From patchwork Thu Aug 13 12:48:27 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1344259 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=WoPGR1l+; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BS5y828CHz9sTY for ; Thu, 13 Aug 2020 22:50:08 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1726773AbgHMMty (ORCPT ); Thu, 13 Aug 2020 08:49:54 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:55038 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1726604AbgHMMs5 (ORCPT ); Thu, 13 Aug 2020 08:48:57 -0400 Received: from ssl.serverraum.org (ssl.serverraum.org [IPv6:2a01:4f8:151:8464::1:2]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id D9109C061384; Thu, 13 Aug 2020 05:48:56 -0700 (PDT) Received: from mwalle01.sab.local. (unknown [213.135.10.150]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id C75BA23E49; Thu, 13 Aug 2020 14:48:54 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1597322935; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=CJgqjcuSVV7lxyxe2zgFsffHgSpz/scd2LODCYPpdIU=; b=WoPGR1l++ttoQPTeVK6oDAy29epwF7Mowss+21yVgny3JR42fnCSbf5iJS3A7OEo5OFd0R qROtWNCOrpHrAdhABj3LeVzNcpCSmdjhhS0jS9N0Fr4fvN717fqlaNNe/E+Cc9eictEcMn 0odAwXLeUm6W1RwAeG7Dk1cio9I8yVc= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v8 08/13] hwmon: add support for the sl28cpld hardware monitoring controller Date: Thu, 13 Aug 2020 14:48:27 +0200 Message-Id: <20200813124832.17349-9-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200813124832.17349-1-michael@walle.cc> References: <20200813124832.17349-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Add support for the hardware monitoring controller of the sl28cpld board management controller. This driver is part of a multi-function device. Signed-off-by: Michael Walle Acked-by: Guenter Roeck Reviewed-by: Andy Shevchenko --- Changes since v7: - added "depends on MFD_SL28CPLD || COMPILE_TEST" Changes since v6: - none Changes since v5: - none Changes since v4: - update copyright year - remove #include , suggested by Andy. - use PTR_ERR_OR_ZERO(), suggested by Andy. - remove the platform device table - don't use KBUID_MODNAME Changes since v3: - see cover letter Documentation/hwmon/index.rst | 1 + Documentation/hwmon/sl28cpld.rst | 36 ++++++++ drivers/hwmon/Kconfig | 10 +++ drivers/hwmon/Makefile | 1 + drivers/hwmon/sl28cpld-hwmon.c | 142 +++++++++++++++++++++++++++++++ 5 files changed, 190 insertions(+) create mode 100644 Documentation/hwmon/sl28cpld.rst create mode 100644 drivers/hwmon/sl28cpld-hwmon.c diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst index 750d3a975d82..d90c43c82936 100644 --- a/Documentation/hwmon/index.rst +++ b/Documentation/hwmon/index.rst @@ -154,6 +154,7 @@ Hardware Monitoring Kernel Drivers sht3x shtc1 sis5595 + sl28cpld smm665 smsc47b397 smsc47m192 diff --git a/Documentation/hwmon/sl28cpld.rst b/Documentation/hwmon/sl28cpld.rst new file mode 100644 index 000000000000..7ed65f78250c --- /dev/null +++ b/Documentation/hwmon/sl28cpld.rst @@ -0,0 +1,36 @@ +.. SPDX-License-Identifier: GPL-2.0-only + +Kernel driver sl28cpld +====================== + +Supported chips: + + * Kontron sl28cpld + + Prefix: 'sl28cpld' + + Datasheet: not available + +Authors: Michael Walle + +Description +----------- + +The sl28cpld is a board management controller which also exposes a hardware +monitoring controller. At the moment this controller supports a single fan +supervisor. In the future there might be other flavours and additional +hardware monitoring might be supported. + +The fan supervisor has a 7 bit counter register and a counter period of 1 +second. If the 7 bit counter overflows, the supervisor will automatically +switch to x8 mode to support a wider input range at the loss of +granularity. + +Sysfs entries +------------- + +The following attributes are supported. + +======================= ======================================================== +fan1_input Fan RPM. Assuming 2 pulses per revolution. +======================= ======================================================== diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 8dc28b26916e..d98c0a6860d1 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -1479,6 +1479,16 @@ config SENSORS_RASPBERRYPI_HWMON This driver can also be built as a module. If so, the module will be called raspberrypi-hwmon. +config SENSORS_SL28CPLD + tristate "Kontron sl28cpld hardware monitoring driver" + depends on MFD_SL28CPLD || COMPILE_TEST + help + If you say yes here you get support for the fan supervisor of the + sl28cpld board management controller. + + This driver can also be built as a module. If so, the module + will be called sl28cpld-hwmon. + config SENSORS_SHT15 tristate "Sensiron humidity and temperature sensors. SHT15 and compat." depends on GPIOLIB || COMPILE_TEST diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index a8f4b35b136b..dee8511f9348 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -159,6 +159,7 @@ obj-$(CONFIG_SENSORS_S3C) += s3c-hwmon.o obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o obj-$(CONFIG_SENSORS_SCH5627) += sch5627.o obj-$(CONFIG_SENSORS_SCH5636) += sch5636.o +obj-$(CONFIG_SENSORS_SL28CPLD) += sl28cpld-hwmon.o obj-$(CONFIG_SENSORS_SHT15) += sht15.o obj-$(CONFIG_SENSORS_SHT21) += sht21.o obj-$(CONFIG_SENSORS_SHT3x) += sht3x.o diff --git a/drivers/hwmon/sl28cpld-hwmon.c b/drivers/hwmon/sl28cpld-hwmon.c new file mode 100644 index 000000000000..e48f58ec5b9c --- /dev/null +++ b/drivers/hwmon/sl28cpld-hwmon.c @@ -0,0 +1,142 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * sl28cpld hardware monitoring driver + * + * Copyright 2020 Kontron Europe GmbH + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#define FAN_INPUT 0x00 +#define FAN_SCALE_X8 BIT(7) +#define FAN_VALUE_MASK GENMASK(6, 0) + +struct sl28cpld_hwmon { + struct regmap *regmap; + u32 offset; +}; + +static umode_t sl28cpld_hwmon_is_visible(const void *data, + enum hwmon_sensor_types type, + u32 attr, int channel) +{ + return 0444; +} + +static int sl28cpld_hwmon_read(struct device *dev, + enum hwmon_sensor_types type, u32 attr, + int channel, long *input) +{ + struct sl28cpld_hwmon *hwmon = dev_get_drvdata(dev); + unsigned int value; + int ret; + + switch (attr) { + case hwmon_fan_input: + ret = regmap_read(hwmon->regmap, hwmon->offset + FAN_INPUT, + &value); + if (ret) + return ret; + /* + * The register has a 7 bit value and 1 bit which indicates the + * scale. If the MSB is set, then the lower 7 bit has to be + * multiplied by 8, to get the correct reading. + */ + if (value & FAN_SCALE_X8) + value = FIELD_GET(FAN_VALUE_MASK, value) << 3; + + /* + * The counter period is 1000ms and the sysfs specification + * says we should asssume 2 pulses per revolution. + */ + value *= 60 / 2; + + break; + default: + return -EOPNOTSUPP; + } + + *input = value; + return 0; +} + +static const u32 sl28cpld_hwmon_fan_config[] = { + HWMON_F_INPUT, + 0 +}; + +static const struct hwmon_channel_info sl28cpld_hwmon_fan = { + .type = hwmon_fan, + .config = sl28cpld_hwmon_fan_config, +}; + +static const struct hwmon_channel_info *sl28cpld_hwmon_info[] = { + &sl28cpld_hwmon_fan, + NULL +}; + +static const struct hwmon_ops sl28cpld_hwmon_ops = { + .is_visible = sl28cpld_hwmon_is_visible, + .read = sl28cpld_hwmon_read, +}; + +static const struct hwmon_chip_info sl28cpld_hwmon_chip_info = { + .ops = &sl28cpld_hwmon_ops, + .info = sl28cpld_hwmon_info, +}; + +static int sl28cpld_hwmon_probe(struct platform_device *pdev) +{ + struct sl28cpld_hwmon *hwmon; + struct device *hwmon_dev; + int ret; + + if (!pdev->dev.parent) + return -ENODEV; + + hwmon = devm_kzalloc(&pdev->dev, sizeof(*hwmon), GFP_KERNEL); + if (!hwmon) + return -ENOMEM; + + hwmon->regmap = dev_get_regmap(pdev->dev.parent, NULL); + if (!hwmon->regmap) + return -ENODEV; + + ret = device_property_read_u32(&pdev->dev, "reg", &hwmon->offset); + if (ret) + return -EINVAL; + + hwmon_dev = devm_hwmon_device_register_with_info(&pdev->dev, + "sl28cpld_hwmon", hwmon, + &sl28cpld_hwmon_chip_info, NULL); + if (IS_ERR(hwmon_dev)) + dev_err(&pdev->dev, "failed to register as hwmon device"); + + return PTR_ERR_OR_ZERO(hwmon_dev); +} + +static const struct of_device_id sl28cpld_hwmon_of_match[] = { + { .compatible = "kontron,sl28cpld-fan" }, + {} +}; +MODULE_DEVICE_TABLE(of, sl28cpld_hwmon_of_match); + +static struct platform_driver sl28cpld_hwmon_driver = { + .probe = sl28cpld_hwmon_probe, + .driver = { + .name = "sl28cpld-fan", + .of_match_table = sl28cpld_hwmon_of_match, + }, +}; +module_platform_driver(sl28cpld_hwmon_driver); + +MODULE_DESCRIPTION("sl28cpld Hardware Monitoring Driver"); +MODULE_AUTHOR("Michael Walle "); +MODULE_LICENSE("GPL");