new file mode 100644
@@ -0,0 +1,157 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/eswin,eic7700-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Eswin Eic7700 Pinctrl
+
+maintainers:
+ - Yulin Lu <luyulin@eswincomputing.com>
+
+allOf:
+ - $ref: pinctrl.yaml#
+
+description: |
+ eic7700 pin configuration nodes act as a container for an arbitrary number of
+ subnodes. Each of these subnodes represents some desired configuration for one or
+ more pins. This configuration can include the mux function to select on those pin(s),
+ and various pin configuration parameters, such as input-enable, pull-up, etc.
+
+properties:
+ compatible:
+ const: eswin,eic7700-pinctrl
+
+ reg:
+ maxItems: 1
+
+ vrgmii-supply:
+ description:
+ Regulator supply for the RGMII interface IO power domain.
+ This property should reference a regulator that provides either 1.8V or 3.3V,
+ depending on the board-level voltage configuration required by the RGMII interface.
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+
+ patternProperties:
+ '-pins$':
+ type: object
+
+ properties:
+ pins:
+ description:
+ For eic7700, specifies the name(s) of one or more pins to be configured by
+ this node.
+ items:
+ enum: [ chip_mode, mode_set0, mode_set1, mode_set2, mode_set3, xin,
+ rst_out_n, key_reset_n, gpio0, por_sel, jtag0_tck, jtag0_tms,
+ jtag0_tdi, jtag0_tdo, gpio5, spi2_cs0_n, jtag1_tck, jtag1_tms,
+ jtag1_tdi, jtag1_tdo, gpio11, spi2_cs1_n, pcie_clkreq_n,
+ pcie_wake_n, pcie_perst_n, hdmi_scl, hdmi_sda, hdmi_cec,
+ jtag2_trst, rgmii0_clk_125, rgmii0_txen, rgmii0_txclk,
+ rgmii0_txd0, rgmii0_txd1, rgmii0_txd2, rgmii0_txd3, i2s0_bclk,
+ i2s0_wclk, i2s0_sdi, i2s0_sdo, i2s_mclk, rgmii0_rxclk,
+ rgmii0_rxdv, rgmii0_rxd0, rgmii0_rxd1, rgmii0_rxd2, rgmii0_rxd3,
+ i2s2_bclk, i2s2_wclk, i2s2_sdi, i2s2_sdo, gpio27, gpio28, gpio29,
+ rgmii0_mdc, rgmii0_mdio, rgmii0_intb, rgmii1_clk_125, rgmii1_txen,
+ rgmii1_txclk, rgmii1_txd0, rgmii1_txd1, rgmii1_txd2, rgmii1_txd3,
+ i2s1_bclk, i2s1_wclk, i2s1_sdi, i2s1_sdo, gpio34, rgmii1_rxclk,
+ rgmii1_rxdv, rgmii1_rxd0, rgmii1_rxd1, rgmii1_rxd2, rgmii1_rxd3,
+ spi1_cs0_n, spi1_clk, spi1_d0, spi1_d1, spi1_d2, spi1_d3, spi1_cs1_n,
+ rgmii1_mdc, rgmii1_mdio, rgmii1_intb, usb0_pwren, usb1_pwren,
+ i2c0_scl, i2c0_sda, i2c1_scl, i2c1_sda, i2c2_scl, i2c2_sda,
+ i2c3_scl, i2c3_sda, i2c4_scl, i2c4_sda, i2c5_scl, i2c5_sda,
+ uart0_tx, uart0_rx, uart1_tx, uart1_rx, uart1_cts, uart1_rts,
+ uart2_tx, uart2_rx, jtag2_tck, jtag2_tms, jtag2_tdi, jtag2_tdo,
+ fan_pwm, fan_tach, mipi_csi0_xvs, mipi_csi0_xhs, mipi_csi0_mclk,
+ mipi_csi1_xvs, mipi_csi1_xhs, mipi_csi1_mclk, mipi_csi2_xvs,
+ mipi_csi2_xhs, mipi_csi2_mclk, mipi_csi3_xvs, mipi_csi3_xhs,
+ mipi_csi3_mclk, mipi_csi4_xvs, mipi_csi4_xhs, mipi_csi4_mclk,
+ mipi_csi5_xvs, mipi_csi5_xhs, mipi_csi5_mclk, spi3_cs_n, spi3_clk,
+ spi3_di, spi3_do, gpio92, gpio93, s_mode, gpio95, spi0_cs_n,
+ spi0_clk, spi0_d0, spi0_d1, spi0_d2, spi0_d3, i2c10_scl,
+ i2c10_sda, i2c11_scl, i2c11_sda, gpio106, boot_sel0, boot_sel1,
+ boot_sel2, boot_sel3, gpio111, lpddr_ref_clk ]
+
+ function:
+ description:
+ Specify the alternative function to be configured for the
+ given pins.
+ enum: [ disabled, boot_sel, chip_mode, emmc, fan_tach,
+ gpio, hdmi, i2c, i2s, jtag, ddr_ref_clk_sel,
+ lpddr_ref_clk, mipi_csi, osc, pcie, pwm,
+ rgmii, reset, sata, sdio, spi, s_mode, uart, usb ]
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ bias-disable: true
+
+ bias-pull-down: true
+
+ bias-pull-up: true
+
+ input-enable: true
+
+ input-disable: true
+
+ drive-strength-microamp: true
+
+ required:
+ - pins
+
+ additionalProperties: false
+
+ allOf:
+ - $ref: pincfg-node.yaml#
+ - $ref: pinmux-node.yaml#
+
+ - if:
+ properties:
+ pins:
+ anyOf:
+ - pattern: '^rgmii'
+ - const: lpddr_ref_clk
+ then:
+ properties:
+ drive-strength-microamp:
+ enum: [3000, 6000, 9000, 12000, 15000, 18000, 21000, 24000]
+ else:
+ properties:
+ drive-strength-microamp:
+ enum: [6000, 9000, 12000, 15000, 18000, 21000, 24000, 27000]
+
+
+required:
+ - compatible
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ pinctrl@51600080 {
+ compatible = "eswin,eic7700-pinctrl";
+ reg = <0x51600080 0x1fff80>;
+ vrgmii-supply = <&vcc_1v8>;
+
+ dev-active-grp{
+ /* group node defining 1 standard pin */
+ gpio10-pins {
+ pins = "jtag1_tdo";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ };
+
+ /* group node defining 2 I2C pins */
+ i2c6-pins {
+ pins = "uart1_cts", "uart1_rts";
+ function = "i2c";
+ };
+ };
+ };