diff mbox series

[3/5] dt-bindings: at24: fix formatting and style

Message ID 20171221130830.16813-4-brgl@bgdev.pl
State Superseded
Headers show
Series eeprom: at24: device tree support fixes | expand

Commit Message

Bartosz Golaszewski Dec. 21, 2017, 1:08 p.m. UTC 
Make formatting and style consistent for the entire document.

This patch doesn't change the content of the binding.

Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
---
 Documentation/devicetree/bindings/eeprom/at24.txt | 24 +++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

Comments

Javier Martinez Canillas Dec. 21, 2017, 1:21 p.m. UTC | #1 
On Thu, Dec 21, 2017 at 2:08 PM, Bartosz Golaszewski <brgl@bgdev.pl> wrote:
> Make formatting and style consistent for the entire document.
>
> This patch doesn't change the content of the binding.
>
> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
> ---

Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>

Best regards,
Javier
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/eeprom/at24.txt b/Documentation/devicetree/bindings/eeprom/at24.txt
index 0322db43c8a4..8a6b960ddeee 100644
--- a/Documentation/devicetree/bindings/eeprom/at24.txt
+++ b/Documentation/devicetree/bindings/eeprom/at24.txt
@@ -2,7 +2,7 @@  EEPROMs (I2C)
 
 Required properties:
 
-  - compatible: must be one of the following:
+  - compatible: Must be one of the following:
 
         "atmel,24c00",
         "atmel,24c01",
@@ -32,23 +32,23 @@  Required properties:
   Also: matching by device type alone - while still supported due to
   implementation details in I2C core - is deprecated as well.
 
-  - reg : the I2C address of the EEPROM
+  - reg: The I2C address of the EEPROM.
 
 Optional properties:
 
-  - pagesize : the length of the pagesize for writing. Please consult the
-               manual of your device, that value varies a lot. A wrong value
-	       may result in data loss! If not specified, a safety value of
-	       '1' is used which will be very slow.
+  - pagesize: The length of the pagesize for writing. Please consult the
+              manual of your device, that value varies a lot. A wrong value
+              may result in data loss! If not specified, a safety value of
+              '1' is used which will be very slow.
 
-  - read-only: this parameterless property disables writes to the eeprom
+  - read-only: This parameterless property disables writes to the eeprom.
 
-  - size: total eeprom size in bytes
+  - size: Total eeprom size in bytes.
 
-  - no-read-rollover:
-			This parameterless property indicates that the multi-address
-			eeprom does not automatically roll over reads to the next
-			slave address. Please consult the manual of your device.
+  - no-read-rollover: This parameterless property indicates that the
+                      multi-address eeprom does not automatically roll over
+                      reads to the next slave address. Please consult the
+                      manual of your device.
 
   - wp-gpios: GPIO to which the write-protect pin of the chip is connected.