| Message ID | 20190129161040.20299-1-piotrs@cadence.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | mtd: nand: Add Cadence NAND controller driver | expand |
Hi Piotr, On Tue, 29 Jan 2019 16:10:40 +0000 Piotr Sroka <piotrs@cadence.com> wrote: > Signed-off-by: Piotr Sroka <piotrs@cadence.com> > --- > .../devicetree/bindings/mtd/cadence-nand.txt | 35 ++++++++++++++++++++++ > 1 file changed, 35 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mtd/cadence-nand.txt > > diff --git a/Documentation/devicetree/bindings/mtd/cadence-nand.txt b/Documentation/devicetree/bindings/mtd/cadence-nand.txt > new file mode 100644 > index 000000000000..82afa34d5652 > --- /dev/null > +++ b/Documentation/devicetree/bindings/mtd/cadence-nand.txt > @@ -0,0 +1,35 @@ > +* Cadence NAND controller > + > +Required properties: > + - compatible : "cdns,hpnfc-nand" "nfc" already means nand flash controller, no need to suffix it with -nand, "cdns,hpnfc" should be enough. > + - reg : Contains two entries, each of which is a tuple consisting of a > + physical address and length. The first entry is the address and > + length of the controller register set. The second entry is the > + address and length of the Slave DMA data port. Please name the register ranges. > + - interrupts : The interrupt number. > + - clocks: phandle of the controller core clock (nf_clk). > + > +Optional properties: > +Driver calculates controller timings base on NAND flash memory timings and > +the following delays in picoseconds. > + - cdns,if-skew : Skew value of the output signals of the NAND Flash interface > + - cdns,nand2-delay : Delay value of one NAND2 gate from which > + the delay element is build > + - cdns,board-delay : Estimated Board delay. The value includes the total > + round trip delay for the signals and is used for deciding on values > + associated with data read capture. The example formula for SDR mode is > + the following: > + board_delay = RE#PAD_delay + PCB trace to device + PCB trace from device > + + DQ PAD delay The unit of those props is not defined, and if possible I'd like to avoid specifying custom timing adjustment values in the DT. Looks like some of these values are SoC specific (depends on the integration of this IP in a SoC) and others are board specific. For SoC specific values, this should be attached to the SoC specific compatible at the driver level. For board-specific values, I'd prefer to have a generic way to describe boards constraints. Please point to the generic bindings to describe NAND chip representation under the NAND controller node. > + > +Example > + > +nand: nand@60000000 { nand_controller: nand-controller@60000000 { > + compatible = "cdns,hpnfc-nand"; > + reg = <0x60000000 0x10000>, <0x80000000 0x10000>; > + clocks = <&nf_clk>; > + cdns,if-skew = <50>; > + cdns,nand2-delay = <37>; > + cdns,board-delay = <4830>; > + interrupts = <2 0>; Add a NAND chip in the example. > +}; Regards, Boris
The 01/29/2019 18:21, Boris Brezillon wrote: >> +Optional properties: >> +Driver calculates controller timings base on NAND flash memory timings and >> +the following delays in picoseconds. >> + - cdns,if-skew : Skew value of the output signals of the NAND Flash interface >> + - cdns,nand2-delay : Delay value of one NAND2 gate from which >> + the delay element is build >> + - cdns,board-delay : Estimated Board delay. The value includes the total >> + round trip delay for the signals and is used for deciding on values >> + associated with data read capture. The example formula for SDR mode is >> + the following: >> + board_delay = RE#PAD_delay + PCB trace to device + PCB trace from device >> + + DQ PAD delay > >The unit of those props is not defined, and if possible I'd like to >avoid specifying custom timing adjustment values in the DT. Looks like >some of these values are SoC specific (depends on the integration of >this IP in a SoC) and others are board specific. For SoC specific >values, this should be attached to the SoC specific compatible at the >driver level. For board-specific values, I'd prefer to have a generic >way to describe boards constraints. Moving SoC specific delays from DTS to the driver data is clear for me. I do not know how to handle a board delay. Could you give me an example how it may be implemented? Where this board related stuff could be placed?
diff --git a/Documentation/devicetree/bindings/mtd/cadence-nand.txt b/Documentation/devicetree/bindings/mtd/cadence-nand.txt new file mode 100644 index 000000000000..82afa34d5652 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/cadence-nand.txt @@ -0,0 +1,35 @@ +* Cadence NAND controller + +Required properties: + - compatible : "cdns,hpnfc-nand" + - reg : Contains two entries, each of which is a tuple consisting of a + physical address and length. The first entry is the address and + length of the controller register set. The second entry is the + address and length of the Slave DMA data port. + - interrupts : The interrupt number. + - clocks: phandle of the controller core clock (nf_clk). + +Optional properties: +Driver calculates controller timings base on NAND flash memory timings and +the following delays in picoseconds. + - cdns,if-skew : Skew value of the output signals of the NAND Flash interface + - cdns,nand2-delay : Delay value of one NAND2 gate from which + the delay element is build + - cdns,board-delay : Estimated Board delay. The value includes the total + round trip delay for the signals and is used for deciding on values + associated with data read capture. The example formula for SDR mode is + the following: + board_delay = RE#PAD_delay + PCB trace to device + PCB trace from device + + DQ PAD delay + +Example + +nand: nand@60000000 { + compatible = "cdns,hpnfc-nand"; + reg = <0x60000000 0x10000>, <0x80000000 0x10000>; + clocks = <&nf_clk>; + cdns,if-skew = <50>; + cdns,nand2-delay = <37>; + cdns,board-delay = <4830>; + interrupts = <2 0>; +};
Signed-off-by: Piotr Sroka <piotrs@cadence.com> --- .../devicetree/bindings/mtd/cadence-nand.txt | 35 ++++++++++++++++++++++ 1 file changed, 35 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/cadence-nand.txt