| Message ID | 1513940353-6145-1-git-send-email-s.riedmueller@phytec.de |
|---|---|
| Headers | show |
| Series | ARM: dts: Add PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira carrier board support | expand |
Hi Stefan, I am sorry I missed some points during my last review. On Fri, Dec 22, 2017 at 8:59 AM, Stefan Riedmueller <s.riedmueller@phytec.de> wrote: > This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX > 6Quad/Dual or i.MX 6DualLight/Solo. > > Signed-off-by: Christian Hemp <c.hemp@phytec.de> > Signed-off-by: Stefan Christ <s.christ@phytec.de> > Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> > Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> > --- > arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 282 ++++++++++++++++++++++ > 1 file changed, 282 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi > > diff --git a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi > new file mode 100644 > index 0000000..8501ac6 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi > @@ -0,0 +1,282 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2017 PHYTEC Messtechnik GmbH > + * Author: Christian Hemp <c.hemp@phytec.de> > + */ > + > +#include <dt-bindings/gpio/gpio.h> > + > +/ { > + model = "PHYTEC phyCORE-i.MX 6"; > + compatible = "phytec,imx6qdl-pcm058", "fsl,imx6qdl"; fsl,imx6qdl is not a documented compatible. Please remove the model and compatible from the dtsi and put it only in the dts files. > + > + aliases { > + rtc1 = &da9062_rtc; > + rtc2 = &snvs_rtc; > + }; > + > + /* > + * Set the minimum memory size here and > + * let the bootloader set the real size. > + */ > + memory@10000000 { > + device_type = "memory"; > + reg = <0x10000000 0x8000000>; > + }; > + > + gpio_leds_som: somleds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gpioleds_som>; > + > + som_green { > + label = "phycore:green"; > + gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + }; > + }; > +}; > + > +&ecspi1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ecspi1>; > + cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; > + status = "okay"; > + > + flash: flash@0 { > + compatible = "m25p80"; Please check Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt for the proper usage of the SPI NOR compatible. Or you can also check arch/arm/boot/dts/imx6qdl-sabresd.dtsi as reference. With these two changes you can add: Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
On Fri, Dec 22, 2017 at 8:59 AM, Stefan Riedmueller <s.riedmueller@phytec.de> wrote: > This patch adds basic support for PHYTEC phyBOARD-Mira as carrier board > for PHYTEC phyCORE-i.MX 6. > > Signed-off-by: Christian Hemp <c.hemp@phytec.de> > Signed-off-by: Stefan Christ <s.christ@phytec.de> > Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> > Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
On Fri, Dec 22, 2017 at 8:59 AM, Stefan Riedmueller <s.riedmueller@phytec.de> wrote: > From: Christian Hemp <c.hemp@phytec.de> > > Add support for the PHYTEC phyBOARD-Mira Rapid Development Kit with > i.MX 6Quad/Dual with eMMC or NAND. > > Following interfaces are supported: > - Gigabit Ethernet > - USB Host > - CAN > - RS232 > - PCIe > - LVDS > - HDMI > > Signed-off-by: Christian Hemp <c.hemp@phytec.de> > Signed-off-by: Stefan Christ <s.christ@phytec.de> > Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
On Fri, Dec 22, 2017 at 8:59 AM, Stefan Riedmueller <s.riedmueller@phytec.de> wrote: > From: Enrico Scholz <enrico.scholz@sigma-chemnitz.de> > > Add support for the PHYTEC phyBOARD-Mira with i.MX 6QuadPlus with NAND. > It is based on the phyBOARD-Mira with i.MX 6Quad/Dual and supports the > same interfaces. > > Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de> > Signed-off-by: Stefan Lengfeld <s.lengfeld@phytec.de> > Signed-off-by: Christian Hemp <c.hemp@phytec.de> > Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
On Fri, Dec 22, 2017 at 11:59:08AM +0100, Stefan Riedmueller wrote: > This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX > 6Quad/Dual or i.MX 6DualLight/Solo. > > Signed-off-by: Christian Hemp <c.hemp@phytec.de> > Signed-off-by: Stefan Christ <s.christ@phytec.de> > Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> > Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> > --- > arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 282 ++++++++++++++++++++++ > 1 file changed, 282 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi > > diff --git a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi > new file mode 100644 > index 0000000..8501ac6 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi > @@ -0,0 +1,282 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2017 PHYTEC Messtechnik GmbH > + * Author: Christian Hemp <c.hemp@phytec.de> > + */ > + > +#include <dt-bindings/gpio/gpio.h> > + > +/ { > + model = "PHYTEC phyCORE-i.MX 6"; > + compatible = "phytec,imx6qdl-pcm058", "fsl,imx6qdl"; > + > + aliases { > + rtc1 = &da9062_rtc; > + rtc2 = &snvs_rtc; > + }; > + > + /* > + * Set the minimum memory size here and > + * let the bootloader set the real size. > + */ > + memory@10000000 { > + device_type = "memory"; > + reg = <0x10000000 0x8000000>; > + }; > + > + gpio_leds_som: somleds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gpioleds_som>; > + > + som_green { We generally use hyphen rather than underscore in node name. Also I would suggest to have 'led' in the name to tell what the device is, maybe 'led-green'? > + label = "phycore:green"; > + gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + }; > + }; > +}; > + > +&ecspi1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ecspi1>; > + cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; > + status = "okay"; > + > + flash: flash@0 { While it's all good to name the node in a general way, the label can be specific, like: m25p80: flash@0 { ... } Even better, if the label is not really needed, just drop it. > + compatible = "m25p80"; > + spi-max-frequency = <20000000>; > + reg = <0>; > + status = "disabled"; > + }; > +}; > + > +&fec { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_enet>; > + phy-handle = <ðphy>; > + phy-mode = "rgmii"; > + phy-supply = <&vdd_eth_io>; > + phy-reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; > + status = "disabled"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethphy: ethernet-phy@3 { > + reg = <3>; > + txc-skew-ps = <1680>; > + rxc-skew-ps = <1860>; > + }; > + }; > +}; > + > +&gpmi { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gpmi_nand>; > + nand-on-flash-bbt; > + status = "disabled"; > +}; > + > +&i2c3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3>; > + clock-frequency = <400000>; > + status = "okay"; > + > + eeprom: eeprom@50 { Is the label used at all? > + compatible = "atmel,24c32"; > + reg = <0x50>; > + }; > + > + pmic0: pmic@58 { Ditto > + compatible = "dlg,da9062"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pmic>; > + reg = <0x58>; > + interrupt-parent = <&gpio1>; > + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; > + interrupt-controller; > + > + da9062_rtc: rtc { > + compatible = "dlg,da9062-rtc"; > + }; > + > + da9062_wdt: watchdog { Ditto > + compatible = "dlg,da9062-watchdog"; > + }; > + > + da9062_reg: regulators { Ditto Shawn > + vdd_arm: buck1 { > + regulator-name = "vdd_arm"; > + regulator-min-microvolt = <730000>; > + regulator-max-microvolt = <1380000>; > + regulator-always-on; > + }; > + > + vdd_soc: buck2 { > + regulator-name = "vdd_soc"; > + regulator-min-microvolt = <730000>; > + regulator-max-microvolt = <1380000>; > + regulator-always-on; > + }; > + > + vdd_ddr3_1p5: buck3 { > + regulator-name = "vdd_ddr3"; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <1500000>; > + regulator-always-on; > + }; > + > + vdd_eth_1p2: buck4 { > + regulator-name = "vdd_eth"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + }; > + > + vdd_snvs: ldo1 { > + regulator-name = "vdd_snvs"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + regulator-always-on; > + }; > + > + vdd_high: ldo2 { > + regulator-name = "vdd_high"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + regulator-always-on; > + }; > + > + vdd_eth_io: ldo3 { > + regulator-name = "vdd_eth_io"; > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <2500000>; > + }; > + > + vdd_emmc_1p8: ldo4 { > + regulator-name = "vdd_emmc"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + }; > + }; > +}; > + > +®_arm { > + vin-supply = <&vdd_arm>; > +}; > + > +®_pu { > + vin-supply = <&vdd_soc>; > +}; > + > +®_soc { > + vin-supply = <&vdd_soc>; > +}; > + > +&snvs_poweroff { > + status = "okay"; > +}; > + > +&usdhc4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc4>; > + bus-width = <8>; > + non-removable; > + vmmc-supply = <&vdd_emmc_1p8>; > + status = "disabled"; > +}; > + > +&iomuxc { > + pinctrl_enet: enetgrp { > + fsl,pins = < > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 > + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 > + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 > + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 > + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 > + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 > + MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0 > + >; > + }; > + > + pinctrl_gpioleds_som: gpioledssomgrp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 > + >; > + }; > + > + pinctrl_gpmi_nand: gpminandgrp { > + fsl,pins = < > + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 > + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 > + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 > + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 > + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 > + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 > + MX6QDL_PAD_NANDF_CS2__NAND_CE2_B 0xb0b1 > + MX6QDL_PAD_NANDF_CS3__NAND_CE3_B 0xb0b1 > + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 > + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 > + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 > + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 > + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 > + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 > + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 > + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 > + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 > + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 > + MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1 > + >; > + }; > + > + pinctrl_i2c3: i2c3grp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 > + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 > + >; > + }; > + > + pinctrl_ecspi1: ecspi1grp { > + fsl,pins = < > + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 > + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 > + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 > + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b0 > + >; > + }; > + > + pinctrl_pmic: pmicgrp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 > + >; > + }; > + > + pinctrl_usdhc4: usdhc4grp { > + fsl,pins = < > + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 > + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 > + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 > + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 > + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 > + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 > + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059 > + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059 > + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059 > + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059 > + >; > + }; > +}; > -- > 2.7.4 >
On Fri, Dec 22, 2017 at 11:59:09AM +0100, Stefan Riedmueller wrote: > This patch adds basic support for PHYTEC phyBOARD-Mira as carrier board > for PHYTEC phyCORE-i.MX 6. > > Signed-off-by: Christian Hemp <c.hemp@phytec.de> > Signed-off-by: Stefan Christ <s.christ@phytec.de> > Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> > Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> > --- > arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi | 390 +++++++++++++++++++++++++++++ > 1 file changed, 390 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi > > diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi > new file mode 100644 > index 0000000..45d8c0c > --- /dev/null > +++ b/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi > @@ -0,0 +1,390 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2017 PHYTEC Messtechnik GmbH > + * Author: Christian Hemp <c.hemp@phytec.de> > + */ > + > + > +/ { > + aliases { > + rtc0 = &i2c_rtc; > + }; > + > + backlight: backlight { > + compatible = "pwm-backlight"; > + brightness-levels = <0 4 8 16 32 64 128 255>; > + default-brightness-level = <7>; > + power-supply = <®_backlight>; > + pwms = <&pwm1 0 5000000>; > + status = "okay"; > + }; > + > + gpio_leds: leds { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gpioleds>; > + status = "disabled"; > + Generally we do not have newlines in middle of property list. > + compatible = "gpio-leds"; Please put 'compatible' at the beginning of property list and always have 'status' be the end of list. > + > + red { > + label = "phyboard-mira:red"; > + gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; > + }; > + > + green { > + label = "phyboard-mira:green"; > + gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>; > + }; > + > + blue { > + label = "phyboard-mira:blue"; > + gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "mmc0"; > + }; > + }; > + > + reg_backlight: regulator-backlight { > + compatible = "regulator-fixed"; > + regulator-name = "backlight_3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + reg_en_switch: regulator-en-switch { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_en_switch>; > + compatible = "regulator-fixed"; Move the 'compatible' forward. > + regulator-name = "Enable Switch"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + enable-active-high; > + gpio = <&gpio3 4 GPIO_ACTIVE_HIGH>; > + regulator-always-on; > + }; > + > + reg_flexcan1: regulator-flexcan1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_flexcan1_en>; > + compatible = "regulator-fixed"; > + regulator-name = "flexcan1-reg"; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <1500000>; > + gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_panel: regulator-panel { > + compatible = "regulator-fixed"; > + regulator-name = "panel-power-supply"; > + regulator-min-microvolt = <12000000>; > + regulator-max-microvolt = <12000000>; > + regulator-always-on; > + }; > + > + reg_pcie: regulator-pcie { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pcie_reg>; > + compatible = "regulator-fixed"; > + regulator-name = "mPCIe_1V5"; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <1500000>; > + gpio = <&gpio3 0 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_usb_h1_vbus: usb-h1-vbus { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbh1_vbus>; > + compatible = "regulator-fixed"; > + regulator-name = "usb_h1_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpio2 18 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_usbotg_vbus: usbotg-vbus { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg_vbus>; > + compatible = "regulator-fixed"; > + regulator-name = "usb_otg_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + panel { > + compatible = "auo,g104sn02"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_panel_en>; > + power-supply = <®_panel>; > + enable-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; > + Drop the newline. Shawn > + backlight = <&backlight>; > + > + port { > + panel_in: endpoint { > + remote-endpoint = <&lvds0_out>; > + }; > + }; > + }; > +}; > + > +&can1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_flexcan1>; > + xceiver-supply = <®_flexcan1>; > + status = "disabled"; > +}; > + > +&hdmi { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hdmicec>; > + ddc-i2c-bus = <&i2c2>; > + status = "disabled"; > +}; > + > +&i2c1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + clock-frequency = <400000>; > + status = "disabled"; > + > + stmpe: touchctrl@44 { > + compatible = "st,stmpe811"; > + reg = <0x44>; > + interrupt-parent = <&gpio7>; > + interrupts = <12 IRQ_TYPE_NONE>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_stmpe>; > + status = "disabled"; > + > + stmpe_touchscreen { > + compatible = "st,stmpe-ts"; > + st,sample-time = <4>; > + st,mod-12b = <1>; > + st,ref-sel = <0>; > + st,adc-freq = <1>; > + st,ave-ctrl = <1>; > + st,touch-det-delay = <2>; > + st,settling = <2>; > + st,fraction-z = <7>; > + st,i-drive = <1>; > + }; > + }; > + > + i2c_rtc: rtc@68 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_rtc_int>; > + compatible = "microcrystal,rv4162"; > + reg = <0x68>; > + interrupt-parent = <&gpio7>; > + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; > + status = "disabled"; > + }; > +}; > + > +&i2c2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + clock-frequency = <100000>; > + status = "disabled"; > +}; > + > +&ldb { > + status = "okay"; > + > + lvds-channel@0 { > + fsl,data-mapping = "spwg"; > + fsl,data-width = <24>; > + status = "disabled"; > + > + port@4 { > + reg = <4>; > + > + lvds0_out: endpoint { > + remote-endpoint = <&panel_in>; > + }; > + }; > + }; > +}; > + > +&pcie { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pcie>; > + reset-gpio = <&gpio2 25 GPIO_ACTIVE_LOW>; > + vpcie-supply = <®_pcie>; > + status = "disabled"; > +}; > + > +&pwm1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm1>; > + status = "okay"; > +}; > + > +&uart2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2>; > + status = "okay"; > +}; > + > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3>; > + uart-has-rtscts; > + status = "disabled"; > +}; > + > +&usbh1 { > + vbus-supply = <®_usb_h1_vbus>; > + disable-over-current; > + status = "disabled"; > +}; > + > +&usbotg { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg>; > + vbus-supply = <®_usbotg_vbus>; > + disable-over-current; > + status = "disabled"; > +}; > + > +&usdhc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc1>; > + cd-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>; > + no-1-8-v; > + status = "disabled"; > +}; > + > +&iomuxc { > + pinctrl_panel_en: panelen1grp { > + fsl,pins = < > + MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0xb0b1 > + >; > + }; > + > + pinctrl_en_switch: enswitchgrp { > + fsl,pins = < > + MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0xb0b1 > + >; > + }; > + > + pinctrl_flexcan1: flexcan1grp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0 > + MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0 > + >; > + }; > + > + pinctrl_flexcan1_en: flexcan1engrp { > + fsl,pins = < > + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0xb0b1 > + >; > + }; > + > + pinctrl_gpioleds: gpioledsgrp { > + fsl,pins = < > + MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0 > + MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0 > + MX6QDL_PAD_CSI0_DAT6__GPIO5_IO24 0x1b0b0 > + >; > + }; > + > + pinctrl_hdmicec: hdmicecgrp { > + fsl,pins = < > + MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0 > + >; > + }; > + > + pinctrl_i2c2: i2c2grp { > + fsl,pins = < > + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 > + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 > + >; > + }; > + > + pinctrl_i2c1: i2c1grp { > + fsl,pins = < > + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 > + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 > + >; > + }; > + > + pinctrl_pcie: pciegrp { > + fsl,pins = < > + MX6QDL_PAD_EIM_OE__GPIO2_IO25 0xb0b1 > + >; > + }; > + > + pinctrl_pcie_reg: pciereggrp { > + fsl,pins = <MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0xb0b1>; > + }; > + > + pinctrl_pwm1: pwm1grp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1 > + >; > + }; > + > + pinctrl_rtc_int: rtcintgrp { > + fsl,pins = < > + MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b0 > + >; > + }; > + > + pinctrl_stmpe: stmpegrp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 > + >; > + }; > + > + pinctrl_uart2: uart2grp { > + fsl,pins = < > + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 > + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 > + >; > + }; > + > + pinctrl_uart3: uart3grp { > + fsl,pins = < > + MX6QDL_PAD_EIM_EB3__UART3_CTS_B 0x1b0b1 > + MX6QDL_PAD_EIM_D23__UART3_RTS_B 0x1b0b1 > + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 > + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 > + >; > + }; > + > + pinctrl_usbh1_vbus: usbh1vbusgrp { > + fsl,pins = < > + MX6QDL_PAD_EIM_A20__GPIO2_IO18 0xb0b1 > + >; > + }; > + > + pinctrl_usbotg: usbotggrp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 > + >; > + }; > + > + pinctrl_usbotg_vbus: usbotgvbusgrp { > + fsl,pins = < > + MX6QDL_PAD_EIM_A19__GPIO2_IO19 0xb0b1 > + >; > + }; > + > + pinctrl_usdhc1: usdhc1grp { > + fsl,pins = < > + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9 > + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9 > + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 > + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 > + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 > + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 > + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0xb0b1 /* CD */ > + >; > + }; > +}; > -- > 2.7.4 >
On 27.12.2017 03:18, Shawn Guo wrote: > On Fri, Dec 22, 2017 at 11:59:08AM +0100, Stefan Riedmueller wrote: >> This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX >> 6Quad/Dual or i.MX 6DualLight/Solo. >> >> Signed-off-by: Christian Hemp <c.hemp@phytec.de> >> Signed-off-by: Stefan Christ <s.christ@phytec.de> >> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> >> Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> >> --- >> arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 282 ++++++++++++++++++++++ >> 1 file changed, 282 insertions(+) >> create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi >> >> diff --git a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi >> new file mode 100644 >> index 0000000..8501ac6 >> --- /dev/null >> +++ b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi >> @@ -0,0 +1,282 @@ >> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >> +/* >> + * Copyright (C) 2017 PHYTEC Messtechnik GmbH >> + * Author: Christian Hemp <c.hemp@phytec.de> >> + */ >> + >> +#include <dt-bindings/gpio/gpio.h> >> + >> +/ { >> + model = "PHYTEC phyCORE-i.MX 6"; >> + compatible = "phytec,imx6qdl-pcm058", "fsl,imx6qdl"; >> + >> + aliases { >> + rtc1 = &da9062_rtc; >> + rtc2 = &snvs_rtc; >> + }; >> + >> + /* >> + * Set the minimum memory size here and >> + * let the bootloader set the real size. >> + */ >> + memory@10000000 { >> + device_type = "memory"; >> + reg = <0x10000000 0x8000000>; >> + }; >> + >> + gpio_leds_som: somleds { >> + compatible = "gpio-leds"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_gpioleds_som>; >> + >> + som_green { > We generally use hyphen rather than underscore in node name. Also I > would suggest to have 'led' in the name to tell what the device is, > maybe 'led-green'? Hi Shawn, OK. I'll change it to som-led-green. >> + label = "phycore:green"; >> + gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; >> + linux,default-trigger = "heartbeat"; >> + }; >> + }; >> +}; >> + >> +&ecspi1 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_ecspi1>; >> + cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; >> + status = "okay"; >> + >> + flash: flash@0 { > While it's all good to name the node in a general way, the label can be > specific, like: > > m25p80: flash@0 { > ... > } > > Even better, if the label is not really needed, just drop it. We use the label to cover our possible module variants where some can have the flash not populated. We do this by only enabling the required nodes in the dts files. Thats why I would like to keep the label and if possible keep it generic. >> + compatible = "m25p80"; >> + spi-max-frequency = <20000000>; >> + reg = <0>; >> + status = "disabled"; >> + }; >> +}; >> + >> +&fec { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_enet>; >> + phy-handle = <ðphy>; >> + phy-mode = "rgmii"; >> + phy-supply = <&vdd_eth_io>; >> + phy-reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; >> + status = "disabled"; >> + >> + mdio { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + ethphy: ethernet-phy@3 { >> + reg = <3>; >> + txc-skew-ps = <1680>; >> + rxc-skew-ps = <1860>; >> + }; >> + }; >> +}; >> + >> +&gpmi { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_gpmi_nand>; >> + nand-on-flash-bbt; >> + status = "disabled"; >> +}; >> + >> +&i2c3 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c3>; >> + clock-frequency = <400000>; >> + status = "okay"; >> + >> + eeprom: eeprom@50 { > Is the label used at all? Actually it's supposed to, but I forget to take it to the dts file. I would add status = "disabled" here and status = "okay" in the dts files of this patchset if it is okay to keep the label. >> + compatible = "atmel,24c32"; >> + reg = <0x50>; >> + }; >> + >> + pmic0: pmic@58 { > Ditto I'll drop this label. > >> + compatible = "dlg,da9062"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_pmic>; >> + reg = <0x58>; >> + interrupt-parent = <&gpio1>; >> + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; >> + interrupt-controller; >> + >> + da9062_rtc: rtc { >> + compatible = "dlg,da9062-rtc"; >> + }; >> + >> + da9062_wdt: watchdog { > Ditto I'll drop this label. >> + compatible = "dlg,da9062-watchdog"; >> + }; >> + >> + da9062_reg: regulators { > Ditto > > Shawn I'll drop this label. Thanks, Stefan >> + vdd_arm: buck1 { >> + regulator-name = "vdd_arm"; >> + regulator-min-microvolt = <730000>; >> + regulator-max-microvolt = <1380000>; >> + regulator-always-on; >> + }; >> + >> + vdd_soc: buck2 { >> + regulator-name = "vdd_soc"; >> + regulator-min-microvolt = <730000>; >> + regulator-max-microvolt = <1380000>; >> + regulator-always-on; >> + }; >> + >> + vdd_ddr3_1p5: buck3 { >> + regulator-name = "vdd_ddr3"; >> + regulator-min-microvolt = <1500000>; >> + regulator-max-microvolt = <1500000>; >> + regulator-always-on; >> + }; >> + >> + vdd_eth_1p2: buck4 { >> + regulator-name = "vdd_eth"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-always-on; >> + }; >> + >> + vdd_snvs: ldo1 { >> + regulator-name = "vdd_snvs"; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3000000>; >> + regulator-always-on; >> + }; >> + >> + vdd_high: ldo2 { >> + regulator-name = "vdd_high"; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3000000>; >> + regulator-always-on; >> + }; >> + >> + vdd_eth_io: ldo3 { >> + regulator-name = "vdd_eth_io"; >> + regulator-min-microvolt = <2500000>; >> + regulator-max-microvolt = <2500000>; >> + }; >> + >> + vdd_emmc_1p8: ldo4 { >> + regulator-name = "vdd_emmc"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + }; >> + }; >> + }; >> +}; >> + >> +®_arm { >> + vin-supply = <&vdd_arm>; >> +}; >> + >> +®_pu { >> + vin-supply = <&vdd_soc>; >> +}; >> + >> +®_soc { >> + vin-supply = <&vdd_soc>; >> +}; >> + >> +&snvs_poweroff { >> + status = "okay"; >> +}; >> + >> +&usdhc4 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_usdhc4>; >> + bus-width = <8>; >> + non-removable; >> + vmmc-supply = <&vdd_emmc_1p8>; >> + status = "disabled"; >> +}; >> + >> +&iomuxc { >> + pinctrl_enet: enetgrp { >> + fsl,pins = < >> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 >> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 >> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 >> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 >> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 >> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 >> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 >> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 >> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 >> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 >> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 >> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 >> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 >> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 >> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 >> + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 >> + MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0 >> + >; >> + }; >> + >> + pinctrl_gpioleds_som: gpioledssomgrp { >> + fsl,pins = < >> + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 >> + >; >> + }; >> + >> + pinctrl_gpmi_nand: gpminandgrp { >> + fsl,pins = < >> + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 >> + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 >> + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 >> + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 >> + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 >> + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 >> + MX6QDL_PAD_NANDF_CS2__NAND_CE2_B 0xb0b1 >> + MX6QDL_PAD_NANDF_CS3__NAND_CE3_B 0xb0b1 >> + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 >> + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 >> + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 >> + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 >> + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 >> + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 >> + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 >> + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 >> + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 >> + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 >> + MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1 >> + >; >> + }; >> + >> + pinctrl_i2c3: i2c3grp { >> + fsl,pins = < >> + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 >> + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 >> + >; >> + }; >> + >> + pinctrl_ecspi1: ecspi1grp { >> + fsl,pins = < >> + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 >> + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 >> + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 >> + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b0 >> + >; >> + }; >> + >> + pinctrl_pmic: pmicgrp { >> + fsl,pins = < >> + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 >> + >; >> + }; >> + >> + pinctrl_usdhc4: usdhc4grp { >> + fsl,pins = < >> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 >> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 >> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 >> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 >> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 >> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 >> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059 >> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059 >> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059 >> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059 >> + >; >> + }; >> +}; >> -- >> 2.7.4 >>
This patchset adds support for the PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira. Following boards are included: phyBOARD-Mira with phyCORE-i.MX 6 Quad/Dual with: - i.MX 6Quad/Dual SOC - NAND or eMMC - HDMI interface - LVDS display interface - Gigabit Ethernet - USB Host - CAN - RS232 - PCIe This board also contains an LVDS camera interface and parallel display interface which are not yet supported. phyBAORD-Mira with phyCORE-i.MX 6 DualLight/Solo with: - i.MX 6DualLight/Solo - NAND - HDMI interface - 100 MBit/s Ethernet - USB Host - RS232 phyBOARD-Mira with phyCORE-i.MX 6 QuadPlus with: - i.MX 6QuadPlus SOC - NAND - HDMI interface - LVDS display interface - Gigabit Ethernet - USB Host - CAN - RS232 - PCIe This board also contains an LVDS camera interface and parallel display interface which are not yet supported. The entire series is based on v4.15-rc4. Changes since v1: - Removed unnecessary ipu aliases - Added unit-address to memory node name - Fixed eeprom compatible to correct vendor name (atmel instead of cat) - Fixed rtc compatible to correct vendor name (microcrystal instead of mc) - Changed pcie regulator to be used with vpcie-supply in &pcie node and removed regulator-always-on - Changed pcie reset-gpio polarity to GPIO_ACTIVE_LOW - Replaced fsl,uart-has-rtscts by uart-has-rtscts - Fixed typos in defconfig patch Changes since v2: - Fixed typo in patch subject PATCH 4/6 - Added reviewed by tags on PATCH 4/6 and PATCH 6/6 Christian Hemp (2): ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6 DualLight/Solo RDK Enrico Scholz (1): ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus Stefan Riedmueller (3): ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM ARM: dts: imx6: Add initial support for phyBOARD-Mira ARM: imx_v6_v7_defconfig: Enable Dialog Semiconductor DA9062 driver arch/arm/boot/dts/Makefile | 4 + arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts | 64 ++++ arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts | 72 ++++ arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts | 72 ++++ arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi | 390 ++++++++++++++++++++++ arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 282 ++++++++++++++++ arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts | 72 ++++ arch/arm/configs/imx_v6_v7_defconfig | 4 + 8 files changed, 960 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi create mode 100644 arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts