diff mbox series

[v2,net-next,4/4] net: nfc: s3fwrn5: Support a UART interface

Message ID 1606737945-29634-1-git-send-email-bongsu.jeon@samsung.com
State New
Headers show
Series [v2,net-next,1/4] dt-bindings: net: nfc: s3fwrn5: Support a UART interface | expand

Commit Message

Bongsu Jeon Nov. 30, 2020, 12:05 p.m. UTC
From: Bongsu Jeon <bongsu.jeon@samsung.com>

Since S3FWRN82 NFC Chip, The UART interface can be used.
S3FWRN82 uses NCI protocol and supports I2C and UART interface.

Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
---

 Changes in v2:
   - remove the kfree(phy) because of duplicated free.
   - use the phy_common blocks.
   - wrap lines properly.

 drivers/nfc/s3fwrn5/Kconfig      |  12 +++
 drivers/nfc/s3fwrn5/Makefile     |   2 +
 drivers/nfc/s3fwrn5/phy_common.c |  12 +++
 drivers/nfc/s3fwrn5/phy_common.h |   1 +
 drivers/nfc/s3fwrn5/uart.c       | 197 +++++++++++++++++++++++++++++++++++++++
 5 files changed, 224 insertions(+)
 create mode 100644 drivers/nfc/s3fwrn5/uart.c

Comments

Krzysztof Kozlowski Nov. 30, 2020, 6:45 p.m. UTC | #1
On Mon, Nov 30, 2020 at 09:05:45PM +0900, Bongsu Jeon wrote:
> From: Bongsu Jeon <bongsu.jeon@samsung.com>
> 
> Since S3FWRN82 NFC Chip, The UART interface can be used.
> S3FWRN82 uses NCI protocol and supports I2C and UART interface.
> 
> Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
> ---
> 
>  Changes in v2:
>    - remove the kfree(phy) because of duplicated free.
>    - use the phy_common blocks.
>    - wrap lines properly.
> 
>  drivers/nfc/s3fwrn5/Kconfig      |  12 +++
>  drivers/nfc/s3fwrn5/Makefile     |   2 +
>  drivers/nfc/s3fwrn5/phy_common.c |  12 +++
>  drivers/nfc/s3fwrn5/phy_common.h |   1 +
>  drivers/nfc/s3fwrn5/uart.c       | 197 +++++++++++++++++++++++++++++++++++++++
>  5 files changed, 224 insertions(+)
>  create mode 100644 drivers/nfc/s3fwrn5/uart.c
> 
> diff --git a/drivers/nfc/s3fwrn5/Kconfig b/drivers/nfc/s3fwrn5/Kconfig
> index 3f8b6da..8a6b1a7 100644
> --- a/drivers/nfc/s3fwrn5/Kconfig
> +++ b/drivers/nfc/s3fwrn5/Kconfig
> @@ -20,3 +20,15 @@ config NFC_S3FWRN5_I2C
>  	  To compile this driver as a module, choose m here. The module will
>  	  be called s3fwrn5_i2c.ko.
>  	  Say N if unsure.
> +
> +config NFC_S3FWRN82_UART
> +        tristate "Samsung S3FWRN82 UART support"
> +        depends on NFC_NCI && SERIAL_DEV_BUS
> +        select NFC_S3FWRN5
> +        help
> +          This module adds support for a UART interface to the S3FWRN82 chip.
> +          Select this if your platform is using the UART bus.
> +
> +          To compile this driver as a module, choose m here. The module will
> +          be called s3fwrn82_uart.ko.
> +          Say N if unsure.
> diff --git a/drivers/nfc/s3fwrn5/Makefile b/drivers/nfc/s3fwrn5/Makefile
> index 6b6f52d..7da827a 100644
> --- a/drivers/nfc/s3fwrn5/Makefile
> +++ b/drivers/nfc/s3fwrn5/Makefile
> @@ -5,6 +5,8 @@
>  
>  s3fwrn5-objs = core.o firmware.o nci.o phy_common.o
>  s3fwrn5_i2c-objs = i2c.o
> +s3fwrn82_uart-objs = uart.o
>  
>  obj-$(CONFIG_NFC_S3FWRN5) += s3fwrn5.o
>  obj-$(CONFIG_NFC_S3FWRN5_I2C) += s3fwrn5_i2c.o
> +obj-$(CONFIG_NFC_S3FWRN82_UART) += s3fwrn82_uart.o
> diff --git a/drivers/nfc/s3fwrn5/phy_common.c b/drivers/nfc/s3fwrn5/phy_common.c
> index 5cad1f4..497b02b 100644
> --- a/drivers/nfc/s3fwrn5/phy_common.c
> +++ b/drivers/nfc/s3fwrn5/phy_common.c
> @@ -47,6 +47,18 @@ bool s3fwrn5_phy_power_ctrl(struct phy_common *phy, enum s3fwrn5_mode mode)
>  }
>  EXPORT_SYMBOL(s3fwrn5_phy_power_ctrl);
>  
> +void s3fwrn5_phy_set_mode(void *phy_id, enum s3fwrn5_mode mode)
> +{
> +	struct phy_common *phy = phy_id;
> +
> +	mutex_lock(&phy->mutex);
> +
> +	s3fwrn5_phy_power_ctrl(phy, mode);
> +
> +	mutex_unlock(&phy->mutex);
> +}
> +EXPORT_SYMBOL(s3fwrn5_phy_set_mode);
> +
>  enum s3fwrn5_mode s3fwrn5_phy_get_mode(void *phy_id)
>  {
>  	struct phy_common *phy = phy_id;
> diff --git a/drivers/nfc/s3fwrn5/phy_common.h b/drivers/nfc/s3fwrn5/phy_common.h
> index b98531d..99749c9 100644
> --- a/drivers/nfc/s3fwrn5/phy_common.h
> +++ b/drivers/nfc/s3fwrn5/phy_common.h
> @@ -31,6 +31,7 @@ struct phy_common {
>  
>  void s3fwrn5_phy_set_wake(void *phy_id, bool wake);
>  bool s3fwrn5_phy_power_ctrl(struct phy_common *phy, enum s3fwrn5_mode mode);
> +void s3fwrn5_phy_set_mode(void *phy_id, enum s3fwrn5_mode mode);
>  enum s3fwrn5_mode s3fwrn5_phy_get_mode(void *phy_id);
>  
>  #endif /* __NFC_S3FWRN5_PHY_COMMON_H */
> diff --git a/drivers/nfc/s3fwrn5/uart.c b/drivers/nfc/s3fwrn5/uart.c
> new file mode 100644
> index 0000000..f5ac017
> --- /dev/null
> +++ b/drivers/nfc/s3fwrn5/uart.c
> @@ -0,0 +1,197 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * UART Link Layer for S3FWRN82 NCI based Driver
> + *
> + * Copyright (C) 2015 Samsung Electronics
> + * Robert Baldyga <r.baldyga@samsung.com>
> + * Copyright (C) 2020 Samsung Electronics
> + * Bongsu Jeon <bongsu.jeon@samsung.com>
> + */
> +
> +#include <linux/device.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/nfc.h>
> +#include <linux/netdevice.h>
> +#include <linux/of.h>
> +#include <linux/serdev.h>
> +#include <linux/gpio.h>
> +#include <linux/of_gpio.h>
> +
> +#include "phy_common.h"
> +
> +#define S3FWRN82_NCI_HEADER 3
> +#define S3FWRN82_NCI_IDX 2
> +#define NCI_SKB_BUFF_LEN 258
> +
> +struct s3fwrn82_uart_phy {
> +	struct phy_common common;
> +	struct serdev_device *ser_dev;
> +	struct sk_buff *recv_skb;
> +};
> +
> +static int s3fwrn82_uart_write(void *phy_id, struct sk_buff *out)
> +{
> +	struct s3fwrn82_uart_phy *phy = phy_id;
> +	int err;
> +
> +	err = serdev_device_write(phy->ser_dev,
> +				  out->data, out->len,
> +				  MAX_SCHEDULE_TIMEOUT);
> +	if (err < 0)
> +		return err;
> +
> +	return 0;
> +}
> +
> +static const struct s3fwrn5_phy_ops uart_phy_ops = {
> +	.set_wake = s3fwrn5_phy_set_wake,
> +	.set_mode = s3fwrn5_phy_set_mode,
> +	.get_mode = s3fwrn5_phy_get_mode,
> +	.write = s3fwrn82_uart_write,
> +};
> +
> +static int s3fwrn82_uart_read(struct serdev_device *serdev,
> +			      const unsigned char *data,
> +			      size_t count)
> +{
> +	struct s3fwrn82_uart_phy *phy = serdev_device_get_drvdata(serdev);
> +	size_t i;
> +
> +	for (i = 0; i < count; i++) {
> +		skb_put_u8(phy->recv_skb, *data++);
> +
> +		if (phy->recv_skb->len < S3FWRN82_NCI_HEADER)
> +			continue;
> +
> +		if ((phy->recv_skb->len - S3FWRN82_NCI_HEADER)
> +				< phy->recv_skb->data[S3FWRN82_NCI_IDX])
> +			continue;
> +
> +		s3fwrn5_recv_frame(phy->common.ndev, phy->recv_skb,
> +				   phy->common.mode);
> +		phy->recv_skb = alloc_skb(NCI_SKB_BUFF_LEN, GFP_KERNEL);
> +		if (!phy->recv_skb)
> +			return 0;
> +	}
> +
> +	return i;
> +}
> +
> +static const struct serdev_device_ops s3fwrn82_serdev_ops = {
> +	.receive_buf = s3fwrn82_uart_read,
> +	.write_wakeup = serdev_device_write_wakeup,
> +};
> +
> +static const struct of_device_id s3fwrn82_uart_of_match[] = {
> +	{ .compatible = "samsung,s3fwrn82", },
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, s3fwrn82_uart_of_match);
> +
> +static int s3fwrn82_uart_parse_dt(struct serdev_device *serdev)
> +{
> +	struct s3fwrn82_uart_phy *phy = serdev_device_get_drvdata(serdev);
> +	struct device_node *np = serdev->dev.of_node;
> +
> +	if (!np)
> +		return -ENODEV;
> +
> +	phy->common.gpio_en = of_get_named_gpio(np, "en-gpios", 0);
> +	if (!gpio_is_valid(phy->common.gpio_en))
> +		return -ENODEV;
> +
> +	phy->common.gpio_fw_wake = of_get_named_gpio(np, "wake-gpios", 0);
> +	if (!gpio_is_valid(phy->common.gpio_fw_wake))
> +		return -ENODEV;
> +
> +	return 0;
> +}
> +
> +static int s3fwrn82_uart_probe(struct serdev_device *serdev)
> +{
> +	struct s3fwrn82_uart_phy *phy;
> +	int ret = -ENOMEM;
> +
> +	phy = devm_kzalloc(&serdev->dev, sizeof(*phy), GFP_KERNEL);
> +	if (!phy)
> +		goto err_exit;
> +
> +	phy->recv_skb = alloc_skb(NCI_SKB_BUFF_LEN, GFP_KERNEL);
> +	if (!phy->recv_skb)
> +		goto err_free;
> +
> +	mutex_init(&phy->common.mutex);
> +	phy->common.mode = S3FWRN5_MODE_COLD;
> +
> +	phy->ser_dev = serdev;
> +	serdev_device_set_drvdata(serdev, phy);
> +	serdev_device_set_client_ops(serdev, &s3fwrn82_serdev_ops);
> +	ret = serdev_device_open(serdev);
> +	if (ret) {
> +		dev_err(&serdev->dev, "Unable to open device\n");
> +		goto err_skb;
> +	}
> +
> +	ret = serdev_device_set_baudrate(serdev, 115200);
> +	if (ret != 115200) {
> +		ret = -EINVAL;
> +		goto err_serdev;
> +	}
> +
> +	serdev_device_set_flow_control(serdev, false);
> +
> +	ret = s3fwrn82_uart_parse_dt(serdev);
> +	if (ret < 0)
> +		goto err_serdev;
> +
> +	ret = devm_gpio_request_one(&phy->ser_dev->dev, phy->common.gpio_en,
> +				    GPIOF_OUT_INIT_HIGH, "s3fwrn82_en");
> +	if (ret < 0)
> +		goto err_serdev;
> +
> +	ret = devm_gpio_request_one(&phy->ser_dev->dev,
> +				    phy->common.gpio_fw_wake,
> +				    GPIOF_OUT_INIT_LOW, "s3fwrn82_fw_wake");
> +	if (ret < 0)
> +		goto err_serdev;
> +
> +	ret = s3fwrn5_probe(&phy->common.ndev, phy, &phy->ser_dev->dev,
> +			    &uart_phy_ops);
> +	if (ret < 0)
> +		goto err_serdev;
> +
> +	return ret;
> +
> +err_serdev:
> +	serdev_device_close(serdev);
> +err_skb:
> +	kfree_skb(phy->recv_skb);
> +err_free:
> +err_exit:
> +	return ret;
> +}
> +
> +static void s3fwrn82_uart_remove(struct serdev_device *serdev)
> +{
> +	struct s3fwrn82_uart_phy *phy = serdev_device_get_drvdata(serdev);
> +
> +	s3fwrn5_remove(phy->common.ndev);
> +	serdev_device_close(serdev);
> +	kfree_skb(phy->recv_skb);
> +}
> +
> +static struct serdev_device_driver s3fwrn82_uart_driver = {
> +	.probe = s3fwrn82_uart_probe,
> +	.remove = s3fwrn82_uart_remove,
> +	.driver = {
> +		.name = "s3fwrn82_uart",
> +		.of_match_table = of_match_ptr(s3fwrn82_uart_of_match),

Compile with W=1. Fix the warnings - preferably by removing
of_match_ptr().

Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/drivers/nfc/s3fwrn5/Kconfig b/drivers/nfc/s3fwrn5/Kconfig
index 3f8b6da..8a6b1a7 100644
--- a/drivers/nfc/s3fwrn5/Kconfig
+++ b/drivers/nfc/s3fwrn5/Kconfig
@@ -20,3 +20,15 @@  config NFC_S3FWRN5_I2C
 	  To compile this driver as a module, choose m here. The module will
 	  be called s3fwrn5_i2c.ko.
 	  Say N if unsure.
+
+config NFC_S3FWRN82_UART
+        tristate "Samsung S3FWRN82 UART support"
+        depends on NFC_NCI && SERIAL_DEV_BUS
+        select NFC_S3FWRN5
+        help
+          This module adds support for a UART interface to the S3FWRN82 chip.
+          Select this if your platform is using the UART bus.
+
+          To compile this driver as a module, choose m here. The module will
+          be called s3fwrn82_uart.ko.
+          Say N if unsure.
diff --git a/drivers/nfc/s3fwrn5/Makefile b/drivers/nfc/s3fwrn5/Makefile
index 6b6f52d..7da827a 100644
--- a/drivers/nfc/s3fwrn5/Makefile
+++ b/drivers/nfc/s3fwrn5/Makefile
@@ -5,6 +5,8 @@ 
 
 s3fwrn5-objs = core.o firmware.o nci.o phy_common.o
 s3fwrn5_i2c-objs = i2c.o
+s3fwrn82_uart-objs = uart.o
 
 obj-$(CONFIG_NFC_S3FWRN5) += s3fwrn5.o
 obj-$(CONFIG_NFC_S3FWRN5_I2C) += s3fwrn5_i2c.o
+obj-$(CONFIG_NFC_S3FWRN82_UART) += s3fwrn82_uart.o
diff --git a/drivers/nfc/s3fwrn5/phy_common.c b/drivers/nfc/s3fwrn5/phy_common.c
index 5cad1f4..497b02b 100644
--- a/drivers/nfc/s3fwrn5/phy_common.c
+++ b/drivers/nfc/s3fwrn5/phy_common.c
@@ -47,6 +47,18 @@  bool s3fwrn5_phy_power_ctrl(struct phy_common *phy, enum s3fwrn5_mode mode)
 }
 EXPORT_SYMBOL(s3fwrn5_phy_power_ctrl);
 
+void s3fwrn5_phy_set_mode(void *phy_id, enum s3fwrn5_mode mode)
+{
+	struct phy_common *phy = phy_id;
+
+	mutex_lock(&phy->mutex);
+
+	s3fwrn5_phy_power_ctrl(phy, mode);
+
+	mutex_unlock(&phy->mutex);
+}
+EXPORT_SYMBOL(s3fwrn5_phy_set_mode);
+
 enum s3fwrn5_mode s3fwrn5_phy_get_mode(void *phy_id)
 {
 	struct phy_common *phy = phy_id;
diff --git a/drivers/nfc/s3fwrn5/phy_common.h b/drivers/nfc/s3fwrn5/phy_common.h
index b98531d..99749c9 100644
--- a/drivers/nfc/s3fwrn5/phy_common.h
+++ b/drivers/nfc/s3fwrn5/phy_common.h
@@ -31,6 +31,7 @@  struct phy_common {
 
 void s3fwrn5_phy_set_wake(void *phy_id, bool wake);
 bool s3fwrn5_phy_power_ctrl(struct phy_common *phy, enum s3fwrn5_mode mode);
+void s3fwrn5_phy_set_mode(void *phy_id, enum s3fwrn5_mode mode);
 enum s3fwrn5_mode s3fwrn5_phy_get_mode(void *phy_id);
 
 #endif /* __NFC_S3FWRN5_PHY_COMMON_H */
diff --git a/drivers/nfc/s3fwrn5/uart.c b/drivers/nfc/s3fwrn5/uart.c
new file mode 100644
index 0000000..f5ac017
--- /dev/null
+++ b/drivers/nfc/s3fwrn5/uart.c
@@ -0,0 +1,197 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * UART Link Layer for S3FWRN82 NCI based Driver
+ *
+ * Copyright (C) 2015 Samsung Electronics
+ * Robert Baldyga <r.baldyga@samsung.com>
+ * Copyright (C) 2020 Samsung Electronics
+ * Bongsu Jeon <bongsu.jeon@samsung.com>
+ */
+
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nfc.h>
+#include <linux/netdevice.h>
+#include <linux/of.h>
+#include <linux/serdev.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
+
+#include "phy_common.h"
+
+#define S3FWRN82_NCI_HEADER 3
+#define S3FWRN82_NCI_IDX 2
+#define NCI_SKB_BUFF_LEN 258
+
+struct s3fwrn82_uart_phy {
+	struct phy_common common;
+	struct serdev_device *ser_dev;
+	struct sk_buff *recv_skb;
+};
+
+static int s3fwrn82_uart_write(void *phy_id, struct sk_buff *out)
+{
+	struct s3fwrn82_uart_phy *phy = phy_id;
+	int err;
+
+	err = serdev_device_write(phy->ser_dev,
+				  out->data, out->len,
+				  MAX_SCHEDULE_TIMEOUT);
+	if (err < 0)
+		return err;
+
+	return 0;
+}
+
+static const struct s3fwrn5_phy_ops uart_phy_ops = {
+	.set_wake = s3fwrn5_phy_set_wake,
+	.set_mode = s3fwrn5_phy_set_mode,
+	.get_mode = s3fwrn5_phy_get_mode,
+	.write = s3fwrn82_uart_write,
+};
+
+static int s3fwrn82_uart_read(struct serdev_device *serdev,
+			      const unsigned char *data,
+			      size_t count)
+{
+	struct s3fwrn82_uart_phy *phy = serdev_device_get_drvdata(serdev);
+	size_t i;
+
+	for (i = 0; i < count; i++) {
+		skb_put_u8(phy->recv_skb, *data++);
+
+		if (phy->recv_skb->len < S3FWRN82_NCI_HEADER)
+			continue;
+
+		if ((phy->recv_skb->len - S3FWRN82_NCI_HEADER)
+				< phy->recv_skb->data[S3FWRN82_NCI_IDX])
+			continue;
+
+		s3fwrn5_recv_frame(phy->common.ndev, phy->recv_skb,
+				   phy->common.mode);
+		phy->recv_skb = alloc_skb(NCI_SKB_BUFF_LEN, GFP_KERNEL);
+		if (!phy->recv_skb)
+			return 0;
+	}
+
+	return i;
+}
+
+static const struct serdev_device_ops s3fwrn82_serdev_ops = {
+	.receive_buf = s3fwrn82_uart_read,
+	.write_wakeup = serdev_device_write_wakeup,
+};
+
+static const struct of_device_id s3fwrn82_uart_of_match[] = {
+	{ .compatible = "samsung,s3fwrn82", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, s3fwrn82_uart_of_match);
+
+static int s3fwrn82_uart_parse_dt(struct serdev_device *serdev)
+{
+	struct s3fwrn82_uart_phy *phy = serdev_device_get_drvdata(serdev);
+	struct device_node *np = serdev->dev.of_node;
+
+	if (!np)
+		return -ENODEV;
+
+	phy->common.gpio_en = of_get_named_gpio(np, "en-gpios", 0);
+	if (!gpio_is_valid(phy->common.gpio_en))
+		return -ENODEV;
+
+	phy->common.gpio_fw_wake = of_get_named_gpio(np, "wake-gpios", 0);
+	if (!gpio_is_valid(phy->common.gpio_fw_wake))
+		return -ENODEV;
+
+	return 0;
+}
+
+static int s3fwrn82_uart_probe(struct serdev_device *serdev)
+{
+	struct s3fwrn82_uart_phy *phy;
+	int ret = -ENOMEM;
+
+	phy = devm_kzalloc(&serdev->dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy)
+		goto err_exit;
+
+	phy->recv_skb = alloc_skb(NCI_SKB_BUFF_LEN, GFP_KERNEL);
+	if (!phy->recv_skb)
+		goto err_free;
+
+	mutex_init(&phy->common.mutex);
+	phy->common.mode = S3FWRN5_MODE_COLD;
+
+	phy->ser_dev = serdev;
+	serdev_device_set_drvdata(serdev, phy);
+	serdev_device_set_client_ops(serdev, &s3fwrn82_serdev_ops);
+	ret = serdev_device_open(serdev);
+	if (ret) {
+		dev_err(&serdev->dev, "Unable to open device\n");
+		goto err_skb;
+	}
+
+	ret = serdev_device_set_baudrate(serdev, 115200);
+	if (ret != 115200) {
+		ret = -EINVAL;
+		goto err_serdev;
+	}
+
+	serdev_device_set_flow_control(serdev, false);
+
+	ret = s3fwrn82_uart_parse_dt(serdev);
+	if (ret < 0)
+		goto err_serdev;
+
+	ret = devm_gpio_request_one(&phy->ser_dev->dev, phy->common.gpio_en,
+				    GPIOF_OUT_INIT_HIGH, "s3fwrn82_en");
+	if (ret < 0)
+		goto err_serdev;
+
+	ret = devm_gpio_request_one(&phy->ser_dev->dev,
+				    phy->common.gpio_fw_wake,
+				    GPIOF_OUT_INIT_LOW, "s3fwrn82_fw_wake");
+	if (ret < 0)
+		goto err_serdev;
+
+	ret = s3fwrn5_probe(&phy->common.ndev, phy, &phy->ser_dev->dev,
+			    &uart_phy_ops);
+	if (ret < 0)
+		goto err_serdev;
+
+	return ret;
+
+err_serdev:
+	serdev_device_close(serdev);
+err_skb:
+	kfree_skb(phy->recv_skb);
+err_free:
+err_exit:
+	return ret;
+}
+
+static void s3fwrn82_uart_remove(struct serdev_device *serdev)
+{
+	struct s3fwrn82_uart_phy *phy = serdev_device_get_drvdata(serdev);
+
+	s3fwrn5_remove(phy->common.ndev);
+	serdev_device_close(serdev);
+	kfree_skb(phy->recv_skb);
+}
+
+static struct serdev_device_driver s3fwrn82_uart_driver = {
+	.probe = s3fwrn82_uart_probe,
+	.remove = s3fwrn82_uart_remove,
+	.driver = {
+		.name = "s3fwrn82_uart",
+		.of_match_table = of_match_ptr(s3fwrn82_uart_of_match),
+	},
+};
+
+module_serdev_device_driver(s3fwrn82_uart_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("UART driver for Samsung NFC");
+MODULE_AUTHOR("Bongsu Jeon <bongsu.jeon@samsung.com>");