@@ -471,6 +471,7 @@ config I2C_DESIGNWARE_CORE
config I2C_DESIGNWARE_PLATFORM
tristate "Synopsys DesignWare Platform"
select I2C_DESIGNWARE_CORE
+ select I2C_DESIGNWARE_SLAVE
depends on (ACPI && COMMON_CLK) || !ACPI
help
If you say yes to this option, support will be included for the
@@ -228,6 +228,7 @@
* @disable: function to disable the controller
* @disable_int: function to disable all interrupts
* @init: function to initialize the I2C hardware
+ * @mode: operation mode - DW_IC_MASTER or DW_IC_SLAVE
*
* HCNT and LCNT parameters can be used if the platform knows more accurate
* values than the one computed based only on the input clock frequency.
@@ -282,6 +283,7 @@ struct dw_i2c_dev {
void (*disable)(struct dw_i2c_dev *dev);
void (*disable_int)(struct dw_i2c_dev *dev);
int (*init)(struct dw_i2c_dev *dev);
+ int mode;
};
#define ACCESS_SWAP 0x00000001
@@ -1,5 +1,5 @@
/*
- * Synopsys DesignWare I2C adapter driver (master only).
+ * Synopsys DesignWare I2C adapter driver.
*
* Based on the TI DAVINCI I2C adapter driver.
*
@@ -174,9 +174,13 @@ static inline int dw_i2c_acpi_configure(struct platform_device *pdev)
static void i2c_dw_configure_master(struct dw_i2c_dev *dev)
{
+ dev->functionality = I2C_FUNC_10BIT_ADDR | DW_IC_DEFAULT_FUNCTIONALITY;
+
dev->master_cfg = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE |
DW_IC_CON_RESTART_EN;
+ dev->mode = DW_IC_MASTER;
+
switch (dev->clk_freq) {
case 100000:
dev->master_cfg |= DW_IC_CON_SPEED_STD;
@@ -189,6 +193,28 @@ static void i2c_dw_configure_master(struct dw_i2c_dev *dev)
}
}
+static void i2c_dw_configure_slave(struct dw_i2c_dev *dev)
+{
+ dev->functionality = I2C_FUNC_SLAVE | DW_IC_DEFAULT_FUNCTIONALITY;
+
+ dev->slave_cfg = DW_IC_CON_RX_FIFO_FULL_HLD_CTRL |
+ DW_IC_CON_RESTART_EN | DW_IC_CON_STOP_DET_IFADDRESSED |
+ DW_IC_CON_SPEED_FAST;
+
+ dev->mode = DW_IC_SLAVE;
+
+ switch (dev->clk_freq) {
+ case 100000:
+ dev->slave_cfg |= DW_IC_CON_SPEED_STD;
+ break;
+ case 3400000:
+ dev->slave_cfg |= DW_IC_CON_SPEED_HIGH;
+ break;
+ default:
+ dev->slave_cfg |= DW_IC_CON_SPEED_FAST;
+ }
+}
+
static int i2c_dw_plat_prepare_clk(struct dw_i2c_dev *i_dev, bool prepare)
{
if (IS_ERR(i_dev->clk))
@@ -302,9 +328,10 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
if (ret)
goto exit_reset;
- dev->functionality = I2C_FUNC_10BIT_ADDR | DW_IC_DEFAULT_FUNCTIONALITY;
-
- i2c_dw_configure_master(dev);
+ if (i2c_detect_slave_mode(&pdev->dev))
+ i2c_dw_configure_slave(dev);
+ else
+ i2c_dw_configure_master(dev);
dev->clk = devm_clk_get(&pdev->dev, NULL);
if (!i2c_dw_plat_prepare_clk(dev, true)) {
@@ -333,7 +360,11 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
pm_runtime_enable(&pdev->dev);
}
- ret = i2c_dw_probe(dev);
+ if (dev->mode == DW_IC_SLAVE)
+ ret = i2c_dw_probe_slave(dev);
+ else
+ ret = i2c_dw_probe(dev);
+
if (ret)
goto exit_probe;
- Slave mode selected in platform module if the support is detected in the DT. Signed-off-by: Luis Oliveira <lolivei@synopsys.com> --- v9-v10 - Removed "default y" from Kconfig because it was not needed (only for tests) drivers/i2c/busses/Kconfig | 1 + drivers/i2c/busses/i2c-designware-core.h | 2 ++ drivers/i2c/busses/i2c-designware-platdrv.c | 41 +++++++++++++++++++++++++---- 3 files changed, 39 insertions(+), 5 deletions(-)