Message ID | 1515514200-9801-1-git-send-email-s.riedmueller@phytec.de |
---|---|
Headers | show |
Series | ARM: dts: Add PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira carrier board support | expand |
Hi Shawn, I noticed this patch stack did not find its way into your next branch yet. Is there anything I can do to speed up the process? Thanks, Stefan On 09.01.2018 17:09, Stefan Riedmueller wrote: > This patchset adds support for the PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira. > > Following boards are included: > phyBOARD-Mira with phyCORE-i.MX 6 Quad/Dual with: > - i.MX 6Quad/Dual SOC > - NAND or eMMC > - HDMI interface > - LVDS display interface > - Gigabit Ethernet > - USB Host > - CAN > - RS232 > - PCIe > This board also contains an LVDS camera interface and parallel display > interface which are not yet supported. > > phyBAORD-Mira with phyCORE-i.MX 6 DualLight/Solo with: > - i.MX 6DualLight/Solo > - NAND > - HDMI interface > - 100 MBit/s Ethernet > - USB Host > - RS232 > > phyBOARD-Mira with phyCORE-i.MX 6 QuadPlus with: > - i.MX 6QuadPlus SOC > - NAND > - HDMI interface > - LVDS display interface > - Gigabit Ethernet > - USB Host > - CAN > - RS232 > - PCIe > This board also contains an LVDS camera interface and parallel display > interface which are not yet supported. > > The entire series is based on v4.15-rc4. > > Changes since v1: > - Removed unnecessary ipu aliases > - Added unit-address to memory node name > - Fixed eeprom compatible to correct vendor name (atmel instead of cat) > - Fixed rtc compatible to correct vendor name (microcrystal instead of mc) > - Changed pcie regulator to be used with vpcie-supply in &pcie node and > removed regulator-always-on > - Changed pcie reset-gpio polarity to GPIO_ACTIVE_LOW > - Replaced fsl,uart-has-rtscts by uart-has-rtscts > - Fixed typos in defconfig patch > > Changes since v2: > - Fixed typo in patch subject PATCH 4/6 > - Added reviewed by tags on PATCH 4/6 and PATCH 6/6 > > Changes since v3: > - Removed model and compatible from phycore dtsi > - Changed flash compatible to jedec,spi-nor > - Renamed some_green node to som-led-green > - Dropped labels for eeprom, pmic, da9062_wdt and da9062_reg > - Renamed flash label to m25p80 > - Put compatible at beginning of property lists > - Changed copyright year to 2018 > - Added reviewed by tags on PATCH 1/6, 2/6, 3/6 and 5/6 > > Changes since v4: > - Rearranged &m25p80 node in dts files to fit alphabetical order > - Fixed a parenthesis for uniformity in mira dtsi > > Christian Hemp (2): > ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK > ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6 DualLight/Solo > RDK > > Enrico Scholz (1): > ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus > > Stefan Riedmueller (3): > ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM > ARM: dts: imx6: Add initial support for phyBOARD-Mira > ARM: imx_v6_v7_defconfig: Enable Dialog Semiconductor DA9062 driver > > arch/arm/boot/dts/Makefile | 4 + > arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts | 64 ++++ > arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts | 72 ++++ > arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts | 72 ++++ > arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi | 390 ++++++++++++++++++++++ > arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 279 ++++++++++++++++ > arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts | 72 ++++ > arch/arm/configs/imx_v6_v7_defconfig | 4 + > 8 files changed, 957 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts > create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts > create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts > create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi > create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi > create mode 100644 arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts >
On Tue, Jan 09, 2018 at 05:09:54PM +0100, Stefan Riedmueller wrote: > Changes since v4: > - Rearranged &m25p80 node in dts files to fit alphabetical order > - Fixed a parenthesis for uniformity in mira dtsi > > Christian Hemp (2): > ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK > ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6 DualLight/Solo > RDK > > Enrico Scholz (1): > ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus > > Stefan Riedmueller (3): > ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM > ARM: dts: imx6: Add initial support for phyBOARD-Mira Okay, I replaced v4 with this v5. > ARM: imx_v6_v7_defconfig: Enable Dialog Semiconductor DA9062 driver This one still doesn't apply to imx/defconfig. Please rebase and resend. Shawn