| Message ID | 1530119544-30023-3-git-send-email-pawel.mikolaj.chmiel@gmail.com |
|---|---|
| State | New |
| Headers | show |
| Series | Initial support for Samsung Galaxy S and Galaxy S 4G | expand |
On 27 June 2018 at 19:12, Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> wrote: > This DTS file have initial support Samsung Aries based phones. > Initial version have support for: > - sdcard > - internal memory (present only on non 4g variant) > - max8998 pmic and rtc > - max17040 fuel gauge > - gpio keys > - fimd (no panel driver yet) > - usb (peripherial mode) > - wifi > > Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> > --- > > Changes from v1: > - Removed duplicated and unneeded headers > - Corrected node names > - Added missing spaces > - Removed unneeded pinctrl and sorted entries > - Set correct interrupt type for max8998 pmic > - Add missing regulators > --- > --- > arch/arm/boot/dts/s5pv210-aries.dtsi | 423 +++++++++++++++++++++++++++++++++++ > 1 file changed, 423 insertions(+) > create mode 100644 arch/arm/boot/dts/s5pv210-aries.dtsi > > diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi > new file mode 100644 > index 000000000000..61b6cf76265f > --- /dev/null > +++ b/arch/arm/boot/dts/s5pv210-aries.dtsi > @@ -0,0 +1,423 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Samsung's S5PV210 based Galaxy Aries board device tree source > + */ > + > +/dts-v1/; > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/irq.h> > +#include "s5pv210.dtsi" > + > +/ { > + compatible = "samsung,aries", "samsung,s5pv210"; > + > + aliases { > + i2c6 = &i2c_pmic; > + i2c9 = &i2c_fuel; > + }; > + > + memory@30000000 { > + device_type = "memory"; > + reg = <0x30000000 0x05000000 > + 0x40000000 0x10000000 > + 0x50000000 0x08000000>; > + }; > + > + wifi_pwrseq: wifi-pwrseq { > + compatible = "mmc-pwrseq-simple"; > + reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&wlan_gpio_rst>; > + post-power-on-delay-ms = <500>; > + power-off-delay-us = <500>; > + }; > + > + i2c_pmic: i2c-gpio-0 { > + compatible = "i2c-gpio"; > + sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + i2c-gpio,delay-us = <2>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pmic@66 { > + compatible = "maxim,max8998"; > + reg = <0x66>; > + interrupt-parent = <&gph0>; > + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; > + > + max8998,pmic-buck1-default-dvs-idx = <1>; > + max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>, > + <&gph0 4 GPIO_ACTIVE_HIGH>; > + max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>, > + <1050000>, <950000>; > + > + max8998,pmic-buck2-default-dvs-idx = <0>; > + max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>; > + max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>; > + > + regulators { > + ldo2_reg: LDO2 { > + regulator-name = "VALIVE_1.2V"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + > + regulator-state-mem { > + regulator-on-in-suspend; > + }; > + }; > + > + ldo3_reg: LDO3 { > + regulator-name = "VUSB_1.1V"; > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo4_reg: LDO4 { > + regulator-name = "VADC_3.3V"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo5_reg: LDO5 { > + regulator-name = "VTF_2.8V"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo6_reg: LDO6 { > + regulator-name = "LDO6"; > + regulator-min-microvolt = <1600000>; > + regulator-max-microvolt = <3600000>; > + }; > + > + ldo7_reg: LDO7 { > + regulator-name = "VLCD_1.8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + /* Till we get panel driver */ > + regulator-always-on; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo8_reg: LDO8 { > + regulator-name = "VUSB_3.3V"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo9_reg: LDO9 { > + regulator-name = "VCC_2.8V_PDA"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-always-on; > + }; > + > + ldo10_reg: LDO10 { > + regulator-name = "VPLL_1.2V"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + > + regulator-state-mem { > + regulator-on-in-suspend; > + }; > + }; > + > + ldo11_reg: LDO11 { > + regulator-name = "CAM_AF_3.0V"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo12_reg: LDO12 { > + regulator-name = "CAM_SENSOR_CORE_1.2V"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo13_reg: LDO13 { > + regulator-name = "VGA_VDDIO_2.8V"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo14_reg: LDO14 { > + regulator-name = "VGA_DVDD_1.8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo15_reg: LDO15 { > + regulator-name = "CAM_ISP_HOST_2.8V"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo16_reg: LDO16 { > + regulator-name = "VGA_AVDD_2.8V"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo17_reg: LDO17 { > + regulator-name = "VCC_3.0V_LCD"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + /* Till we get panel driver */ > + regulator-always-on; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + buck1_reg: BUCK1 { > + regulator-name = "vddarm"; > + regulator-min-microvolt = <750000>; > + regulator-max-microvolt = <1500000>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + regulator-suspend-microvolt = <1250000>; > + }; > + }; > + > + buck2_reg: BUCK2 { > + regulator-name = "vddint"; > + regulator-min-microvolt = <750000>; > + regulator-max-microvolt = <1500000>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + regulator-suspend-microvolt = <1100000>; > + }; > + }; > + > + buck3_reg: BUCK3 { > + regulator-name = "VCC_1.8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + }; > + > + buck4_reg: BUCK4 { > + regulator-name = "CAM_ISP_CORE_1.2V"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ap32khz_reg: EN32KHz-AP { > + regulator-name = "32KHz AP"; > + regulator-always-on; > + }; > + > + cp32khz_reg: EN32KHz-CP { > + regulator-name = "32KHz CP"; > + }; > + > + vichg_reg: ENVICHG { > + regulator-name = "VICHG"; > + regulator-always-on; > + }; > + > + safe1_sreg: ESAFEOUT1 { > + regulator-name = "SAFEOUT1"; > + }; > + > + safe2_sreg: ESAFEOUT2 { > + regulator-name = "SAFEOUT2"; > + }; > + }; > + }; > + }; > + > + i2c_fuel: i2c-gpio-1 { > + compatible = "i2c-gpio"; > + sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + i2c-gpio,delay-us = <2>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + fuelgauge@36 { > + compatible = "maxim,max17040"; > + interrupt-parent = <&vic0>; > + interrupts = <7>; > + reg = <0x36>; > + }; > + }; > +}; > + > +&xusbxti { > + clock-frequency = <24000000>; > +}; > + > +&pinctrl0 { Thanks for changes. You missed one part - ordering the labels here alphabetically, so: &fimd {} &hsotg {} ... &xusbxti {} Best regards, Krzysztof
On 28 June 2018 at 09:41, Krzysztof Kozlowski <krzk@kernel.org> wrote: > On 27 June 2018 at 19:12, Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> wrote: >> This DTS file have initial support Samsung Aries based phones. >> Initial version have support for: >> - sdcard >> - internal memory (present only on non 4g variant) >> - max8998 pmic and rtc >> - max17040 fuel gauge >> - gpio keys >> - fimd (no panel driver yet) >> - usb (peripherial mode) >> - wifi >> >> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> >> --- >> >> Changes from v1: >> - Removed duplicated and unneeded headers >> - Corrected node names >> - Added missing spaces >> - Removed unneeded pinctrl and sorted entries >> - Set correct interrupt type for max8998 pmic >> - Add missing regulators >> --- >> --- >> arch/arm/boot/dts/s5pv210-aries.dtsi | 423 +++++++++++++++++++++++++++++++++++ >> 1 file changed, 423 insertions(+) >> create mode 100644 arch/arm/boot/dts/s5pv210-aries.dtsi >> >> diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi >> new file mode 100644 >> index 000000000000..61b6cf76265f >> --- /dev/null >> +++ b/arch/arm/boot/dts/s5pv210-aries.dtsi >> @@ -0,0 +1,423 @@ >> +// SPDX-License-Identifier: GPL-2.0 >> +/* >> + * Samsung's S5PV210 based Galaxy Aries board device tree source >> + */ >> + >> +/dts-v1/; >> +#include <dt-bindings/gpio/gpio.h> >> +#include <dt-bindings/interrupt-controller/irq.h> >> +#include "s5pv210.dtsi" >> + >> +/ { >> + compatible = "samsung,aries", "samsung,s5pv210"; >> + >> + aliases { >> + i2c6 = &i2c_pmic; >> + i2c9 = &i2c_fuel; >> + }; >> + >> + memory@30000000 { >> + device_type = "memory"; >> + reg = <0x30000000 0x05000000 >> + 0x40000000 0x10000000 >> + 0x50000000 0x08000000>; >> + }; >> + >> + wifi_pwrseq: wifi-pwrseq { >> + compatible = "mmc-pwrseq-simple"; >> + reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&wlan_gpio_rst>; >> + post-power-on-delay-ms = <500>; >> + power-off-delay-us = <500>; >> + }; >> + >> + i2c_pmic: i2c-gpio-0 { >> + compatible = "i2c-gpio"; >> + sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; >> + scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; >> + i2c-gpio,delay-us = <2>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + pmic@66 { >> + compatible = "maxim,max8998"; >> + reg = <0x66>; >> + interrupt-parent = <&gph0>; >> + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; >> + >> + max8998,pmic-buck1-default-dvs-idx = <1>; >> + max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>, >> + <&gph0 4 GPIO_ACTIVE_HIGH>; >> + max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>, >> + <1050000>, <950000>; >> + >> + max8998,pmic-buck2-default-dvs-idx = <0>; >> + max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>; >> + max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>; >> + >> + regulators { >> + ldo2_reg: LDO2 { >> + regulator-name = "VALIVE_1.2V"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-always-on; >> + >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + }; >> + }; >> + >> + ldo3_reg: LDO3 { >> + regulator-name = "VUSB_1.1V"; >> + regulator-min-microvolt = <1100000>; >> + regulator-max-microvolt = <1100000>; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + ldo4_reg: LDO4 { >> + regulator-name = "VADC_3.3V"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-always-on; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + ldo5_reg: LDO5 { >> + regulator-name = "VTF_2.8V"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <2800000>; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + ldo6_reg: LDO6 { >> + regulator-name = "LDO6"; >> + regulator-min-microvolt = <1600000>; >> + regulator-max-microvolt = <3600000>; >> + }; >> + >> + ldo7_reg: LDO7 { >> + regulator-name = "VLCD_1.8V"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + /* Till we get panel driver */ >> + regulator-always-on; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + ldo8_reg: LDO8 { >> + regulator-name = "VUSB_3.3V"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + ldo9_reg: LDO9 { >> + regulator-name = "VCC_2.8V_PDA"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <2800000>; >> + regulator-always-on; >> + }; >> + >> + ldo10_reg: LDO10 { >> + regulator-name = "VPLL_1.2V"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-always-on; >> + >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + }; >> + }; >> + >> + ldo11_reg: LDO11 { >> + regulator-name = "CAM_AF_3.0V"; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3000000>; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + ldo12_reg: LDO12 { >> + regulator-name = "CAM_SENSOR_CORE_1.2V"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + ldo13_reg: LDO13 { >> + regulator-name = "VGA_VDDIO_2.8V"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <2800000>; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + ldo14_reg: LDO14 { >> + regulator-name = "VGA_DVDD_1.8V"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + ldo15_reg: LDO15 { >> + regulator-name = "CAM_ISP_HOST_2.8V"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <2800000>; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + ldo16_reg: LDO16 { >> + regulator-name = "VGA_AVDD_2.8V"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <2800000>; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + ldo17_reg: LDO17 { >> + regulator-name = "VCC_3.0V_LCD"; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3000000>; >> + /* Till we get panel driver */ >> + regulator-always-on; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + buck1_reg: BUCK1 { >> + regulator-name = "vddarm"; >> + regulator-min-microvolt = <750000>; >> + regulator-max-microvolt = <1500000>; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + regulator-suspend-microvolt = <1250000>; >> + }; >> + }; >> + >> + buck2_reg: BUCK2 { >> + regulator-name = "vddint"; >> + regulator-min-microvolt = <750000>; >> + regulator-max-microvolt = <1500000>; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + regulator-suspend-microvolt = <1100000>; >> + }; >> + }; >> + >> + buck3_reg: BUCK3 { >> + regulator-name = "VCC_1.8V"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-always-on; >> + }; >> + >> + buck4_reg: BUCK4 { >> + regulator-name = "CAM_ISP_CORE_1.2V"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + ap32khz_reg: EN32KHz-AP { >> + regulator-name = "32KHz AP"; >> + regulator-always-on; >> + }; >> + >> + cp32khz_reg: EN32KHz-CP { >> + regulator-name = "32KHz CP"; >> + }; >> + >> + vichg_reg: ENVICHG { >> + regulator-name = "VICHG"; >> + regulator-always-on; >> + }; >> + >> + safe1_sreg: ESAFEOUT1 { >> + regulator-name = "SAFEOUT1"; >> + }; >> + >> + safe2_sreg: ESAFEOUT2 { >> + regulator-name = "SAFEOUT2"; >> + }; >> + }; >> + }; >> + }; >> + >> + i2c_fuel: i2c-gpio-1 { >> + compatible = "i2c-gpio"; >> + sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; >> + scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; >> + i2c-gpio,delay-us = <2>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + fuelgauge@36 { >> + compatible = "maxim,max17040"; >> + interrupt-parent = <&vic0>; >> + interrupts = <7>; >> + reg = <0x36>; >> + }; >> + }; >> +}; >> + >> +&xusbxti { >> + clock-frequency = <24000000>; >> +}; >> + >> +&pinctrl0 { > > Thanks for changes. You missed one part - ordering the labels here > alphabetically, so: > > &fimd {} > &hsotg {} > ... > &xusbxti {} Ah, now I see that you changed the order of nodes inside pinctrl. No need. These were good - ordered by pin names (so gpb, gpg, gph, gpj). I was referring only to the top-level overrides by label. The point is when people add new overrides, they tend to add them to the end... and this brings conflicts with multiple edits at the same time. When node overrides are ordered and new entries are being added, the chance of conflicts is reduced. BR, Krzysztof
On Thursday, June 28, 2018 9:48:48 AM CEST Krzysztof Kozlowski wrote: > On 28 June 2018 at 09:41, Krzysztof Kozlowski <krzk@kernel.org> wrote: > > On 27 June 2018 at 19:12, Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> wrote: > >> This DTS file have initial support Samsung Aries based phones. > >> Initial version have support for: > >> - sdcard > >> - internal memory (present only on non 4g variant) > >> - max8998 pmic and rtc > >> - max17040 fuel gauge > >> - gpio keys > >> - fimd (no panel driver yet) > >> - usb (peripherial mode) > >> - wifi > >> > >> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> > >> --- > >> > >> Changes from v1: > >> - Removed duplicated and unneeded headers > >> - Corrected node names > >> - Added missing spaces > >> - Removed unneeded pinctrl and sorted entries > >> - Set correct interrupt type for max8998 pmic > >> - Add missing regulators > >> --- > >> --- > >> arch/arm/boot/dts/s5pv210-aries.dtsi | 423 +++++++++++++++++++++++++++++++++++ > >> 1 file changed, 423 insertions(+) > >> create mode 100644 arch/arm/boot/dts/s5pv210-aries.dtsi > >> > >> diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi > >> new file mode 100644 > >> index 000000000000..61b6cf76265f > >> --- /dev/null > >> +++ b/arch/arm/boot/dts/s5pv210-aries.dtsi > >> @@ -0,0 +1,423 @@ > >> +// SPDX-License-Identifier: GPL-2.0 > >> +/* > >> + * Samsung's S5PV210 based Galaxy Aries board device tree source > >> + */ > >> + > >> +/dts-v1/; > >> +#include <dt-bindings/gpio/gpio.h> > >> +#include <dt-bindings/interrupt-controller/irq.h> > >> +#include "s5pv210.dtsi" > >> + > >> +/ { > >> + compatible = "samsung,aries", "samsung,s5pv210"; > >> + > >> + aliases { > >> + i2c6 = &i2c_pmic; > >> + i2c9 = &i2c_fuel; > >> + }; > >> + > >> + memory@30000000 { > >> + device_type = "memory"; > >> + reg = <0x30000000 0x05000000 > >> + 0x40000000 0x10000000 > >> + 0x50000000 0x08000000>; > >> + }; > >> + > >> + wifi_pwrseq: wifi-pwrseq { > >> + compatible = "mmc-pwrseq-simple"; > >> + reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>; > >> + pinctrl-names = "default"; > >> + pinctrl-0 = <&wlan_gpio_rst>; > >> + post-power-on-delay-ms = <500>; > >> + power-off-delay-us = <500>; > >> + }; > >> + > >> + i2c_pmic: i2c-gpio-0 { > >> + compatible = "i2c-gpio"; > >> + sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > >> + scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > >> + i2c-gpio,delay-us = <2>; > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + > >> + pmic@66 { > >> + compatible = "maxim,max8998"; > >> + reg = <0x66>; > >> + interrupt-parent = <&gph0>; > >> + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; > >> + > >> + max8998,pmic-buck1-default-dvs-idx = <1>; > >> + max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>, > >> + <&gph0 4 GPIO_ACTIVE_HIGH>; > >> + max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>, > >> + <1050000>, <950000>; > >> + > >> + max8998,pmic-buck2-default-dvs-idx = <0>; > >> + max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>; > >> + max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>; > >> + > >> + regulators { > >> + ldo2_reg: LDO2 { > >> + regulator-name = "VALIVE_1.2V"; > >> + regulator-min-microvolt = <1200000>; > >> + regulator-max-microvolt = <1200000>; > >> + regulator-always-on; > >> + > >> + regulator-state-mem { > >> + regulator-on-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo3_reg: LDO3 { > >> + regulator-name = "VUSB_1.1V"; > >> + regulator-min-microvolt = <1100000>; > >> + regulator-max-microvolt = <1100000>; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo4_reg: LDO4 { > >> + regulator-name = "VADC_3.3V"; > >> + regulator-min-microvolt = <3300000>; > >> + regulator-max-microvolt = <3300000>; > >> + regulator-always-on; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo5_reg: LDO5 { > >> + regulator-name = "VTF_2.8V"; > >> + regulator-min-microvolt = <2800000>; > >> + regulator-max-microvolt = <2800000>; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo6_reg: LDO6 { > >> + regulator-name = "LDO6"; > >> + regulator-min-microvolt = <1600000>; > >> + regulator-max-microvolt = <3600000>; > >> + }; > >> + > >> + ldo7_reg: LDO7 { > >> + regulator-name = "VLCD_1.8V"; > >> + regulator-min-microvolt = <1800000>; > >> + regulator-max-microvolt = <1800000>; > >> + /* Till we get panel driver */ > >> + regulator-always-on; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo8_reg: LDO8 { > >> + regulator-name = "VUSB_3.3V"; > >> + regulator-min-microvolt = <3300000>; > >> + regulator-max-microvolt = <3300000>; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo9_reg: LDO9 { > >> + regulator-name = "VCC_2.8V_PDA"; > >> + regulator-min-microvolt = <2800000>; > >> + regulator-max-microvolt = <2800000>; > >> + regulator-always-on; > >> + }; > >> + > >> + ldo10_reg: LDO10 { > >> + regulator-name = "VPLL_1.2V"; > >> + regulator-min-microvolt = <1200000>; > >> + regulator-max-microvolt = <1200000>; > >> + regulator-always-on; > >> + > >> + regulator-state-mem { > >> + regulator-on-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo11_reg: LDO11 { > >> + regulator-name = "CAM_AF_3.0V"; > >> + regulator-min-microvolt = <3000000>; > >> + regulator-max-microvolt = <3000000>; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo12_reg: LDO12 { > >> + regulator-name = "CAM_SENSOR_CORE_1.2V"; > >> + regulator-min-microvolt = <1200000>; > >> + regulator-max-microvolt = <1200000>; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo13_reg: LDO13 { > >> + regulator-name = "VGA_VDDIO_2.8V"; > >> + regulator-min-microvolt = <2800000>; > >> + regulator-max-microvolt = <2800000>; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo14_reg: LDO14 { > >> + regulator-name = "VGA_DVDD_1.8V"; > >> + regulator-min-microvolt = <1800000>; > >> + regulator-max-microvolt = <1800000>; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo15_reg: LDO15 { > >> + regulator-name = "CAM_ISP_HOST_2.8V"; > >> + regulator-min-microvolt = <2800000>; > >> + regulator-max-microvolt = <2800000>; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo16_reg: LDO16 { > >> + regulator-name = "VGA_AVDD_2.8V"; > >> + regulator-min-microvolt = <2800000>; > >> + regulator-max-microvolt = <2800000>; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + ldo17_reg: LDO17 { > >> + regulator-name = "VCC_3.0V_LCD"; > >> + regulator-min-microvolt = <3000000>; > >> + regulator-max-microvolt = <3000000>; > >> + /* Till we get panel driver */ > >> + regulator-always-on; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + buck1_reg: BUCK1 { > >> + regulator-name = "vddarm"; > >> + regulator-min-microvolt = <750000>; > >> + regulator-max-microvolt = <1500000>; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + regulator-suspend-microvolt = <1250000>; > >> + }; > >> + }; > >> + > >> + buck2_reg: BUCK2 { > >> + regulator-name = "vddint"; > >> + regulator-min-microvolt = <750000>; > >> + regulator-max-microvolt = <1500000>; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + regulator-suspend-microvolt = <1100000>; > >> + }; > >> + }; > >> + > >> + buck3_reg: BUCK3 { > >> + regulator-name = "VCC_1.8V"; > >> + regulator-min-microvolt = <1800000>; > >> + regulator-max-microvolt = <1800000>; > >> + regulator-always-on; > >> + }; > >> + > >> + buck4_reg: BUCK4 { > >> + regulator-name = "CAM_ISP_CORE_1.2V"; > >> + regulator-min-microvolt = <1200000>; > >> + regulator-max-microvolt = <1200000>; > >> + > >> + regulator-state-mem { > >> + regulator-off-in-suspend; > >> + }; > >> + }; > >> + > >> + ap32khz_reg: EN32KHz-AP { > >> + regulator-name = "32KHz AP"; > >> + regulator-always-on; > >> + }; > >> + > >> + cp32khz_reg: EN32KHz-CP { > >> + regulator-name = "32KHz CP"; > >> + }; > >> + > >> + vichg_reg: ENVICHG { > >> + regulator-name = "VICHG"; > >> + regulator-always-on; > >> + }; > >> + > >> + safe1_sreg: ESAFEOUT1 { > >> + regulator-name = "SAFEOUT1"; > >> + }; > >> + > >> + safe2_sreg: ESAFEOUT2 { > >> + regulator-name = "SAFEOUT2"; > >> + }; > >> + }; > >> + }; > >> + }; > >> + > >> + i2c_fuel: i2c-gpio-1 { > >> + compatible = "i2c-gpio"; > >> + sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > >> + scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > >> + i2c-gpio,delay-us = <2>; > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + > >> + fuelgauge@36 { > >> + compatible = "maxim,max17040"; > >> + interrupt-parent = <&vic0>; > >> + interrupts = <7>; > >> + reg = <0x36>; > >> + }; > >> + }; > >> +}; > >> + > >> +&xusbxti { > >> + clock-frequency = <24000000>; > >> +}; > >> + > >> +&pinctrl0 { > > > > Thanks for changes. You missed one part - ordering the labels here > > alphabetically, so: > > > > &fimd {} > > &hsotg {} > > ... > > &xusbxti {} > > Ah, now I see that you changed the order of nodes inside pinctrl. No > need. These were good - ordered by pin names (so gpb, gpg, gph, gpj). > I was referring only to the top-level overrides by label. The point is > when people add new overrides, they tend to add them to the end... and > this brings conflicts with multiple edits at the same time. When node > overrides are ordered and new entries are being added, the chance of > conflicts is reduced. > Ok now it's clear for me, will fix this (finally) in v3. Thanks > BR, > Krzysztof >
diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi new file mode 100644 index 000000000000..61b6cf76265f --- /dev/null +++ b/arch/arm/boot/dts/s5pv210-aries.dtsi @@ -0,0 +1,423 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Samsung's S5PV210 based Galaxy Aries board device tree source + */ + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include "s5pv210.dtsi" + +/ { + compatible = "samsung,aries", "samsung,s5pv210"; + + aliases { + i2c6 = &i2c_pmic; + i2c9 = &i2c_fuel; + }; + + memory@30000000 { + device_type = "memory"; + reg = <0x30000000 0x05000000 + 0x40000000 0x10000000 + 0x50000000 0x08000000>; + }; + + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_gpio_rst>; + post-power-on-delay-ms = <500>; + power-off-delay-us = <500>; + }; + + i2c_pmic: i2c-gpio-0 { + compatible = "i2c-gpio"; + sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + + pmic@66 { + compatible = "maxim,max8998"; + reg = <0x66>; + interrupt-parent = <&gph0>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + + max8998,pmic-buck1-default-dvs-idx = <1>; + max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>, + <&gph0 4 GPIO_ACTIVE_HIGH>; + max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>, + <1050000>, <950000>; + + max8998,pmic-buck2-default-dvs-idx = <0>; + max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>; + max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>; + + regulators { + ldo2_reg: LDO2 { + regulator-name = "VALIVE_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + ldo3_reg: LDO3 { + regulator-name = "VUSB_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo4_reg: LDO4 { + regulator-name = "VADC_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo5_reg: LDO5 { + regulator-name = "VTF_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo6_reg: LDO6 { + regulator-name = "LDO6"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <3600000>; + }; + + ldo7_reg: LDO7 { + regulator-name = "VLCD_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + /* Till we get panel driver */ + regulator-always-on; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo8_reg: LDO8 { + regulator-name = "VUSB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo9_reg: LDO9 { + regulator-name = "VCC_2.8V_PDA"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + ldo10_reg: LDO10 { + regulator-name = "VPLL_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + ldo11_reg: LDO11 { + regulator-name = "CAM_AF_3.0V"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo12_reg: LDO12 { + regulator-name = "CAM_SENSOR_CORE_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo13_reg: LDO13 { + regulator-name = "VGA_VDDIO_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo14_reg: LDO14 { + regulator-name = "VGA_DVDD_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo15_reg: LDO15 { + regulator-name = "CAM_ISP_HOST_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo16_reg: LDO16 { + regulator-name = "VGA_AVDD_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo17_reg: LDO17 { + regulator-name = "VCC_3.0V_LCD"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + /* Till we get panel driver */ + regulator-always-on; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck1_reg: BUCK1 { + regulator-name = "vddarm"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <1250000>; + }; + }; + + buck2_reg: BUCK2 { + regulator-name = "vddint"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <1100000>; + }; + }; + + buck3_reg: BUCK3 { + regulator-name = "VCC_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "CAM_ISP_CORE_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ap32khz_reg: EN32KHz-AP { + regulator-name = "32KHz AP"; + regulator-always-on; + }; + + cp32khz_reg: EN32KHz-CP { + regulator-name = "32KHz CP"; + }; + + vichg_reg: ENVICHG { + regulator-name = "VICHG"; + regulator-always-on; + }; + + safe1_sreg: ESAFEOUT1 { + regulator-name = "SAFEOUT1"; + }; + + safe2_sreg: ESAFEOUT2 { + regulator-name = "SAFEOUT2"; + }; + }; + }; + }; + + i2c_fuel: i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + + fuelgauge@36 { + compatible = "maxim,max17040"; + interrupt-parent = <&vic0>; + interrupts = <7>; + reg = <0x36>; + }; + }; +}; + +&xusbxti { + clock-frequency = <24000000>; +}; + +&pinctrl0 { + wifi_host_wake: wifi-host-wake { + samsung,pins = "gph2-4"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + wifi_wake: wifi-wake { + samsung,pins = "gph3-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; + }; + + wlan_bt_en: wlan-bt-en { + samsung,pins = "gpb-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; + samsung,pin-val = <1>; + }; + + wlan_gpio_rst: wlan-gpio-rst { + samsung,pins = "gpg1-2"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; + }; + + tf_detect: tf-detect { + samsung,pins = "gph3-4"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&sdhci1 { + #address-cells = <1>; + #size-cells = <0>; + + bus-width = <4>; + max-frequency = <38400000>; + pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus4 &wifi_wake &wifi_host_wake &wlan_bt_en>; + pinctrl-names = "default"; + cap-sd-highspeed; + cap-mmc-highspeed; + + mmc-pwrseq = <&wifi_pwrseq>; + non-removable; + status = "okay"; + + wlan@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&gph2>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host-wake"; + }; +}; + +&sdhci2 { + bus-width = <4>; + cd-gpios = <&gph3 4 GPIO_ACTIVE_LOW>; + vmmc-supply = <&ldo5_reg>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &tf_detect>; + pinctrl-names = "default"; + status = "okay"; +}; + +&hsotg { + vusb_a-supply = <&ldo8_reg>; + vusb_d-supply = <&ldo3_reg>; + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbphy { + status = "okay"; + vbus-supply = <&safe1_sreg>; +}; + +&fimd { + pinctrl-names = "default"; + pinctrl-0 = <&lcd_clk &lcd_data24>; + status = "okay"; + + samsung,invert-vden; + samsung,invert-vclk; + #address-cells = <1>; + #size-cells = <0>; + + display-timings { + native-mode = <&timing0>; + + timing0: timing@0 { + /* 480x800@60Hz */ + clock-frequency = <25628040>; + hactive = <480>; + vactive = <800>; + hfront-porch = <16>; + hback-porch = <16>; + hsync-len = <2>; + vfront-porch = <28>; + vback-porch = <1>; + vsync-len = <2>; + }; + }; +};
This DTS file have initial support Samsung Aries based phones. Initial version have support for: - sdcard - internal memory (present only on non 4g variant) - max8998 pmic and rtc - max17040 fuel gauge - gpio keys - fimd (no panel driver yet) - usb (peripherial mode) - wifi Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> --- Changes from v1: - Removed duplicated and unneeded headers - Corrected node names - Added missing spaces - Removed unneeded pinctrl and sorted entries - Set correct interrupt type for max8998 pmic - Add missing regulators --- --- arch/arm/boot/dts/s5pv210-aries.dtsi | 423 +++++++++++++++++++++++++++++++++++ 1 file changed, 423 insertions(+) create mode 100644 arch/arm/boot/dts/s5pv210-aries.dtsi