diff --git a/drivers/mtd/spi-nor/Kconfig b/drivers/mtd/spi-nor/Kconfig
index 6cc9c929ff57..d4f9187100e2 100644
--- a/drivers/mtd/spi-nor/Kconfig
+++ b/drivers/mtd/spi-nor/Kconfig
@@ -7,14 +7,6 @@ menuconfig MTD_SPI_NOR
 
 if MTD_SPI_NOR
 
-config MTD_MT81xx_NOR
-	tristate "Mediatek MT81xx SPI NOR flash controller"
-	depends on HAS_IOMEM
-	help
-	  This enables access to SPI NOR flash, using MT81xx SPI NOR flash
-	  controller. This controller does not support generic SPI BUS, it only
-	  supports SPI NOR Flash.
-
 config MTD_SPI_NOR_USE_4K_SECTORS
 	bool "Use small 4096 B erase sectors"
 	default y
@@ -29,104 +21,6 @@ config MTD_SPI_NOR_USE_4K_SECTORS
 	  Please note that some tools/drivers/filesystems may not work with
 	  4096 B erase size (e.g. UBIFS requires 15 KiB as a minimum).
 
-config SPI_ASPEED_SMC
-	tristate "Aspeed flash controllers in SPI mode"
-	depends on ARCH_ASPEED || COMPILE_TEST
-	depends on HAS_IOMEM && OF
-	help
-	  This enables support for the Firmware Memory controller (FMC)
-	  in the Aspeed AST2500/AST2400 SoCs when attached to SPI NOR chips,
-	  and support for the SPI flash memory controller (SPI) for
-	  the host firmware. The implementation only supports SPI NOR.
-
-config SPI_ATMEL_QUADSPI
-	tristate "Atmel Quad SPI Controller"
-	depends on ARCH_AT91 || (ARM && COMPILE_TEST)
-	depends on OF && HAS_IOMEM
-	help
-	  This enables support for the Quad SPI controller in master mode.
-	  This driver does not support generic SPI. The implementation only
-	  supports SPI NOR.
-
-config SPI_CADENCE_QUADSPI
-	tristate "Cadence Quad SPI controller"
-	depends on OF && (ARM || ARM64 || COMPILE_TEST)
-	help
-	  Enable support for the Cadence Quad SPI Flash controller.
-
-	  Cadence QSPI is a specialized controller for connecting an SPI
-	  Flash over 1/2/4-bit wide bus. Enable this option if you have a
-	  device with a Cadence QSPI controller and want to access the
-	  Flash as an MTD device.
-
-config SPI_FSL_QUADSPI
-	tristate "Freescale Quad SPI controller"
-	depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
-	depends on HAS_IOMEM
-	help
-	  This enables support for the Quad SPI controller in master mode.
-	  This controller does not support generic SPI. It only supports
-	  SPI NOR.
-
-config SPI_HISI_SFC
-	tristate "Hisilicon SPI-NOR Flash Controller(SFC)"
-	depends on ARCH_HISI || COMPILE_TEST
-	depends on HAS_IOMEM
-	help
-	  This enables support for hisilicon SPI-NOR flash controller.
-
-config SPI_NXP_SPIFI
-	tristate "NXP SPI Flash Interface (SPIFI)"
-	depends on OF && (ARCH_LPC18XX || COMPILE_TEST)
-	depends on HAS_IOMEM
-	help
-	  Enable support for the NXP LPC SPI Flash Interface controller.
-
-	  SPIFI is a specialized controller for connecting serial SPI
-	  Flash. Enable this option if you have a device with a SPIFI
-	  controller and want to access the Flash as a mtd device.
-
-config SPI_INTEL_SPI
-	tristate
-
-config SPI_INTEL_SPI_PCI
-	tristate "Intel PCH/PCU SPI flash PCI driver (DANGEROUS)"
-	depends on X86 && PCI
-	select SPI_INTEL_SPI
-	help
-	  This enables PCI support for the Intel PCH/PCU SPI controller in
-	  master mode. This controller is present in modern Intel hardware
-	  and is used to hold BIOS and other persistent settings. Using
-	  this driver it is possible to upgrade BIOS directly from Linux.
-
-	  Say N here unless you know what you are doing. Overwriting the
-	  SPI flash may render the system unbootable.
-
-	  To compile this driver as a module, choose M here: the module
-	  will be called intel-spi-pci.
-
-config SPI_INTEL_SPI_PLATFORM
-	tristate "Intel PCH/PCU SPI flash platform driver (DANGEROUS)"
-	depends on X86
-	select SPI_INTEL_SPI
-	help
-	  This enables platform support for the Intel PCH/PCU SPI
-	  controller in master mode. This controller is present in modern
-	  Intel hardware and is used to hold BIOS and other persistent
-	  settings. Using this driver it is possible to upgrade BIOS
-	  directly from Linux.
-
-	  Say N here unless you know what you are doing. Overwriting the
-	  SPI flash may render the system unbootable.
-
-	  To compile this driver as a module, choose M here: the module
-	  will be called intel-spi-platform.
-
-config SPI_STM32_QUADSPI
-	tristate "STM32 Quad SPI controller"
-	depends on ARCH_STM32 || COMPILE_TEST
-	help
-	  This enables support for the STM32 Quad SPI controller.
-	  We only connect the NOR to this controller.
+source "drivers/mtd/spi-nor/controllers/Kconfig"
 
 endif # MTD_SPI_NOR
diff --git a/drivers/mtd/spi-nor/Makefile b/drivers/mtd/spi-nor/Makefile
index f4c61d282abd..0d6c4967a445 100644
--- a/drivers/mtd/spi-nor/Makefile
+++ b/drivers/mtd/spi-nor/Makefile
@@ -1,13 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
+spi-nor-objs			:= core.o
 obj-$(CONFIG_MTD_SPI_NOR)	+= spi-nor.o
-obj-$(CONFIG_SPI_ASPEED_SMC)	+= aspeed-smc.o
-obj-$(CONFIG_SPI_ATMEL_QUADSPI)	+= atmel-quadspi.o
-obj-$(CONFIG_SPI_CADENCE_QUADSPI)	+= cadence-quadspi.o
-obj-$(CONFIG_SPI_FSL_QUADSPI)	+= fsl-quadspi.o
-obj-$(CONFIG_SPI_HISI_SFC)	+= hisi-sfc.o
-obj-$(CONFIG_MTD_MT81xx_NOR)    += mtk-quadspi.o
-obj-$(CONFIG_SPI_NXP_SPIFI)	+= nxp-spifi.o
-obj-$(CONFIG_SPI_INTEL_SPI)	+= intel-spi.o
-obj-$(CONFIG_SPI_INTEL_SPI_PCI)	+= intel-spi-pci.o
-obj-$(CONFIG_SPI_INTEL_SPI_PLATFORM)	+= intel-spi-platform.o
-obj-$(CONFIG_SPI_STM32_QUADSPI)	+= stm32-quadspi.o
+
+obj-$(CONFIG_MTD_SPI_NOR)	+= controllers/
diff --git a/drivers/mtd/spi-nor/controllers/Kconfig b/drivers/mtd/spi-nor/controllers/Kconfig
new file mode 100644
index 000000000000..6356cbf465a4
--- /dev/null
+++ b/drivers/mtd/spi-nor/controllers/Kconfig
@@ -0,0 +1,107 @@
+config MTD_MT81xx_NOR
+	tristate "Mediatek MT81xx SPI NOR flash controller"
+	depends on HAS_IOMEM
+	help
+	  This enables access to SPI NOR flash, using MT81xx SPI NOR flash
+	  controller. This controller does not support generic SPI BUS, it only
+	  supports SPI NOR Flash.
+
+config SPI_ASPEED_SMC
+	tristate "Aspeed flash controllers in SPI mode"
+	depends on ARCH_ASPEED || COMPILE_TEST
+	depends on HAS_IOMEM && OF
+	help
+	  This enables support for the Firmware Memory controller (FMC)
+	  in the Aspeed AST2500/AST2400 SoCs when attached to SPI NOR chips,
+	  and support for the SPI flash memory controller (SPI) for
+	  the host firmware. The implementation only supports SPI NOR.
+
+config SPI_ATMEL_QUADSPI
+	tristate "Atmel Quad SPI Controller"
+	depends on ARCH_AT91 || (ARM && COMPILE_TEST)
+	depends on OF && HAS_IOMEM
+	help
+	  This enables support for the Quad SPI controller in master mode.
+	  This driver does not support generic SPI. The implementation only
+	  supports SPI NOR.
+
+config SPI_CADENCE_QUADSPI
+	tristate "Cadence Quad SPI controller"
+	depends on OF && (ARM || ARM64 || COMPILE_TEST)
+	help
+	  Enable support for the Cadence Quad SPI Flash controller.
+
+	  Cadence QSPI is a specialized controller for connecting an SPI
+	  Flash over 1/2/4-bit wide bus. Enable this option if you have a
+	  device with a Cadence QSPI controller and want to access the
+	  Flash as an MTD device.
+
+config SPI_FSL_QUADSPI
+	tristate "Freescale Quad SPI controller"
+	depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
+	depends on HAS_IOMEM
+	help
+	  This enables support for the Quad SPI controller in master mode.
+	  This controller does not support generic SPI. It only supports
+	  SPI NOR.
+
+config SPI_HISI_SFC
+	tristate "Hisilicon SPI-NOR Flash Controller(SFC)"
+	depends on ARCH_HISI || COMPILE_TEST
+	depends on HAS_IOMEM
+	help
+	  This enables support for hisilicon SPI-NOR flash controller.
+
+config SPI_NXP_SPIFI
+	tristate "NXP SPI Flash Interface (SPIFI)"
+	depends on OF && (ARCH_LPC18XX || COMPILE_TEST)
+	depends on HAS_IOMEM
+	help
+	  Enable support for the NXP LPC SPI Flash Interface controller.
+
+	  SPIFI is a specialized controller for connecting serial SPI
+	  Flash. Enable this option if you have a device with a SPIFI
+	  controller and want to access the Flash as a mtd device.
+
+config SPI_INTEL_SPI
+	tristate
+
+config SPI_INTEL_SPI_PCI
+	tristate "Intel PCH/PCU SPI flash PCI driver (DANGEROUS)"
+	depends on X86 && PCI
+	select SPI_INTEL_SPI
+	help
+	  This enables PCI support for the Intel PCH/PCU SPI controller in
+	  master mode. This controller is present in modern Intel hardware
+	  and is used to hold BIOS and other persistent settings. Using
+	  this driver it is possible to upgrade BIOS directly from Linux.
+
+	  Say N here unless you know what you are doing. Overwriting the
+	  SPI flash may render the system unbootable.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called intel-spi-pci.
+
+config SPI_INTEL_SPI_PLATFORM
+	tristate "Intel PCH/PCU SPI flash platform driver (DANGEROUS)"
+	depends on X86
+	select SPI_INTEL_SPI
+	help
+	  This enables platform support for the Intel PCH/PCU SPI
+	  controller in master mode. This controller is present in modern
+	  Intel hardware and is used to hold BIOS and other persistent
+	  settings. Using this driver it is possible to upgrade BIOS
+	  directly from Linux.
+
+	  Say N here unless you know what you are doing. Overwriting the
+	  SPI flash may render the system unbootable.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called intel-spi-platform.
+
+config SPI_STM32_QUADSPI
+	tristate "STM32 Quad SPI controller"
+	depends on ARCH_STM32 || COMPILE_TEST
+	help
+	  This enables support for the STM32 Quad SPI controller.
+	  We only connect the NOR to this controller.
diff --git a/drivers/mtd/spi-nor/controllers/Makefile b/drivers/mtd/spi-nor/controllers/Makefile
new file mode 100644
index 000000000000..0cb3384a32ac
--- /dev/null
+++ b/drivers/mtd/spi-nor/controllers/Makefile
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_SPI_ASPEED_SMC)	+= aspeed-smc.o
+obj-$(CONFIG_SPI_ATMEL_QUADSPI)	+= atmel-quadspi.o
+obj-$(CONFIG_SPI_CADENCE_QUADSPI)	+= cadence-quadspi.o
+obj-$(CONFIG_SPI_FSL_QUADSPI)	+= fsl-quadspi.o
+obj-$(CONFIG_SPI_HISI_SFC)	+= hisi-sfc.o
+obj-$(CONFIG_MTD_MT81xx_NOR)    += mtk-quadspi.o
+obj-$(CONFIG_SPI_NXP_SPIFI)	+= nxp-spifi.o
+obj-$(CONFIG_SPI_INTEL_SPI)	+= intel-spi.o
+obj-$(CONFIG_SPI_INTEL_SPI_PCI)	+= intel-spi-pci.o
+obj-$(CONFIG_SPI_INTEL_SPI_PLATFORM)	+= intel-spi-platform.o
+obj-$(CONFIG_SPI_STM32_QUADSPI)	+= stm32-quadspi.o
diff --git a/drivers/mtd/spi-nor/aspeed-smc.c b/drivers/mtd/spi-nor/controllers/aspeed-smc.c
similarity index 100%
rename from drivers/mtd/spi-nor/aspeed-smc.c
rename to drivers/mtd/spi-nor/controllers/aspeed-smc.c
diff --git a/drivers/mtd/spi-nor/atmel-quadspi.c b/drivers/mtd/spi-nor/controllers/atmel-quadspi.c
similarity index 100%
rename from drivers/mtd/spi-nor/atmel-quadspi.c
rename to drivers/mtd/spi-nor/controllers/atmel-quadspi.c
diff --git a/drivers/mtd/spi-nor/cadence-quadspi.c b/drivers/mtd/spi-nor/controllers/cadence-quadspi.c
similarity index 100%
rename from drivers/mtd/spi-nor/cadence-quadspi.c
rename to drivers/mtd/spi-nor/controllers/cadence-quadspi.c
diff --git a/drivers/mtd/spi-nor/fsl-quadspi.c b/drivers/mtd/spi-nor/controllers/fsl-quadspi.c
similarity index 100%
rename from drivers/mtd/spi-nor/fsl-quadspi.c
rename to drivers/mtd/spi-nor/controllers/fsl-quadspi.c
diff --git a/drivers/mtd/spi-nor/hisi-sfc.c b/drivers/mtd/spi-nor/controllers/hisi-sfc.c
similarity index 100%
rename from drivers/mtd/spi-nor/hisi-sfc.c
rename to drivers/mtd/spi-nor/controllers/hisi-sfc.c
diff --git a/drivers/mtd/spi-nor/intel-spi-pci.c b/drivers/mtd/spi-nor/controllers/intel-spi-pci.c
similarity index 100%
rename from drivers/mtd/spi-nor/intel-spi-pci.c
rename to drivers/mtd/spi-nor/controllers/intel-spi-pci.c
diff --git a/drivers/mtd/spi-nor/intel-spi-platform.c b/drivers/mtd/spi-nor/controllers/intel-spi-platform.c
similarity index 100%
rename from drivers/mtd/spi-nor/intel-spi-platform.c
rename to drivers/mtd/spi-nor/controllers/intel-spi-platform.c
diff --git a/drivers/mtd/spi-nor/intel-spi.c b/drivers/mtd/spi-nor/controllers/intel-spi.c
similarity index 100%
rename from drivers/mtd/spi-nor/intel-spi.c
rename to drivers/mtd/spi-nor/controllers/intel-spi.c
diff --git a/drivers/mtd/spi-nor/intel-spi.h b/drivers/mtd/spi-nor/controllers/intel-spi.h
similarity index 100%
rename from drivers/mtd/spi-nor/intel-spi.h
rename to drivers/mtd/spi-nor/controllers/intel-spi.h
diff --git a/drivers/mtd/spi-nor/mtk-quadspi.c b/drivers/mtd/spi-nor/controllers/mtk-quadspi.c
similarity index 100%
rename from drivers/mtd/spi-nor/mtk-quadspi.c
rename to drivers/mtd/spi-nor/controllers/mtk-quadspi.c
diff --git a/drivers/mtd/spi-nor/nxp-spifi.c b/drivers/mtd/spi-nor/controllers/nxp-spifi.c
similarity index 100%
rename from drivers/mtd/spi-nor/nxp-spifi.c
rename to drivers/mtd/spi-nor/controllers/nxp-spifi.c
diff --git a/drivers/mtd/spi-nor/stm32-quadspi.c b/drivers/mtd/spi-nor/controllers/stm32-quadspi.c
similarity index 100%
rename from drivers/mtd/spi-nor/stm32-quadspi.c
rename to drivers/mtd/spi-nor/controllers/stm32-quadspi.c
diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/core.c
similarity index 91%
rename from drivers/mtd/spi-nor/spi-nor.c
rename to drivers/mtd/spi-nor/core.c
index 34d3d632e53b..f8b7c8fbe960 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -22,6 +22,8 @@
 #include <linux/spi/flash.h>
 #include <linux/mtd/spi-nor.h>
 
+#include "internals.h"
+
 /* Define max times to check status register before we give up. */
 
 /*
@@ -36,267 +38,8 @@
  */
 #define CHIP_ERASE_2MB_READY_WAIT_JIFFIES	(40UL * HZ)
 
-#define SPI_NOR_MAX_ID_LEN	6
 #define SPI_NOR_MAX_ADDR_WIDTH	4
 
-struct spi_nor_read_command {
-	u8			num_mode_clocks;
-	u8			num_wait_states;
-	u8			opcode;
-	enum spi_nor_protocol	proto;
-};
-
-struct spi_nor_pp_command {
-	u8			opcode;
-	enum spi_nor_protocol	proto;
-};
-
-enum spi_nor_read_command_index {
-	SNOR_CMD_READ,
-	SNOR_CMD_READ_FAST,
-	SNOR_CMD_READ_1_1_1_DTR,
-
-	/* Dual SPI */
-	SNOR_CMD_READ_1_1_2,
-	SNOR_CMD_READ_1_2_2,
-	SNOR_CMD_READ_2_2_2,
-	SNOR_CMD_READ_1_2_2_DTR,
-
-	/* Quad SPI */
-	SNOR_CMD_READ_1_1_4,
-	SNOR_CMD_READ_1_4_4,
-	SNOR_CMD_READ_4_4_4,
-	SNOR_CMD_READ_1_4_4_DTR,
-
-	/* Octo SPI */
-	SNOR_CMD_READ_1_1_8,
-	SNOR_CMD_READ_1_8_8,
-	SNOR_CMD_READ_8_8_8,
-	SNOR_CMD_READ_1_8_8_DTR,
-
-	SNOR_CMD_READ_MAX
-};
-
-enum spi_nor_pp_command_index {
-	SNOR_CMD_PP,
-
-	/* Quad SPI */
-	SNOR_CMD_PP_1_1_4,
-	SNOR_CMD_PP_1_4_4,
-	SNOR_CMD_PP_4_4_4,
-
-	/* Octo SPI */
-	SNOR_CMD_PP_1_1_8,
-	SNOR_CMD_PP_1_8_8,
-	SNOR_CMD_PP_8_8_8,
-
-	SNOR_CMD_PP_MAX
-};
-
-struct spi_nor_flash_parameter {
-	u64				size;
-	u32				page_size;
-
-	struct spi_nor_hwcaps		hwcaps;
-	struct spi_nor_read_command	reads[SNOR_CMD_READ_MAX];
-	struct spi_nor_pp_command	page_programs[SNOR_CMD_PP_MAX];
-
-	int (*quad_enable)(struct spi_nor *nor);
-};
-
-struct sfdp_parameter_header {
-	u8		id_lsb;
-	u8		minor;
-	u8		major;
-	u8		length; /* in double words */
-	u8		parameter_table_pointer[3]; /* byte address */
-	u8		id_msb;
-};
-
-#define SFDP_PARAM_HEADER_ID(p)	(((p)->id_msb << 8) | (p)->id_lsb)
-#define SFDP_PARAM_HEADER_PTP(p) \
-	(((p)->parameter_table_pointer[2] << 16) | \
-	 ((p)->parameter_table_pointer[1] <<  8) | \
-	 ((p)->parameter_table_pointer[0] <<  0))
-
-#define SFDP_BFPT_ID		0xff00	/* Basic Flash Parameter Table */
-#define SFDP_SECTOR_MAP_ID	0xff81	/* Sector Map Table */
-
-#define SFDP_SIGNATURE		0x50444653U
-#define SFDP_JESD216_MAJOR	1
-#define SFDP_JESD216_MINOR	0
-#define SFDP_JESD216A_MINOR	5
-#define SFDP_JESD216B_MINOR	6
-
-struct sfdp_header {
-	u32		signature; /* Ox50444653U <=> "SFDP" */
-	u8		minor;
-	u8		major;
-	u8		nph; /* 0-base number of parameter headers */
-	u8		unused;
-
-	/* Basic Flash Parameter Table. */
-	struct sfdp_parameter_header	bfpt_header;
-};
-
-/* Basic Flash Parameter Table */
-
-/*
- * JESD216 rev B defines a Basic Flash Parameter Table of 16 DWORDs.
- * They are indexed from 1 but C arrays are indexed from 0.
- */
-#define BFPT_DWORD(i)		((i) - 1)
-#define BFPT_DWORD_MAX		16
-
-/* The first version of JESB216 defined only 9 DWORDs. */
-#define BFPT_DWORD_MAX_JESD216			9
-
-/* 1st DWORD. */
-#define BFPT_DWORD1_FAST_READ_1_1_2		BIT(16)
-#define BFPT_DWORD1_ADDRESS_BYTES_MASK		GENMASK(18, 17)
-#define BFPT_DWORD1_ADDRESS_BYTES_3_ONLY	(0x0UL << 17)
-#define BFPT_DWORD1_ADDRESS_BYTES_3_OR_4	(0x1UL << 17)
-#define BFPT_DWORD1_ADDRESS_BYTES_4_ONLY	(0x2UL << 17)
-#define BFPT_DWORD1_DTR				BIT(19)
-#define BFPT_DWORD1_FAST_READ_1_2_2		BIT(20)
-#define BFPT_DWORD1_FAST_READ_1_4_4		BIT(21)
-#define BFPT_DWORD1_FAST_READ_1_1_4		BIT(22)
-
-/* 5th DWORD. */
-#define BFPT_DWORD5_FAST_READ_2_2_2		BIT(0)
-#define BFPT_DWORD5_FAST_READ_4_4_4		BIT(4)
-
-/* 11th DWORD. */
-#define BFPT_DWORD11_PAGE_SIZE_SHIFT		4
-#define BFPT_DWORD11_PAGE_SIZE_MASK		GENMASK(7, 4)
-
-/* 15th DWORD. */
-
-/*
- * (from JESD216 rev B)
- * Quad Enable Requirements (QER):
- * - 000b: Device does not have a QE bit. Device detects 1-1-4 and 1-4-4
- *         reads based on instruction. DQ3/HOLD# functions are hold during
- *         instruction phase.
- * - 001b: QE is bit 1 of status register 2. It is set via Write Status with
- *         two data bytes where bit 1 of the second byte is one.
- *         [...]
- *         Writing only one byte to the status register has the side-effect of
- *         clearing status register 2, including the QE bit. The 100b code is
- *         used if writing one byte to the status register does not modify
- *         status register 2.
- * - 010b: QE is bit 6 of status register 1. It is set via Write Status with
- *         one data byte where bit 6 is one.
- *         [...]
- * - 011b: QE is bit 7 of status register 2. It is set via Write status
- *         register 2 instruction 3Eh with one data byte where bit 7 is one.
- *         [...]
- *         The status register 2 is read using instruction 3Fh.
- * - 100b: QE is bit 1 of status register 2. It is set via Write Status with
- *         two data bytes where bit 1 of the second byte is one.
- *         [...]
- *         In contrast to the 001b code, writing one byte to the status
- *         register does not modify status register 2.
- * - 101b: QE is bit 1 of status register 2. Status register 1 is read using
- *         Read Status instruction 05h. Status register2 is read using
- *         instruction 35h. QE is set via Writ Status instruction 01h with
- *         two data bytes where bit 1 of the second byte is one.
- *         [...]
- */
-#define BFPT_DWORD15_QER_MASK			GENMASK(22, 20)
-#define BFPT_DWORD15_QER_NONE			(0x0UL << 20) /* Micron */
-#define BFPT_DWORD15_QER_SR2_BIT1_BUGGY		(0x1UL << 20)
-#define BFPT_DWORD15_QER_SR1_BIT6		(0x2UL << 20) /* Macronix */
-#define BFPT_DWORD15_QER_SR2_BIT7		(0x3UL << 20)
-#define BFPT_DWORD15_QER_SR2_BIT1_NO_RD		(0x4UL << 20)
-#define BFPT_DWORD15_QER_SR2_BIT1		(0x5UL << 20) /* Spansion */
-
-struct sfdp_bfpt {
-	u32	dwords[BFPT_DWORD_MAX];
-};
-
-/**
- * struct spi_nor_fixups - SPI NOR fixup hooks
- * @post_bfpt: called after the BFPT table has been parsed
- * @post_sfdp: called after SFDP has been parsed (is also called for SPI NORs
- *	       that do not support RDSFDP). Typically used to tweak various
- *	       parameters that could not be extracted by other means (i.e.
- *	       when information provided by the SFDP/flash_info tables are
- *	       incomplete or wrong).
- *
- * Those hooks can be used to tweak the SPI NOR configuration when the SFDP
- * table is broken or not available.
- */
-struct spi_nor_fixups {
-	int (*post_bfpt)(struct spi_nor *nor,
-			 const struct sfdp_parameter_header *bfpt_header,
-			 const struct sfdp_bfpt *bfpt,
-			 struct spi_nor_flash_parameter *params);
-	int (*post_sfdp)(struct spi_nor *nor,
-			 struct spi_nor_flash_parameter *params);
-};
-
-struct flash_info {
-	char		*name;
-
-	/*
-	 * This array stores the ID bytes.
-	 * The first three bytes are the JEDIC ID.
-	 * JEDEC ID zero means "no ID" (mostly older chips).
-	 */
-	u8		id[SPI_NOR_MAX_ID_LEN];
-	u8		id_len;
-
-	/* The size listed here is what works with SPINOR_OP_SE, which isn't
-	 * necessarily called a "sector" by the vendor.
-	 */
-	unsigned	sector_size;
-	u16		n_sectors;
-
-	u16		page_size;
-	u16		addr_width;
-
-	u16		flags;
-#define SECT_4K			BIT(0)	/* SPINOR_OP_BE_4K works uniformly */
-#define SPI_NOR_NO_ERASE	BIT(1)	/* No erase command needed */
-#define SST_WRITE		BIT(2)	/* use SST byte programming */
-#define SPI_NOR_NO_FR		BIT(3)	/* Can't do fastread */
-#define SECT_4K_PMC		BIT(4)	/* SPINOR_OP_BE_4K_PMC works uniformly */
-#define SPI_NOR_DUAL_READ	BIT(5)	/* Flash supports Dual Read */
-#define SPI_NOR_QUAD_READ	BIT(6)	/* Flash supports Quad Read */
-#define USE_FSR			BIT(7)	/* use flag status register */
-#define SPI_NOR_HAS_LOCK	BIT(8)	/* Flash supports lock/unlock via SR */
-#define SPI_NOR_HAS_TB		BIT(9)	/*
-					 * Flash SR has Top/Bottom (TB) protect
-					 * bit. Must be used with
-					 * SPI_NOR_HAS_LOCK.
-					 */
-#define SPI_NOR_XSR_RDY		BIT(10)	/*
-					 * S3AN flashes have specific opcode to
-					 * read the status register.
-					 * Flags SPI_NOR_XSR_RDY and SPI_S3AN
-					 * use the same bit as one implies the
-					 * other, but we will get rid of
-					 * SPI_S3AN soon.
-					 */
-#define	SPI_S3AN		BIT(10)	/*
-					 * Xilinx Spartan 3AN In-System Flash
-					 * (MFR cannot be used for probing
-					 * because it has the same value as
-					 * ATMEL flashes)
-					 */
-#define SPI_NOR_4B_OPCODES	BIT(11)	/*
-					 * Use dedicated 4byte address op codes
-					 * to support memory size above 128Mib.
-					 */
-#define NO_CHIP_ERASE		BIT(12) /* Chip does not support chip erase */
-#define SPI_NOR_SKIP_SFDP	BIT(13)	/* Skip parsing of SFDP tables */
-#define USE_CLSR		BIT(14)	/* use CLSR command */
-
-	/* Part specific fixup hooks. */
-	const struct spi_nor_fixups *fixups;
-};
-
 #define JEDEC_MFR(info)	((info)->id[0])
 
 /*
@@ -1617,56 +1360,6 @@ static int sr2_bit7_quad_enable(struct spi_nor *nor)
 	return 0;
 }
 
-/* Used when the "_ext_id" is two bytes at most */
-#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags)	\
-		.id = {							\
-			((_jedec_id) >> 16) & 0xff,			\
-			((_jedec_id) >> 8) & 0xff,			\
-			(_jedec_id) & 0xff,				\
-			((_ext_id) >> 8) & 0xff,			\
-			(_ext_id) & 0xff,				\
-			},						\
-		.id_len = (!(_jedec_id) ? 0 : (3 + ((_ext_id) ? 2 : 0))),	\
-		.sector_size = (_sector_size),				\
-		.n_sectors = (_n_sectors),				\
-		.page_size = 256,					\
-		.flags = (_flags),
-
-#define INFO6(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags)	\
-		.id = {							\
-			((_jedec_id) >> 16) & 0xff,			\
-			((_jedec_id) >> 8) & 0xff,			\
-			(_jedec_id) & 0xff,				\
-			((_ext_id) >> 16) & 0xff,			\
-			((_ext_id) >> 8) & 0xff,			\
-			(_ext_id) & 0xff,				\
-			},						\
-		.id_len = 6,						\
-		.sector_size = (_sector_size),				\
-		.n_sectors = (_n_sectors),				\
-		.page_size = 256,					\
-		.flags = (_flags),
-
-#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_width, _flags)	\
-		.sector_size = (_sector_size),				\
-		.n_sectors = (_n_sectors),				\
-		.page_size = (_page_size),				\
-		.addr_width = (_addr_width),				\
-		.flags = (_flags),
-
-#define S3AN_INFO(_jedec_id, _n_sectors, _page_size)			\
-		.id = {							\
-			((_jedec_id) >> 16) & 0xff,			\
-			((_jedec_id) >> 8) & 0xff,			\
-			(_jedec_id) & 0xff				\
-			},						\
-		.id_len = 3,						\
-		.sector_size = (8*_page_size),				\
-		.n_sectors = (_n_sectors),				\
-		.page_size = _page_size,				\
-		.addr_width = 3,					\
-		.flags = SPI_NOR_NO_FR | SPI_S3AN,
-
 static int gd25q256_post_sfdp_fixups(struct spi_nor *nor,
 				     struct spi_nor_flash_parameter *params)
 {
diff --git a/drivers/mtd/spi-nor/internals.h b/drivers/mtd/spi-nor/internals.h
new file mode 100644
index 000000000000..cc06fed99f49
--- /dev/null
+++ b/drivers/mtd/spi-nor/internals.h
@@ -0,0 +1,321 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005, Intec Automation Inc.
+ * Copyright (C) 2014, Freescale Semiconductor, Inc.
+ */
+
+#ifndef __LINUX_MTD_SPI_NOR_INTERNALS_H
+#define __LINUX_MTD_SPI_NOR_INTERNALS_H
+
+#define SPI_NOR_MAX_ID_LEN      6
+
+struct spi_nor_read_command {
+	u8			num_mode_clocks;
+	u8			num_wait_states;
+	u8			opcode;
+	enum spi_nor_protocol	proto;
+};
+
+struct spi_nor_pp_command {
+	u8			opcode;
+	enum spi_nor_protocol	proto;
+};
+
+enum spi_nor_read_command_index {
+	SNOR_CMD_READ,
+	SNOR_CMD_READ_FAST,
+	SNOR_CMD_READ_1_1_1_DTR,
+
+	/* Dual SPI */
+	SNOR_CMD_READ_1_1_2,
+	SNOR_CMD_READ_1_2_2,
+	SNOR_CMD_READ_2_2_2,
+	SNOR_CMD_READ_1_2_2_DTR,
+
+	/* Quad SPI */
+	SNOR_CMD_READ_1_1_4,
+	SNOR_CMD_READ_1_4_4,
+	SNOR_CMD_READ_4_4_4,
+	SNOR_CMD_READ_1_4_4_DTR,
+
+	/* Octo SPI */
+	SNOR_CMD_READ_1_1_8,
+	SNOR_CMD_READ_1_8_8,
+	SNOR_CMD_READ_8_8_8,
+	SNOR_CMD_READ_1_8_8_DTR,
+
+	SNOR_CMD_READ_MAX
+};
+
+enum spi_nor_pp_command_index {
+	SNOR_CMD_PP,
+
+	/* Quad SPI */
+	SNOR_CMD_PP_1_1_4,
+	SNOR_CMD_PP_1_4_4,
+	SNOR_CMD_PP_4_4_4,
+
+	/* Octo SPI */
+	SNOR_CMD_PP_1_1_8,
+	SNOR_CMD_PP_1_8_8,
+	SNOR_CMD_PP_8_8_8,
+
+	SNOR_CMD_PP_MAX
+};
+
+struct spi_nor_flash_parameter {
+	u64				size;
+	u32				page_size;
+
+	struct spi_nor_hwcaps		hwcaps;
+	struct spi_nor_read_command	reads[SNOR_CMD_READ_MAX];
+	struct spi_nor_pp_command	page_programs[SNOR_CMD_PP_MAX];
+
+	int (*quad_enable)(struct spi_nor *nor);
+};
+
+struct sfdp_parameter_header {
+	u8		id_lsb;
+	u8		minor;
+	u8		major;
+	u8		length; /* in double words */
+	u8		parameter_table_pointer[3]; /* byte address */
+	u8		id_msb;
+};
+
+#define SFDP_PARAM_HEADER_ID(p)	(((p)->id_msb << 8) | (p)->id_lsb)
+#define SFDP_PARAM_HEADER_PTP(p) \
+	(((p)->parameter_table_pointer[2] << 16) | \
+	 ((p)->parameter_table_pointer[1] <<  8) | \
+	 ((p)->parameter_table_pointer[0] <<  0))
+
+#define SFDP_BFPT_ID		0xff00	/* Basic Flash Parameter Table */
+#define SFDP_SECTOR_MAP_ID	0xff81	/* Sector Map Table */
+
+#define SFDP_SIGNATURE		0x50444653U
+#define SFDP_JESD216_MAJOR	1
+#define SFDP_JESD216_MINOR	0
+#define SFDP_JESD216A_MINOR	5
+#define SFDP_JESD216B_MINOR	6
+
+struct sfdp_header {
+	u32		signature; /* Ox50444653U <=> "SFDP" */
+	u8		minor;
+	u8		major;
+	u8		nph; /* 0-base number of parameter headers */
+	u8		unused;
+
+	/* Basic Flash Parameter Table. */
+	struct sfdp_parameter_header	bfpt_header;
+};
+
+/* Basic Flash Parameter Table */
+
+/*
+ * JESD216 rev B defines a Basic Flash Parameter Table of 16 DWORDs.
+ * They are indexed from 1 but C arrays are indexed from 0.
+ */
+#define BFPT_DWORD(i)		((i) - 1)
+#define BFPT_DWORD_MAX		16
+
+/* The first version of JESB216 defined only 9 DWORDs. */
+#define BFPT_DWORD_MAX_JESD216			9
+
+/* 1st DWORD. */
+#define BFPT_DWORD1_FAST_READ_1_1_2		BIT(16)
+#define BFPT_DWORD1_ADDRESS_BYTES_MASK		GENMASK(18, 17)
+
+#define BFPT_DWORD1_ADDRESS_BYTES_3_ONLY	(0x0UL << 17)
+#define BFPT_DWORD1_ADDRESS_BYTES_3_OR_4	(0x1UL << 17)
+#define BFPT_DWORD1_ADDRESS_BYTES_4_ONLY	(0x2UL << 17)
+#define BFPT_DWORD1_DTR				BIT(19)
+#define BFPT_DWORD1_FAST_READ_1_2_2		BIT(20)
+#define BFPT_DWORD1_FAST_READ_1_4_4		BIT(21)
+#define BFPT_DWORD1_FAST_READ_1_1_4		BIT(22)
+
+/* 5th DWORD. */
+#define BFPT_DWORD5_FAST_READ_2_2_2		BIT(0)
+#define BFPT_DWORD5_FAST_READ_4_4_4		BIT(4)
+
+/* 11th DWORD. */
+#define BFPT_DWORD11_PAGE_SIZE_SHIFT		4
+#define BFPT_DWORD11_PAGE_SIZE_MASK		GENMASK(7, 4)
+
+/* 15th DWORD. */
+
+/*
+ * (from JESD216 rev B)
+ * Quad Enable Requirements (QER):
+ * - 000b: Device does not have a QE bit. Device detects 1-1-4 and 1-4-4
+ *         reads based on instruction. DQ3/HOLD# functions are hold during
+ *         instruction phase.
+ * - 001b: QE is bit 1 of status register 2. It is set via Write Status with
+ *         two data bytes where bit 1 of the second byte is one.
+ *         [...]
+ *         Writing only one byte to the status register has the side-effect of
+ *         clearing status register 2, including the QE bit. The 100b code is
+ *         used if writing one byte to the status register does not modify
+ *         status register 2.
+ * - 010b: QE is bit 6 of status register 1. It is set via Write Status with
+ *         one data byte where bit 6 is one.
+ *         [...]
+ * - 011b: QE is bit 7 of status register 2. It is set via Write status
+ *         register 2 instruction 3Eh with one data byte where bit 7 is one.
+ *         [...]
+ *         The status register 2 is read using instruction 3Fh.
+ * - 100b: QE is bit 1 of status register 2. It is set via Write Status with
+ *         two data bytes where bit 1 of the second byte is one.
+ *         [...]
+ *         In contrast to the 001b code, writing one byte to the status
+ *         register does not modify status register 2.
+ * - 101b: QE is bit 1 of status register 2. Status register 1 is read using
+ *         Read Status instruction 05h. Status register2 is read using
+ *         instruction 35h. QE is set via Writ Status instruction 01h with
+ *         two data bytes where bit 1 of the second byte is one.
+ *         [...]
+ */
+#define BFPT_DWORD15_QER_MASK			GENMASK(22, 20)
+#define BFPT_DWORD15_QER_NONE			(0x0UL << 20) /* Micron */
+#define BFPT_DWORD15_QER_SR2_BIT1_BUGGY		(0x1UL << 20)
+#define BFPT_DWORD15_QER_SR1_BIT6		(0x2UL << 20) /* Macronix */
+#define BFPT_DWORD15_QER_SR2_BIT7		(0x3UL << 20)
+#define BFPT_DWORD15_QER_SR2_BIT1_NO_RD		(0x4UL << 20)
+#define BFPT_DWORD15_QER_SR2_BIT1		(0x5UL << 20) /* Spansion */
+
+struct sfdp_bfpt {
+	u32	dwords[BFPT_DWORD_MAX];
+};
+
+/**
+ * struct spi_nor_fixups - SPI NOR fixup hooks
+ * @post_bfpt: called after the BFPT table has been parsed
+ * @post_sfdp: called after SFDP has been parsed (is also called for SPI NORs
+ *	       that do not support RDSFDP). Typically used to tweak various
+ *	       parameters that could not be extracted by other means (i.e.
+ *	       when information provided by the SFDP/flash_info tables are
+ *	       incomplete or wrong).
+ *
+ * Those hooks can be used to tweak the SPI NOR configuration when the SFDP
+ * table is broken or not available.
+ */
+struct spi_nor_fixups {
+	int (*post_bfpt)(struct spi_nor *nor,
+			 const struct sfdp_parameter_header *bfpt_header,
+			 const struct sfdp_bfpt *bfpt,
+			 struct spi_nor_flash_parameter *params);
+	int (*post_sfdp)(struct spi_nor *nor,
+			 struct spi_nor_flash_parameter *params);
+};
+
+struct flash_info {
+	char		*name;
+
+	/*
+	 * This array stores the ID bytes.
+	 * The first three bytes are the JEDIC ID.
+	 * JEDEC ID zero means "no ID" (mostly older chips).
+	 */
+	u8		id[SPI_NOR_MAX_ID_LEN];
+	u8		id_len;
+
+	/* The size listed here is what works with SPINOR_OP_SE, which isn't
+	 * necessarily called a "sector" by the vendor.
+	 */
+	unsigned	sector_size;
+	u16		n_sectors;
+
+	u16		page_size;
+	u16		addr_width;
+
+	u16		flags;
+#define SECT_4K			BIT(0)	/* SPINOR_OP_BE_4K works uniformly */
+#define SPI_NOR_NO_ERASE	BIT(1)	/* No erase command needed */
+#define SST_WRITE		BIT(2)	/* use SST byte programming */
+#define SPI_NOR_NO_FR		BIT(3)	/* Can't do fastread */
+#define SECT_4K_PMC		BIT(4)	/* SPINOR_OP_BE_4K_PMC works uniformly */
+#define SPI_NOR_DUAL_READ	BIT(5)	/* Flash supports Dual Read */
+#define SPI_NOR_QUAD_READ	BIT(6)	/* Flash supports Quad Read */
+#define USE_FSR			BIT(7)	/* use flag status register */
+#define SPI_NOR_HAS_LOCK	BIT(8)	/* Flash supports lock/unlock via SR */
+#define SPI_NOR_HAS_TB		BIT(9)	/*
+					 * Flash SR has Top/Bottom (TB) protect
+					 * bit. Must be used with
+					 * SPI_NOR_HAS_LOCK.
+					 */
+#define SPI_NOR_XSR_RDY		BIT(10)	/*
+					 * S3AN flashes have specific opcode to
+					 * read the status register.
+					 * Flags SPI_NOR_XSR_RDY and SPI_S3AN
+					 * use the same bit as one implies the
+					 * other, but we will get rid of
+					 * SPI_S3AN soon.
+					 */
+#define	SPI_S3AN		BIT(10)	/*
+					 * Xilinx Spartan 3AN In-System Flash
+					 * (MFR cannot be used for probing
+					 * because it has the same value as
+					 * ATMEL flashes)
+					 */
+#define SPI_NOR_4B_OPCODES	BIT(11)	/*
+					 * Use dedicated 4byte address op codes
+					 * to support memory size above 128Mib.
+					 */
+#define NO_CHIP_ERASE		BIT(12) /* Chip does not support chip erase */
+#define SPI_NOR_SKIP_SFDP	BIT(13)	/* Skip parsing of SFDP tables */
+#define USE_CLSR		BIT(14)	/* use CLSR command */
+
+	/* Part specific fixup hooks. */
+	const struct spi_nor_fixups *fixups;
+};
+
+/* Used when the "_ext_id" is two bytes at most */
+#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags)	\
+		.id = {							\
+			((_jedec_id) >> 16) & 0xff,			\
+			((_jedec_id) >> 8) & 0xff,			\
+			(_jedec_id) & 0xff,				\
+			((_ext_id) >> 8) & 0xff,			\
+			(_ext_id) & 0xff,				\
+			},						\
+		.id_len = (!(_jedec_id) ? 0 : (3 + ((_ext_id) ? 2 : 0))),	\
+		.sector_size = (_sector_size),				\
+		.n_sectors = (_n_sectors),				\
+		.page_size = 256,					\
+		.flags = (_flags),
+
+#define INFO6(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags)	\
+		.id = {							\
+			((_jedec_id) >> 16) & 0xff,			\
+			((_jedec_id) >> 8) & 0xff,			\
+			(_jedec_id) & 0xff,				\
+			((_ext_id) >> 16) & 0xff,			\
+			((_ext_id) >> 8) & 0xff,			\
+			(_ext_id) & 0xff,				\
+			},						\
+		.id_len = 6,						\
+		.sector_size = (_sector_size),				\
+		.n_sectors = (_n_sectors),				\
+		.page_size = 256,					\
+		.flags = (_flags),
+
+#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_width, _flags)	\
+		.sector_size = (_sector_size),				\
+		.n_sectors = (_n_sectors),				\
+		.page_size = (_page_size),				\
+		.addr_width = (_addr_width),				\
+		.flags = (_flags),
+
+#define S3AN_INFO(_jedec_id, _n_sectors, _page_size)			\
+		.id = {							\
+			((_jedec_id) >> 16) & 0xff,			\
+			((_jedec_id) >> 8) & 0xff,			\
+			(_jedec_id) & 0xff				\
+			},						\
+		.id_len = 3,						\
+		.sector_size = (8*_page_size),				\
+		.n_sectors = (_n_sectors),				\
+		.page_size = _page_size,				\
+		.addr_width = 3,					\
+		.flags = SPI_NOR_NO_FR | SPI_S3AN,
+
+#endif /* __LINUX_MTD_SPI_NOR_INTERNALS_H */
