| Message ID | 1535589198-16733-1-git-send-email-ajayg@nvidia.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [v3,1/2] i2c: buses: add i2c bus driver for NVIDIA GPU | expand |
On Thu, Aug 30, 2018 at 3:35 AM <ajaykuee@gmail.com> wrote: > > From: Ajay Gupta <ajayg@nvidia.com> > > Latest NVIDIA GPU card has USB Type-C interface. There is a > Type-C controller which can be accessed over I2C. > > This driver adds I2C bus driver to communicate with Type-C controller. > I2C client driver will be part of USB Type-C UCSI driver. > Some small comments below, after addressing them Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> > Signed-off-by: Ajay Gupta <ajayg@nvidia.com> > --- > Changes from v1 -> v2 > None > Changes from v2 -> v3 > Fixed review comments from Andy and Thierry > Rename i2c-gpu.c -> i2c-nvidia-gpu.c > > Documentation/i2c/busses/i2c-nvidia-gpu | 18 ++ > MAINTAINERS | 7 + > drivers/i2c/busses/Kconfig | 9 + > drivers/i2c/busses/Makefile | 1 + > drivers/i2c/busses/i2c-nvidia-gpu.c | 389 ++++++++++++++++++++++++++++++++ > 5 files changed, 424 insertions(+) > create mode 100644 Documentation/i2c/busses/i2c-nvidia-gpu > create mode 100644 drivers/i2c/busses/i2c-nvidia-gpu.c > > diff --git a/Documentation/i2c/busses/i2c-nvidia-gpu b/Documentation/i2c/busses/i2c-nvidia-gpu > new file mode 100644 > index 0000000..31884d2 > --- /dev/null > +++ b/Documentation/i2c/busses/i2c-nvidia-gpu > @@ -0,0 +1,18 @@ > +Kernel driver i2c-nvidia-gpu > + > +Datasheet: not publicly available. > + > +Authors: > + Ajay Gupta <ajayg@nvidia.com> > + > +Description > +----------- > + > +i2c-nvidia-gpu is a driver for I2C controller included in NVIDIA Turing > +and later GPUs and it is used to communicate with Type-C controller on GPUs. > + > +If your 'lspci -v' listing shows something like the following, > + > +01:00.3 Serial bus controller [0c80]: NVIDIA Corporation Device 1ad9 (rev a1) > + > +then this driver should support the I2C controller of your GPU. > diff --git a/MAINTAINERS b/MAINTAINERS > index 9ad052a..2d1c5a1 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -6797,6 +6797,13 @@ L: linux-acpi@vger.kernel.org > S: Maintained > F: drivers/i2c/i2c-core-acpi.c > > +I2C CONTROLLER DRIVER FOR NVIDIA GPU > +M: Ajay Gupta <ajayg@nvidia.com> > +L: linux-i2c@vger.kernel.org > +S: Maintained > +F: Documentation/i2c/busses/i2c-nvidia-gpu > +F: drivers/i2c/busses/i2c-nvidia-gpu.c > + > I2C MUXES > M: Peter Rosin <peda@axentia.se> > L: linux-i2c@vger.kernel.org > diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig > index 451d4ae..eed827b 100644 > --- a/drivers/i2c/busses/Kconfig > +++ b/drivers/i2c/busses/Kconfig > @@ -224,6 +224,15 @@ config I2C_NFORCE2_S4985 > This driver can also be built as a module. If so, the module > will be called i2c-nforce2-s4985. > > +config I2C_NVIDIA_GPU > + tristate "NVIDIA GPU I2C controller" > + depends on PCI > + help > + If you say yes to this option, support will be included for the > + NVIDIA GPU I2C controller which is used to communicate with the GPU's > + Type-C controller. This driver can also be built as a module called > + i2c-nvidia-gpu. > + > config I2C_SIS5595 > tristate "SiS 5595" > depends on PCI > diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile > index 18b26af..d499813 100644 > --- a/drivers/i2c/busses/Makefile > +++ b/drivers/i2c/busses/Makefile > @@ -140,5 +140,6 @@ obj-$(CONFIG_I2C_SIBYTE) += i2c-sibyte.o > obj-$(CONFIG_I2C_XGENE_SLIMPRO) += i2c-xgene-slimpro.o > obj-$(CONFIG_SCx200_ACB) += scx200_acb.o > obj-$(CONFIG_I2C_FSI) += i2c-fsi.o > +obj-$(CONFIG_I2C_NVIDIA_GPU) += i2c-nvidia-gpu.o > > ccflags-$(CONFIG_I2C_DEBUG_BUS) := -DDEBUG > diff --git a/drivers/i2c/busses/i2c-nvidia-gpu.c b/drivers/i2c/busses/i2c-nvidia-gpu.c > new file mode 100644 > index 0000000..fa01187 > --- /dev/null > +++ b/drivers/i2c/busses/i2c-nvidia-gpu.c > @@ -0,0 +1,389 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Nvidia GPU I2C controller Driver > + * > + * Copyright (C) 2018 NVIDIA Corporation. All rights reserved. > + * Author: Ajay Gupta <ajayg@nvidia.com> > + * Redundant line. > + */ > +#include <asm/unaligned.h> This should go after linux/* ones... > +#include <linux/delay.h> > +#include <linux/i2c.h> > +#include <linux/interrupt.h> > +#include <linux/module.h> > +#include <linux/pci.h> > +#include <linux/platform_device.h> > +#include <linux/pm.h> > +#include <linux/pm_runtime.h> > + ...here. > +/* I2C definitions */ > +#define I2C_MST_CNTL 0x0 > +#define I2C_MST_CNTL_GEN_START BIT(0) > +#define I2C_MST_CNTL_GEN_STOP BIT(1) > +#define I2C_MST_CNTL_CMD_NONE (0 << 2) > +#define I2C_MST_CNTL_CMD_READ (1 << 2) > +#define I2C_MST_CNTL_CMD_WRITE (2 << 2) > +#define I2C_MST_CNTL_GEN_RAB BIT(4) > +#define I2C_MST_CNTL_BURST_SIZE_SHIFT (6) Redundant parens > +#define I2C_MST_CNTL_GEN_NACK BIT(28) > +#define I2C_MST_CNTL_STATUS (3 << 29) > +#define I2C_MST_CNTL_STATUS_OKAY (0 << 29) > +#define I2C_MST_CNTL_STATUS_NO_ACK (1 << 29) > +#define I2C_MST_CNTL_STATUS_TIMEOUT (2 << 29) > +#define I2C_MST_CNTL_STATUS_BUS_BUSY (3 << 29) > +#define I2C_MST_CNTL_CYCLE_TRIGGER BIT(31) > + > +#define I2C_MST_ADDR 0x04 > +#define I2C_MST_ADDR_DAB 0 > + > +#define I2C_MST_I2C0_TIMING 0x08 > +#define I2C_MST_I2C0_TIMING_SCL_PERIOD_100KHZ 0x10e > +#define I2C_MST_I2C0_TIMING_TIMEOUT_CLK_CNT 16 > +#define I2C_MST_I2C0_TIMING_TIMEOUT_CLK_CNT_MAX 255 > +#define I2C_MST_I2C0_TIMING_TIMEOUT_CHECK BIT(24) > + > +#define I2C_MST_DATA 0x0c > + > +#define I2C_MST_HYBRID_PADCTL 0x20 > +#define I2C_MST_HYBRID_PADCTL_MODE_I2C BIT(0) > +#define I2C_MST_HYBRID_PADCTL_I2C_SCL_INPUT_RCV BIT(14) > +#define I2C_MST_HYBRID_PADCTL_I2C_SDA_INPUT_RCV BIT(15) > + > +struct gpu_i2c_dev { > + struct pci_dev *pci_dev; This should be a good argument why you are keeping struct pci_dev instead of struct device. > + void __iomem *regs; > + struct i2c_adapter adapter; > + struct i2c_client *client; > + struct mutex mutex; /* to sync read/write */ > + bool do_start; > +}; > + > +static void enable_i2c_bus(struct gpu_i2c_dev *i2cd) > +{ > + u32 val; > + > + /* enable I2C */ > + val = readl(i2cd->regs + I2C_MST_HYBRID_PADCTL); > + val |= I2C_MST_HYBRID_PADCTL_MODE_I2C | > + I2C_MST_HYBRID_PADCTL_I2C_SCL_INPUT_RCV | > + I2C_MST_HYBRID_PADCTL_I2C_SDA_INPUT_RCV; > + writel(val, i2cd->regs + I2C_MST_HYBRID_PADCTL); > + > + /* enable 100KHZ mode */ > + val = I2C_MST_I2C0_TIMING_SCL_PERIOD_100KHZ; > + val |= (I2C_MST_I2C0_TIMING_TIMEOUT_CLK_CNT_MAX > + << I2C_MST_I2C0_TIMING_TIMEOUT_CLK_CNT); > + val |= I2C_MST_I2C0_TIMING_TIMEOUT_CHECK; > + writel(val, i2cd->regs + I2C_MST_I2C0_TIMING); > +} > + > +static int i2c_check_status(struct gpu_i2c_dev *i2cd) > +{ > + unsigned long target = jiffies + msecs_to_jiffies(1000); > + int status = -EIO; You can get rid of this variable by returning in place. > + u32 val; > + > + do { > + val = readl(i2cd->regs + I2C_MST_CNTL); > + if ((val & I2C_MST_CNTL_CYCLE_TRIGGER) != > + I2C_MST_CNTL_CYCLE_TRIGGER) > + break; > + if ((val & I2C_MST_CNTL_STATUS) != > + I2C_MST_CNTL_STATUS_BUS_BUSY) > + break; > + usleep_range(1000, 2000); > + } while (time_is_after_jiffies(target)); > + > + if (time_is_before_jiffies(target)) > + return status; > + > + val = readl(i2cd->regs + I2C_MST_CNTL); > + switch (val & I2C_MST_CNTL_STATUS) { > + case I2C_MST_CNTL_STATUS_OKAY: > + status = 0; > + break; > + case I2C_MST_CNTL_STATUS_NO_ACK: > + status = -EIO; > + break; > + case I2C_MST_CNTL_STATUS_TIMEOUT: > + status = -ETIME; > + break; > + case I2C_MST_CNTL_STATUS_BUS_BUSY: > + status = -EBUSY; > + break; > + default: > + break; > + } > + return status; > +} > + > +static int i2c_read(struct gpu_i2c_dev *i2cd, u8 *data, u16 len) > +{ > + int status; > + u32 val = 0; > + > + val |= I2C_MST_CNTL_GEN_START | I2C_MST_CNTL_GEN_STOP | > + I2C_MST_CNTL_CMD_READ | (len << I2C_MST_CNTL_BURST_SIZE_SHIFT) | > + I2C_MST_CNTL_CYCLE_TRIGGER | I2C_MST_CNTL_GEN_NACK; > + val &= ~I2C_MST_CNTL_GEN_RAB; > + writel(val, i2cd->regs + I2C_MST_CNTL); > + > + status = i2c_check_status(i2cd); > + if (status < 0) > + return status; > + > + val = readl(i2cd->regs + I2C_MST_DATA); > + switch (len) { > + case 1: > + data[0] = val; > + break; > + case 2: > + put_unaligned_be16(val, data); > + break; > + case 3: > + put_unaligned_be16(val >> 8, data); > + data[2] = val; > + break; > + case 4: > + put_unaligned_be32(val, data); > + break; > + default: > + break; > + } > + return status; > +} > + > +static int i2c_start(struct gpu_i2c_dev *i2cd, u16 addr) > +{ > + u32 val; > + > + val = addr << I2C_MST_ADDR_DAB; > + writel(val, i2cd->regs + I2C_MST_ADDR); > + > + val = I2C_MST_CNTL_GEN_START | I2C_MST_CNTL_CMD_NONE | > + I2C_MST_CNTL_GEN_NACK; > + val &= ~(I2C_MST_CNTL_GEN_STOP | I2C_MST_CNTL_GEN_RAB); > + writel(val, i2cd->regs + I2C_MST_CNTL); > + > + return i2c_check_status(i2cd); > +} > + > +static int i2c_stop(struct gpu_i2c_dev *i2cd) > +{ > + u32 val; > + > + val = I2C_MST_CNTL_GEN_STOP | I2C_MST_CNTL_CMD_NONE | > + I2C_MST_CNTL_GEN_NACK; > + val &= ~(I2C_MST_CNTL_GEN_START | I2C_MST_CNTL_GEN_RAB); > + writel(val, i2cd->regs + I2C_MST_CNTL); > + > + return i2c_check_status(i2cd); > +} > + > +static int i2c_write(struct gpu_i2c_dev *i2cd, u8 data) > +{ > + u32 val; > + > + writel(data, i2cd->regs + I2C_MST_DATA); > + > + val = I2C_MST_CNTL_CMD_WRITE | (1 << I2C_MST_CNTL_BURST_SIZE_SHIFT) | > + I2C_MST_CNTL_GEN_NACK; > + val &= ~(I2C_MST_CNTL_GEN_START | I2C_MST_CNTL_GEN_STOP > + | I2C_MST_CNTL_GEN_RAB); > + writel(val, i2cd->regs + I2C_MST_CNTL); > + > + return i2c_check_status(i2cd); > +} > + > +static int gpu_i2c_master_xfer(struct i2c_adapter *adap, > + struct i2c_msg *msgs, int num) > +{ > + struct gpu_i2c_dev *i2cd = i2c_get_adapdata(adap); > + struct device *dev = &i2cd->pci_dev->dev; > + int sts; Btw, be consistent with names, status looks slightly better. > + int i, j; > + > + mutex_lock(&i2cd->mutex); > + for (i = 0; i < num; i++) { > + if (msgs[i].flags & I2C_M_RD) { > + sts = i2c_read(i2cd, msgs[i].buf, msgs[i].len); > + if (sts < 0) { > + dev_err(dev, "i2c_read error %x", sts); > + break; > + } > + i2cd->do_start = true; > + } else if (msgs[i].flags & I2C_M_STOP) { > + sts = i2c_stop(i2cd); > + if (sts < 0) { > + dev_err(dev, "i2c_stop error %x", sts); > + goto unlock; > + } > + i2cd->do_start = true; > + } else { > + if (i2cd->do_start) { > + sts = i2c_start(i2cd, msgs[i].addr); > + if (sts < 0) { > + dev_err(dev, "i2c_start error %x", sts); > + goto unlock; > + } > + sts = i2c_write(i2cd, msgs[i].addr << 1); > + if (sts < 0) { > + dev_err(dev, "i2c_write error %x", sts); > + goto stop; > + } > + i2cd->do_start = false; > + } > + for (j = 0; j < msgs[i].len; j++) { > + sts = i2c_write(i2cd, *(msgs[i].buf + j)); > + if (sts < 0) { > + dev_err(dev, "i2c_write error %x", sts); > + goto stop; > + } > + } > + } > + } > + goto unlock; > +stop: > + sts = i2c_stop(i2cd); > + if (sts < 0) > + dev_err(dev, "i2c_stop error %x", sts); > +unlock: > + mutex_unlock(&i2cd->mutex); > + return i; > +} > + > +static u32 gpu_i2c_functionality(struct i2c_adapter *adap) > +{ > + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; > +} > + > +static const struct i2c_algorithm gpu_i2c_algorithm = { > + .master_xfer = gpu_i2c_master_xfer, > + .functionality = gpu_i2c_functionality, > +}; > + > +#define PCI_CLASS_SERIAL_UNKNOWN 0x0c80 > +static const struct pci_device_id gpu_i2c_ids[] = { > + { PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, > + PCI_CLASS_SERIAL_UNKNOWN << 8, 0xffffff00}, > + { } > +}; I'm really in doubt how it's supposed to be enumerated without conflicts or shadowing other hardware. Explain in the comments, please. > +MODULE_DEVICE_TABLE(pci, gpu_i2c_ids); > + > +static int gpu_i2c_probe(struct pci_dev *dev, const struct pci_device_id *id) > +{ > + struct i2c_board_info gpu_i2c_ucsi_board_info = { > + I2C_BOARD_INFO("ccgx-ucsi", 0x8) > + }; Can't you rather put this as static const which is provided in driver_data above (based on enumeration) and use here something like static const struct i2c_board_info gpu_ccgx_ucsi = { I2C_BOARD_INFO(...) }; ... { PCI_VENDOR_..., (kernel_ulong_t)&gpu_ccgx_ucsi } ... ? Though it's up to you. More important is to split this part to a separate function, like static int gpu_populate_client(struct gpu_i2c_dev *i2cd, ...) { ... } ... status = gpu_populate_client(...); if (status) { ... } > + struct gpu_i2c_dev *i2cd; > + int status; > + > + i2cd = devm_kzalloc(&dev->dev, sizeof(struct gpu_i2c_dev), GFP_KERNEL); > + if (!i2cd) > + return -ENOMEM; > + > + i2cd->pci_dev = dev; > + pci_set_drvdata(dev, i2cd); > + > + status = pcim_enable_device(dev); > + if (status < 0) { > + dev_err(&dev->dev, "pcim_enable_device failed - %d\n", status); > + return status; > + } > + > + pci_set_master(dev); > + > + i2cd->regs = pcim_iomap(dev, 0, 0); > + if (!i2cd->regs) { > + dev_err(&dev->dev, "pcim_iomap failed\n"); > + return -ENOMEM; > + } > + > + status = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_MSI); > + if (status < 0) { > + dev_err(&dev->dev, "pci_alloc_irq_vectors err - %d\n", status); > + return status; > + } > + > + i2cd->do_start = true; > + mutex_init(&i2cd->mutex); > + enable_i2c_bus(i2cd); > + > + i2c_set_adapdata(&i2cd->adapter, i2cd); > + i2cd->adapter.owner = THIS_MODULE; > + strlcpy(i2cd->adapter.name, "NVIDIA GPU I2C adapter", > + sizeof(i2cd->adapter.name)); > + i2cd->adapter.algo = &gpu_i2c_algorithm; > + i2cd->adapter.dev.parent = &dev->dev; > + status = i2c_add_adapter(&i2cd->adapter); > + if (status < 0) { > + dev_err(&dev->dev, "i2c_add_adapter failed - %d\n", status); > + goto del_adapter; > + } > + > + gpu_i2c_ucsi_board_info.irq = dev->irq; > + i2cd->client = i2c_new_device(&i2cd->adapter, &gpu_i2c_ucsi_board_info); > + > + if (!i2cd->client) { > + dev_err(&dev->dev, "i2c_new_device failed - %d\n", status); > + status = -ENODEV; > + goto del_adapter; > + } > + > + pm_runtime_put_noidle(&dev->dev); > + pm_runtime_allow(&dev->dev); > + > + return 0; > + > +del_adapter: > + i2c_del_adapter(&i2cd->adapter); > + pci_free_irq_vectors(dev); > + return status; > +} > + > +static void gpu_i2c_remove(struct pci_dev *dev) > +{ > + struct gpu_i2c_dev *i2cd = pci_get_drvdata(dev); > + > + i2c_del_adapter(&i2cd->adapter); > + pci_free_irq_vectors(dev); > +} > + > +static int gpu_i2c_resume(struct device *dev) > +{ > + struct gpu_i2c_dev *i2cd = pci_get_drvdata(to_pci_dev(dev)); > + > + enable_i2c_bus(i2cd); > + return 0; > +} > + > +static int gpu_i2c_idle(struct device *dev) > +{ > + struct gpu_i2c_dev *i2cd = pci_get_drvdata(to_pci_dev(dev)); > + > + if (!mutex_trylock(&i2cd->mutex)) { > + dev_info(dev, "-EBUSY\n"); > + return -EBUSY; > + } > + mutex_unlock(&i2cd->mutex); > + > + return 0; > +} > + > +UNIVERSAL_DEV_PM_OPS(gpu_i2c_driver_pm, NULL, gpu_i2c_resume, gpu_i2c_idle); > + > +static struct pci_driver gpu_i2c_driver = { > + .name = "nvidia-gpu", > + .id_table = gpu_i2c_ids, > + .probe = gpu_i2c_probe, > + .remove = gpu_i2c_remove, > + .driver = { > + .pm = &gpu_i2c_driver_pm, > + }, > +}; > + > +module_pci_driver(gpu_i2c_driver); > + > +MODULE_AUTHOR("Ajay Gupta <ajayg@nvidia.com>"); > +MODULE_DESCRIPTION("Nvidia GPU I2C controller Driver"); > +MODULE_LICENSE("GPL v2"); > -- > 2.7.4 >
Hi Andy, > > Latest NVIDIA GPU card has USB Type-C interface. There is a Type-C > > controller which can be accessed over I2C. > > > > This driver adds I2C bus driver to communicate with Type-C controller. > > I2C client driver will be part of USB Type-C UCSI driver. > > > > Some small comments below, after addressing them > > Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> > > > Signed-off-by: Ajay Gupta <ajayg@nvidia.com> > > --- > > Changes from v1 -> v2 > > None > > Changes from v2 -> v3 > > Fixed review comments from Andy and Thierry > > Rename i2c-gpu.c -> i2c-nvidia-gpu.c > > > > Documentation/i2c/busses/i2c-nvidia-gpu | 18 ++ > > MAINTAINERS | 7 + > > drivers/i2c/busses/Kconfig | 9 + > > drivers/i2c/busses/Makefile | 1 + > > drivers/i2c/busses/i2c-nvidia-gpu.c | 389 > ++++++++++++++++++++++++++++++++ > > 5 files changed, 424 insertions(+) > > create mode 100644 Documentation/i2c/busses/i2c-nvidia-gpu > > create mode 100644 drivers/i2c/busses/i2c-nvidia-gpu.c > > > > diff --git a/Documentation/i2c/busses/i2c-nvidia-gpu > > b/Documentation/i2c/busses/i2c-nvidia-gpu > > new file mode 100644 > > index 0000000..31884d2 > > --- /dev/null > > +++ b/Documentation/i2c/busses/i2c-nvidia-gpu > > @@ -0,0 +1,18 @@ > > +Kernel driver i2c-nvidia-gpu > > + > > +Datasheet: not publicly available. > > + > > +Authors: > > + Ajay Gupta <ajayg@nvidia.com> > > + > > +Description > > +----------- > > + > > +i2c-nvidia-gpu is a driver for I2C controller included in NVIDIA > > +Turing and later GPUs and it is used to communicate with Type-C controller > on GPUs. > > + > > +If your 'lspci -v' listing shows something like the following, > > + > > +01:00.3 Serial bus controller [0c80]: NVIDIA Corporation Device 1ad9 > > +(rev a1) > > + > > +then this driver should support the I2C controller of your GPU. > > diff --git a/MAINTAINERS b/MAINTAINERS index 9ad052a..2d1c5a1 100644 > > --- a/MAINTAINERS > > +++ b/MAINTAINERS > > @@ -6797,6 +6797,13 @@ L: linux-acpi@vger.kernel.org > > S: Maintained > > F: drivers/i2c/i2c-core-acpi.c > > > > +I2C CONTROLLER DRIVER FOR NVIDIA GPU > > +M: Ajay Gupta <ajayg@nvidia.com> > > +L: linux-i2c@vger.kernel.org > > +S: Maintained > > +F: Documentation/i2c/busses/i2c-nvidia-gpu > > +F: drivers/i2c/busses/i2c-nvidia-gpu.c > > + > > I2C MUXES > > M: Peter Rosin <peda@axentia.se> > > L: linux-i2c@vger.kernel.org > > diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig > > index 451d4ae..eed827b 100644 > > --- a/drivers/i2c/busses/Kconfig > > +++ b/drivers/i2c/busses/Kconfig > > @@ -224,6 +224,15 @@ config I2C_NFORCE2_S4985 > > This driver can also be built as a module. If so, the module > > will be called i2c-nforce2-s4985. > > > > +config I2C_NVIDIA_GPU > > + tristate "NVIDIA GPU I2C controller" > > + depends on PCI > > + help > > + If you say yes to this option, support will be included for the > > + NVIDIA GPU I2C controller which is used to communicate with the > GPU's > > + Type-C controller. This driver can also be built as a module called > > + i2c-nvidia-gpu. > > + > > config I2C_SIS5595 > > tristate "SiS 5595" > > depends on PCI > > diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile > > index 18b26af..d499813 100644 > > --- a/drivers/i2c/busses/Makefile > > +++ b/drivers/i2c/busses/Makefile > > @@ -140,5 +140,6 @@ obj-$(CONFIG_I2C_SIBYTE) += i2c-sibyte.o > > obj-$(CONFIG_I2C_XGENE_SLIMPRO) += i2c-xgene-slimpro.o > > obj-$(CONFIG_SCx200_ACB) += scx200_acb.o > > obj-$(CONFIG_I2C_FSI) += i2c-fsi.o > > +obj-$(CONFIG_I2C_NVIDIA_GPU) += i2c-nvidia-gpu.o > > > > ccflags-$(CONFIG_I2C_DEBUG_BUS) := -DDEBUG diff --git > > a/drivers/i2c/busses/i2c-nvidia-gpu.c > > b/drivers/i2c/busses/i2c-nvidia-gpu.c > > new file mode 100644 > > index 0000000..fa01187 > > --- /dev/null > > +++ b/drivers/i2c/busses/i2c-nvidia-gpu.c > > @@ -0,0 +1,389 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* > > + * Nvidia GPU I2C controller Driver > > + * > > + * Copyright (C) 2018 NVIDIA Corporation. All rights reserved. > > + * Author: Ajay Gupta <ajayg@nvidia.com> > > > + * > > Redundant line. > > > + */ ok > > > +#include <asm/unaligned.h> > > This should go after linux/* ones... > > > +#include <linux/delay.h> > > +#include <linux/i2c.h> > > +#include <linux/interrupt.h> > > +#include <linux/module.h> > > +#include <linux/pci.h> > > +#include <linux/platform_device.h> > > +#include <linux/pm.h> > > +#include <linux/pm_runtime.h> > > + > > ...here. will fix > > > +/* I2C definitions */ > > +#define I2C_MST_CNTL 0x0 > > +#define I2C_MST_CNTL_GEN_START BIT(0) > > +#define I2C_MST_CNTL_GEN_STOP BIT(1) > > +#define I2C_MST_CNTL_CMD_NONE (0 << 2) > > +#define I2C_MST_CNTL_CMD_READ (1 << 2) > > +#define I2C_MST_CNTL_CMD_WRITE (2 << 2) > > +#define I2C_MST_CNTL_GEN_RAB BIT(4) > > > +#define I2C_MST_CNTL_BURST_SIZE_SHIFT (6) > > Redundant parens > > > +#define I2C_MST_CNTL_GEN_NACK BIT(28) > > +#define I2C_MST_CNTL_STATUS (3 << 29) > > +#define I2C_MST_CNTL_STATUS_OKAY (0 << 29) > > +#define I2C_MST_CNTL_STATUS_NO_ACK (1 << 29) > > +#define I2C_MST_CNTL_STATUS_TIMEOUT (2 << 29) > > +#define I2C_MST_CNTL_STATUS_BUS_BUSY (3 << 29) > > +#define I2C_MST_CNTL_CYCLE_TRIGGER BIT(31) > > + > > +#define I2C_MST_ADDR 0x04 > > +#define I2C_MST_ADDR_DAB 0 > > + > > +#define I2C_MST_I2C0_TIMING 0x08 > > +#define I2C_MST_I2C0_TIMING_SCL_PERIOD_100KHZ 0x10e > > +#define I2C_MST_I2C0_TIMING_TIMEOUT_CLK_CNT 16 > > +#define I2C_MST_I2C0_TIMING_TIMEOUT_CLK_CNT_MAX 255 > > +#define I2C_MST_I2C0_TIMING_TIMEOUT_CHECK BIT(24) > > + > > +#define I2C_MST_DATA 0x0c > > + > > +#define I2C_MST_HYBRID_PADCTL 0x20 > > +#define I2C_MST_HYBRID_PADCTL_MODE_I2C BIT(0) > > +#define I2C_MST_HYBRID_PADCTL_I2C_SCL_INPUT_RCV BIT(14) > > +#define I2C_MST_HYBRID_PADCTL_I2C_SDA_INPUT_RCV BIT(15) > > + > > +struct gpu_i2c_dev { > > > + struct pci_dev *pci_dev; > > This should be a good argument why you are keeping struct pci_dev instead of > struct device. sure > > > + void __iomem *regs; > > + struct i2c_adapter adapter; > > + struct i2c_client *client; > > + struct mutex mutex; /* to sync read/write */ > > + bool do_start; > > +}; > > + > > +static void enable_i2c_bus(struct gpu_i2c_dev *i2cd) { > > + u32 val; > > + > > + /* enable I2C */ > > + val = readl(i2cd->regs + I2C_MST_HYBRID_PADCTL); > > + val |= I2C_MST_HYBRID_PADCTL_MODE_I2C | > > + I2C_MST_HYBRID_PADCTL_I2C_SCL_INPUT_RCV | > > + I2C_MST_HYBRID_PADCTL_I2C_SDA_INPUT_RCV; > > + writel(val, i2cd->regs + I2C_MST_HYBRID_PADCTL); > > + > > + /* enable 100KHZ mode */ > > + val = I2C_MST_I2C0_TIMING_SCL_PERIOD_100KHZ; > > + val |= (I2C_MST_I2C0_TIMING_TIMEOUT_CLK_CNT_MAX > > + << I2C_MST_I2C0_TIMING_TIMEOUT_CLK_CNT); > > + val |= I2C_MST_I2C0_TIMING_TIMEOUT_CHECK; > > + writel(val, i2cd->regs + I2C_MST_I2C0_TIMING); } > > + > > +static int i2c_check_status(struct gpu_i2c_dev *i2cd) { > > + unsigned long target = jiffies + msecs_to_jiffies(1000); > > > + int status = -EIO; > > You can get rid of this variable by returning in place. Sounds good > > > + u32 val; > > + > > + do { > > + val = readl(i2cd->regs + I2C_MST_CNTL); > > + if ((val & I2C_MST_CNTL_CYCLE_TRIGGER) != > > + I2C_MST_CNTL_CYCLE_TRIGGER) > > + break; > > + if ((val & I2C_MST_CNTL_STATUS) != > > + I2C_MST_CNTL_STATUS_BUS_BUSY) > > + break; > > + usleep_range(1000, 2000); > > + } while (time_is_after_jiffies(target)); > > + > > + if (time_is_before_jiffies(target)) > > + return status; > > + > > + val = readl(i2cd->regs + I2C_MST_CNTL); > > + switch (val & I2C_MST_CNTL_STATUS) { > > + case I2C_MST_CNTL_STATUS_OKAY: > > + status = 0; > > + break; > > + case I2C_MST_CNTL_STATUS_NO_ACK: > > + status = -EIO; > > + break; > > + case I2C_MST_CNTL_STATUS_TIMEOUT: > > + status = -ETIME; > > + break; > > + case I2C_MST_CNTL_STATUS_BUS_BUSY: > > + status = -EBUSY; > > + break; > > + default: > > + break; > > + } > > + return status; > > +} > > + > > +static int i2c_read(struct gpu_i2c_dev *i2cd, u8 *data, u16 len) { > > + int status; > > + u32 val = 0; > > + > > + val |= I2C_MST_CNTL_GEN_START | I2C_MST_CNTL_GEN_STOP | > > + I2C_MST_CNTL_CMD_READ | (len << > I2C_MST_CNTL_BURST_SIZE_SHIFT) | > > + I2C_MST_CNTL_CYCLE_TRIGGER | I2C_MST_CNTL_GEN_NACK; > > + val &= ~I2C_MST_CNTL_GEN_RAB; > > + writel(val, i2cd->regs + I2C_MST_CNTL); > > + > > + status = i2c_check_status(i2cd); > > + if (status < 0) > > + return status; > > + > > + val = readl(i2cd->regs + I2C_MST_DATA); > > + switch (len) { > > + case 1: > > + data[0] = val; > > + break; > > + case 2: > > + put_unaligned_be16(val, data); > > + break; > > + case 3: > > + put_unaligned_be16(val >> 8, data); > > + data[2] = val; > > + break; > > + case 4: > > + put_unaligned_be32(val, data); > > + break; > > + default: > > + break; > > + } > > + return status; > > +} > > + > > +static int i2c_start(struct gpu_i2c_dev *i2cd, u16 addr) { > > + u32 val; > > + > > + val = addr << I2C_MST_ADDR_DAB; > > + writel(val, i2cd->regs + I2C_MST_ADDR); > > + > > + val = I2C_MST_CNTL_GEN_START | I2C_MST_CNTL_CMD_NONE | > > + I2C_MST_CNTL_GEN_NACK; > > + val &= ~(I2C_MST_CNTL_GEN_STOP | I2C_MST_CNTL_GEN_RAB); > > + writel(val, i2cd->regs + I2C_MST_CNTL); > > + > > + return i2c_check_status(i2cd); } > > + > > +static int i2c_stop(struct gpu_i2c_dev *i2cd) { > > + u32 val; > > + > > + val = I2C_MST_CNTL_GEN_STOP | I2C_MST_CNTL_CMD_NONE | > > + I2C_MST_CNTL_GEN_NACK; > > + val &= ~(I2C_MST_CNTL_GEN_START | I2C_MST_CNTL_GEN_RAB); > > + writel(val, i2cd->regs + I2C_MST_CNTL); > > + > > + return i2c_check_status(i2cd); } > > + > > +static int i2c_write(struct gpu_i2c_dev *i2cd, u8 data) { > > + u32 val; > > + > > + writel(data, i2cd->regs + I2C_MST_DATA); > > + > > + val = I2C_MST_CNTL_CMD_WRITE | (1 << > I2C_MST_CNTL_BURST_SIZE_SHIFT) | > > + I2C_MST_CNTL_GEN_NACK; > > + val &= ~(I2C_MST_CNTL_GEN_START | I2C_MST_CNTL_GEN_STOP > > + | I2C_MST_CNTL_GEN_RAB); > > + writel(val, i2cd->regs + I2C_MST_CNTL); > > + > > + return i2c_check_status(i2cd); } > > + > > +static int gpu_i2c_master_xfer(struct i2c_adapter *adap, > > + struct i2c_msg *msgs, int num) { > > + struct gpu_i2c_dev *i2cd = i2c_get_adapdata(adap); > > + struct device *dev = &i2cd->pci_dev->dev; > > > + int sts; > > Btw, be consistent with names, status looks slightly better. ok > > > + int i, j; > > + > > + mutex_lock(&i2cd->mutex); > > + for (i = 0; i < num; i++) { > > + if (msgs[i].flags & I2C_M_RD) { > > + sts = i2c_read(i2cd, msgs[i].buf, msgs[i].len); > > + if (sts < 0) { > > + dev_err(dev, "i2c_read error %x", sts); > > + break; > > + } > > + i2cd->do_start = true; > > + } else if (msgs[i].flags & I2C_M_STOP) { > > + sts = i2c_stop(i2cd); > > + if (sts < 0) { > > + dev_err(dev, "i2c_stop error %x", sts); > > + goto unlock; > > + } > > + i2cd->do_start = true; > > + } else { > > + if (i2cd->do_start) { > > + sts = i2c_start(i2cd, msgs[i].addr); > > + if (sts < 0) { > > + dev_err(dev, "i2c_start error %x", sts); > > + goto unlock; > > + } > > + sts = i2c_write(i2cd, msgs[i].addr << 1); > > + if (sts < 0) { > > + dev_err(dev, "i2c_write error %x", sts); > > + goto stop; > > + } > > + i2cd->do_start = false; > > + } > > + for (j = 0; j < msgs[i].len; j++) { > > + sts = i2c_write(i2cd, *(msgs[i].buf + j)); > > + if (sts < 0) { > > + dev_err(dev, "i2c_write error %x", sts); > > + goto stop; > > + } > > + } > > + } > > + } > > + goto unlock; > > +stop: > > + sts = i2c_stop(i2cd); > > + if (sts < 0) > > + dev_err(dev, "i2c_stop error %x", sts); > > +unlock: > > + mutex_unlock(&i2cd->mutex); > > + return i; > > +} > > + > > +static u32 gpu_i2c_functionality(struct i2c_adapter *adap) { > > + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; } > > + > > +static const struct i2c_algorithm gpu_i2c_algorithm = { > > + .master_xfer = gpu_i2c_master_xfer, > > + .functionality = gpu_i2c_functionality, }; > > + > > > +#define PCI_CLASS_SERIAL_UNKNOWN 0x0c80 > > +static const struct pci_device_id gpu_i2c_ids[] = { > > + { PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, > > + PCI_CLASS_SERIAL_UNKNOWN << 8, 0xffffff00}, > > + { } > > +}; > > I'm really in doubt how it's supposed to be enumerated without conflicts or > shadowing other hardware. > Explain in the comments, please. Will add comments. > > > +MODULE_DEVICE_TABLE(pci, gpu_i2c_ids); > > + > > +static int gpu_i2c_probe(struct pci_dev *dev, const struct > > +pci_device_id *id) { > > > + struct i2c_board_info gpu_i2c_ucsi_board_info = { > > + I2C_BOARD_INFO("ccgx-ucsi", 0x8) > > + }; > > Can't you rather put this as static const which is provided in driver_data above Can't add as "const" since I am saving "irq" field from pci_dev->irq but will add new function gpu_populate_client() Thanks Ajay -- nvpublic --
On Wed, Aug 29, 2018 at 05:33:17PM -0700, ajaykuee@gmail.com wrote:
> From: Ajay Gupta <ajayg@nvidia.com>
Can you add your full name to the gmail address, too? That would make
patch processing a tad easier.
Thanks,
Wolfram
diff --git a/Documentation/i2c/busses/i2c-nvidia-gpu b/Documentation/i2c/busses/i2c-nvidia-gpu new file mode 100644 index 0000000..31884d2 --- /dev/null +++ b/Documentation/i2c/busses/i2c-nvidia-gpu @@ -0,0 +1,18 @@ +Kernel driver i2c-nvidia-gpu + +Datasheet: not publicly available. + +Authors: + Ajay Gupta <ajayg@nvidia.com> + +Description +----------- + +i2c-nvidia-gpu is a driver for I2C controller included in NVIDIA Turing +and later GPUs and it is used to communicate with Type-C controller on GPUs. + +If your 'lspci -v' listing shows something like the following, + +01:00.3 Serial bus controller [0c80]: NVIDIA Corporation Device 1ad9 (rev a1) + +then this driver should support the I2C controller of your GPU. diff --git a/MAINTAINERS b/MAINTAINERS index 9ad052a..2d1c5a1 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -6797,6 +6797,13 @@ L: linux-acpi@vger.kernel.org S: Maintained F: drivers/i2c/i2c-core-acpi.c +I2C CONTROLLER DRIVER FOR NVIDIA GPU +M: Ajay Gupta <ajayg@nvidia.com> +L: linux-i2c@vger.kernel.org +S: Maintained +F: Documentation/i2c/busses/i2c-nvidia-gpu +F: drivers/i2c/busses/i2c-nvidia-gpu.c + I2C MUXES M: Peter Rosin <peda@axentia.se> L: linux-i2c@vger.kernel.org diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index 451d4ae..eed827b 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -224,6 +224,15 @@ config I2C_NFORCE2_S4985 This driver can also be built as a module. If so, the module will be called i2c-nforce2-s4985. +config I2C_NVIDIA_GPU + tristate "NVIDIA GPU I2C controller" + depends on PCI + help + If you say yes to this option, support will be included for the + NVIDIA GPU I2C controller which is used to communicate with the GPU's + Type-C controller. This driver can also be built as a module called + i2c-nvidia-gpu. + config I2C_SIS5595 tristate "SiS 5595" depends on PCI diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile index 18b26af..d499813 100644 --- a/drivers/i2c/busses/Makefile +++ b/drivers/i2c/busses/Makefile @@ -140,5 +140,6 @@ obj-$(CONFIG_I2C_SIBYTE) += i2c-sibyte.o obj-$(CONFIG_I2C_XGENE_SLIMPRO) += i2c-xgene-slimpro.o obj-$(CONFIG_SCx200_ACB) += scx200_acb.o obj-$(CONFIG_I2C_FSI) += i2c-fsi.o +obj-$(CONFIG_I2C_NVIDIA_GPU) += i2c-nvidia-gpu.o ccflags-$(CONFIG_I2C_DEBUG_BUS) := -DDEBUG diff --git a/drivers/i2c/busses/i2c-nvidia-gpu.c b/drivers/i2c/busses/i2c-nvidia-gpu.c new file mode 100644 index 0000000..fa01187 --- /dev/null +++ b/drivers/i2c/busses/i2c-nvidia-gpu.c @@ -0,0 +1,389 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Nvidia GPU I2C controller Driver + * + * Copyright (C) 2018 NVIDIA Corporation. All rights reserved. + * Author: Ajay Gupta <ajayg@nvidia.com> + * + */ +#include <asm/unaligned.h> +#include <linux/delay.h> +#include <linux/i2c.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/platform_device.h> +#include <linux/pm.h> +#include <linux/pm_runtime.h> + +/* I2C definitions */ +#define I2C_MST_CNTL 0x0 +#define I2C_MST_CNTL_GEN_START BIT(0) +#define I2C_MST_CNTL_GEN_STOP BIT(1) +#define I2C_MST_CNTL_CMD_NONE (0 << 2) +#define I2C_MST_CNTL_CMD_READ (1 << 2) +#define I2C_MST_CNTL_CMD_WRITE (2 << 2) +#define I2C_MST_CNTL_GEN_RAB BIT(4) +#define I2C_MST_CNTL_BURST_SIZE_SHIFT (6) +#define I2C_MST_CNTL_GEN_NACK BIT(28) +#define I2C_MST_CNTL_STATUS (3 << 29) +#define I2C_MST_CNTL_STATUS_OKAY (0 << 29) +#define I2C_MST_CNTL_STATUS_NO_ACK (1 << 29) +#define I2C_MST_CNTL_STATUS_TIMEOUT (2 << 29) +#define I2C_MST_CNTL_STATUS_BUS_BUSY (3 << 29) +#define I2C_MST_CNTL_CYCLE_TRIGGER BIT(31) + +#define I2C_MST_ADDR 0x04 +#define I2C_MST_ADDR_DAB 0 + +#define I2C_MST_I2C0_TIMING 0x08 +#define I2C_MST_I2C0_TIMING_SCL_PERIOD_100KHZ 0x10e +#define I2C_MST_I2C0_TIMING_TIMEOUT_CLK_CNT 16 +#define I2C_MST_I2C0_TIMING_TIMEOUT_CLK_CNT_MAX 255 +#define I2C_MST_I2C0_TIMING_TIMEOUT_CHECK BIT(24) + +#define I2C_MST_DATA 0x0c + +#define I2C_MST_HYBRID_PADCTL 0x20 +#define I2C_MST_HYBRID_PADCTL_MODE_I2C BIT(0) +#define I2C_MST_HYBRID_PADCTL_I2C_SCL_INPUT_RCV BIT(14) +#define I2C_MST_HYBRID_PADCTL_I2C_SDA_INPUT_RCV BIT(15) + +struct gpu_i2c_dev { + struct pci_dev *pci_dev; + void __iomem *regs; + struct i2c_adapter adapter; + struct i2c_client *client; + struct mutex mutex; /* to sync read/write */ + bool do_start; +}; + +static void enable_i2c_bus(struct gpu_i2c_dev *i2cd) +{ + u32 val; + + /* enable I2C */ + val = readl(i2cd->regs + I2C_MST_HYBRID_PADCTL); + val |= I2C_MST_HYBRID_PADCTL_MODE_I2C | + I2C_MST_HYBRID_PADCTL_I2C_SCL_INPUT_RCV | + I2C_MST_HYBRID_PADCTL_I2C_SDA_INPUT_RCV; + writel(val, i2cd->regs + I2C_MST_HYBRID_PADCTL); + + /* enable 100KHZ mode */ + val = I2C_MST_I2C0_TIMING_SCL_PERIOD_100KHZ; + val |= (I2C_MST_I2C0_TIMING_TIMEOUT_CLK_CNT_MAX + << I2C_MST_I2C0_TIMING_TIMEOUT_CLK_CNT); + val |= I2C_MST_I2C0_TIMING_TIMEOUT_CHECK; + writel(val, i2cd->regs + I2C_MST_I2C0_TIMING); +} + +static int i2c_check_status(struct gpu_i2c_dev *i2cd) +{ + unsigned long target = jiffies + msecs_to_jiffies(1000); + int status = -EIO; + u32 val; + + do { + val = readl(i2cd->regs + I2C_MST_CNTL); + if ((val & I2C_MST_CNTL_CYCLE_TRIGGER) != + I2C_MST_CNTL_CYCLE_TRIGGER) + break; + if ((val & I2C_MST_CNTL_STATUS) != + I2C_MST_CNTL_STATUS_BUS_BUSY) + break; + usleep_range(1000, 2000); + } while (time_is_after_jiffies(target)); + + if (time_is_before_jiffies(target)) + return status; + + val = readl(i2cd->regs + I2C_MST_CNTL); + switch (val & I2C_MST_CNTL_STATUS) { + case I2C_MST_CNTL_STATUS_OKAY: + status = 0; + break; + case I2C_MST_CNTL_STATUS_NO_ACK: + status = -EIO; + break; + case I2C_MST_CNTL_STATUS_TIMEOUT: + status = -ETIME; + break; + case I2C_MST_CNTL_STATUS_BUS_BUSY: + status = -EBUSY; + break; + default: + break; + } + return status; +} + +static int i2c_read(struct gpu_i2c_dev *i2cd, u8 *data, u16 len) +{ + int status; + u32 val = 0; + + val |= I2C_MST_CNTL_GEN_START | I2C_MST_CNTL_GEN_STOP | + I2C_MST_CNTL_CMD_READ | (len << I2C_MST_CNTL_BURST_SIZE_SHIFT) | + I2C_MST_CNTL_CYCLE_TRIGGER | I2C_MST_CNTL_GEN_NACK; + val &= ~I2C_MST_CNTL_GEN_RAB; + writel(val, i2cd->regs + I2C_MST_CNTL); + + status = i2c_check_status(i2cd); + if (status < 0) + return status; + + val = readl(i2cd->regs + I2C_MST_DATA); + switch (len) { + case 1: + data[0] = val; + break; + case 2: + put_unaligned_be16(val, data); + break; + case 3: + put_unaligned_be16(val >> 8, data); + data[2] = val; + break; + case 4: + put_unaligned_be32(val, data); + break; + default: + break; + } + return status; +} + +static int i2c_start(struct gpu_i2c_dev *i2cd, u16 addr) +{ + u32 val; + + val = addr << I2C_MST_ADDR_DAB; + writel(val, i2cd->regs + I2C_MST_ADDR); + + val = I2C_MST_CNTL_GEN_START | I2C_MST_CNTL_CMD_NONE | + I2C_MST_CNTL_GEN_NACK; + val &= ~(I2C_MST_CNTL_GEN_STOP | I2C_MST_CNTL_GEN_RAB); + writel(val, i2cd->regs + I2C_MST_CNTL); + + return i2c_check_status(i2cd); +} + +static int i2c_stop(struct gpu_i2c_dev *i2cd) +{ + u32 val; + + val = I2C_MST_CNTL_GEN_STOP | I2C_MST_CNTL_CMD_NONE | + I2C_MST_CNTL_GEN_NACK; + val &= ~(I2C_MST_CNTL_GEN_START | I2C_MST_CNTL_GEN_RAB); + writel(val, i2cd->regs + I2C_MST_CNTL); + + return i2c_check_status(i2cd); +} + +static int i2c_write(struct gpu_i2c_dev *i2cd, u8 data) +{ + u32 val; + + writel(data, i2cd->regs + I2C_MST_DATA); + + val = I2C_MST_CNTL_CMD_WRITE | (1 << I2C_MST_CNTL_BURST_SIZE_SHIFT) | + I2C_MST_CNTL_GEN_NACK; + val &= ~(I2C_MST_CNTL_GEN_START | I2C_MST_CNTL_GEN_STOP + | I2C_MST_CNTL_GEN_RAB); + writel(val, i2cd->regs + I2C_MST_CNTL); + + return i2c_check_status(i2cd); +} + +static int gpu_i2c_master_xfer(struct i2c_adapter *adap, + struct i2c_msg *msgs, int num) +{ + struct gpu_i2c_dev *i2cd = i2c_get_adapdata(adap); + struct device *dev = &i2cd->pci_dev->dev; + int sts; + int i, j; + + mutex_lock(&i2cd->mutex); + for (i = 0; i < num; i++) { + if (msgs[i].flags & I2C_M_RD) { + sts = i2c_read(i2cd, msgs[i].buf, msgs[i].len); + if (sts < 0) { + dev_err(dev, "i2c_read error %x", sts); + break; + } + i2cd->do_start = true; + } else if (msgs[i].flags & I2C_M_STOP) { + sts = i2c_stop(i2cd); + if (sts < 0) { + dev_err(dev, "i2c_stop error %x", sts); + goto unlock; + } + i2cd->do_start = true; + } else { + if (i2cd->do_start) { + sts = i2c_start(i2cd, msgs[i].addr); + if (sts < 0) { + dev_err(dev, "i2c_start error %x", sts); + goto unlock; + } + sts = i2c_write(i2cd, msgs[i].addr << 1); + if (sts < 0) { + dev_err(dev, "i2c_write error %x", sts); + goto stop; + } + i2cd->do_start = false; + } + for (j = 0; j < msgs[i].len; j++) { + sts = i2c_write(i2cd, *(msgs[i].buf + j)); + if (sts < 0) { + dev_err(dev, "i2c_write error %x", sts); + goto stop; + } + } + } + } + goto unlock; +stop: + sts = i2c_stop(i2cd); + if (sts < 0) + dev_err(dev, "i2c_stop error %x", sts); +unlock: + mutex_unlock(&i2cd->mutex); + return i; +} + +static u32 gpu_i2c_functionality(struct i2c_adapter *adap) +{ + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; +} + +static const struct i2c_algorithm gpu_i2c_algorithm = { + .master_xfer = gpu_i2c_master_xfer, + .functionality = gpu_i2c_functionality, +}; + +#define PCI_CLASS_SERIAL_UNKNOWN 0x0c80 +static const struct pci_device_id gpu_i2c_ids[] = { + { PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, + PCI_CLASS_SERIAL_UNKNOWN << 8, 0xffffff00}, + { } +}; +MODULE_DEVICE_TABLE(pci, gpu_i2c_ids); + +static int gpu_i2c_probe(struct pci_dev *dev, const struct pci_device_id *id) +{ + struct i2c_board_info gpu_i2c_ucsi_board_info = { + I2C_BOARD_INFO("ccgx-ucsi", 0x8) + }; + struct gpu_i2c_dev *i2cd; + int status; + + i2cd = devm_kzalloc(&dev->dev, sizeof(struct gpu_i2c_dev), GFP_KERNEL); + if (!i2cd) + return -ENOMEM; + + i2cd->pci_dev = dev; + pci_set_drvdata(dev, i2cd); + + status = pcim_enable_device(dev); + if (status < 0) { + dev_err(&dev->dev, "pcim_enable_device failed - %d\n", status); + return status; + } + + pci_set_master(dev); + + i2cd->regs = pcim_iomap(dev, 0, 0); + if (!i2cd->regs) { + dev_err(&dev->dev, "pcim_iomap failed\n"); + return -ENOMEM; + } + + status = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_MSI); + if (status < 0) { + dev_err(&dev->dev, "pci_alloc_irq_vectors err - %d\n", status); + return status; + } + + i2cd->do_start = true; + mutex_init(&i2cd->mutex); + enable_i2c_bus(i2cd); + + i2c_set_adapdata(&i2cd->adapter, i2cd); + i2cd->adapter.owner = THIS_MODULE; + strlcpy(i2cd->adapter.name, "NVIDIA GPU I2C adapter", + sizeof(i2cd->adapter.name)); + i2cd->adapter.algo = &gpu_i2c_algorithm; + i2cd->adapter.dev.parent = &dev->dev; + status = i2c_add_adapter(&i2cd->adapter); + if (status < 0) { + dev_err(&dev->dev, "i2c_add_adapter failed - %d\n", status); + goto del_adapter; + } + + gpu_i2c_ucsi_board_info.irq = dev->irq; + i2cd->client = i2c_new_device(&i2cd->adapter, &gpu_i2c_ucsi_board_info); + + if (!i2cd->client) { + dev_err(&dev->dev, "i2c_new_device failed - %d\n", status); + status = -ENODEV; + goto del_adapter; + } + + pm_runtime_put_noidle(&dev->dev); + pm_runtime_allow(&dev->dev); + + return 0; + +del_adapter: + i2c_del_adapter(&i2cd->adapter); + pci_free_irq_vectors(dev); + return status; +} + +static void gpu_i2c_remove(struct pci_dev *dev) +{ + struct gpu_i2c_dev *i2cd = pci_get_drvdata(dev); + + i2c_del_adapter(&i2cd->adapter); + pci_free_irq_vectors(dev); +} + +static int gpu_i2c_resume(struct device *dev) +{ + struct gpu_i2c_dev *i2cd = pci_get_drvdata(to_pci_dev(dev)); + + enable_i2c_bus(i2cd); + return 0; +} + +static int gpu_i2c_idle(struct device *dev) +{ + struct gpu_i2c_dev *i2cd = pci_get_drvdata(to_pci_dev(dev)); + + if (!mutex_trylock(&i2cd->mutex)) { + dev_info(dev, "-EBUSY\n"); + return -EBUSY; + } + mutex_unlock(&i2cd->mutex); + + return 0; +} + +UNIVERSAL_DEV_PM_OPS(gpu_i2c_driver_pm, NULL, gpu_i2c_resume, gpu_i2c_idle); + +static struct pci_driver gpu_i2c_driver = { + .name = "nvidia-gpu", + .id_table = gpu_i2c_ids, + .probe = gpu_i2c_probe, + .remove = gpu_i2c_remove, + .driver = { + .pm = &gpu_i2c_driver_pm, + }, +}; + +module_pci_driver(gpu_i2c_driver); + +MODULE_AUTHOR("Ajay Gupta <ajayg@nvidia.com>"); +MODULE_DESCRIPTION("Nvidia GPU I2C controller Driver"); +MODULE_LICENSE("GPL v2");