@@ -255,104 +255,75 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw)
}
/**
- * ixgbe_setup_fc_82598 - Configure flow control settings
+ * ixgbe_fc_enable_82598 - Enable flow control
* @hw: pointer to hardware structure
* @packetbuf_num: packet buffer number (0-7)
*
- * Configures the flow control settings based on SW configuration. This
- * function is used for 802.3x flow control configuration only.
+ * Enable flow control according to the current settings.
**/
-static s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
+static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
{
- u32 frctl_reg;
+ s32 ret_val = 0;
+ u32 fctrl_reg;
u32 rmcs_reg;
+ u32 reg;
- if (packetbuf_num < 0 || packetbuf_num > 7) {
- hw_dbg(hw, "Invalid packet buffer number [%d], expected range is"
- " 0-7\n", packetbuf_num);
- }
-
- frctl_reg = IXGBE_READ_REG(hw, IXGBE_FCTRL);
- frctl_reg &= ~(IXGBE_FCTRL_RFCE | IXGBE_FCTRL_RPFCE);
+ fctrl_reg = IXGBE_READ_REG(hw, IXGBE_FCTRL);
+ fctrl_reg &= ~(IXGBE_FCTRL_RFCE | IXGBE_FCTRL_RPFCE);
rmcs_reg = IXGBE_READ_REG(hw, IXGBE_RMCS);
rmcs_reg &= ~(IXGBE_RMCS_TFCE_PRIORITY | IXGBE_RMCS_TFCE_802_3X);
/*
- * 10 gig parts do not have a word in the EEPROM to determine the
- * default flow control setting, so we explicitly set it to full.
- */
- if (hw->fc.type == ixgbe_fc_default)
- hw->fc.type = ixgbe_fc_full;
-
- /*
- * We want to save off the original Flow Control configuration just in
- * case we get disconnected and then reconnected into a different hub
- * or switch with different Flow Control capabilities.
- */
- hw->fc.original_type = hw->fc.type;
-
- /*
- * The possible values of the "flow_control" parameter are:
+ * The possible values of fc.current_mode are:
* 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause frames but not
- * send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames but we do not
- * support receiving pause frames)
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but
+ * we do not support receiving pause frames).
* 3: Both Rx and Tx flow control (symmetric) are enabled.
* other: Invalid.
*/
- switch (hw->fc.type) {
+ switch (hw->fc.current_mode) {
case ixgbe_fc_none:
+ /* Flow control completely disabled by software override. */
break;
case ixgbe_fc_rx_pause:
/*
- * Rx Flow control is enabled,
- * and Tx Flow control is disabled.
+ * Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
*/
- frctl_reg |= IXGBE_FCTRL_RFCE;
+ fctrl_reg |= IXGBE_FCTRL_RFCE;
break;
case ixgbe_fc_tx_pause:
/*
- * Tx Flow control is enabled, and Rx Flow control is disabled,
- * by a software over-ride.
+ * Tx Flow control is enabled, and Rx Flow control is
+ * disabled by software override.
*/
rmcs_reg |= IXGBE_RMCS_TFCE_802_3X;
break;
case ixgbe_fc_full:
- /*
- * Flow control (both Rx and Tx) is enabled by a software
- * over-ride.
- */
- frctl_reg |= IXGBE_FCTRL_RFCE;
+ /* Flow control (both Rx and Tx) is enabled by SW override. */
+ fctrl_reg |= IXGBE_FCTRL_RFCE;
rmcs_reg |= IXGBE_RMCS_TFCE_802_3X;
break;
default:
- /* We should never get here. The value should be 0-3. */
hw_dbg(hw, "Flow control param set incorrectly\n");
+ ret_val = -IXGBE_ERR_CONFIG;
+ goto out;
break;
}
/* Enable 802.3x based flow control settings. */
- IXGBE_WRITE_REG(hw, IXGBE_FCTRL, frctl_reg);
+ IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl_reg);
IXGBE_WRITE_REG(hw, IXGBE_RMCS, rmcs_reg);
- /*
- * Check for invalid software configuration, zeros are completely
- * invalid for all parameters used past this point, and if we enable
- * flow control with zero water marks, we blast flow control packets.
- */
- if (!hw->fc.low_water || !hw->fc.high_water || !hw->fc.pause_time) {
- hw_dbg(hw, "Flow control structure initialized incorrectly\n");
- return IXGBE_ERR_INVALID_LINK_SETTINGS;
- }
-
- /*
- * We need to set up the Receive Threshold high and low water
- * marks as well as (optionally) enabling the transmission of
- * XON frames.
- */
- if (hw->fc.type & ixgbe_fc_tx_pause) {
+ /* Set up and enable Rx high/low water mark thresholds, enable XON. */
+ if (hw->fc.current_mode & ixgbe_fc_tx_pause) {
if (hw->fc.send_xon) {
IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num),
(hw->fc.low_water | IXGBE_FCRTL_XONE));
@@ -360,14 +331,93 @@ static s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num),
hw->fc.low_water);
}
+
IXGBE_WRITE_REG(hw, IXGBE_FCRTH(packetbuf_num),
- (hw->fc.high_water)|IXGBE_FCRTH_FCEN);
+ (hw->fc.high_water | IXGBE_FCRTH_FCEN));
}
- IXGBE_WRITE_REG(hw, IXGBE_FCTTV(0), hw->fc.pause_time);
+ /* Configure pause time (2 TCs per register) */
+ reg = IXGBE_READ_REG(hw, IXGBE_FCTTV(packetbuf_num));
+ if ((packetbuf_num & 1) == 0)
+ reg = (reg & 0xFFFF0000) | hw->fc.pause_time;
+ else
+ reg = (reg & 0x0000FFFF) | (hw->fc.pause_time << 16);
+ IXGBE_WRITE_REG(hw, IXGBE_FCTTV(packetbuf_num / 2), reg);
+
IXGBE_WRITE_REG(hw, IXGBE_FCRTV, (hw->fc.pause_time >> 1));
- return 0;
+out:
+ return ret_val;
+}
+
+/**
+ * ixgbe_setup_fc_82598 - Configure flow control settings
+ * @hw: pointer to hardware structure
+ * @packetbuf_num: packet buffer number (0-7)
+ *
+ * Configures the flow control settings based on SW configuration. This
+ * function is used for 802.3x flow control configuration only.
+ **/
+static s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
+{
+ s32 ret_val = 0;
+ ixgbe_link_speed speed;
+ bool link_up;
+
+ /* Validate the packetbuf configuration */
+ if (packetbuf_num < 0 || packetbuf_num > 7) {
+ hw_dbg(hw, "Invalid packet buffer number [%d], expected range is"
+ " 0-7\n", packetbuf_num);
+ ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ goto out;
+ }
+
+ /*
+ * Validate the water mark configuration. Zero water marks are invalid
+ * because it causes the controller to just blast out fc packets.
+ */
+ if (!hw->fc.low_water || !hw->fc.high_water || !hw->fc.pause_time) {
+ hw_dbg(hw, "Invalid water mark configuration\n");
+ ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ goto out;
+ }
+
+ /*
+ * Validate the requested mode. Strict IEEE mode does not allow
+ * ixgbe_fc_rx_pause because it will cause testing anomalies.
+ */
+ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
+ hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
+ ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ goto out;
+ }
+
+ /*
+ * 10gig parts do not have a word in the EEPROM to determine the
+ * default flow control setting, so we explicitly set it to full.
+ */
+ if (hw->fc.requested_mode == ixgbe_fc_default)
+ hw->fc.requested_mode = ixgbe_fc_full;
+
+ /*
+ * Save off the requested flow control mode for use later. Depending
+ * on the link partner's capabilities, we may or may not use this mode.
+ */
+
+ hw->fc.current_mode = hw->fc.requested_mode;
+
+ /* Decide whether to use autoneg or not. */
+ hw->mac.ops.check_link(hw, &speed, &link_up, false);
+ if (hw->phy.multispeed_fiber && (speed == IXGBE_LINK_SPEED_1GB_FULL))
+ ret_val = ixgbe_fc_autoneg(hw);
+
+ if (ret_val)
+ goto out;
+
+ ret_val = ixgbe_fc_enable_82598(hw, packetbuf_num);
+
+out:
+ return ret_val;
}
/**
@@ -414,7 +464,6 @@ static s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw)
* case we get disconnected and then reconnected into a different hub
* or switch with different Flow Control capabilities.
*/
- hw->fc.original_type = hw->fc.type;
ixgbe_setup_fc_82598(hw, 0);
/* Add delay to filter out noises during initial link setup */
@@ -1487,6 +1487,144 @@ s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw)
}
/**
+ * ixgbe_fc_autoneg - Configure flow control
+ * @hw: pointer to hardware structure
+ *
+ * Negotiates flow control capabilities with link partner using autoneg and
+ * applies the results.
+ **/
+s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw)
+{
+ s32 ret_val = 0;
+ u32 i, reg, pcs_anadv_reg, pcs_lpab_reg;
+
+ reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
+
+ /*
+ * The possible values of fc.current_mode are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but
+ * we do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ * other: Invalid.
+ */
+ switch (hw->fc.current_mode) {
+ case ixgbe_fc_none:
+ /* Flow control completely disabled by software override. */
+ reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+ break;
+ case ixgbe_fc_rx_pause:
+ /*
+ * Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+ break;
+ case ixgbe_fc_tx_pause:
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is
+ * disabled by software override.
+ */
+ reg |= (IXGBE_PCS1GANA_ASM_PAUSE);
+ reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE);
+ break;
+ case ixgbe_fc_full:
+ /* Flow control (both Rx and Tx) is enabled by SW override. */
+ reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+ break;
+ default:
+ hw_dbg(hw, "Flow control param set incorrectly\n");
+ ret_val = -IXGBE_ERR_CONFIG;
+ goto out;
+ break;
+ }
+
+ IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
+ reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);
+
+ /* Set PCS register for autoneg */
+ /* Enable and restart autoneg */
+ reg |= IXGBE_PCS1GLCTL_AN_ENABLE | IXGBE_PCS1GLCTL_AN_RESTART;
+
+ /* Disable AN timeout */
+ if (hw->fc.strict_ieee)
+ reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;
+
+ hw_dbg(hw, "Configuring Autoneg; PCS_LCTL = 0x%08X\n", reg);
+ IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
+
+ /* See if autonegotiation has succeeded */
+ hw->mac.autoneg_succeeded = 0;
+ for (i = 0; i < FIBER_LINK_UP_LIMIT; i++) {
+ msleep(10);
+ reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA);
+ if ((reg & (IXGBE_PCS1GLSTA_LINK_OK |
+ IXGBE_PCS1GLSTA_AN_COMPLETE)) ==
+ (IXGBE_PCS1GLSTA_LINK_OK |
+ IXGBE_PCS1GLSTA_AN_COMPLETE)) {
+ if (!(reg & IXGBE_PCS1GLSTA_AN_TIMED_OUT))
+ hw->mac.autoneg_succeeded = 1;
+ break;
+ }
+ }
+
+ if (!hw->mac.autoneg_succeeded) {
+ /* Autoneg failed to achieve a link, so we turn fc off */
+ hw->fc.current_mode = ixgbe_fc_none;
+ hw_dbg(hw, "Flow Control = NONE.\n");
+ goto out;
+ }
+
+ /*
+ * Read the AN advertisement and LP ability registers and resolve
+ * local flow control settings accordingly
+ */
+ pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
+ pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP);
+ if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE)) {
+ /*
+ * Now we need to check if the user selected Rx ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == ixgbe_fc_full) {
+ hw->fc.current_mode = ixgbe_fc_full;
+ hw_dbg(hw, "Flow Control = FULL.\n");
+ } else {
+ hw->fc.current_mode = ixgbe_fc_rx_pause;
+ hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
+ }
+ } else if (!(pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) &&
+ (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) {
+ hw->fc.current_mode = ixgbe_fc_tx_pause;
+ hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
+ } else if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) &&
+ !(pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) {
+ hw->fc.current_mode = ixgbe_fc_rx_pause;
+ hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
+ } else {
+ hw->fc.current_mode = ixgbe_fc_none;
+ hw_dbg(hw, "Flow Control = NONE.\n");
+ }
+
+out:
+ return ret_val;
+}
+
+/**
* ixgbe_disable_pcie_master - Disable PCI-express master access
* @hw: pointer to hardware structure
*
@@ -61,6 +61,9 @@ s32 ixgbe_update_uc_addr_list_generic(struct ixgbe_hw *hw, u8 *addr_list,
u32 addr_count, ixgbe_mc_addr_itr func);
s32 ixgbe_enable_mc_generic(struct ixgbe_hw *hw);
s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw);
+s32 ixgbe_setup_fc_generic(struct ixgbe_hw *hw, s32 packetbuf_num);
+s32 ixgbe_fc_enable(struct ixgbe_hw *hw, s32 packtetbuf_num);
+s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw);
s32 ixgbe_validate_mac_addr(u8 *mac_addr);
s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u16 mask);
@@ -298,7 +298,7 @@ s32 ixgbe_dcb_config_pfc_82598(struct ixgbe_hw *hw,
reg = IXGBE_READ_REG(hw, IXGBE_RMCS);
reg &= ~IXGBE_RMCS_TFCE_802_3X;
/* correct the reporting of our flow control status */
- hw->fc.type = ixgbe_fc_none;
+ hw->fc.current_mode = ixgbe_fc_none;
reg |= IXGBE_RMCS_TFCE_PRIORITY;
IXGBE_WRITE_REG(hw, IXGBE_RMCS, reg);
@@ -224,13 +224,13 @@ static void ixgbe_get_pauseparam(struct net_device *netdev,
struct ixgbe_adapter *adapter = netdev_priv(netdev);
struct ixgbe_hw *hw = &adapter->hw;
- pause->autoneg = (hw->fc.type == ixgbe_fc_full ? 1 : 0);
+ pause->autoneg = (hw->fc.current_mode == ixgbe_fc_full ? 1 : 0);
- if (hw->fc.type == ixgbe_fc_rx_pause) {
+ if (hw->fc.current_mode == ixgbe_fc_rx_pause) {
pause->rx_pause = 1;
- } else if (hw->fc.type == ixgbe_fc_tx_pause) {
+ } else if (hw->fc.current_mode == ixgbe_fc_tx_pause) {
pause->tx_pause = 1;
- } else if (hw->fc.type == ixgbe_fc_full) {
+ } else if (hw->fc.current_mode == ixgbe_fc_full) {
pause->rx_pause = 1;
pause->tx_pause = 1;
}
@@ -244,22 +244,17 @@ static int ixgbe_set_pauseparam(struct net_device *netdev,
if ((pause->autoneg == AUTONEG_ENABLE) ||
(pause->rx_pause && pause->tx_pause))
- hw->fc.type = ixgbe_fc_full;
+ hw->fc.requested_mode = ixgbe_fc_full;
else if (pause->rx_pause && !pause->tx_pause)
- hw->fc.type = ixgbe_fc_rx_pause;
+ hw->fc.requested_mode = ixgbe_fc_rx_pause;
else if (!pause->rx_pause && pause->tx_pause)
- hw->fc.type = ixgbe_fc_tx_pause;
+ hw->fc.requested_mode = ixgbe_fc_tx_pause;
else if (!pause->rx_pause && !pause->tx_pause)
- hw->fc.type = ixgbe_fc_none;
+ hw->fc.requested_mode = ixgbe_fc_none;
else
return -EINVAL;
- hw->fc.original_type = hw->fc.type;
-
- if (netif_running(netdev))
- ixgbe_reinit_locked(adapter);
- else
- ixgbe_reset(adapter);
+ hw->mac.ops.setup_fc(hw, 0);
return 0;
}
@@ -1954,11 +1954,43 @@ static void ixgbe_configure(struct ixgbe_adapter *adapter)
(adapter->rx_ring[i].count - 1));
}
+/**
+ * ixgbe_link_config - set up initial link with default speed and duplex
+ * @hw: pointer to private hardware struct
+ *
+ * Returns 0 on success, negative on failure
+ **/
+static int ixgbe_link_config(struct ixgbe_hw *hw)
+{
+ u32 autoneg;
+ bool link_up = false;
+ u32 ret = IXGBE_ERR_LINK_SETUP;
+
+ if (hw->mac.ops.check_link)
+ ret = hw->mac.ops.check_link(hw, &autoneg, &link_up, false);
+
+ if (ret)
+ goto link_cfg_out;
+
+ if (hw->mac.ops.get_link_capabilities)
+ ret = hw->mac.ops.get_link_capabilities(hw, &autoneg,
+ &hw->mac.autoneg);
+ if (ret)
+ goto link_cfg_out;
+
+ if (hw->mac.ops.setup_link_speed)
+ ret = hw->mac.ops.setup_link_speed(hw, autoneg, true, link_up);
+
+link_cfg_out:
+ return ret;
+}
+
static int ixgbe_up_complete(struct ixgbe_adapter *adapter)
{
struct net_device *netdev = adapter->netdev;
struct ixgbe_hw *hw = &adapter->hw;
int i, j = 0;
+ int err;
int max_frame = netdev->mtu + ETH_HLEN + ETH_FCS_LEN;
u32 txdctl, rxdctl, mhadd;
u32 gpie;
@@ -2039,6 +2071,10 @@ static int ixgbe_up_complete(struct ixgbe_adapter *adapter)
ixgbe_irq_enable(adapter);
+ err = ixgbe_link_config(hw);
+ if (err)
+ dev_err(&adapter->pdev->dev, "link_config FAILED %d\n", err);
+
/* enable transmits */
netif_tx_start_all_queues(netdev);
@@ -2792,8 +2828,7 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter)
adapter->flags |= IXGBE_FLAG_FAN_FAIL_CAPABLE;
/* default flow control settings */
- hw->fc.original_type = ixgbe_fc_none;
- hw->fc.type = ixgbe_fc_none;
+ hw->fc.requested_mode = ixgbe_fc_none;
hw->fc.high_water = IXGBE_DEFAULT_FCRTH;
hw->fc.low_water = IXGBE_DEFAULT_FCRTL;
hw->fc.pause_time = IXGBE_DEFAULT_FCPAUSE;
@@ -3916,37 +3951,6 @@ static void ixgbe_netpoll(struct net_device *netdev)
}
#endif
-/**
- * ixgbe_link_config - set up initial link with default speed and duplex
- * @hw: pointer to private hardware struct
- *
- * Returns 0 on success, negative on failure
- **/
-static int ixgbe_link_config(struct ixgbe_hw *hw)
-{
- u32 autoneg;
- bool link_up = false;
- u32 ret = IXGBE_ERR_LINK_SETUP;
-
- if (hw->mac.ops.check_link)
- ret = hw->mac.ops.check_link(hw, &autoneg, &link_up, false);
-
- if (ret || !link_up)
- goto link_cfg_out;
-
- if (hw->mac.ops.get_link_capabilities)
- ret = hw->mac.ops.get_link_capabilities(hw, &autoneg,
- &hw->mac.autoneg);
- if (ret)
- goto link_cfg_out;
-
- if (hw->mac.ops.setup_link_speed)
- ret = hw->mac.ops.setup_link_speed(hw, autoneg, true, true);
-
-link_cfg_out:
- return ret;
-}
-
static const struct net_device_ops ixgbe_netdev_ops = {
.ndo_open = ixgbe_open,
.ndo_stop = ixgbe_close,
@@ -4197,13 +4201,6 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
/* reset the hardware with the new settings */
hw->mac.ops.start_hw(hw);
- /* link_config depends on start_hw being called at least once */
- err = ixgbe_link_config(hw);
- if (err) {
- dev_err(&pdev->dev, "setup_link_speed FAILED %d\n", err);
- goto err_register;
- }
-
netif_carrier_off(netdev);
strcpy(netdev->name, "eth%d");
@@ -771,6 +771,28 @@
#define IXGBE_LINK_UP_TIME 90 /* 9.0 Seconds */
#define IXGBE_AUTO_NEG_TIME 45 /* 4.5 Seconds */
+#define FIBER_LINK_UP_LIMIT 50
+
+/* PCS1GLSTA Bit Masks */
+#define IXGBE_PCS1GLSTA_LINK_OK 1
+#define IXGBE_PCS1GLSTA_SYNK_OK 0x10
+#define IXGBE_PCS1GLSTA_AN_COMPLETE 0x10000
+#define IXGBE_PCS1GLSTA_AN_PAGE_RX 0x20000
+#define IXGBE_PCS1GLSTA_AN_TIMED_OUT 0x40000
+#define IXGBE_PCS1GLSTA_AN_REMOTE_FAULT 0x80000
+#define IXGBE_PCS1GLSTA_AN_ERROR_RWS 0x100000
+
+#define IXGBE_PCS1GANA_SYM_PAUSE 0x80
+#define IXGBE_PCS1GANA_ASM_PAUSE 0x100
+
+/* PCS1GLCTL Bit Masks */
+#define IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN 0x00040000 /* PCS 1G autoneg to en */
+#define IXGBE_PCS1GLCTL_FLV_LINK_UP 1
+#define IXGBE_PCS1GLCTL_FORCE_LINK 0x20
+#define IXGBE_PCS1GLCTL_LOW_LINK_LATCH 0x40
+#define IXGBE_PCS1GLCTL_AN_ENABLE 0x10000
+#define IXGBE_PCS1GLCTL_AN_RESTART 0x20000
+
/* SW Semaphore Register bitmasks */
#define IXGBE_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
#define IXGBE_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
@@ -1270,7 +1292,7 @@ enum ixgbe_media_type {
};
/* Flow Control Settings */
-enum ixgbe_fc_type {
+enum ixgbe_fc_mode {
ixgbe_fc_none = 0,
ixgbe_fc_rx_pause,
ixgbe_fc_tx_pause,
@@ -1294,8 +1316,8 @@ struct ixgbe_fc_info {
u16 pause_time; /* Flow Control Pause timer */
bool send_xon; /* Flow control send XON */
bool strict_ieee; /* Strict IEEE mode */
- enum ixgbe_fc_type type; /* Type of flow control */
- enum ixgbe_fc_type original_type;
+ enum ixgbe_fc_mode current_mode; /* FC mode in effect */
+ enum ixgbe_fc_mode requested_mode; /* FC mode requested by caller */
};
/* Statistics counters collected by the MAC */
@@ -1475,6 +1497,7 @@ struct ixgbe_phy_info {
bool reset_disable;
ixgbe_autoneg_advertised autoneg_advertised;
bool autoneg_wait_to_complete;
+ bool multispeed_fiber;
};
struct ixgbe_hw {