| Message ID | 20240301-x1e80100-pci-v4-1-7ab7e281d647@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | PCI: qcom: Add PCIe support for X1E80100 | expand |
On Fri, 01 Mar 2024 18:59:01 +0200, Abel Vesa wrote: > Add dedicated schema for the PCIe controllers found on X1E80100. > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org> > --- > .../bindings/pci/qcom,pcie-x1e80100.yaml | 165 +++++++++++++++++++++ > 1 file changed, 165 insertions(+) > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.yaml: Error in referenced schema matching $id: http://devicetree.org/schemas/pci/qcom,pcie-common.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.example.dtb: pcie@1c08000: False schema does not allow {'compatible': ['qcom,pcie-x1e80100'], 'reg': [[0, 29392896, 0, 12288], [0, 2080374784, 0, 3869], [0, 2080378688, 0, 168], [0, 2080378880, 0, 4096], [0, 2081423360, 0, 1048576], [0, 29405184, 0, 4096]], 'reg-names': ['parf', 'dbi', 'elbi', 'atu', 'config', 'mhi'], 'ranges': [[16777216, 0, 0, 0, 1612709888, 0, 1048576], [33554432, 0, 1613758464, 0, 1613758464, 0, 63963136]], 'bus-range': [[0, 255]], 'device_type': ['pci'], 'linux,pci-domain': [[0]], 'num-lanes': [[2]], '#address-cells': [[3]], '#size-cells': [[2]], 'clocks': [[4294967295, 96], [4294967295, 98], [4294967295, 99], [4294967295, 105], [4294967295, 106], [4294967295, 21], [4294967295, 33]], 'clock-names': ['aux', 'cfg', 'bus_master', 'bus_slave', 'slave_q2a', 'noc_aggr', 'cnoc_sf_axi'], 'dma-coherent': True, 'interrupts': [[0, 141, 4], [0, 142, 4], [0, 143, 4], [0, 144, 4], [ 0, 145, 4], [0, 146, 4], [0, 147, 4], [0, 148, 4]], 'interrupt-names': ['msi0', 'msi1', 'msi2', 'msi3', 'msi4', 'msi5', 'msi6', 'msi7'], '#interrupt-cells': [[1]], 'interrupt-map-mask': [[0, 0, 0, 7]], 'interrupt-map': [[0, 0, 0, 1, 4294967295, 0, 0, 0, 149, 4], [0, 0, 0, 2, 4294967295, 0, 0, 0, 150, 4], [0, 0, 0, 3, 4294967295, 0, 0, 0, 151, 4], [0, 0, 0, 4, 4294967295, 0, 0, 0, 152, 4]], 'interconnects': [[4294967295, 1, 0, 4294967295, 1, 0], [4294967295, 3, 0, 4294967295, 12, 0]], 'interconnect-names': ['pcie-mem', 'cpu-pcie'], 'iommu-map': [[0, 4294967295, 5120, 1], [256, 4294967295, 5121, 1]], 'phys': [[4294967295]], 'phy-names': ['pciephy'], 'pinctrl-0': [[4294967295]], 'pinctrl-names': ['default'], 'power-domains': [[4294967295, 5]], 'resets': [[4294967295, 24]], 'reset-names': ['pci'], 'perst-gpios': [[4294967295, 94, 1]], 'wake-gpios': [[4294967295, 96, 0]], '$nodename': ['pcie@1c08000']} from schema $id: http://devicetree.org/schemas/pci/qcom,pcie-x1e80100.yaml# /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.example.dtb: pcie@1c08000: Unevaluated properties are not allowed ('#address-cells', '#interrupt-cells', '#size-cells', 'bus-range', 'device_type', 'dma-coherent', 'interconnect-names', 'interconnects', 'interrupt-map', 'interrupt-map-mask', 'iommu-map', 'linux,pci-domain', 'num-lanes', 'perst-gpios', 'phy-names', 'phys', 'power-domains', 'ranges', 'wake-gpios' were unexpected) from schema $id: http://devicetree.org/schemas/pci/qcom,pcie-x1e80100.yaml# doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20240301-x1e80100-pci-v4-1-7ab7e281d647@linaro.org The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema.
On 01/03/2024 17:59, Abel Vesa wrote: > Add dedicated schema for the PCIe controllers found on X1E80100. > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org> > --- > .../bindings/pci/qcom,pcie-x1e80100.yaml | 165 +++++++++++++++++++++ > 1 file changed, 165 insertions(+) Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Failure reported by Rob's robot is coming from dependency in PCI tree. Best regards, Krzysztof
On Fri, Mar 01, 2024 at 06:59:01PM +0200, Abel Vesa wrote: > Add dedicated schema for the PCIe controllers found on X1E80100. > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> - Mani > --- > .../bindings/pci/qcom,pcie-x1e80100.yaml | 165 +++++++++++++++++++++ > 1 file changed, 165 insertions(+) > > diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.yaml > new file mode 100644 > index 000000000000..1074310a8e7a > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.yaml > @@ -0,0 +1,165 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pci/qcom,pcie-x1e80100.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Qualcomm X1E80100 PCI Express Root Complex > + > +maintainers: > + - Bjorn Andersson <andersson@kernel.org> > + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > + > +description: > + Qualcomm X1E80100 SoC (and compatible) PCIe root complex controller is based on > + the Synopsys DesignWare PCIe IP. > + > +properties: > + compatible: > + const: qcom,pcie-x1e80100 > + > + reg: > + minItems: 5 > + maxItems: 6 > + > + reg-names: > + minItems: 5 > + items: > + - const: parf # Qualcomm specific registers > + - const: dbi # DesignWare PCIe registers > + - const: elbi # External local bus interface registers > + - const: atu # ATU address space > + - const: config # PCIe configuration space > + - const: mhi # MHI registers > + > + clocks: > + minItems: 7 > + maxItems: 7 > + > + clock-names: > + items: > + - const: aux # Auxiliary clock > + - const: cfg # Configuration clock > + - const: bus_master # Master AXI clock > + - const: bus_slave # Slave AXI clock > + - const: slave_q2a # Slave Q2A clock > + - const: noc_aggr # Aggre NoC PCIe AXI clock > + - const: cnoc_sf_axi # Config NoC PCIe1 AXI clock > + > + interrupts: > + minItems: 8 > + maxItems: 8 > + > + interrupt-names: > + items: > + - const: msi0 > + - const: msi1 > + - const: msi2 > + - const: msi3 > + - const: msi4 > + - const: msi5 > + - const: msi6 > + - const: msi7 > + > + resets: > + minItems: 1 > + maxItems: 2 > + > + reset-names: > + minItems: 1 > + items: > + - const: pci # PCIe core reset > + - const: link_down # PCIe link down reset > + > +allOf: > + - $ref: qcom,pcie-common.yaml# > + > +unevaluatedProperties: false > + > +examples: > + - | > + #include <dt-bindings/clock/qcom,x1e80100-gcc.h> > + #include <dt-bindings/gpio/gpio.h> > + #include <dt-bindings/interconnect/qcom,x1e80100-rpmh.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + > + soc { > + #address-cells = <2>; > + #size-cells = <2>; > + > + pcie@1c08000 { > + compatible = "qcom,pcie-x1e80100"; > + reg = <0 0x01c08000 0 0x3000>, > + <0 0x7c000000 0 0xf1d>, > + <0 0x7c000f40 0 0xa8>, > + <0 0x7c001000 0 0x1000>, > + <0 0x7c100000 0 0x100000>, > + <0 0x01c0b000 0 0x1000>; > + reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi"; > + ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>, > + <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x3d00000>; > + > + bus-range = <0x00 0xff>; > + device_type = "pci"; > + linux,pci-domain = <0>; > + num-lanes = <2>; > + > + #address-cells = <3>; > + #size-cells = <2>; > + > + clocks = <&gcc GCC_PCIE_4_AUX_CLK>, > + <&gcc GCC_PCIE_4_CFG_AHB_CLK>, > + <&gcc GCC_PCIE_4_MSTR_AXI_CLK>, > + <&gcc GCC_PCIE_4_SLV_AXI_CLK>, > + <&gcc GCC_PCIE_4_SLV_Q2A_AXI_CLK>, > + <&gcc GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK>, > + <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>; > + clock-names = "aux", > + "cfg", > + "bus_master", > + "bus_slave", > + "slave_q2a", > + "noc_aggr", > + "cnoc_sf_axi"; > + > + dma-coherent; > + > + interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "msi0", "msi1", "msi2", "msi3", > + "msi4", "msi5", "msi6", "msi7"; > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 0x7>; > + interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ > + <0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ > + <0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ > + <0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ > + > + interconnects = <&pcie_noc MASTER_PCIE_4 0 &mc_virt SLAVE_EBI1 0>, > + <&gem_noc MASTER_APPSS_PROC 0 &cnoc_main SLAVE_PCIE_4 0>; > + interconnect-names = "pcie-mem", "cpu-pcie"; > + > + iommu-map = <0x0 &apps_smmu 0x1400 0x1>, > + <0x100 &apps_smmu 0x1401 0x1>; > + > + phys = <&pcie4_phy>; > + phy-names = "pciephy"; > + > + pinctrl-0 = <&pcie0_default_state>; > + pinctrl-names = "default"; > + > + power-domains = <&gcc GCC_PCIE_4_GDSC>; > + > + resets = <&gcc GCC_PCIE_4_BCR>; > + reset-names = "pci"; > + > + perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; > + wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>; > + }; > + }; > > -- > 2.34.1 >
diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.yaml new file mode 100644 index 000000000000..1074310a8e7a --- /dev/null +++ b/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.yaml @@ -0,0 +1,165 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pci/qcom,pcie-x1e80100.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm X1E80100 PCI Express Root Complex + +maintainers: + - Bjorn Andersson <andersson@kernel.org> + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +description: + Qualcomm X1E80100 SoC (and compatible) PCIe root complex controller is based on + the Synopsys DesignWare PCIe IP. + +properties: + compatible: + const: qcom,pcie-x1e80100 + + reg: + minItems: 5 + maxItems: 6 + + reg-names: + minItems: 5 + items: + - const: parf # Qualcomm specific registers + - const: dbi # DesignWare PCIe registers + - const: elbi # External local bus interface registers + - const: atu # ATU address space + - const: config # PCIe configuration space + - const: mhi # MHI registers + + clocks: + minItems: 7 + maxItems: 7 + + clock-names: + items: + - const: aux # Auxiliary clock + - const: cfg # Configuration clock + - const: bus_master # Master AXI clock + - const: bus_slave # Slave AXI clock + - const: slave_q2a # Slave Q2A clock + - const: noc_aggr # Aggre NoC PCIe AXI clock + - const: cnoc_sf_axi # Config NoC PCIe1 AXI clock + + interrupts: + minItems: 8 + maxItems: 8 + + interrupt-names: + items: + - const: msi0 + - const: msi1 + - const: msi2 + - const: msi3 + - const: msi4 + - const: msi5 + - const: msi6 + - const: msi7 + + resets: + minItems: 1 + maxItems: 2 + + reset-names: + minItems: 1 + items: + - const: pci # PCIe core reset + - const: link_down # PCIe link down reset + +allOf: + - $ref: qcom,pcie-common.yaml# + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,x1e80100-gcc.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interconnect/qcom,x1e80100-rpmh.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + pcie@1c08000 { + compatible = "qcom,pcie-x1e80100"; + reg = <0 0x01c08000 0 0x3000>, + <0 0x7c000000 0 0xf1d>, + <0 0x7c000f40 0 0xa8>, + <0 0x7c001000 0 0x1000>, + <0 0x7c100000 0 0x100000>, + <0 0x01c0b000 0 0x1000>; + reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi"; + ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>, + <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x3d00000>; + + bus-range = <0x00 0xff>; + device_type = "pci"; + linux,pci-domain = <0>; + num-lanes = <2>; + + #address-cells = <3>; + #size-cells = <2>; + + clocks = <&gcc GCC_PCIE_4_AUX_CLK>, + <&gcc GCC_PCIE_4_CFG_AHB_CLK>, + <&gcc GCC_PCIE_4_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_4_SLV_AXI_CLK>, + <&gcc GCC_PCIE_4_SLV_Q2A_AXI_CLK>, + <&gcc GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK>, + <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>; + clock-names = "aux", + "cfg", + "bus_master", + "bus_slave", + "slave_q2a", + "noc_aggr", + "cnoc_sf_axi"; + + dma-coherent; + + interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi0", "msi1", "msi2", "msi3", + "msi4", "msi5", "msi6", "msi7"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + interconnects = <&pcie_noc MASTER_PCIE_4 0 &mc_virt SLAVE_EBI1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc_main SLAVE_PCIE_4 0>; + interconnect-names = "pcie-mem", "cpu-pcie"; + + iommu-map = <0x0 &apps_smmu 0x1400 0x1>, + <0x100 &apps_smmu 0x1401 0x1>; + + phys = <&pcie4_phy>; + phy-names = "pciephy"; + + pinctrl-0 = <&pcie0_default_state>; + pinctrl-names = "default"; + + power-domains = <&gcc GCC_PCIE_4_GDSC>; + + resets = <&gcc GCC_PCIE_4_BCR>; + reset-names = "pci"; + + perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>; + }; + };
Add dedicated schema for the PCIe controllers found on X1E80100. Signed-off-by: Abel Vesa <abel.vesa@linaro.org> --- .../bindings/pci/qcom,pcie-x1e80100.yaml | 165 +++++++++++++++++++++ 1 file changed, 165 insertions(+)