@@ -39,7 +39,6 @@ CONFIG_MTD_BLOCK=y
CONFIG_MTD_DATAFLASH=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_ATMEL_SSC=y
@@ -61,7 +61,6 @@ CONFIG_MTD_DATAFLASH=y
CONFIG_MTD_BLOCK2MTD=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_GLUEBI=y
CONFIG_BLK_DEV_LOOP=y
@@ -50,7 +50,6 @@ CONFIG_MTD_BLOCK=y
CONFIG_MTD_DATAFLASH=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
CONFIG_BLK_DEV_LOOP=y
# CONFIG_MISC_DEVICES is not set
CONFIG_SCSI=y
@@ -49,7 +49,6 @@ CONFIG_MTD_BLOCK=y
CONFIG_MTD_DATAFLASH=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
CONFIG_BLK_DEV_LOOP=y
# CONFIG_MISC_DEVICES is not set
CONFIG_SCSI=y
@@ -406,46 +406,6 @@ config MTD_NAND_ATMEL
help
Enables support for NAND Flash / Smart Media Card interface
on Atmel AT91 and AVR32 processors.
-choice
- prompt "ECC management for NAND Flash / SmartMedia on AT91 / AVR32"
- depends on MTD_NAND_ATMEL
-
-config MTD_NAND_ATMEL_ECC_HW
- bool "Hardware ECC"
- depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9260 || AVR32
- help
- Use hardware ECC instead of software ECC when the chip
- supports it.
-
- The hardware ECC controller is capable of single bit error
- correction and 2-bit random detection per page.
-
- NB : hardware and software ECC schemes are incompatible.
- If you switch from one to another, you'll have to erase your
- mtd partition.
-
- If unsure, say Y
-
-config MTD_NAND_ATMEL_ECC_SOFT
- bool "Software ECC"
- help
- Use software ECC.
-
- NB : hardware and software ECC schemes are incompatible.
- If you switch from one to another, you'll have to erase your
- mtd partition.
-
-config MTD_NAND_ATMEL_ECC_NONE
- bool "No ECC (testing only, DANGEROUS)"
- depends on DEBUG_KERNEL
- help
- No ECC will be used.
- It's not a good idea and it should be reserved for testing
- purpose only.
-
- If unsure, say N
-
-endchoice
config MTD_NAND_PXA3xx
tristate "Support for NAND flash devices on PXA3xx"
The commit bf4289cba02b8cf770ecd7959ca70839f0dd9d3c removed the use of CONFIG_MTD_NAND_ATMEL_ECC_NONE and CONFIG_MTD_NAND_ATMEL_ECC_HW but the Kconfig file was forgotten. This patch remove those inoperative options. Signed-off-by: Richard Genoud <richard.genoud@gmail.com> --- arch/arm/configs/afeb9260_defconfig | 1 - arch/arm/configs/at91sam9263_defconfig | 1 - arch/arm/configs/qil-a9260_defconfig | 1 - arch/arm/configs/usb-a9260_defconfig | 1 - drivers/mtd/nand/Kconfig | 40 -------------------------------- 5 files changed, 0 insertions(+), 44 deletions(-)