[v2,3/3] dt-bindings:iio:gyro:invensense,mpu3050: txt to yaml format conversion.

From: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Very similar to the mpu6050 binding.
Only unusual element is the i2c-gate section.
Example tweaked a little to include a real device behind the gate.

As Rob Herring suggested, dropped use of explicit i2c-gate yaml
binding in favour of just using the i2c-controller.yaml binding
directly.

Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201031181801.742585-4-jic23@kernel.org
---
 .../iio/gyroscope/invensense,mpu3050.txt      | 45 ------------
 .../iio/gyroscope/invensense,mpu3050.yaml     | 70 +++++++++++++++++++
 2 files changed, 70 insertions(+), 45 deletions(-)

On Sat, 28 Nov 2020 17:33:43 +0000
Jonathan Cameron <jic23@kernel.org> wrote:

> From: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> 
> Very similar to the mpu6050 binding.
> Only unusual element is the i2c-gate section.
> Example tweaked a little to include a real device behind the gate.
> 
> As Rob Herring suggested, dropped use of explicit i2c-gate yaml
> binding in favour of just using the i2c-controller.yaml binding
> directly.
> 
> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Reviewed-by: Rob Herring <robh@kernel.org>
> Link: https://lore.kernel.org/r/20201031181801.742585-4-jic23@kernel.org
Applied.

Thanks,

Jonathan

> ---
>  .../iio/gyroscope/invensense,mpu3050.txt      | 45 ------------
>  .../iio/gyroscope/invensense,mpu3050.yaml     | 70 +++++++++++++++++++
>  2 files changed, 70 insertions(+), 45 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt
> deleted file mode 100644
> index 233fe207aded..000000000000
> --- a/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt
> +++ /dev/null
> @@ -1,45 +0,0 @@
> -Invensense MPU-3050 Gyroscope device tree bindings
> -
> -Required properties:
> -  - compatible : should be "invensense,mpu3050"
> -  - reg : the I2C address of the sensor
> -
> -Optional properties:
> -  - interrupts : interrupt mapping for the trigger interrupt from the
> -    internal oscillator. The following IRQ modes are supported:
> -    IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, IRQ_TYPE_LEVEL_HIGH and
> -    IRQ_TYPE_LEVEL_LOW. The driver should detect and configure the hardware
> -    for the desired interrupt type.
> -  - vdd-supply : supply regulator for the main power voltage.
> -  - vlogic-supply : supply regulator for the signal voltage.
> -  - mount-matrix : see iio/mount-matrix.txt
> -
> -Optional subnodes:
> -  - The MPU-3050 will pass through and forward the I2C signals from the
> -    incoming I2C bus, alternatively drive traffic to a slave device (usually
> -    an accelerometer) on its own initiative. Therefore is supports a subnode
> -    i2c gate node. For details see: i2c/i2c-gate.txt
> -
> -Example:
> -
> -mpu3050@68 {
> -	compatible = "invensense,mpu3050";
> -	reg = <0x68>;
> -	interrupt-parent = <&foo>;
> -	interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
> -	vdd-supply = <&bar>;
> -	vlogic-supply = <&baz>;
> -
> -	/* External I2C interface */
> -	i2c-gate {
> -		#address-cells = <1>;
> -		#size-cells = <0>;
> -
> -		fnord@18 {
> -			compatible = "fnord";
> -			reg = <0x18>;
> -			interrupt-parent = <&foo>;
> -			interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
> -		};
> -	};
> -};
> diff --git a/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.yaml b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.yaml
> new file mode 100644
> index 000000000000..7e2accc3d5ce
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.yaml
> @@ -0,0 +1,70 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/gyroscope/invensense,mpu3050.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Invensense MPU-3050 Gyroscope
> +
> +maintainers:
> +  - Linus Walleij <linus.walleij@linaro.org>
> +
> +properties:
> +  compatible:
> +    const: invensense,mpu3050
> +
> +  reg:
> +    maxItems: 1
> +
> +  vdd-supply: true
> +
> +  vlogic-supply: true
> +
> +  interrupts:
> +    minItems: 1
> +    description:
> +      Interrupt mapping for the trigger interrupt from the internal oscillator.
> +
> +  mount-matrix: true
> +
> +  i2c-gate:
> +    $ref: /schemas/i2c/i2c-controller.yaml
> +    unevaluatedProperties: false
> +    description: |
> +      The MPU-3050 will pass through and forward the I2C signals from the
> +      incoming I2C bus, alternatively drive traffic to a slave device (usually
> +      an accelerometer) on its own initiative. Therefore is supports an
> +      i2c-gate subnode.
> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +        gyroscope@68 {
> +            compatible = "invensense,mpu3050";
> +            reg = <0x68>;
> +            interrupt-parent = <&foo>;
> +            interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
> +            vdd-supply = <&bar>;
> +            vlogic-supply = <&baz>;
> +
> +            i2c-gate {
> +                #address-cells = <1>;
> +                #size-cells = <0>;
> +
> +                magnetometer@c {
> +                    compatible = "ak,ak8975";
> +                    reg = <0x0c>;
> +                };
> +            };
> +        };
> +    };
> +...