[3/6] phy: qcom: Introduce PCIe UNIPHY 28LP driver

Add Qualcomm PCIe UNIPHY 28LP driver support present
in Qualcomm IPQ5018 SoC and the phy init sequence.

Signed-off-by: Nitheesh Sekar <quic_nsekar@quicinc.com>
---
 drivers/phy/qualcomm/Kconfig                  |  12 +
 drivers/phy/qualcomm/Makefile                 |   1 +
 .../phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c  | 336 ++++++++++++++++++
 3 files changed, 349 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c

On Tue, 3 Oct 2023 at 15:09, Nitheesh Sekar <quic_nsekar@quicinc.com> wrote:
>
> Add Qualcomm PCIe UNIPHY 28LP driver support present
> in Qualcomm IPQ5018 SoC and the phy init sequence.
>
> Signed-off-by: Nitheesh Sekar <quic_nsekar@quicinc.com>
> ---
>  drivers/phy/qualcomm/Kconfig                  |  12 +
>  drivers/phy/qualcomm/Makefile                 |   1 +
>  .../phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c  | 336 ++++++++++++++++++
>  3 files changed, 349 insertions(+)
>  create mode 100644 drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c
>
> diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
> index d891058b7c39..b7d37cd98f02 100644
> --- a/drivers/phy/qualcomm/Kconfig
> +++ b/drivers/phy/qualcomm/Kconfig
> @@ -154,6 +154,18 @@ config PHY_QCOM_M31_USB
>           management. This driver is required even for peripheral only or
>           host only mode configurations.
>
> +config PHY_QCOM_UNIPHY_PCIE_28LP
> +       bool "PCIE UNIPHY 28LP PHY driver"
> +       depends on ARCH_QCOM
> +       depends on HAS_IOMEM
> +       depends on OF
> +       select GENERIC_PHY
> +       help
> +         Enable this to support the PCIe UNIPHY 28LP phy transceiver that
> +         is used with PCIe controllers on Qualcomm IPQ5018 chips. It
> +         handles PHY initialization, clock management required after
> +         resetting the hardware and power management.
> +
>  config PHY_QCOM_USB_HS
>         tristate "Qualcomm USB HS PHY module"
>         depends on USB_ULPI_BUS
> diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
> index ffd609ac6233..31105cd17bc9 100644
> --- a/drivers/phy/qualcomm/Makefile
> +++ b/drivers/phy/qualcomm/Makefile
> @@ -17,6 +17,7 @@ obj-$(CONFIG_PHY_QCOM_QMP_USB_LEGACY) += phy-qcom-qmp-usb-legacy.o
>  obj-$(CONFIG_PHY_QCOM_QUSB2)           += phy-qcom-qusb2.o
>  obj-$(CONFIG_PHY_QCOM_SNPS_EUSB2)      += phy-qcom-snps-eusb2.o
>  obj-$(CONFIG_PHY_QCOM_EUSB2_REPEATER)  += phy-qcom-eusb2-repeater.o
> +obj-$(CONFIG_PHY_QCOM_UNIPHY_PCIE_28LP)        += phy-qcom-uniphy-pcie-28lp.o
>  obj-$(CONFIG_PHY_QCOM_USB_HS)          += phy-qcom-usb-hs.o
>  obj-$(CONFIG_PHY_QCOM_USB_HSIC)        += phy-qcom-usb-hsic.o
>  obj-$(CONFIG_PHY_QCOM_USB_HS_28NM)     += phy-qcom-usb-hs-28nm.o
> diff --git a/drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c b/drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c
> new file mode 100644
> index 000000000000..5ef6ae7276cf
> --- /dev/null
> +++ b/drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c
> @@ -0,0 +1,336 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (c) 2023, The Linux Foundation. All rights reserved.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/phy/phy.h>
> +#include <linux/reset.h>
> +#include <linux/of_device.h>
> +#include <linux/delay.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/regmap.h>
> +
> +#define PIPE_CLK_DELAY_MIN_US                  5000
> +#define PIPE_CLK_DELAY_MAX_US                  5100
> +#define CDR_CTRL_REG_1         0x80
> +#define CDR_CTRL_REG_2         0x84
> +#define CDR_CTRL_REG_3         0x88
> +#define CDR_CTRL_REG_4         0x8C
> +#define CDR_CTRL_REG_5         0x90
> +#define CDR_CTRL_REG_6         0x94
> +#define CDR_CTRL_REG_7         0x98
> +#define SSCG_CTRL_REG_1                0x9c
> +#define SSCG_CTRL_REG_2                0xa0
> +#define SSCG_CTRL_REG_3                0xa4
> +#define SSCG_CTRL_REG_4                0xa8
> +#define SSCG_CTRL_REG_5                0xac
> +#define SSCG_CTRL_REG_6                0xb0
> +#define PCS_INTERNAL_CONTROL_2 0x2d8
> +
> +#define PHY_MODE_FIXED         0x1
> +
> +enum qcom_uniphy_pcie_type {
> +       PHY_TYPE_PCIE = 1,
> +       PHY_TYPE_PCIE_GEN2,
> +       PHY_TYPE_PCIE_GEN3,
> +};
> +
> +struct uniphy_regs {
> +       unsigned int offset;
> +       unsigned int val;
> +};
> +
> +struct uniphy_pcie_data {

Please stick to a single symbol/struct prefix.

> +       int lanes;
> +       /* 2nd lane offset */
> +       int lane_offset;
> +       unsigned int phy_type;
> +       const struct uniphy_regs *init_seq;
> +       unsigned int init_seq_num;
> +};
> +
> +struct qcom_uniphy_pcie {
> +       struct phy phy;
> +       struct device *dev;
> +       const struct uniphy_pcie_data *data;
> +       struct clk_bulk_data *clks;
> +       int num_clks;
> +       struct reset_control *resets;
> +       void __iomem *base;
> +};
> +
> +#define        phy_to_dw_phy(x)        container_of((x), struct qca_uni_pcie_phy, phy)
> +
> +static const struct uniphy_regs ipq5018_regs[] = {
> +       {
> +               .offset = SSCG_CTRL_REG_4,
> +               .val = 0x1cb9,
> +       },
> +       {

"}, {", on the same line.

> +               .offset = SSCG_CTRL_REG_5,
> +               .val = 0x023a,
> +       },
> +       {
> +               .offset = SSCG_CTRL_REG_3,
> +               .val = 0xd360,
> +       },
> +       {
> +               .offset = SSCG_CTRL_REG_1,
> +               .val = 0x1,
> +       },
> +       {
> +               .offset = SSCG_CTRL_REG_2,
> +               .val = 0xeb,
> +       },
> +       {
> +               .offset = CDR_CTRL_REG_4,
> +               .val = 0x3f9,
> +       },
> +       {
> +               .offset = CDR_CTRL_REG_5,
> +               .val = 0x1c9,
> +       },
> +       {
> +               .offset = CDR_CTRL_REG_2,
> +               .val = 0x419,
> +       },
> +       {
> +               .offset = CDR_CTRL_REG_1,
> +               .val = 0x200,
> +       },
> +       {
> +               .offset = PCS_INTERNAL_CONTROL_2,
> +               .val = 0xf101,
> +       },
> +};
> +
> +static const struct uniphy_pcie_data ipq5018_2x2_data = {
> +       .lanes          = 2,
> +       .lane_offset    = 0x800,
> +       .phy_type       = PHY_TYPE_PCIE_GEN2,
> +       .init_seq       = ipq5018_regs,
> +       .init_seq_num   = ARRAY_SIZE(ipq5018_regs),
> +};
> +
> +static void qcom_uniphy_pcie_init(struct qcom_uniphy_pcie *phy)
> +{
> +       const struct uniphy_pcie_data *data = phy->data;
> +       const struct uniphy_regs *init_seq;
> +       void __iomem *base = phy->base;
> +       int lane = 0;
> +       int i;
> +
> +       while (lane != data->lanes) {

for (lane = 0; ...)

> +               init_seq = data->init_seq;
> +
> +               for (i = 0; i < data->init_seq_num; i++, init_seq++)
> +                       writel(init_seq->val, base + init_seq->offset);
> +
> +               if (data->lanes == 2)
> +                       base = base + data->lane_offset;

Drop the if(). Use +=.

> +
> +               lane++;
> +       }
> +}
> +
> +static int qcom_uniphy_pcie_power_off(struct phy *x)
> +{
> +       struct qcom_uniphy_pcie *phy = phy_get_drvdata(x);
> +
> +       reset_control_assert(phy->resets);
> +
> +       clk_bulk_disable_unprepare(phy->num_clks, phy->clks);

Judging from power_on(), the order should be opposite.

> +
> +       return 0;
> +}
> +
> +static int qcom_uniphy_pcie_power_on(struct phy *x)
> +{
> +       int ret;
> +       struct qcom_uniphy_pcie *phy = phy_get_drvdata(x);
> +
> +       ret = reset_control_assert(phy->resets);
> +       if (ret) {
> +               dev_err(phy->dev, "reset assert failed (%d)\n", ret);
> +               return ret;
> +       }
> +
> +       /*
> +        * Delay periods before and after reset deassert are working values
> +        * from downstream Codeaurora kernel
> +        */
> +       usleep_range(100, 150);
> +
> +       ret = reset_control_deassert(phy->resets);
> +       if (ret) {
> +               dev_err(phy->dev, "reset deassert failed (%d)\n", ret);
> +               return ret;
> +       }
> +
> +       usleep_range(PIPE_CLK_DELAY_MIN_US, PIPE_CLK_DELAY_MAX_US);
> +
> +       ret = clk_bulk_prepare_enable(phy->num_clks, phy->clks);
> +       if (ret) {
> +               dev_err(phy->dev, "clk prepare and enable failed %d\n", ret);
> +               return ret;

Shouldn't the reset be asserted again?

> +       }
> +
> +       usleep_range(30, 50);

In the same function you have one usleep_range with the defined
constants and another one using plain numbers. Could you please stick
to the uniform scheme?

> +
> +       qcom_uniphy_pcie_init(phy);
> +       return 0;
> +}
> +
> +static int qcom_uniphy_pcie_get_resources(struct platform_device *pdev,
> +                                         struct qcom_uniphy_pcie *phy)

inline it

> +{
> +       struct resource *res;
> +
> +       res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +       phy->base = devm_ioremap_resource(phy->dev, res);

devm_platform_get_and_ioremap_resource()

> +       if (IS_ERR(phy->base)) {
> +               dev_err(phy->dev, "cannot get phy registers\n");
> +               return PTR_ERR(phy->base);
> +       }
> +
> +       phy->num_clks = devm_clk_bulk_get_all(phy->dev, &phy->clks);
> +       if (phy->num_clks < 0)
> +               return phy->num_clks;
> +
> +       phy->resets = devm_reset_control_array_get_exclusive(phy->dev);
> +       if (IS_ERR(phy->resets))
> +               return PTR_ERR(phy->resets);
> +
> +       return 0;
> +}
> +
> +/*
> + * Register a fixed rate pipe clock.
> + *
> + * The <s>_pipe_clksrc generated by PHY goes to the GCC that gate
> + * controls it. The <s>_pipe_clk coming out of the GCC is requested
> + * by the PHY driver for its operations.
> + * We register the <s>_pipe_clksrc here. The gcc driver takes care
> + * of assigning this <s>_pipe_clksrc as parent to <s>_pipe_clk.
> + * Below picture shows this relationship.
> + *
> + *         +---------------+
> + *         |   PHY block   |<<---------------------------------------+
> + *         |               |                                         |
> + *         |   +-------+   |                   +-----+               |
> + *   I/P---^-->|  PLL  |---^--->pipe_clksrc--->| GCC |--->pipe_clk---+
> + *    clk  |   +-------+   |                   +-----+
> + *         +---------------+
> + */
> +static int phy_pipe_clk_register(struct qcom_uniphy_pcie  *phy,
> +                                struct device_node *np)
> +{
> +       struct clk_fixed_rate *fixed;
> +       struct clk_init_data init = { };
> +       int ret;
> +
> +       ret = of_property_read_string(np, "clock-output-names", &init.name);
> +       if (ret) {
> +               dev_err(phy->dev, "%pOFn: No clock-output-names\n", np);
> +               return ret;
> +       }

Can we drop clock-output-names please.

> +
> +       fixed = devm_kzalloc(phy->dev, sizeof(*fixed), GFP_KERNEL);
> +       if (!fixed)
> +               return -ENOMEM;
> +
> +       init.ops = &clk_fixed_rate_ops;
> +       fixed->fixed_rate = 125000000;
> +       fixed->hw.init = &init;
> +
> +       ret = devm_clk_hw_register(phy->dev, &fixed->hw);
> +       if (ret)
> +               return ret;

devm_clk_hw_register_fixed_rate().  Then the whole function can be inlined.

> +
> +       ret = devm_of_clk_add_hw_provider(phy->dev, of_clk_hw_simple_get,
> +                                         &fixed->hw);
> +       if (ret)
> +               return ret;
> +
> +       return 0;
> +}
> +
> +static const struct of_device_id qcom_uniphy_pcie_id_table[] = {
> +       {
> +               .compatible = "qcom,ipq5018-uniphy-pcie-gen2x2",

Bindings describe both 2x1 and 2x2 PHYs, but the driver supports only
2x2. Either of that should be fixed.


> +               .data = &ipq5018_2x2_data,
> +       },
> +       { /* Sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, qcom_uniphy_pcie_id_table);
> +
> +static const struct phy_ops pcie_ops = {
> +       .power_on       = qcom_uniphy_pcie_power_on,
> +       .power_off      = qcom_uniphy_pcie_power_off,
> +       .owner          = THIS_MODULE,
> +};
> +
> +static int qcom_uniphy_pcie_probe(struct platform_device *pdev)
> +{
> +       struct qcom_uniphy_pcie *phy;
> +       int ret;
> +       struct phy *generic_phy;
> +       struct phy_provider *phy_provider;
> +       struct device *dev = &pdev->dev;
> +       struct device_node *np = of_node_get(dev->of_node);
> +
> +       phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
> +       if (!phy)
> +               return -ENOMEM;
> +
> +       platform_set_drvdata(pdev, phy);
> +       phy->dev = &pdev->dev;
> +
> +       phy->data = of_device_get_match_data(dev);
> +       if (!phy->data)
> +               return -EINVAL;
> +
> +       ret = qcom_uniphy_pcie_get_resources(pdev, phy);
> +       if (ret < 0) {
> +               dev_err(&pdev->dev, "failed to get resources: %d\n", ret);
> +               return ret;
> +       }
> +
> +       ret = phy_pipe_clk_register(phy, np);
> +       if (ret)
> +               dev_err(&pdev->dev, "failed to register phy pipe clk\n");
> +
> +       generic_phy = devm_phy_create(phy->dev, NULL, &pcie_ops);
> +       if (IS_ERR(generic_phy))
> +               return PTR_ERR(generic_phy);
> +
> +       phy_set_drvdata(generic_phy, phy);
> +       phy_provider = devm_of_phy_provider_register(phy->dev,
> +                                                    of_phy_simple_xlate);
> +       if (IS_ERR(phy_provider))
> +               return PTR_ERR(phy_provider);
> +
> +       return 0;
> +}
> +
> +static struct platform_driver qcom_uniphy_pcie_driver = {
> +       .probe          = qcom_uniphy_pcie_probe,
> +       .driver         = {
> +               .name   = "qcom-uniphy-pcie",
> +               .owner  = THIS_MODULE,
> +               .of_match_table = qcom_uniphy_pcie_id_table,
> +       },
> +};
> +
> +module_platform_driver(qcom_uniphy_pcie_driver);
> +
> +MODULE_ALIAS("platform:qcom-uniphy-pcie");
> +MODULE_LICENSE("Dual BSD/GPL");
> +MODULE_DESCRIPTION("PCIE QCOM UNIPHY driver");
> --
> 2.17.1
>


--
With best wishes
Dmitry

On 03/10/2023 14:08, Nitheesh Sekar wrote:
> Add Qualcomm PCIe UNIPHY 28LP driver support present
> in Qualcomm IPQ5018 SoC and the phy init sequence.
> 
> Signed-off-by: Nitheesh Sekar <quic_nsekar@quicinc.com>
> ---

...

> +static int qcom_uniphy_pcie_probe(struct platform_device *pdev)
> +{
> +	struct qcom_uniphy_pcie *phy;
> +	int ret;
> +	struct phy *generic_phy;
> +	struct phy_provider *phy_provider;
> +	struct device *dev = &pdev->dev;
> +	struct device_node *np = of_node_get(dev->of_node);
> +
> +	phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
> +	if (!phy)
> +		return -ENOMEM;
> +
> +	platform_set_drvdata(pdev, phy);
> +	phy->dev = &pdev->dev;
> +
> +	phy->data = of_device_get_match_data(dev);
> +	if (!phy->data)
> +		return -EINVAL;
> +
> +	ret = qcom_uniphy_pcie_get_resources(pdev, phy);
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "failed to get resources: %d\n", ret);
> +		return ret;

Syntax is:
return dev_err_probe()


> +	}
> +
> +	ret = phy_pipe_clk_register(phy, np);
> +	if (ret)
> +		dev_err(&pdev->dev, "failed to register phy pipe clk\n");
> +
> +	generic_phy = devm_phy_create(phy->dev, NULL, &pcie_ops);
> +	if (IS_ERR(generic_phy))
> +		return PTR_ERR(generic_phy);
> +
> +	phy_set_drvdata(generic_phy, phy);
> +	phy_provider = devm_of_phy_provider_register(phy->dev,
> +						     of_phy_simple_xlate);
> +	if (IS_ERR(phy_provider))
> +		return PTR_ERR(phy_provider);
> +
> +	return 0;
> +}
> +
> +static struct platform_driver qcom_uniphy_pcie_driver = {
> +	.probe		= qcom_uniphy_pcie_probe,
> +	.driver		= {
> +		.name	= "qcom-uniphy-pcie",
> +		.owner	= THIS_MODULE,

Run coccinelle/coccicheck.

> +		.of_match_table = qcom_uniphy_pcie_id_table,
> +	},
> +};
> +
> +module_platform_driver(qcom_uniphy_pcie_driver);
> +
> +MODULE_ALIAS("platform:qcom-uniphy-pcie");

You should not need MODULE_ALIAS() in normal cases. If you need it,
usually it means your device ID table is wrong.


Best regards,
Krzysztof

On 03. 10. 2023. 14:08, Nitheesh Sekar wrote:
> Add Qualcomm PCIe UNIPHY 28LP driver support present
> in Qualcomm IPQ5018 SoC and the phy init sequence.
>
> Signed-off-by: Nitheesh Sekar <quic_nsekar@quicinc.com>
> ---
>   drivers/phy/qualcomm/Kconfig                  |  12 +
>   drivers/phy/qualcomm/Makefile                 |   1 +
>   .../phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c  | 336 ++++++++++++++++++
>   3 files changed, 349 insertions(+)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c
>
> diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
> index d891058b7c39..b7d37cd98f02 100644
> --- a/drivers/phy/qualcomm/Kconfig
> +++ b/drivers/phy/qualcomm/Kconfig
> @@ -154,6 +154,18 @@ config PHY_QCOM_M31_USB
>   	  management. This driver is required even for peripheral only or
>   	  host only mode configurations.
>   
> +config PHY_QCOM_UNIPHY_PCIE_28LP
> +	bool "PCIE UNIPHY 28LP PHY driver"
> +	depends on ARCH_QCOM
> +	depends on HAS_IOMEM
> +	depends on OF
> +	select GENERIC_PHY
> +	help
> +	  Enable this to support the PCIe UNIPHY 28LP phy transceiver that
> +	  is used with PCIe controllers on Qualcomm IPQ5018 chips. It
> +	  handles PHY initialization, clock management required after
> +	  resetting the hardware and power management.
> +
>   config PHY_QCOM_USB_HS
>   	tristate "Qualcomm USB HS PHY module"
>   	depends on USB_ULPI_BUS
> diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
> index ffd609ac6233..31105cd17bc9 100644
> --- a/drivers/phy/qualcomm/Makefile
> +++ b/drivers/phy/qualcomm/Makefile
> @@ -17,6 +17,7 @@ obj-$(CONFIG_PHY_QCOM_QMP_USB_LEGACY)	+= phy-qcom-qmp-usb-legacy.o
>   obj-$(CONFIG_PHY_QCOM_QUSB2)		+= phy-qcom-qusb2.o
>   obj-$(CONFIG_PHY_QCOM_SNPS_EUSB2)	+= phy-qcom-snps-eusb2.o
>   obj-$(CONFIG_PHY_QCOM_EUSB2_REPEATER)	+= phy-qcom-eusb2-repeater.o
> +obj-$(CONFIG_PHY_QCOM_UNIPHY_PCIE_28LP)	+= phy-qcom-uniphy-pcie-28lp.o
>   obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
>   obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
>   obj-$(CONFIG_PHY_QCOM_USB_HS_28NM)	+= phy-qcom-usb-hs-28nm.o
> diff --git a/drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c b/drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c
> new file mode 100644
> index 000000000000..5ef6ae7276cf
> --- /dev/null
> +++ b/drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c
> @@ -0,0 +1,336 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (c) 2023, The Linux Foundation. All rights reserved.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/phy/phy.h>
> +#include <linux/reset.h>
> +#include <linux/of_device.h>
> +#include <linux/delay.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/regmap.h>
> +
> +#define PIPE_CLK_DELAY_MIN_US			5000
> +#define PIPE_CLK_DELAY_MAX_US			5100
> +#define CDR_CTRL_REG_1		0x80
> +#define CDR_CTRL_REG_2		0x84
> +#define CDR_CTRL_REG_3		0x88
> +#define CDR_CTRL_REG_4		0x8C
> +#define CDR_CTRL_REG_5		0x90
> +#define CDR_CTRL_REG_6		0x94
> +#define CDR_CTRL_REG_7		0x98
> +#define SSCG_CTRL_REG_1		0x9c
> +#define SSCG_CTRL_REG_2		0xa0
> +#define SSCG_CTRL_REG_3		0xa4
> +#define SSCG_CTRL_REG_4		0xa8
> +#define SSCG_CTRL_REG_5		0xac
> +#define SSCG_CTRL_REG_6		0xb0
> +#define PCS_INTERNAL_CONTROL_2	0x2d8
> +
> +#define PHY_MODE_FIXED		0x1
> +
> +enum qcom_uniphy_pcie_type {
> +	PHY_TYPE_PCIE = 1,
> +	PHY_TYPE_PCIE_GEN2,
> +	PHY_TYPE_PCIE_GEN3,
> +};
> +
> +struct uniphy_regs {
> +	unsigned int offset;
> +	unsigned int val;
> +};
> +
> +struct uniphy_pcie_data {
> +	int lanes;
> +	/* 2nd lane offset */
> +	int lane_offset;
> +	unsigned int phy_type;
> +	const struct uniphy_regs *init_seq;
> +	unsigned int init_seq_num;
> +};
> +
> +struct qcom_uniphy_pcie {
> +	struct phy phy;
> +	struct device *dev;
> +	const struct uniphy_pcie_data *data;
> +	struct clk_bulk_data *clks;
> +	int num_clks;
> +	struct reset_control *resets;
> +	void __iomem *base;
> +};
> +
> +#define	phy_to_dw_phy(x)	container_of((x), struct qca_uni_pcie_phy, phy)
> +
> +static const struct uniphy_regs ipq5018_regs[] = {
> +	{
> +		.offset = SSCG_CTRL_REG_4,
> +		.val = 0x1cb9,
> +	},
> +	{
> +		.offset = SSCG_CTRL_REG_5,
> +		.val = 0x023a,
> +	},
> +	{
> +		.offset = SSCG_CTRL_REG_3,
> +		.val = 0xd360,
> +	},
> +	{
> +		.offset = SSCG_CTRL_REG_1,
> +		.val = 0x1,
> +	},
> +	{
> +		.offset = SSCG_CTRL_REG_2,
> +		.val = 0xeb,
> +	},
> +	{
> +		.offset = CDR_CTRL_REG_4,
> +		.val = 0x3f9,
> +	},
> +	{
> +		.offset = CDR_CTRL_REG_5,
> +		.val = 0x1c9,
> +	},
> +	{
> +		.offset = CDR_CTRL_REG_2,
> +		.val = 0x419,
> +	},
> +	{
> +		.offset = CDR_CTRL_REG_1,
> +		.val = 0x200,
> +	},
> +	{
> +		.offset = PCS_INTERNAL_CONTROL_2,
> +		.val = 0xf101,
> +	},
> +};
> +
> +static const struct uniphy_pcie_data ipq5018_2x2_data = {
> +	.lanes		= 2,
> +	.lane_offset	= 0x800,
> +	.phy_type	= PHY_TYPE_PCIE_GEN2,
> +	.init_seq	= ipq5018_regs,
> +	.init_seq_num	= ARRAY_SIZE(ipq5018_regs),
> +};
> +
> +static void qcom_uniphy_pcie_init(struct qcom_uniphy_pcie *phy)
> +{
> +	const struct uniphy_pcie_data *data = phy->data;
> +	const struct uniphy_regs *init_seq;
> +	void __iomem *base = phy->base;
> +	int lane = 0;
> +	int i;
> +
> +	while (lane != data->lanes) {
> +		init_seq = data->init_seq;
> +
> +		for (i = 0; i < data->init_seq_num; i++, init_seq++)
> +			writel(init_seq->val, base + init_seq->offset);
> +
> +		if (data->lanes == 2)
> +			base = base + data->lane_offset;
> +
> +		lane++;
> +	}
> +}
> +
> +static int qcom_uniphy_pcie_power_off(struct phy *x)
> +{
> +	struct qcom_uniphy_pcie *phy = phy_get_drvdata(x);
> +
> +	reset_control_assert(phy->resets);
> +
> +	clk_bulk_disable_unprepare(phy->num_clks, phy->clks);
> +
> +	return 0;
> +}
> +
> +static int qcom_uniphy_pcie_power_on(struct phy *x)
> +{
> +	int ret;
> +	struct qcom_uniphy_pcie *phy = phy_get_drvdata(x);
> +
> +	ret = reset_control_assert(phy->resets);
> +	if (ret) {
> +		dev_err(phy->dev, "reset assert failed (%d)\n", ret);
> +		return ret;
> +	}
> +
> +	/*
> +	 * Delay periods before and after reset deassert are working values
> +	 * from downstream Codeaurora kernel
> +	 */
> +	usleep_range(100, 150);
> +
> +	ret = reset_control_deassert(phy->resets);
> +	if (ret) {
> +		dev_err(phy->dev, "reset deassert failed (%d)\n", ret);
> +		return ret;
> +	}
> +
> +	usleep_range(PIPE_CLK_DELAY_MIN_US, PIPE_CLK_DELAY_MAX_US);
> +
> +	ret = clk_bulk_prepare_enable(phy->num_clks, phy->clks);
> +	if (ret) {
> +		dev_err(phy->dev, "clk prepare and enable failed %d\n", ret);
> +		return ret;
> +	}
> +
> +	usleep_range(30, 50);
> +
> +	qcom_uniphy_pcie_init(phy);
> +	return 0;
> +}
> +
> +static int qcom_uniphy_pcie_get_resources(struct platform_device *pdev,
> +					  struct qcom_uniphy_pcie *phy)
> +{
> +	struct resource *res;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	phy->base = devm_ioremap_resource(phy->dev, res);
> +	if (IS_ERR(phy->base)) {
> +		dev_err(phy->dev, "cannot get phy registers\n");
> +		return PTR_ERR(phy->base);
> +	}
> +
> +	phy->num_clks = devm_clk_bulk_get_all(phy->dev, &phy->clks);
> +	if (phy->num_clks < 0)
> +		return phy->num_clks;
> +
> +	phy->resets = devm_reset_control_array_get_exclusive(phy->dev);
> +	if (IS_ERR(phy->resets))
> +		return PTR_ERR(phy->resets);
> +
> +	return 0;
> +}
> +
> +/*
> + * Register a fixed rate pipe clock.
> + *
> + * The <s>_pipe_clksrc generated by PHY goes to the GCC that gate
> + * controls it. The <s>_pipe_clk coming out of the GCC is requested
> + * by the PHY driver for its operations.
> + * We register the <s>_pipe_clksrc here. The gcc driver takes care
> + * of assigning this <s>_pipe_clksrc as parent to <s>_pipe_clk.
> + * Below picture shows this relationship.
> + *
> + *         +---------------+
> + *         |   PHY block   |<<---------------------------------------+
> + *         |               |                                         |
> + *         |   +-------+   |                   +-----+               |
> + *   I/P---^-->|  PLL  |---^--->pipe_clksrc--->| GCC |--->pipe_clk---+
> + *    clk  |   +-------+   |                   +-----+
> + *         +---------------+
> + */
> +static int phy_pipe_clk_register(struct qcom_uniphy_pcie  *phy,
> +				 struct device_node *np)
> +{
> +	struct clk_fixed_rate *fixed;
> +	struct clk_init_data init = { };
> +	int ret;
> +
> +	ret = of_property_read_string(np, "clock-output-names", &init.name);
> +	if (ret) {
> +		dev_err(phy->dev, "%pOFn: No clock-output-names\n", np);
> +		return ret;
> +	}
> +
> +	fixed = devm_kzalloc(phy->dev, sizeof(*fixed), GFP_KERNEL);
> +	if (!fixed)
> +		return -ENOMEM;
> +
> +	init.ops = &clk_fixed_rate_ops;
> +	fixed->fixed_rate = 125000000;
> +	fixed->hw.init = &init;
> +
> +	ret = devm_clk_hw_register(phy->dev, &fixed->hw);
> +	if (ret)
> +		return ret;
> +
> +	ret = devm_of_clk_add_hw_provider(phy->dev, of_clk_hw_simple_get,
> +					  &fixed->hw);
> +	if (ret)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id qcom_uniphy_pcie_id_table[] = {
> +	{
> +		.compatible = "qcom,ipq5018-uniphy-pcie-gen2x2",
> +		.data = &ipq5018_2x2_data,

Hi, did you also forget the single lane PHY?
As you have the "qcom,ipq5018-uniphy-pcie-gen2x1" compatible used later 
in the DTS
but its not implemented in the driver at all.

Regards,
Robert

> +	},
> +	{ /* Sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, qcom_uniphy_pcie_id_table);
> +
> +static const struct phy_ops pcie_ops = {
> +	.power_on	= qcom_uniphy_pcie_power_on,
> +	.power_off	= qcom_uniphy_pcie_power_off,
> +	.owner          = THIS_MODULE,
> +};
> +
> +static int qcom_uniphy_pcie_probe(struct platform_device *pdev)
> +{
> +	struct qcom_uniphy_pcie *phy;
> +	int ret;
> +	struct phy *generic_phy;
> +	struct phy_provider *phy_provider;
> +	struct device *dev = &pdev->dev;
> +	struct device_node *np = of_node_get(dev->of_node);
> +
> +	phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
> +	if (!phy)
> +		return -ENOMEM;
> +
> +	platform_set_drvdata(pdev, phy);
> +	phy->dev = &pdev->dev;
> +
> +	phy->data = of_device_get_match_data(dev);
> +	if (!phy->data)
> +		return -EINVAL;
> +
> +	ret = qcom_uniphy_pcie_get_resources(pdev, phy);
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "failed to get resources: %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = phy_pipe_clk_register(phy, np);
> +	if (ret)
> +		dev_err(&pdev->dev, "failed to register phy pipe clk\n");
> +
> +	generic_phy = devm_phy_create(phy->dev, NULL, &pcie_ops);
> +	if (IS_ERR(generic_phy))
> +		return PTR_ERR(generic_phy);
> +
> +	phy_set_drvdata(generic_phy, phy);
> +	phy_provider = devm_of_phy_provider_register(phy->dev,
> +						     of_phy_simple_xlate);
> +	if (IS_ERR(phy_provider))
> +		return PTR_ERR(phy_provider);
> +
> +	return 0;
> +}
> +
> +static struct platform_driver qcom_uniphy_pcie_driver = {
> +	.probe		= qcom_uniphy_pcie_probe,
> +	.driver		= {
> +		.name	= "qcom-uniphy-pcie",
> +		.owner	= THIS_MODULE,
> +		.of_match_table = qcom_uniphy_pcie_id_table,
> +	},
> +};
> +
> +module_platform_driver(qcom_uniphy_pcie_driver);
> +
> +MODULE_ALIAS("platform:qcom-uniphy-pcie");
> +MODULE_LICENSE("Dual BSD/GPL");
> +MODULE_DESCRIPTION("PCIE QCOM UNIPHY driver");

On 10/4/2023 1:43 PM, Krzysztof Kozlowski wrote:
> On 03/10/2023 14:08, Nitheesh Sekar wrote:
>> Add Qualcomm PCIe UNIPHY 28LP driver support present
>> in Qualcomm IPQ5018 SoC and the phy init sequence.
>>
>> Signed-off-by: Nitheesh Sekar <quic_nsekar@quicinc.com>
>> ---
> ...
>
>> +static int qcom_uniphy_pcie_probe(struct platform_device *pdev)
>> +{
>> +	struct qcom_uniphy_pcie *phy;
>> +	int ret;
>> +	struct phy *generic_phy;
>> +	struct phy_provider *phy_provider;
>> +	struct device *dev = &pdev->dev;
>> +	struct device_node *np = of_node_get(dev->of_node);
>> +
>> +	phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
>> +	if (!phy)
>> +		return -ENOMEM;
>> +
>> +	platform_set_drvdata(pdev, phy);
>> +	phy->dev = &pdev->dev;
>> +
>> +	phy->data = of_device_get_match_data(dev);
>> +	if (!phy->data)
>> +		return -EINVAL;
>> +
>> +	ret = qcom_uniphy_pcie_get_resources(pdev, phy);
>> +	if (ret < 0) {
>> +		dev_err(&pdev->dev, "failed to get resources: %d\n", ret);
>> +		return ret;
> Syntax is:
> return dev_err_probe()
Sure. will update it and take care of this in future.
>
>
>> +	}
>> +
>> +	ret = phy_pipe_clk_register(phy, np);
>> +	if (ret)
>> +		dev_err(&pdev->dev, "failed to register phy pipe clk\n");
>> +
>> +	generic_phy = devm_phy_create(phy->dev, NULL, &pcie_ops);
>> +	if (IS_ERR(generic_phy))
>> +		return PTR_ERR(generic_phy);
>> +
>> +	phy_set_drvdata(generic_phy, phy);
>> +	phy_provider = devm_of_phy_provider_register(phy->dev,
>> +						     of_phy_simple_xlate);
>> +	if (IS_ERR(phy_provider))
>> +		return PTR_ERR(phy_provider);
>> +
>> +	return 0;
>> +}
>> +
>> +static struct platform_driver qcom_uniphy_pcie_driver = {
>> +	.probe		= qcom_uniphy_pcie_probe,
>> +	.driver		= {
>> +		.name	= "qcom-uniphy-pcie",
>> +		.owner	= THIS_MODULE,
> Run coccinelle/coccicheck.
Sure. Will do it.
>
>> +		.of_match_table = qcom_uniphy_pcie_id_table,
>> +	},
>> +};
>> +
>> +module_platform_driver(qcom_uniphy_pcie_driver);
>> +
>> +MODULE_ALIAS("platform:qcom-uniphy-pcie");
> You should not need MODULE_ALIAS() in normal cases. If you need it,
> usually it means your device ID table is wrong.
Ok. Will remove it.

Thanks,
Nitheesh