-ns = <2>; - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; - mdio { compatible = "snps,dwmac-mdio"; #address-cells = <1>; @@ -166,6 +162,11 @@ eth_phy0: ethernet-phy@0 { /* Realtek RTL8211F (0x001cc916) */ reg = <0>; + + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio_intc>; /* MAC_INTR on GPIOZ_15 */ interrupts = <29 IRQ_TYPE_LEVEL_LOW>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts index 3c54f26eef15..c2f619a6a96c 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts @@ -162,10 +162,6 @@ phy-handle = <ð_phy0>; phy-mode = "rmii"; - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; - mdio { compatible = "snps,dwmac-mdio"; #address-cells = <1>; @@ -174,6 +170,10 @@ eth_phy0: ethernet-phy@0 { /* IC Plus IP101GR (0x02430c54) */ reg = <0>; + + reset-assert-us = <2500>; + reset-deassert-us = <2500>; + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; }; }; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts index 5a139e7b1c60..fc0528a89b6c 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts @@ -126,10 +126,6 @@ phy-handle = <ð_phy0>; phy-mode = "rgmii"; - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; - amlogic,tx-delay-ns = <2>; mdio { @@ -140,6 +136,11 @@ eth_phy0: ethernet-phy@0 { /* Realtek RTL8211F (0x001cc916) */ reg = <0>; + + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio_intc>; /* MAC_INTR on GPIOZ_15 */ interrupts = <29 IRQ_TYPE_LEVEL_LOW>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts index 9d2406a7c4fa..eeea17767cab 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts @@ -68,10 +68,6 @@ amlogic,tx-delay-ns = <2>; - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; - mdio { compatible = "snps,dwmac-mdio"; #address-cells = <1>; @@ -80,6 +76,11 @@ eth_phy0: ethernet-phy@3 { /* Micrel KSZ9031 (0x00221620) */ reg = <3>; + + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio_intc>; /* MAC_INTR on GPIOZ_15 */ interrupts = <29 IRQ_TYPE_LEVEL_LOW>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi index 18856f28fd60..a7c2d8bfdd0b 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi @@ -116,10 +116,6 @@ amlogic,tx-delay-ns = <2>; - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; - mdio { compatible = "snps,dwmac-mdio"; #address-cells = <1>; @@ -128,6 +124,11 @@ eth_phy0: ethernet-phy@0 { /* Realtek RTL8211F (0x001cc916) */ reg = <0>; + + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio_intc>; /* MAC_INTR on GPIOZ_15 */ interrupts = <29 IRQ_TYPE_LEVEL_LOW>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi index 9ef6858779c1..dc0d8c3b4eff 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi @@ -137,10 +137,6 @@ amlogic,tx-delay-ns = <2>; - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; - mdio { compatible = "snps,dwmac-mdio"; #address-cells = <1>; @@ -149,6 +145,10 @@ eth_phy0: ethernet-phy@0 { /* Realtek RTL8211F (0x001cc916) */ reg = <0>; + + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; }; }; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts index 767b1763a612..003d6aa6964c 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts @@ -70,11 +70,6 @@ amlogic,tx-delay-ns = <2>; - /* External PHY reset is shared with internal PHY Led signals */ - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; - /* External PHY is in RGMII */ phy-mode = "rgmii"; }; @@ -84,6 +79,12 @@ /* Realtek RTL8211F (0x001cc916) */ reg = <0>; max-speed = <1000>; + + /* External PHY reset is shared with internal PHY Led signal */ + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio_intc>; interrupts = <29 IRQ_TYPE_LEVEL_LOW>; eee-broken-1000t; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts index ff4f0780824d..2b6003b605a4 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts @@ -239,11 +239,6 @@ amlogic,tx-delay-ns = <2>; - /* External PHY reset is shared with internal PHY Led signals */ - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; - /* External PHY is in RGMII */ phy-mode = "rgmii"; @@ -254,6 +249,11 @@ external_phy: ethernet-phy@0 { /* Realtek RTL8211F (0x001cc916) */ reg = <0>; + + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio_intc>; /* MAC_INTR on GPIOZ_15 */ interrupts = <25 IRQ_TYPE_LEVEL_LOW>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts index 29715eae14a9..a2a7ec5c8fd6 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts @@ -101,10 +101,6 @@ amlogic,tx-delay-ns = <2>; - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; - /* External PHY is in RGMII */ phy-mode = "rgmii"; }; @@ -114,6 +110,10 @@ /* Realtek RTL8211F (0x001cc916) */ reg = <0>; max-speed = <1000>; + + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; }; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts index 8939c0fc5b62..044668228ece 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts @@ -52,11 +52,6 @@ amlogic,tx-delay-ns = <2>; - /* External PHY reset is shared with internal PHY Led signals */ - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; - /* External PHY is in RGMII */ phy-mode = "rgmii"; }; @@ -66,6 +61,12 @@ /* Realtek RTL8211F (0x001cc916) */ reg = <0>; max-speed = <1000>; + + /* External PHY reset is shared with internal PHY Led signal */ + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio_intc>; /* MAC_INTR on GPIOZ_15 */ interrupts = <25 IRQ_TYPE_LEVEL_LOW>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts index 13de1e8f58b5..04eae80585af 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts @@ -101,10 +101,6 @@ /* Select external PHY by default */ phy-handle = <&external_phy>; - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; - amlogic,tx-delay-ns = <2>; /* External PHY is in RGMII */ @@ -116,6 +112,10 @@ /* Realtek RTL8211F (0x001cc916) */ reg = <0>; max-speed = <1000>; + + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; }; };
The snps,reset-gpio bindings are deprecated in favour of the generic "Ethernet PHY reset" bindings. Replace snps,reset-gpio from the ðmac node with reset-gpios in the ethernet-phy node. The old snps,reset-active-low property is now encoded directly as GPIO flag inside the reset-gpios property. snps,reset-delays-us is converted to reset-assert-us and reset-deassert-us. reset-assert-us is the second cell from snps,reset-delays-us while reset-deassert-us was the third cell. Instead of blindly copying the old values (which seems strange since they gave the PHY one second to come out of reset) over this also updates the delays based on the datasheets: - the Realtek RTL8211F PHY needs a 10ms delay (this applies to the following boards: GXBB NanoPi K2, GXBB Odroid-C2, GXBB Vega S95 variants, GXBB Wetek variants, GXL P230, GXM Khadas VIM2, GXM Nexbox A1, GXM Q200, GXM RBox Pro) - the ICPlus IP101GR PHY needs a 2.5ms delay (this applies to the GXBB Nexbox A95X) - the Micrel KSZ9031 seems to require a 100us delay but use the same (seemingly safe) values from RTL8211F due to lack of a board to verify this (this appleis to the GXBB P200) The GXBB P201 board is left out from this conversion because it doesn't have a dedicated PHY node (because it's not clear which PHY is used on that board). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> --- arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts | 9 +++++---- .../arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 8 ++++---- arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 9 +++++---- arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts | 9 +++++---- arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi | 9 +++++---- arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi | 8 ++++---- arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts | 11 ++++++----- arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts | 10 +++++----- arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 8 ++++---- arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts | 11 ++++++----- arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts | 8 ++++---- 11 files changed, 53 insertions(+), 47 deletions(-)