[6/7] phy: Add SATA3 PHY support for Broadcom NSP SoC

This patch adds support for Broadcom NSP SATA3 PHY in existing
Broadcom SATA PHY driver.

Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
---
 drivers/phy/phy-brcm-sata.c | 81 +++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 81 insertions(+)

On 06/16/2016 06:53 AM, Yendapally Reddy Dhananjaya Reddy wrote:
> This patch adds support for Broadcom NSP SATA3 PHY in existing
> Broadcom SATA PHY driver.
> 
> Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>

Acked-by: Florian Fainelli <f.fainelli@gmail.com>

On Thursday 16 June 2016 07:23 PM, Yendapally Reddy Dhananjaya Reddy wrote:
> This patch adds support for Broadcom NSP SATA3 PHY in existing
> Broadcom SATA PHY driver.
> 
> Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>

Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
> ---
>  drivers/phy/phy-brcm-sata.c | 81 +++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 81 insertions(+)
> 
> diff --git a/drivers/phy/phy-brcm-sata.c b/drivers/phy/phy-brcm-sata.c
> index 6c4c5cb..18d6626 100644
> --- a/drivers/phy/phy-brcm-sata.c
> +++ b/drivers/phy/phy-brcm-sata.c
> @@ -45,6 +45,7 @@ enum brcm_sata_phy_version {
>  	BRCM_SATA_PHY_STB_28NM,
>  	BRCM_SATA_PHY_STB_40NM,
>  	BRCM_SATA_PHY_IPROC_NS2,
> +	BRCM_SATA_PHY_IPROC_NSP,
>  };
>  
>  struct brcm_sata_port {
> @@ -73,6 +74,13 @@ enum sata_phy_regs {
>  
>  	PLL_REG_BANK_0				= 0x050,
>  	PLL_REG_BANK_0_PLLCONTROL_0		= 0x81,
> +	PLLCONTROL_0_FREQ_DET_RESTART		= BIT(13),
> +	PLLCONTROL_0_FREQ_MONITOR		= BIT(12),
> +	PLLCONTROL_0_SEQ_START			= BIT(15),
> +	PLL_CAP_CONTROL				= 0x85,
> +	PLL_ACTRL2				= 0x8b,
> +	PLL_ACTRL2_SELDIV_MASK			= 0x1f,
> +	PLL_ACTRL2_SELDIV_SHIFT			= 9,
>  
>  	PLL1_REG_BANK				= 0x060,
>  	PLL1_ACTRL2				= 0x82,
> @@ -80,6 +88,7 @@ enum sata_phy_regs {
>  	PLL1_ACTRL4				= 0x84,
>  
>  	OOB_REG_BANK				= 0x150,
> +	OOB1_REG_BANK				= 0x160,
>  	OOB_CTRL1				= 0x80,
>  	OOB_CTRL1_BURST_MAX_MASK		= 0xf,
>  	OOB_CTRL1_BURST_MAX_SHIFT		= 12,
> @@ -271,6 +280,73 @@ static int brcm_ns2_sata_init(struct brcm_sata_port *port)
>  	return 0;
>  }
>  
> +static int brcm_nsp_sata_init(struct brcm_sata_port *port)
> +{
> +	struct brcm_sata_phy *priv = port->phy_priv;
> +	struct device *dev = port->phy_priv->dev;
> +	void __iomem *base = priv->phy_base;
> +	unsigned int oob_bank;
> +	unsigned int val, try;
> +
> +	/* Configure OOB control */
> +	if (port->portnum == 0)
> +		oob_bank = OOB_REG_BANK;
> +	else if (port->portnum == 1)
> +		oob_bank = OOB1_REG_BANK;
> +	else
> +		return -EINVAL;
> +
> +	val = 0x0;
> +	val |= (0x0f << OOB_CTRL1_BURST_MAX_SHIFT);
> +	val |= (0x06 << OOB_CTRL1_BURST_MIN_SHIFT);
> +	val |= (0x0f << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT);
> +	val |= (0x06 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT);
> +	brcm_sata_phy_wr(base, oob_bank, OOB_CTRL1, 0x0, val);
> +
> +	val = 0x0;
> +	val |= (0x2e << OOB_CTRL2_RESET_IDLE_MAX_SHIFT);
> +	val |= (0x02 << OOB_CTRL2_BURST_CNT_SHIFT);
> +	val |= (0x16 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT);
> +	brcm_sata_phy_wr(base, oob_bank, OOB_CTRL2, 0x0, val);
> +
> +
> +	brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_ACTRL2,
> +		~(PLL_ACTRL2_SELDIV_MASK << PLL_ACTRL2_SELDIV_SHIFT),
> +		0x0c << PLL_ACTRL2_SELDIV_SHIFT);
> +
> +	brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_CAP_CONTROL,
> +						0xff0, 0x4f0);
> +
> +	val = PLLCONTROL_0_FREQ_DET_RESTART | PLLCONTROL_0_FREQ_MONITOR;
> +	brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
> +								~val, val);
> +	val = PLLCONTROL_0_SEQ_START;
> +	brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
> +								~val, 0);
> +	mdelay(10);
> +	brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
> +								~val, val);
> +
> +	/* Wait for pll_seq_done bit */
> +	try = 50;
> +	while (try--) {
> +		val = brcm_sata_phy_rd(base, BLOCK0_REG_BANK,
> +					BLOCK0_XGXSSTATUS);
> +		if (val & BLOCK0_XGXSSTATUS_PLL_LOCK)
> +			break;
> +		msleep(20);
> +	}
> +	if (!try) {
> +		/* PLL did not lock; give up */
> +		dev_err(dev, "port%d PLL did not lock\n", port->portnum);
> +		return -ETIMEDOUT;
> +	}
> +
> +	dev_dbg(dev, "port%d initialized\n", port->portnum);
> +
> +	return 0;
> +}
> +
>  static int brcm_sata_phy_init(struct phy *phy)
>  {
>  	int rc;
> @@ -284,6 +360,9 @@ static int brcm_sata_phy_init(struct phy *phy)
>  	case BRCM_SATA_PHY_IPROC_NS2:
>  		rc = brcm_ns2_sata_init(port);
>  		break;
> +	case BRCM_SATA_PHY_IPROC_NSP:
> +		rc = brcm_nsp_sata_init(port);
> +		break;
>  	default:
>  		rc = -ENODEV;
>  	};
> @@ -303,6 +382,8 @@ static const struct of_device_id brcm_sata_phy_of_match[] = {
>  	  .data = (void *)BRCM_SATA_PHY_STB_40NM },
>  	{ .compatible	= "brcm,iproc-ns2-sata-phy",
>  	  .data = (void *)BRCM_SATA_PHY_IPROC_NS2 },
> +	{ .compatible = "brcm,iproc-nsp-sata-phy",
> +	  .data = (void *)BRCM_SATA_PHY_IPROC_NSP },
>  	{},
>  };
>  MODULE_DEVICE_TABLE(of, brcm_sata_phy_of_match);
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html