| Message ID | 1353294849-22588-1-git-send-email-ying.huang@intel.com |
|---|---|
| State | Superseded |
| Headers | show |
On Mon, 19 Nov 2012, Huang Ying wrote: > For unbound PCI devices, what we need is: > > - Always in D0 state, because some devices does not work again after > being put into D3 by the PCI bus. > > - In SUSPENDED state if allowed, so that the parent devices can still > be put into low power state. > > To satisfy these requirement, the runtime PM for the unbound PCI > devices are disabled and set to SUSPENDED state. One issue of this > solution is that the PCI devices will be put into SUSPENDED state even > if the SUSPENDED state is forbidden via the sysfs interface > (.../power/control) of the device. This is not an issue for most > devices, because most PCI devices are not used at all if unbounded. > But there are exceptions. For example, unbound VGA card can be used > for display, but suspend its parents make it stop working. > > To fix the issue, we keep the runtime PM enabled when the PCI devices > are unbound. But the runtime PM callbacks will do nothing if the PCI > devices are unbound. This way, we can put the PCI devices into > SUSPENDED state without put the PCI devices into D3 state. > > Known issue: after some changing, pci_dev->driver is used to indicate > whether the PCI devices are bound and whether the runtime PM callbacks > should do nothing. Maybe it is better to use a dedicated flag such as > .skip_rtpm_callbacks. That may improve code readability. I think it's okay like this, especially if you add a comment in pci_runtime_suspend, pci_runtime_resume, and pci_runtime_idle explaining that when pci_dev->driver isn't set, the device should always remain in D0 regardless of the runtime status. Alan Stern -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Monday, November 19, 2012 11:31:01 AM Alan Stern wrote: > On Mon, 19 Nov 2012, Huang Ying wrote: > > > For unbound PCI devices, what we need is: > > > > - Always in D0 state, because some devices does not work again after > > being put into D3 by the PCI bus. > > > > - In SUSPENDED state if allowed, so that the parent devices can still > > be put into low power state. > > > > To satisfy these requirement, the runtime PM for the unbound PCI > > devices are disabled and set to SUSPENDED state. One issue of this > > solution is that the PCI devices will be put into SUSPENDED state even > > if the SUSPENDED state is forbidden via the sysfs interface > > (.../power/control) of the device. This is not an issue for most > > devices, because most PCI devices are not used at all if unbounded. > > But there are exceptions. For example, unbound VGA card can be used > > for display, but suspend its parents make it stop working. > > > > To fix the issue, we keep the runtime PM enabled when the PCI devices > > are unbound. But the runtime PM callbacks will do nothing if the PCI > > devices are unbound. This way, we can put the PCI devices into > > SUSPENDED state without put the PCI devices into D3 state. > > > > Known issue: after some changing, pci_dev->driver is used to indicate > > whether the PCI devices are bound and whether the runtime PM callbacks > > should do nothing. Maybe it is better to use a dedicated flag such as > > .skip_rtpm_callbacks. That may improve code readability. > > I think it's okay like this, especially if you add a comment in > pci_runtime_suspend, pci_runtime_resume, and pci_runtime_idle > explaining that when pci_dev->driver isn't set, the device should > always remain in D0 regardless of the runtime status. Yes, I agree with Alan. Please add comments as Alan's suggesting and it should be fine. Thanks, Rafael
On Mon, 2012-11-19 at 23:00 +0100, Rafael J. Wysocki wrote: > On Monday, November 19, 2012 11:31:01 AM Alan Stern wrote: > > On Mon, 19 Nov 2012, Huang Ying wrote: > > > > > For unbound PCI devices, what we need is: > > > > > > - Always in D0 state, because some devices does not work again after > > > being put into D3 by the PCI bus. > > > > > > - In SUSPENDED state if allowed, so that the parent devices can still > > > be put into low power state. > > > > > > To satisfy these requirement, the runtime PM for the unbound PCI > > > devices are disabled and set to SUSPENDED state. One issue of this > > > solution is that the PCI devices will be put into SUSPENDED state even > > > if the SUSPENDED state is forbidden via the sysfs interface > > > (.../power/control) of the device. This is not an issue for most > > > devices, because most PCI devices are not used at all if unbounded. > > > But there are exceptions. For example, unbound VGA card can be used > > > for display, but suspend its parents make it stop working. > > > > > > To fix the issue, we keep the runtime PM enabled when the PCI devices > > > are unbound. But the runtime PM callbacks will do nothing if the PCI > > > devices are unbound. This way, we can put the PCI devices into > > > SUSPENDED state without put the PCI devices into D3 state. > > > > > > Known issue: after some changing, pci_dev->driver is used to indicate > > > whether the PCI devices are bound and whether the runtime PM callbacks > > > should do nothing. Maybe it is better to use a dedicated flag such as > > > .skip_rtpm_callbacks. That may improve code readability. > > > > I think it's okay like this, especially if you add a comment in > > pci_runtime_suspend, pci_runtime_resume, and pci_runtime_idle > > explaining that when pci_dev->driver isn't set, the device should > > always remain in D0 regardless of the runtime status. > > Yes, I agree with Alan. Please add comments as Alan's suggesting and it > should be fine. Sure. Will do that. Best Regards, Huang Ying -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
--- a/drivers/pci/pci.c +++ b/drivers/pci/pci.c @@ -1900,6 +1900,8 @@ void pci_pm_init(struct pci_dev *dev) u16 pmc; pm_runtime_forbid(&dev->dev); + pm_runtime_set_active(&dev->dev); + pm_runtime_enable(&dev->dev); device_enable_async_suspend(&dev->dev); dev->wakeup_prepared = false; --- a/drivers/pci/pci-driver.c +++ b/drivers/pci/pci-driver.c @@ -256,31 +256,26 @@ struct drv_dev_and_id { static long local_pci_probe(void *_ddi) { struct drv_dev_and_id *ddi = _ddi; - struct device *dev = &ddi->dev->dev; - struct device *parent = dev->parent; + struct pci_dev *pci_dev = ddi->dev; + struct pci_driver *pci_drv = ddi->drv; + struct device *dev = &pci_dev->dev; int rc; - /* The parent bridge must be in active state when probing */ - if (parent) - pm_runtime_get_sync(parent); - /* Unbound PCI devices are always set to disabled and suspended. - * During probe, the device is set to enabled and active and the - * usage count is incremented. If the driver supports runtime PM, - * it should call pm_runtime_put_noidle() in its probe routine and - * pm_runtime_get_noresume() in its remove routine. - */ - pm_runtime_get_noresume(dev); - pm_runtime_set_active(dev); - pm_runtime_enable(dev); - - rc = ddi->drv->probe(ddi->dev, ddi->id); + /* + * Unbound PCI devices are always set to suspended and put in + * D0. During probe, the device is set to active and the + * usage count is incremented. If the driver supports runtime + * PM, it should call pm_runtime_put_noidle() in its probe + * routine and pm_runtime_get_noresume() in its remove + * routine. + */ + pm_runtime_get_sync(dev); + pci_dev->driver = pci_drv; + rc = pci_drv->probe(pci_dev, ddi->id); if (rc) { - pm_runtime_disable(dev); - pm_runtime_set_suspended(dev); - pm_runtime_put_noidle(dev); + pci_dev->driver = NULL; + pm_runtime_put_sync(dev); } - if (parent) - pm_runtime_put(parent); return rc; } @@ -330,10 +325,8 @@ __pci_device_probe(struct pci_driver *dr id = pci_match_device(drv, pci_dev); if (id) error = pci_call_probe(drv, pci_dev, id); - if (error >= 0) { - pci_dev->driver = drv; + if (error >= 0) error = 0; - } } return error; } @@ -369,9 +362,7 @@ static int pci_device_remove(struct devi } /* Undo the runtime PM settings in local_pci_probe() */ - pm_runtime_disable(dev); - pm_runtime_set_suspended(dev); - pm_runtime_put_noidle(dev); + pm_runtime_put_sync(dev); /* * If the device is still on, set the power state as "unknown", @@ -994,6 +985,9 @@ static int pci_pm_runtime_suspend(struct pci_power_t prev = pci_dev->current_state; int error; + if (!pci_dev->driver) + return 0; + if (!pm || !pm->runtime_suspend) return -ENOSYS; @@ -1029,6 +1023,9 @@ static int pci_pm_runtime_resume(struct struct pci_dev *pci_dev = to_pci_dev(dev); const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL; + if (!pci_dev->driver) + return 0; + if (!pm || !pm->runtime_resume) return -ENOSYS; @@ -1046,8 +1043,12 @@ static int pci_pm_runtime_resume(struct static int pci_pm_runtime_idle(struct device *dev) { + struct pci_dev *pci_dev = to_pci_dev(dev); const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL; + if (!pci_dev->driver) + goto out; + if (!pm) return -ENOSYS; @@ -1057,8 +1058,8 @@ static int pci_pm_runtime_idle(struct de return ret; } +out: pm_runtime_suspend(dev); - return 0; }
For unbound PCI devices, what we need is: - Always in D0 state, because some devices does not work again after being put into D3 by the PCI bus. - In SUSPENDED state if allowed, so that the parent devices can still be put into low power state. To satisfy these requirement, the runtime PM for the unbound PCI devices are disabled and set to SUSPENDED state. One issue of this solution is that the PCI devices will be put into SUSPENDED state even if the SUSPENDED state is forbidden via the sysfs interface (.../power/control) of the device. This is not an issue for most devices, because most PCI devices are not used at all if unbounded. But there are exceptions. For example, unbound VGA card can be used for display, but suspend its parents make it stop working. To fix the issue, we keep the runtime PM enabled when the PCI devices are unbound. But the runtime PM callbacks will do nothing if the PCI devices are unbound. This way, we can put the PCI devices into SUSPENDED state without put the PCI devices into D3 state. Known issue: after some changing, pci_dev->driver is used to indicate whether the PCI devices are bound and whether the runtime PM callbacks should do nothing. Maybe it is better to use a dedicated flag such as .skip_rtpm_callbacks. That may improve code readability. Signed-off-by: Huang Ying <ying.huang@intel.com> CC: Rafael J. Wysocki <rafael.j.wysocki@intel.com> CC: Alan Stern <stern@rowland.harvard.edu> CC: stable@vger.kernel.org # v3.6+ --- drivers/pci/pci-driver.c | 57 +++++++++++++++++++++++------------------------ drivers/pci/pci.c | 2 + 2 files changed, 31 insertions(+), 28 deletions(-) -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html