@@ -74,6 +74,7 @@ struct pca9685 {
struct pwm_chip chip;
struct regmap *regmap;
int prescale;
+ bool staggered_outputs;
#if IS_ENABLED(CONFIG_GPIOLIB)
struct mutex lock;
struct gpio_chip gpio;
@@ -348,7 +349,7 @@ static int pca9685_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
{
struct pca9685 *pca = to_pca(chip);
unsigned long long duty, prescale;
- unsigned int reg;
+ unsigned int on, off, reg;
if (state->polarity != PWM_POLARITY_NORMAL)
return -EOPNOTSUPP;
@@ -395,6 +396,32 @@ static int pca9685_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
duty = (PCA9685_COUNTER_RANGE - 1) * state->duty_cycle;
duty = DIV_ROUND_UP_ULL(duty, state->period);
+ if (pca->staggered_outputs) {
+ if (pwm->hwpwm < PCA9685_MAXCHAN) {
+ /*
+ * To reduce EMI, the ON times of each channel are
+ * spread out evenly within the counter range, while
+ * still maintaining the configured duty cycle
+ */
+ on = pwm->hwpwm * PCA9685_COUNTER_RANGE /
+ PCA9685_MAXCHAN;
+ off = (on + duty) % PCA9685_COUNTER_RANGE;
+ regmap_write(pca->regmap, LED_N_ON_L(pwm->hwpwm),
+ on & 0xff);
+ regmap_write(pca->regmap, LED_N_ON_H(pwm->hwpwm),
+ (on >> 8) & 0xf);
+ regmap_write(pca->regmap, LED_N_OFF_L(pwm->hwpwm),
+ off & 0xff);
+ regmap_write(pca->regmap, LED_N_OFF_H(pwm->hwpwm),
+ (off >> 8) & 0xf);
+ return 0;
+ }
+
+ /* No staggering possible if "all LEDs" channel is used */
+ regmap_write(pca->regmap, PCA9685_ALL_LED_ON_L, 0);
+ regmap_write(pca->regmap, PCA9685_ALL_LED_ON_H, 0);
+ }
+
if (pwm->hwpwm >= PCA9685_MAXCHAN)
reg = PCA9685_ALL_LED_OFF_L;
else
@@ -494,6 +521,9 @@ static int pca9685_pwm_probe(struct i2c_client *client,
regmap_write(pca->regmap, PCA9685_MODE2, reg);
+ pca->staggered_outputs = device_property_read_bool(
+ &client->dev, "staggered-outputs");
+
/* Disable all LED ALLCALL and SUBx addresses to avoid bus collisions */
regmap_read(pca->regmap, PCA9685_MODE1, ®);
reg &= ~(MODE1_ALLCALL | MODE1_SUB1 | MODE1_SUB2 | MODE1_SUB3);
@@ -502,6 +532,9 @@ static int pca9685_pwm_probe(struct i2c_client *client,
/* Reset OFF registers to HW default (only full OFF bit is set) */
regmap_write(pca->regmap, PCA9685_ALL_LED_OFF_L, 0);
regmap_write(pca->regmap, PCA9685_ALL_LED_OFF_H, LED_FULL);
+ /* Reset ON registers to HW default */
+ regmap_write(pca->regmap, PCA9685_ALL_LED_ON_L, 0);
+ regmap_write(pca->regmap, PCA9685_ALL_LED_ON_H, 0);
pca->chip.ops = &pca9685_pwm_ops;
/* Add an extra channel for ALL_LED */
The PCA9685 supports staggered LED output ON times to minimize current surges and reduce EMI. When this new option is enabled, the ON times of each channel are delayed by channel number x counter range / 16, which avoids asserting all enabled outputs at the same counter value while still maintaining the configured duty cycle of each output. Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> --- drivers/pwm/pwm-pca9685.c | 35 ++++++++++++++++++++++++++++++++++- 1 file changed, 34 insertions(+), 1 deletion(-)