Message ID | 1456775971-4946-3-git-send-email-marex@denx.de |
---|---|
State | Awaiting Upstream, archived |
Delegated to: | David Miller |
Headers | show |
On 02/29/2016 08:59 PM, Marek Vasut wrote: > The TX DLC, the transmission length information, was not written > into the transmit configuration register. When using the CAN core > with different CAN controller, the receiving CAN controller will > receive only the ID part of the CAN frame, but no data at all. > > This patch adds the TX DLC into the register to fix this issue. > > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Marc Kleine-Budde <mkl@pengutronix.de> > Cc: Mark Rutland <mark.rutland@arm.com> > Cc: Oliver Hartkopp <socketcan@hartkopp.net> > Cc: Wolfgang Grandegger <wg@grandegger.com> > --- > drivers/net/can/ifi_canfd/ifi_canfd.c | 5 +++++ > 1 file changed, 5 insertions(+) > > diff --git a/drivers/net/can/ifi_canfd/ifi_canfd.c b/drivers/net/can/ifi_canfd/ifi_canfd.c > index 72f5205..82a33bd 100644 > --- a/drivers/net/can/ifi_canfd/ifi_canfd.c > +++ b/drivers/net/can/ifi_canfd/ifi_canfd.c > @@ -774,10 +774,15 @@ static netdev_tx_t ifi_canfd_start_xmit(struct sk_buff *skb, > > if (priv->can.ctrlmode & (CAN_CTRLMODE_FD | CAN_CTRLMODE_FD_NON_ISO)) { > if (can_is_canfd_skb(skb)) { > + txdlc |= can_len2dlc(cf->len); > txdlc |= IFI_CANFD_TXFIFO_DLC_EDL; > if (cf->flags & CANFD_BRS) > txdlc |= IFI_CANFD_TXFIFO_DLC_BRS; > + } else { > + txdlc |= cf->len; > } > + } else { > + txdlc |= cf->len; > } Please use txdlc |= can_len2dlc(cf->len); by default (it works for CAN and CAN FD). So that it looks more like: txdlc |= can_len2dlc(cf->len); if ((priv->can.ctrlmode & CAN_CTRLMODE_FD) && can_is_canfd_skb(skb)) { txdlc |= IFI_CANFD_TXFIFO_DLC_EDL; if (cf->flags & CANFD_BRS) txdlc |= IFI_CANFD_TXFIFO_DLC_BRS; } Testing against CAN_CTRLMODE_FD_NON_ISO is wrong! This configuration bit is just for the protocol on the wire and is no distinction for CAN / CAN FD. Best regards, Oliver > > if (cf->can_id & CAN_RTR_FLAG) >
On 03/01/2016 07:11 PM, Oliver Hartkopp wrote: Hi! > On 02/29/2016 08:59 PM, Marek Vasut wrote: >> The TX DLC, the transmission length information, was not written >> into the transmit configuration register. When using the CAN core >> with different CAN controller, the receiving CAN controller will >> receive only the ID part of the CAN frame, but no data at all. >> >> This patch adds the TX DLC into the register to fix this issue. >> >> Signed-off-by: Marek Vasut <marex@denx.de> >> Cc: Marc Kleine-Budde <mkl@pengutronix.de> >> Cc: Mark Rutland <mark.rutland@arm.com> >> Cc: Oliver Hartkopp <socketcan@hartkopp.net> >> Cc: Wolfgang Grandegger <wg@grandegger.com> >> --- >> drivers/net/can/ifi_canfd/ifi_canfd.c | 5 +++++ >> 1 file changed, 5 insertions(+) >> >> diff --git a/drivers/net/can/ifi_canfd/ifi_canfd.c b/drivers/net/can/ifi_canfd/ifi_canfd.c >> index 72f5205..82a33bd 100644 >> --- a/drivers/net/can/ifi_canfd/ifi_canfd.c >> +++ b/drivers/net/can/ifi_canfd/ifi_canfd.c >> @@ -774,10 +774,15 @@ static netdev_tx_t ifi_canfd_start_xmit(struct sk_buff *skb, >> >> if (priv->can.ctrlmode & (CAN_CTRLMODE_FD | CAN_CTRLMODE_FD_NON_ISO)) { >> if (can_is_canfd_skb(skb)) { >> + txdlc |= can_len2dlc(cf->len); >> txdlc |= IFI_CANFD_TXFIFO_DLC_EDL; >> if (cf->flags & CANFD_BRS) >> txdlc |= IFI_CANFD_TXFIFO_DLC_BRS; >> + } else { >> + txdlc |= cf->len; >> } >> + } else { >> + txdlc |= cf->len; >> } > > Please use > > txdlc |= can_len2dlc(cf->len); > > by default (it works for CAN and CAN FD). > > So that it looks more like: > > txdlc |= can_len2dlc(cf->len); Roger. > if ((priv->can.ctrlmode & CAN_CTRLMODE_FD) && can_is_canfd_skb(skb)) { > txdlc |= IFI_CANFD_TXFIFO_DLC_EDL; > if (cf->flags & CANFD_BRS) > txdlc |= IFI_CANFD_TXFIFO_DLC_BRS; > } > > Testing against CAN_CTRLMODE_FD_NON_ISO is wrong! > This configuration bit is just for the protocol on the wire and is no > distinction for CAN / CAN FD. So CAN_CTRLMODE_FD is always set if the system operates in CAN/FD mode. And in addition to that, if the system operates in CAN/FD BOSCH mode, the CAN_CTRLMODE_FD_NON_ISO is set. Do I understand it correctly ? > Best regards, > Oliver > >> >> if (cf->can_id & CAN_RTR_FLAG) >>
On 03/01/2016 10:27 PM, Marek Vasut wrote: > On 03/01/2016 07:11 PM, Oliver Hartkopp wrote: > > Hi! > >> On 02/29/2016 08:59 PM, Marek Vasut wrote: >>> The TX DLC, the transmission length information, was not written >>> into the transmit configuration register. When using the CAN core >>> with different CAN controller, the receiving CAN controller will >>> receive only the ID part of the CAN frame, but no data at all. >>> >>> This patch adds the TX DLC into the register to fix this issue. >>> >>> Signed-off-by: Marek Vasut <marex@denx.de> >>> Cc: Marc Kleine-Budde <mkl@pengutronix.de> >>> Cc: Mark Rutland <mark.rutland@arm.com> >>> Cc: Oliver Hartkopp <socketcan@hartkopp.net> >>> Cc: Wolfgang Grandegger <wg@grandegger.com> >>> --- >>> drivers/net/can/ifi_canfd/ifi_canfd.c | 5 +++++ >>> 1 file changed, 5 insertions(+) >>> >>> diff --git a/drivers/net/can/ifi_canfd/ifi_canfd.c b/drivers/net/can/ifi_canfd/ifi_canfd.c >>> index 72f5205..82a33bd 100644 >>> --- a/drivers/net/can/ifi_canfd/ifi_canfd.c >>> +++ b/drivers/net/can/ifi_canfd/ifi_canfd.c >>> @@ -774,10 +774,15 @@ static netdev_tx_t ifi_canfd_start_xmit(struct sk_buff *skb, >>> >>> if (priv->can.ctrlmode & (CAN_CTRLMODE_FD | CAN_CTRLMODE_FD_NON_ISO)) { >>> if (can_is_canfd_skb(skb)) { >>> + txdlc |= can_len2dlc(cf->len); >>> txdlc |= IFI_CANFD_TXFIFO_DLC_EDL; >>> if (cf->flags & CANFD_BRS) >>> txdlc |= IFI_CANFD_TXFIFO_DLC_BRS; >>> + } else { >>> + txdlc |= cf->len; >>> } >>> + } else { >>> + txdlc |= cf->len; >>> } >> >> Please use >> >> txdlc |= can_len2dlc(cf->len); >> >> by default (it works for CAN and CAN FD). >> >> So that it looks more like: >> >> txdlc |= can_len2dlc(cf->len); > > Roger. > >> if ((priv->can.ctrlmode & CAN_CTRLMODE_FD) && can_is_canfd_skb(skb)) { >> txdlc |= IFI_CANFD_TXFIFO_DLC_EDL; >> if (cf->flags & CANFD_BRS) >> txdlc |= IFI_CANFD_TXFIFO_DLC_BRS; >> } >> >> Testing against CAN_CTRLMODE_FD_NON_ISO is wrong! >> This configuration bit is just for the protocol on the wire and is no >> distinction for CAN / CAN FD. > > So CAN_CTRLMODE_FD is always set if the system operates in CAN/FD mode. Not the 'system' but this specific CAN netdevice. > And in addition to that, if the system operates in CAN/FD BOSCH mode, > the CAN_CTRLMODE_FD_NON_ISO is set. Do I understand it correctly ? Yep! ('the CAN netdev') Regards, Oliver
On 03/02/2016 07:12 AM, Oliver Hartkopp wrote: > > > On 03/01/2016 10:27 PM, Marek Vasut wrote: >> On 03/01/2016 07:11 PM, Oliver Hartkopp wrote: >> >> Hi! >> >>> On 02/29/2016 08:59 PM, Marek Vasut wrote: >>>> The TX DLC, the transmission length information, was not written >>>> into the transmit configuration register. When using the CAN core >>>> with different CAN controller, the receiving CAN controller will >>>> receive only the ID part of the CAN frame, but no data at all. >>>> >>>> This patch adds the TX DLC into the register to fix this issue. >>>> >>>> Signed-off-by: Marek Vasut <marex@denx.de> >>>> Cc: Marc Kleine-Budde <mkl@pengutronix.de> >>>> Cc: Mark Rutland <mark.rutland@arm.com> >>>> Cc: Oliver Hartkopp <socketcan@hartkopp.net> >>>> Cc: Wolfgang Grandegger <wg@grandegger.com> >>>> --- >>>> drivers/net/can/ifi_canfd/ifi_canfd.c | 5 +++++ >>>> 1 file changed, 5 insertions(+) >>>> >>>> diff --git a/drivers/net/can/ifi_canfd/ifi_canfd.c b/drivers/net/can/ifi_canfd/ifi_canfd.c >>>> index 72f5205..82a33bd 100644 >>>> --- a/drivers/net/can/ifi_canfd/ifi_canfd.c >>>> +++ b/drivers/net/can/ifi_canfd/ifi_canfd.c >>>> @@ -774,10 +774,15 @@ static netdev_tx_t ifi_canfd_start_xmit(struct sk_buff *skb, >>>> >>>> if (priv->can.ctrlmode & (CAN_CTRLMODE_FD | CAN_CTRLMODE_FD_NON_ISO)) { >>>> if (can_is_canfd_skb(skb)) { >>>> + txdlc |= can_len2dlc(cf->len); >>>> txdlc |= IFI_CANFD_TXFIFO_DLC_EDL; >>>> if (cf->flags & CANFD_BRS) >>>> txdlc |= IFI_CANFD_TXFIFO_DLC_BRS; >>>> + } else { >>>> + txdlc |= cf->len; >>>> } >>>> + } else { >>>> + txdlc |= cf->len; >>>> } >>> >>> Please use >>> >>> txdlc |= can_len2dlc(cf->len); >>> >>> by default (it works for CAN and CAN FD). >>> >>> So that it looks more like: >>> >>> txdlc |= can_len2dlc(cf->len); >> >> Roger. >> >>> if ((priv->can.ctrlmode & CAN_CTRLMODE_FD) && can_is_canfd_skb(skb)) { >>> txdlc |= IFI_CANFD_TXFIFO_DLC_EDL; >>> if (cf->flags & CANFD_BRS) >>> txdlc |= IFI_CANFD_TXFIFO_DLC_BRS; >>> } >>> >>> Testing against CAN_CTRLMODE_FD_NON_ISO is wrong! >>> This configuration bit is just for the protocol on the wire and is no >>> distinction for CAN / CAN FD. >> >> So CAN_CTRLMODE_FD is always set if the system operates in CAN/FD mode. > > Not the 'system' but this specific CAN netdevice. Ooops, of course, sorry. >> And in addition to that, if the system operates in CAN/FD BOSCH mode, >> the CAN_CTRLMODE_FD_NON_ISO is set. Do I understand it correctly ? > > Yep! ('the CAN netdev') Thanks for the clarification!
diff --git a/drivers/net/can/ifi_canfd/ifi_canfd.c b/drivers/net/can/ifi_canfd/ifi_canfd.c index 72f5205..82a33bd 100644 --- a/drivers/net/can/ifi_canfd/ifi_canfd.c +++ b/drivers/net/can/ifi_canfd/ifi_canfd.c @@ -774,10 +774,15 @@ static netdev_tx_t ifi_canfd_start_xmit(struct sk_buff *skb, if (priv->can.ctrlmode & (CAN_CTRLMODE_FD | CAN_CTRLMODE_FD_NON_ISO)) { if (can_is_canfd_skb(skb)) { + txdlc |= can_len2dlc(cf->len); txdlc |= IFI_CANFD_TXFIFO_DLC_EDL; if (cf->flags & CANFD_BRS) txdlc |= IFI_CANFD_TXFIFO_DLC_BRS; + } else { + txdlc |= cf->len; } + } else { + txdlc |= cf->len; } if (cf->can_id & CAN_RTR_FLAG)
The TX DLC, the transmission length information, was not written into the transmit configuration register. When using the CAN core with different CAN controller, the receiving CAN controller will receive only the ID part of the CAN frame, but no data at all. This patch adds the TX DLC into the register to fix this issue. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Wolfgang Grandegger <wg@grandegger.com> --- drivers/net/can/ifi_canfd/ifi_canfd.c | 5 +++++ 1 file changed, 5 insertions(+)