diff mbox series

[v5,2/6] net: stmmac: sun8i: force select external PHY when no internal one

Message ID 20190520235009.16734-3-megous@megous.com
State Changes Requested
Delegated to: David Miller
Headers show
Series Add support for Orange Pi 3 | expand

Commit Message

Ondřej Jirman May 20, 2019, 11:50 p.m. UTC 
From: Icenowy Zheng <icenowy@aosc.io>

The PHY selection bit also exists on SoCs without an internal PHY; if it's
set to 1 (internal PHY, default value) then the MAC will not make use of
any PHY such SoCs.

This problem appears when adapting for H6, which has no real internal PHY
(the "internal PHY" on H6 is not on-die, but on a co-packaged AC200 chip,
connected via RMII interface at GPIO bank A).

Force the PHY selection bit to 0 when the SOC doesn't have an internal PHY,
to address the problem of a wrong default value.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 5 +++++
 1 file changed, 5 insertions(+)

Comments

Sergei Shtylyov May 21, 2019, 9:27 a.m. UTC | #1 
Hello!

On 21.05.2019 2:50, megous@megous.com wrote:

> From: Icenowy Zheng <icenowy@aosc.io>
> 
> The PHY selection bit also exists on SoCs without an internal PHY; if it's
> set to 1 (internal PHY, default value) then the MAC will not make use of
> any PHY such SoCs.
          ^ "on" or "with" missing?

> This problem appears when adapting for H6, which has no real internal PHY
> (the "internal PHY" on H6 is not on-die, but on a co-packaged AC200 chip,
> connected via RMII interface at GPIO bank A).
> 
> Force the PHY selection bit to 0 when the SOC doesn't have an internal PHY,
> to address the problem of a wrong default value.
> 
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Signed-off-by: Ondrej Jirman <megous@megous.com>
[...]

MBR, Sergei
Ondřej Jirman May 21, 2019, 9:56 a.m. UTC | #2 
Hello Sergei,

On Tue, May 21, 2019 at 12:27:24PM +0300, Sergei Shtylyov wrote:
> Hello!
> 
> On 21.05.2019 2:50, megous@megous.com wrote:
> 
> > From: Icenowy Zheng <icenowy@aosc.io>
> > 
> > The PHY selection bit also exists on SoCs without an internal PHY; if it's
> > set to 1 (internal PHY, default value) then the MAC will not make use of
> > any PHY such SoCs.
>          ^ "on" or "with" missing?

It's missing 'on'.

thank you,
	Ondrej

> > This problem appears when adapting for H6, which has no real internal PHY
> > (the "internal PHY" on H6 is not on-die, but on a co-packaged AC200 chip,
> > connected via RMII interface at GPIO bank A).
> > 
> > Force the PHY selection bit to 0 when the SOC doesn't have an internal PHY,
> > to address the problem of a wrong default value.
> > 
> > Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> > Signed-off-by: Ondrej Jirman <megous@megous.com>
> [...]
> 
> MBR, Sergei
diff mbox series

Patch

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
index 3258dec84d55..0484c289f328 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
@@ -907,6 +907,11 @@  static int sun8i_dwmac_set_syscon(struct stmmac_priv *priv)
 		 * address. No need to mask it again.
 		 */
 		reg |= 1 << H3_EPHY_ADDR_SHIFT;
+	} else {
+		/* For SoCs without internal PHY the PHY selection bit should be
+		 * set to 0 (external PHY).
+		 */
+		reg &= ~H3_EPHY_SELECT;
 	}
 
 	if (!of_property_read_u32(node, "allwinner,tx-delay-ps", &val)) {