From patchwork Mon Dec 23 21:45:27 2019 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Remi Pommarel X-Patchwork-Id: 1215078 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=none (no SPF record) smtp.mailfrom=vger.kernel.org (client-ip=209.132.180.67; helo=vger.kernel.org; envelope-from=linux-pci-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=triplefau.lt Received: from vger.kernel.org (vger.kernel.org [209.132.180.67]) by ozlabs.org (Postfix) with ESMTP id 47hXlP52NBz9s4Y for ; Tue, 24 Dec 2019 08:38:09 +1100 (AEDT) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1726924AbfLWViJ (ORCPT ); Mon, 23 Dec 2019 16:38:09 -0500 Received: from relay10.mail.gandi.net ([217.70.178.230]:35409 "EHLO relay10.mail.gandi.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1726817AbfLWViI (ORCPT ); Mon, 23 Dec 2019 16:38:08 -0500 Received: from localhost (unknown [88.190.179.123]) (Authenticated sender: repk@triplefau.lt) by relay10.mail.gandi.net (Postfix) with ESMTPSA id 90219240007; Mon, 23 Dec 2019 21:38:03 +0000 (UTC) From: Remi Pommarel To: Kishon Vijay Abraham I , Yue Wang , Lorenzo Pieralisi , Andrew Murray , Kevin Hilman , Martin Blumenstingl , Neil Armstrong Cc: Jerome Brunet , linux-kernel@vger.kernel.org, linux-pci@vger.kernel.org, linux-amlogic@lists.infradead.org, Remi Pommarel Subject: [PATCH v2 1/3] phy: amlogic: Add Amlogic AXG MIPI/PCIE PHY Driver Date: Mon, 23 Dec 2019 22:45:27 +0100 Message-Id: <20191223214529.20377-2-repk@triplefau.lt> X-Mailer: git-send-email 2.24.0 In-Reply-To: <20191223214529.20377-1-repk@triplefau.lt> References: <20191223214529.20377-1-repk@triplefau.lt> MIME-Version: 1.0 Sender: linux-pci-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pci@vger.kernel.org This adds support for the MIPI PHY also needed for PCIE found in the Amlogic AXG SoC Family. MIPI or PCIE selection is done by the #phy-cells, making the mode static and exclusive. For now only PCIE fonctionality is supported. This PHY will be used to replace the mipi_enable clock gating logic which was mistakenly added in the clock subsystem. This also activate a non documented band gap bit in those registers that allows reliable PCIE clock signal generation on AXG platforms. Signed-off-by: Remi Pommarel --- drivers/phy/amlogic/Kconfig | 11 ++ drivers/phy/amlogic/Makefile | 1 + drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c | 176 ++++++++++++++++++ 3 files changed, 188 insertions(+) create mode 100644 drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig index af774ac2b934..1eeb75d018e3 100644 --- a/drivers/phy/amlogic/Kconfig +++ b/drivers/phy/amlogic/Kconfig @@ -59,3 +59,14 @@ config PHY_MESON_G12A_USB3_PCIE Enable this to support the Meson USB3 + PCIE Combo PHY found in Meson G12A SoCs. If unsure, say N. + +config PHY_MESON_AXG_MIPI_PCIE + tristate "Meson AXG MIPI + PCIE PHY driver" + default ARCH_MESON + depends on OF && (ARCH_MESON || COMPILE_TEST) + select GENERIC_PHY + select MFD_SYSCON + help + Enable this to support the Meson MIPI + PCIE PHY found + in Meson AXG SoCs. + If unsure, say N. diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile index 11d1c42ac2be..2167330a0ae8 100644 --- a/drivers/phy/amlogic/Makefile +++ b/drivers/phy/amlogic/Makefile @@ -4,3 +4,4 @@ obj-$(CONFIG_PHY_MESON_GXL_USB2) += phy-meson-gxl-usb2.o obj-$(CONFIG_PHY_MESON_G12A_USB2) += phy-meson-g12a-usb2.o obj-$(CONFIG_PHY_MESON_GXL_USB3) += phy-meson-gxl-usb3.o obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE) += phy-meson-g12a-usb3-pcie.o +obj-$(CONFIG_PHY_MESON_AXG_MIPI_PCIE) += phy-meson-axg-mipi-pcie.o diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c new file mode 100644 index 000000000000..006aa8cdfc47 --- /dev/null +++ b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c @@ -0,0 +1,176 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Amlogic AXG MIPI + PCIE PHY driver + * + * Copyright (C) 2019 Remi Pommarel + */ +#include +#include +#include +#include +#include +#include + +#define HHI_MIPI_CNTL0 0x00 +#define HHI_MIPI_CNTL0_COMMON_BLOCK GENMASK(31, 28) +#define HHI_MIPI_CNTL0_ENABLE BIT(29) +#define HHI_MIPI_CNTL0_BANDGAP BIT(26) +#define HHI_MIPI_CNTL0_DECODE_TO_RTERM GENMASK(15, 12) +#define HHI_MIPI_CNTL0_OUTPUT_EN BIT(3) + +#define HHI_MIPI_CNTL1 0x01 +#define HHI_MIPI_CNTL1_CH0_CML_PDR_EN BIT(12) +#define HHI_MIPI_CNTL1_LP_ABILITY GENMASK(5, 4) +#define HHI_MIPI_CNTL1_LP_RESISTER BIT(3) +#define HHI_MIPI_CNTL1_INPUT_SETTING BIT(2) +#define HHI_MIPI_CNTL1_INPUT_SEL BIT(1) +#define HHI_MIPI_CNTL1_PRBS7_EN BIT(0) + +#define HHI_MIPI_CNTL2 0x02 +#define HHI_MIPI_CNTL2_CH_PU GENMASK(31, 25) +#define HHI_MIPI_CNTL2_CH_CTL GENMASK(24, 19) +#define HHI_MIPI_CNTL2_CH0_DIGDR_EN BIT(18) +#define HHI_MIPI_CNTL2_CH_DIGDR_EN BIT(17) +#define HHI_MIPI_CNTL2_LPULPS_EN BIT(16) +#define HHI_MIPI_CNTL2_CH_EN(n) BIT(15 - (n)) +#define HHI_MIPI_CNTL2_CH0_LP_CTL GENMASK(10, 1) + +struct phy_axg_mipi_pcie_priv { + struct phy *phy; + unsigned int mode; + struct regmap *regmap; +}; + +static const struct regmap_config phy_axg_mipi_pcie_regmap_conf = { + .reg_bits = 8, + .val_bits = 32, + .reg_stride = 4, + .max_register = HHI_MIPI_CNTL2, +}; + +static int phy_axg_mipi_pcie_power_on(struct phy *phy) +{ + struct phy_axg_mipi_pcie_priv *priv = phy_get_drvdata(phy); + + /* MIPI not supported yet */ + if (priv->mode != PHY_TYPE_PCIE) + return 0; + + regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0, + HHI_MIPI_CNTL0_BANDGAP, HHI_MIPI_CNTL0_BANDGAP); + + regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0, + HHI_MIPI_CNTL0_ENABLE, HHI_MIPI_CNTL0_ENABLE); + return 0; +} + +static int phy_axg_mipi_pcie_power_off(struct phy *phy) +{ + struct phy_axg_mipi_pcie_priv *priv = phy_get_drvdata(phy); + + /* MIPI not supported yet */ + if (priv->mode != PHY_TYPE_PCIE) + return 0; + + regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0, + HHI_MIPI_CNTL0_BANDGAP, 0); + regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0, + HHI_MIPI_CNTL0_ENABLE, 0); + return 0; +} + +static int phy_axg_mipi_pcie_init(struct phy *phy) +{ + return 0; +} + +static int phy_axg_mipi_pcie_exit(struct phy *phy) +{ + return 0; +} + +static const struct phy_ops phy_axg_mipi_pcie_ops = { + .init = phy_axg_mipi_pcie_init, + .exit = phy_axg_mipi_pcie_exit, + .power_on = phy_axg_mipi_pcie_power_on, + .power_off = phy_axg_mipi_pcie_power_off, + .owner = THIS_MODULE, +}; + +static struct phy *phy_axg_mipi_pcie_xlate(struct device *dev, + struct of_phandle_args *args) +{ + struct phy_axg_mipi_pcie_priv *priv = dev_get_drvdata(dev); + unsigned int mode; + + if (args->args_count != 1) { + dev_err(dev, "invalid number of arguments\n"); + return ERR_PTR(-EINVAL); + } + + mode = args->args[0]; + + /* MIPI mode is not supported yet */ + if (mode != PHY_TYPE_PCIE) { + dev_err(dev, "invalid phy mode select argument\n"); + return ERR_PTR(-EINVAL); + } + + priv->mode = mode; + return priv->phy; +} + +static int phy_axg_mipi_pcie_probe(struct platform_device *pdev) +{ + struct phy_provider *pphy; + struct device *dev = &pdev->dev; + struct phy_axg_mipi_pcie_priv *priv; + struct device_node *np = dev->of_node; + int ret; + + priv = devm_kmalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + /* Get the hhi system controller node */ + priv->regmap = syscon_node_to_regmap(of_get_parent(dev->of_node)); + if (IS_ERR(priv->regmap)) { + dev_err(dev, "failed to get HHI regmap\n"); + return PTR_ERR(priv->regmap); + } + + priv->phy = devm_phy_create(dev, np, &phy_axg_mipi_pcie_ops); + if (IS_ERR(priv->phy)) { + ret = PTR_ERR(priv->phy); + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to create PHY\n"); + return ret; + } + + phy_set_drvdata(priv->phy, priv); + dev_set_drvdata(dev, priv); + pphy = devm_of_phy_provider_register(dev, phy_axg_mipi_pcie_xlate); + + return PTR_ERR_OR_ZERO(pphy); +} + +static const struct of_device_id phy_axg_mipi_pcie_of_match[] = { + { + .compatible = "amlogic,axg-mipi-pcie-phy", + }, + { }, +}; +MODULE_DEVICE_TABLE(of, phy_axg_mipi_pcie_of_match); + +static struct platform_driver phy_axg_mipi_pcie_driver = { + .probe = phy_axg_mipi_pcie_probe, + .driver = { + .name = "phy-axg-mipi-pcie", + .of_match_table = phy_axg_mipi_pcie_of_match, + }, +}; +module_platform_driver(phy_axg_mipi_pcie_driver); + +MODULE_AUTHOR("Remi Pommarel "); +MODULE_DESCRIPTION("Amlogic AXG MIPI + PCIE PHY driver"); +MODULE_LICENSE("GPL v2");