| Message ID | 20210309112615.625-2-o.rempel@pengutronix.de |
|---|---|
| State | New |
| Headers | show |
| Series | remove different PHY fixups | expand |
On Tue, Mar 09, 2021 at 12:26:09PM +0100, Oleksij Rempel wrote: > Starting with: > > bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY") > > the micrel phy driver started respecting phy-mode for the KSZ9031 PHY. > At least with kernel v5.8 configuration provided by this fixup was > overwritten by the micrel driver. > > This fixup was providing following configuration: > > RX path: 2.58ns delay > rx -0.42 (left shift) + rx_clk +0.96ns (right shift) = > 1,38 + 1,2 internal RX delay = 2.58ns > TX path: 0.96ns delay > tx (no delay) + tx_clk 0.96ns (right shift) = 0.96ns > > This configuration is outside of the recommended RGMII clock skew delays > and about in the middle of: rgmii-idrx and rgmii-id > > Since most embedded systems do not have enough place to introduce > significant clock skew, rgmii-id is the way to go. > > In case this patch breaks network functionality on your system, build > kernel with enabled MICREL_PHY. If it is still not working then try > following device tree options: > 1. Set (or change) phy-mode in DT to: > phy-mode = "rgmii-id"; > This actives internal delay for both RX and TX. > 1. Set (or change) phy-mode in DT to: > phy-mode = "rgmii-idrx"; > This actives internal delay for RX only. > 3. Use following DT properties: > phy-mode = "rgmii"; > txen-skew-psec = <0>; > rxdv-skew-psec = <0>; > rxd0-skew-psec = <0>; > rxd1-skew-psec = <0>; > rxd2-skew-psec = <0>; > rxd3-skew-psec = <0>; > rxc-skew-psec = <1860>; > txc-skew-psec = <1860>; > This activates the internal delays for RX and TX, with the value as > the fixup that is removed in this patch. > > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> > Acked-by: Philippe Schenker <philippe.schenker@toradex.com> > --- > arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts | 2 +- > arch/arm/mach-imx/mach-imx6q.c | 23 ----------------------- I have different branch for DTS and mach-imx change. Please split the changes. Shawn > 2 files changed, 1 insertion(+), 24 deletions(-) > > diff --git a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts > index fa2307d8ce86..c713ac03b3b9 100644 > --- a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts > +++ b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts > @@ -112,7 +112,7 @@ flash: m25p80@0 { > &fec { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_enet>; > - phy-mode = "rgmii"; > + phy-mode = "rgmii-id"; > phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; > phy-supply = <&vgen2_1v2_eth>; > status = "okay"; > diff --git a/arch/arm/mach-imx/mach-imx6q.c b/arch/arm/mach-imx/mach-imx6q.c > index 703998ebb52e..78205f90da27 100644 > --- a/arch/arm/mach-imx/mach-imx6q.c > +++ b/arch/arm/mach-imx/mach-imx6q.c > @@ -40,27 +40,6 @@ static int ksz9021rn_phy_fixup(struct phy_device *phydev) > return 0; > } > > -static void mmd_write_reg(struct phy_device *dev, int device, int reg, int val) > -{ > - phy_write(dev, 0x0d, device); > - phy_write(dev, 0x0e, reg); > - phy_write(dev, 0x0d, (1 << 14) | device); > - phy_write(dev, 0x0e, val); > -} > - > -static int ksz9031rn_phy_fixup(struct phy_device *dev) > -{ > - /* > - * min rx data delay, max rx/tx clock delay, > - * min rx/tx control delay > - */ > - mmd_write_reg(dev, 2, 4, 0); > - mmd_write_reg(dev, 2, 5, 0); > - mmd_write_reg(dev, 2, 8, 0x003ff); > - > - return 0; > -} > - > /* > * fixup for PLX PEX8909 bridge to configure GPIO1-7 as output High > * as they are used for slots1-7 PERST# > @@ -152,8 +131,6 @@ static void __init imx6q_enet_phy_init(void) > if (IS_BUILTIN(CONFIG_PHYLIB)) { > phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK, > ksz9021rn_phy_fixup); > - phy_register_fixup_for_uid(PHY_ID_KSZ9031, MICREL_PHY_ID_MASK, > - ksz9031rn_phy_fixup); > phy_register_fixup_for_uid(PHY_ID_AR8031, 0xffffffef, > ar8031_phy_fixup); > phy_register_fixup_for_uid(PHY_ID_AR8035, 0xffffffef, > -- > 2.29.2 >
diff --git a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts index fa2307d8ce86..c713ac03b3b9 100644 --- a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts +++ b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts @@ -112,7 +112,7 @@ flash: m25p80@0 { &fec { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet>; - phy-mode = "rgmii"; + phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; phy-supply = <&vgen2_1v2_eth>; status = "okay"; diff --git a/arch/arm/mach-imx/mach-imx6q.c b/arch/arm/mach-imx/mach-imx6q.c index 703998ebb52e..78205f90da27 100644 --- a/arch/arm/mach-imx/mach-imx6q.c +++ b/arch/arm/mach-imx/mach-imx6q.c @@ -40,27 +40,6 @@ static int ksz9021rn_phy_fixup(struct phy_device *phydev) return 0; } -static void mmd_write_reg(struct phy_device *dev, int device, int reg, int val) -{ - phy_write(dev, 0x0d, device); - phy_write(dev, 0x0e, reg); - phy_write(dev, 0x0d, (1 << 14) | device); - phy_write(dev, 0x0e, val); -} - -static int ksz9031rn_phy_fixup(struct phy_device *dev) -{ - /* - * min rx data delay, max rx/tx clock delay, - * min rx/tx control delay - */ - mmd_write_reg(dev, 2, 4, 0); - mmd_write_reg(dev, 2, 5, 0); - mmd_write_reg(dev, 2, 8, 0x003ff); - - return 0; -} - /* * fixup for PLX PEX8909 bridge to configure GPIO1-7 as output High * as they are used for slots1-7 PERST# @@ -152,8 +131,6 @@ static void __init imx6q_enet_phy_init(void) if (IS_BUILTIN(CONFIG_PHYLIB)) { phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK, ksz9021rn_phy_fixup); - phy_register_fixup_for_uid(PHY_ID_KSZ9031, MICREL_PHY_ID_MASK, - ksz9031rn_phy_fixup); phy_register_fixup_for_uid(PHY_ID_AR8031, 0xffffffef, ar8031_phy_fixup); phy_register_fixup_for_uid(PHY_ID_AR8035, 0xffffffef,
Starting with: bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY") the micrel phy driver started respecting phy-mode for the KSZ9031 PHY. At least with kernel v5.8 configuration provided by this fixup was overwritten by the micrel driver. This fixup was providing following configuration: RX path: 2.58ns delay rx -0.42 (left shift) + rx_clk +0.96ns (right shift) = 1,38 + 1,2 internal RX delay = 2.58ns TX path: 0.96ns delay tx (no delay) + tx_clk 0.96ns (right shift) = 0.96ns This configuration is outside of the recommended RGMII clock skew delays and about in the middle of: rgmii-idrx and rgmii-id Since most embedded systems do not have enough place to introduce significant clock skew, rgmii-id is the way to go. In case this patch breaks network functionality on your system, build kernel with enabled MICREL_PHY. If it is still not working then try following device tree options: 1. Set (or change) phy-mode in DT to: phy-mode = "rgmii-id"; This actives internal delay for both RX and TX. 1. Set (or change) phy-mode in DT to: phy-mode = "rgmii-idrx"; This actives internal delay for RX only. 3. Use following DT properties: phy-mode = "rgmii"; txen-skew-psec = <0>; rxdv-skew-psec = <0>; rxd0-skew-psec = <0>; rxd1-skew-psec = <0>; rxd2-skew-psec = <0>; rxd3-skew-psec = <0>; rxc-skew-psec = <1860>; txc-skew-psec = <1860>; This activates the internal delays for RX and TX, with the value as the fixup that is removed in this patch. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Acked-by: Philippe Schenker <philippe.schenker@toradex.com> --- arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts | 2 +- arch/arm/mach-imx/mach-imx6q.c | 23 ----------------------- 2 files changed, 1 insertion(+), 24 deletions(-)