diff mbox

[4/9] sky2: set VPD size

Message ID 20080925165223.451775520@vyatta.com
State Deferred, archived
Delegated to: Jeff Garzik
Headers show

Commit Message

stephen hemminger Sept. 25, 2008, 4:48 p.m. UTC 
Read configuration register during probe and use it to size the
available VPD. Move existing code using same register slightly
earlier in probe handling.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
diff mbox

Patch

--- a/drivers/net/sky2.c	2008-09-09 13:56:09.000000000 -0700
+++ b/drivers/net/sky2.c	2008-09-09 13:57:07.000000000 -0700
@@ -4281,6 +4281,7 @@  static int __devinit sky2_probe(struct p
 	struct net_device *dev;
 	struct sky2_hw *hw;
 	int err, using_dac = 0, wol_default;
+	u32 reg;
 	char buf1[16];
 
 	err = pci_enable_device(pdev);
@@ -4314,6 +4315,34 @@  static int __devinit sky2_probe(struct p
 		}
 	}
 
+	/* Get configuration information
+	 * Note: only regular PCI config access once to test for HW issues
+	 *       other PCI access through shared memory for speed and to
+	 *	 avoid MMCONFIG problems.
+	 */
+	err = pci_read_config_dword(pdev, PCI_DEV_REG2, &reg);
+	if (err) {
+		dev_err(&pdev->dev, "PCI read config failed\n");
+		goto err_out_free_regions;
+	}
+
+	/* size of available VPD, only impact sysfs */
+	err = pci_vpd_truncate(pdev, 1ul << (((reg & PCI_VPD_ROM_SZ) >> 14) + 8));
+	if (err)
+		dev_warn(&pdev->dev, "Can't set VPD size\n");
+
+#ifdef __BIG_ENDIAN
+	/* The sk98lin vendor driver uses hardware byte swapping but
+	 * this driver uses software swapping.
+	 */
+	reg &= ~PCI_REV_DESC;
+	err = pci_write_config_dword(pdev,PCI_DEV_REG2, reg);
+	if (err) {
+		dev_err(&pdev->dev, "PCI write config failed\n");
+		goto err_out_free_regions;
+	}
+#endif
+
 	wol_default = pci_wake_enabled(pdev) ? WAKE_MAGIC : 0;
 
 	err = -ENOMEM;
@@ -4331,18 +4360,6 @@  static int __devinit sky2_probe(struct p
 		goto err_out_free_hw;
 	}
 
-#ifdef __BIG_ENDIAN
-	/* The sk98lin vendor driver uses hardware byte swapping but
-	 * this driver uses software swapping.
-	 */
-	{
-		u32 reg;
-		reg = sky2_pci_read32(hw, PCI_DEV_REG2);
-		reg &= ~PCI_REV_DESC;
-		sky2_pci_write32(hw, PCI_DEV_REG2, reg);
-	}
-#endif
-
 	/* ring for status responses */
 	hw->st_le = pci_alloc_consistent(pdev, STATUS_LE_BYTES, &hw->st_dma);
 	if (!hw->st_le)