diff mbox series

[v13,net-next,4/9] pinctrl: ocelot: add ability to be used in a non-mmio configuration

Message ID 20220705204743.3224692-5-colin.foster@in-advantage.com
State New
Headers show
Series add support for VSC7512 control over SPI | expand

Commit Message

Colin Foster July 5, 2022, 8:47 p.m. UTC 
There are a few Ocelot chips that contain pinctrl logic, but can be
controlled externally. Specifically the VSC7511, 7512, 7513 and 7514. In
the externally controlled configurations these registers are not
memory-mapped.

Add support for these non-memory-mapped configurations.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
---
 drivers/pinctrl/pinctrl-ocelot.c | 16 +++++-----------
 1 file changed, 5 insertions(+), 11 deletions(-)

Comments

Vladimir Oltean July 9, 2022, 6:59 p.m. UTC | #1 
On Tue, Jul 05, 2022 at 01:47:38PM -0700, Colin Foster wrote:
> There are a few Ocelot chips that contain pinctrl logic, but can be
> controlled externally. Specifically the VSC7511, 7512, 7513 and 7514. In
> the externally controlled configurations these registers are not
> memory-mapped.
> 
> Add support for these non-memory-mapped configurations.
> 
> Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
> ---

Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Linus Walleij July 11, 2022, 8:20 a.m. UTC | #2 
On Tue, Jul 5, 2022 at 10:48 PM Colin Foster
<colin.foster@in-advantage.com> wrote:

> There are a few Ocelot chips that contain pinctrl logic, but can be
> controlled externally. Specifically the VSC7511, 7512, 7513 and 7514. In
> the externally controlled configurations these registers are not
> memory-mapped.
>
> Add support for these non-memory-mapped configurations.
>
> Signed-off-by: Colin Foster <colin.foster@in-advantage.com>

Acked-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij
diff mbox series

Patch

diff --git a/drivers/pinctrl/pinctrl-ocelot.c b/drivers/pinctrl/pinctrl-ocelot.c
index d18047d2306d..80a3bba520cb 100644
--- a/drivers/pinctrl/pinctrl-ocelot.c
+++ b/drivers/pinctrl/pinctrl-ocelot.c
@@ -10,6 +10,7 @@ 
 #include <linux/gpio/driver.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
+#include <linux/mfd/ocelot.h>
 #include <linux/of_device.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
@@ -1918,7 +1919,6 @@  static int ocelot_pinctrl_probe(struct platform_device *pdev)
 	struct ocelot_pinctrl *info;
 	struct reset_control *reset;
 	struct regmap *pincfg;
-	void __iomem *base;
 	int ret;
 	struct regmap_config regmap_config = {
 		.reg_bits = 32,
@@ -1938,20 +1938,14 @@  static int ocelot_pinctrl_probe(struct platform_device *pdev)
 				     "Failed to get reset\n");
 	reset_control_reset(reset);
 
-	base = devm_ioremap_resource(dev,
-			platform_get_resource(pdev, IORESOURCE_MEM, 0));
-	if (IS_ERR(base))
-		return PTR_ERR(base);
-
 	info->stride = 1 + (info->desc->npins - 1) / 32;
 
 	regmap_config.max_register = OCELOT_GPIO_SD_MAP * info->stride + 15 * 4;
 
-	info->map = devm_regmap_init_mmio(dev, base, &regmap_config);
-	if (IS_ERR(info->map)) {
-		dev_err(dev, "Failed to create regmap\n");
-		return PTR_ERR(info->map);
-	}
+	info->map = ocelot_regmap_from_resource(pdev, 0, &regmap_config);
+	if (IS_ERR(info->map))
+		return dev_err_probe(dev, PTR_ERR(info->map),
+				     "Failed to create regmap\n");
 	dev_set_drvdata(dev, info->map);
 	info->dev = dev;