Message ID | 20210210132751.1422386-1-geert+renesas@glider.be |
---|---|
State | New |
Headers | show |
Series | pinctrl: PINCTRL_MICROCHIP_SGPIO should depend on ARCH_SPARX5 || SOC_VCOREIII | expand |
Geert Uytterhoeven writes: > the Microsemi/Microchip Serial GPIO device is present only Microsemi > VCore III and Microchip Sparx5 SoCs. Hence add a dependency on > ARCH_SPARX5 || SOC_VCOREIII, to prevent asking the user about this > driver when configuring a kernel without support for these SoCs. > > Fixes: 7e5ea974e61c8dd0 ("pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO") > Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> > --- > drivers/pinctrl/Kconfig | 4 ++-- > 1 file changed, 2 insertions(+), 2 deletions(-) > > diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig > index 113073d5f89bbf70..3b75b1d7d3d1f1b0 100644 > --- a/drivers/pinctrl/Kconfig > +++ b/drivers/pinctrl/Kconfig > @@ -353,8 +353,8 @@ config PINCTRL_OCELOT > > config PINCTRL_MICROCHIP_SGPIO > bool "Pinctrl driver for Microsemi/Microchip Serial GPIO" > - depends on OF > - depends on HAS_IOMEM > + depends on OF && HAS_IOMEM > + depends on ARCH_SPARX5 || SOC_VCOREIII || COMPILE_TEST > select GPIOLIB > select GPIOLIB_IRQCHIP > select GENERIC_PINCONF Geert, Thank you for your patch. Unfortunately, it makes it impossible to use the driver across PCIe - which is a specifically desired configuration. Could you add CONFIG_PCI to the || chain? Cheers,
Hi Lars, On Wed, Feb 10, 2021 at 2:45 PM Lars Povlsen <lars.povlsen@microchip.com> wrote: > Geert Uytterhoeven writes: > > the Microsemi/Microchip Serial GPIO device is present only Microsemi > > VCore III and Microchip Sparx5 SoCs. Hence add a dependency on > > ARCH_SPARX5 || SOC_VCOREIII, to prevent asking the user about this > > driver when configuring a kernel without support for these SoCs. > > > > Fixes: 7e5ea974e61c8dd0 ("pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO") > > Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> > > --- > > drivers/pinctrl/Kconfig | 4 ++-- > > 1 file changed, 2 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig > > index 113073d5f89bbf70..3b75b1d7d3d1f1b0 100644 > > --- a/drivers/pinctrl/Kconfig > > +++ b/drivers/pinctrl/Kconfig > > @@ -353,8 +353,8 @@ config PINCTRL_OCELOT > > > > config PINCTRL_MICROCHIP_SGPIO > > bool "Pinctrl driver for Microsemi/Microchip Serial GPIO" > > - depends on OF > > - depends on HAS_IOMEM > > + depends on OF && HAS_IOMEM > > + depends on ARCH_SPARX5 || SOC_VCOREIII || COMPILE_TEST > > select GPIOLIB > > select GPIOLIB_IRQCHIP > > select GENERIC_PINCONF > > Thank you for your patch. Unfortunately, it makes it impossible to use > the driver across PCIe - which is a specifically desired configuration. > > Could you add CONFIG_PCI to the || chain? Sure. Is PCIe the only other transport over which the register can be accessed? Or can this also be done over e.g. SPI, like on Ocelot[1]? [1] https://lore.kernel.org/linux-gpio/20200511145329.GV34497@piout.net/ Thanks! Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
On 10/02/2021 14:53:01+0100, Geert Uytterhoeven wrote: > Hi Lars, > > On Wed, Feb 10, 2021 at 2:45 PM Lars Povlsen <lars.povlsen@microchip.com> wrote: > > Geert Uytterhoeven writes: > > > the Microsemi/Microchip Serial GPIO device is present only Microsemi > > > VCore III and Microchip Sparx5 SoCs. Hence add a dependency on > > > ARCH_SPARX5 || SOC_VCOREIII, to prevent asking the user about this > > > driver when configuring a kernel without support for these SoCs. > > > > > > Fixes: 7e5ea974e61c8dd0 ("pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO") > > > Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> > > > --- > > > drivers/pinctrl/Kconfig | 4 ++-- > > > 1 file changed, 2 insertions(+), 2 deletions(-) > > > > > > diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig > > > index 113073d5f89bbf70..3b75b1d7d3d1f1b0 100644 > > > --- a/drivers/pinctrl/Kconfig > > > +++ b/drivers/pinctrl/Kconfig > > > @@ -353,8 +353,8 @@ config PINCTRL_OCELOT > > > > > > config PINCTRL_MICROCHIP_SGPIO > > > bool "Pinctrl driver for Microsemi/Microchip Serial GPIO" > > > - depends on OF > > > - depends on HAS_IOMEM > > > + depends on OF && HAS_IOMEM > > > + depends on ARCH_SPARX5 || SOC_VCOREIII || COMPILE_TEST > > > select GPIOLIB > > > select GPIOLIB_IRQCHIP > > > select GENERIC_PINCONF > > > > Thank you for your patch. Unfortunately, it makes it impossible to use > > the driver across PCIe - which is a specifically desired configuration. > > > > Could you add CONFIG_PCI to the || chain? > > Sure. > > Is PCIe the only other transport over which the register can be accessed? > Or can this also be done over e.g. SPI, like on Ocelot[1]? > > [1] https://lore.kernel.org/linux-gpio/20200511145329.GV34497@piout.net/ > Yes, this driver IP is also available on Ocelot (this is SOC_VCOREIII) so this is also available over SPI.
Hi Alexandre, On Wed, Feb 10, 2021 at 3:17 PM Alexandre Belloni <alexandre.belloni@bootlin.com> wrote: > On 10/02/2021 14:53:01+0100, Geert Uytterhoeven wrote: > > On Wed, Feb 10, 2021 at 2:45 PM Lars Povlsen <lars.povlsen@microchip.com> wrote: > > > Geert Uytterhoeven writes: > > > > the Microsemi/Microchip Serial GPIO device is present only Microsemi > > > > VCore III and Microchip Sparx5 SoCs. Hence add a dependency on > > > > ARCH_SPARX5 || SOC_VCOREIII, to prevent asking the user about this > > > > driver when configuring a kernel without support for these SoCs. > > > > > > > > Fixes: 7e5ea974e61c8dd0 ("pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO") > > > > Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> > > > > --- > > > > drivers/pinctrl/Kconfig | 4 ++-- > > > > 1 file changed, 2 insertions(+), 2 deletions(-) > > > > > > > > diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig > > > > index 113073d5f89bbf70..3b75b1d7d3d1f1b0 100644 > > > > --- a/drivers/pinctrl/Kconfig > > > > +++ b/drivers/pinctrl/Kconfig > > > > @@ -353,8 +353,8 @@ config PINCTRL_OCELOT > > > > > > > > config PINCTRL_MICROCHIP_SGPIO > > > > bool "Pinctrl driver for Microsemi/Microchip Serial GPIO" > > > > - depends on OF > > > > - depends on HAS_IOMEM > > > > + depends on OF && HAS_IOMEM > > > > + depends on ARCH_SPARX5 || SOC_VCOREIII || COMPILE_TEST > > > > select GPIOLIB > > > > select GPIOLIB_IRQCHIP > > > > select GENERIC_PINCONF > > > > > > Thank you for your patch. Unfortunately, it makes it impossible to use > > > the driver across PCIe - which is a specifically desired configuration. > > > > > > Could you add CONFIG_PCI to the || chain? > > > > Sure. > > > > Is PCIe the only other transport over which the register can be accessed? > > Or can this also be done over e.g. SPI, like on Ocelot[1]? > > > > [1] https://lore.kernel.org/linux-gpio/20200511145329.GV34497@piout.net/ > > > > Yes, this driver IP is also available on Ocelot (this is SOC_VCOREIII) > so this is also available over SPI. Hence would you consider depends on ARCH_SPARX5 || SOC_VCOREIII || PCI || SPI || COMPILE_TEST acceptable? Or would that be futile, as must systems have PCI and/or SPI enabled anyway? Gr{oetje,eeting}s, Geert
Geert Uytterhoeven writes: > Hi Alexandre, > > On Wed, Feb 10, 2021 at 3:17 PM Alexandre Belloni > <alexandre.belloni@bootlin.com> wrote: >> On 10/02/2021 14:53:01+0100, Geert Uytterhoeven wrote: >> > On Wed, Feb 10, 2021 at 2:45 PM Lars Povlsen <lars.povlsen@microchip.com> wrote: >> > > Geert Uytterhoeven writes: >> > > > the Microsemi/Microchip Serial GPIO device is present only Microsemi >> > > > VCore III and Microchip Sparx5 SoCs. Hence add a dependency on >> > > > ARCH_SPARX5 || SOC_VCOREIII, to prevent asking the user about this >> > > > driver when configuring a kernel without support for these SoCs. >> > > > >> > > > Fixes: 7e5ea974e61c8dd0 ("pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO") >> > > > Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> >> > > > --- >> > > > drivers/pinctrl/Kconfig | 4 ++-- >> > > > 1 file changed, 2 insertions(+), 2 deletions(-) >> > > > >> > > > diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig >> > > > index 113073d5f89bbf70..3b75b1d7d3d1f1b0 100644 >> > > > --- a/drivers/pinctrl/Kconfig >> > > > +++ b/drivers/pinctrl/Kconfig >> > > > @@ -353,8 +353,8 @@ config PINCTRL_OCELOT >> > > > >> > > > config PINCTRL_MICROCHIP_SGPIO >> > > > bool "Pinctrl driver for Microsemi/Microchip Serial GPIO" >> > > > - depends on OF >> > > > - depends on HAS_IOMEM >> > > > + depends on OF && HAS_IOMEM >> > > > + depends on ARCH_SPARX5 || SOC_VCOREIII || COMPILE_TEST >> > > > select GPIOLIB >> > > > select GPIOLIB_IRQCHIP >> > > > select GENERIC_PINCONF >> > > >> > > Thank you for your patch. Unfortunately, it makes it impossible to use >> > > the driver across PCIe - which is a specifically desired configuration. >> > > >> > > Could you add CONFIG_PCI to the || chain? >> > >> > Sure. >> > >> > Is PCIe the only other transport over which the register can be accessed? >> > Or can this also be done over e.g. SPI, like on Ocelot[1]? >> > >> > [1] https://lore.kernel.org/linux-gpio/20200511145329.GV34497@piout.net/ >> > >> >> Yes, this driver IP is also available on Ocelot (this is SOC_VCOREIII) >> so this is also available over SPI. > > Hence would you consider > > depends on ARCH_SPARX5 || SOC_VCOREIII || PCI || SPI || COMPILE_TEST > > acceptable? Or would that be futile, as must systems have PCI and/or > SPI enabled anyway? > > Gr{oetje,eeting}s, > > Geert Yes, that would be fine, but as you say - not have a lot of impact. Up to you... ---Lars
Hi Lars, On Wed, Feb 10, 2021 at 3:24 PM Lars Povlsen <lars.povlsen@microchip.com> wrote: > Geert Uytterhoeven writes: > > On Wed, Feb 10, 2021 at 3:17 PM Alexandre Belloni > > <alexandre.belloni@bootlin.com> wrote: > >> On 10/02/2021 14:53:01+0100, Geert Uytterhoeven wrote: > >> > On Wed, Feb 10, 2021 at 2:45 PM Lars Povlsen <lars.povlsen@microchip.com> wrote: > >> > > Geert Uytterhoeven writes: > >> > > > the Microsemi/Microchip Serial GPIO device is present only Microsemi > >> > > > VCore III and Microchip Sparx5 SoCs. Hence add a dependency on > >> > > > ARCH_SPARX5 || SOC_VCOREIII, to prevent asking the user about this > >> > > > driver when configuring a kernel without support for these SoCs. > >> > > > > >> > > > Fixes: 7e5ea974e61c8dd0 ("pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO") > >> > > > Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> > >> > > > --- > >> > > > drivers/pinctrl/Kconfig | 4 ++-- > >> > > > 1 file changed, 2 insertions(+), 2 deletions(-) > >> > > > > >> > > > diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig > >> > > > index 113073d5f89bbf70..3b75b1d7d3d1f1b0 100644 > >> > > > --- a/drivers/pinctrl/Kconfig > >> > > > +++ b/drivers/pinctrl/Kconfig > >> > > > @@ -353,8 +353,8 @@ config PINCTRL_OCELOT > >> > > > > >> > > > config PINCTRL_MICROCHIP_SGPIO > >> > > > bool "Pinctrl driver for Microsemi/Microchip Serial GPIO" > >> > > > - depends on OF > >> > > > - depends on HAS_IOMEM > >> > > > + depends on OF && HAS_IOMEM > >> > > > + depends on ARCH_SPARX5 || SOC_VCOREIII || COMPILE_TEST > >> > > > select GPIOLIB > >> > > > select GPIOLIB_IRQCHIP > >> > > > select GENERIC_PINCONF > >> > > > >> > > Thank you for your patch. Unfortunately, it makes it impossible to use > >> > > the driver across PCIe - which is a specifically desired configuration. > >> > > > >> > > Could you add CONFIG_PCI to the || chain? > >> > > >> > Sure. > >> > > >> > Is PCIe the only other transport over which the register can be accessed? > >> > Or can this also be done over e.g. SPI, like on Ocelot[1]? > >> > > >> > [1] https://lore.kernel.org/linux-gpio/20200511145329.GV34497@piout.net/ > >> > > >> > >> Yes, this driver IP is also available on Ocelot (this is SOC_VCOREIII) > >> so this is also available over SPI. > > > > Hence would you consider > > > > depends on ARCH_SPARX5 || SOC_VCOREIII || PCI || SPI || COMPILE_TEST > > > > acceptable? Or would that be futile, as must systems have PCI and/or > > SPI enabled anyway? > > > > Gr{oetje,eeting}s, > > > > Geert > > Yes, that would be fine, but as you say - not have a lot of impact. > > Up to you... OK, I'll drop this. Gr{oetje,eeting}s, Geert
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index 113073d5f89bbf70..3b75b1d7d3d1f1b0 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -353,8 +353,8 @@ config PINCTRL_OCELOT config PINCTRL_MICROCHIP_SGPIO bool "Pinctrl driver for Microsemi/Microchip Serial GPIO" - depends on OF - depends on HAS_IOMEM + depends on OF && HAS_IOMEM + depends on ARCH_SPARX5 || SOC_VCOREIII || COMPILE_TEST select GPIOLIB select GPIOLIB_IRQCHIP select GENERIC_PINCONF
the Microsemi/Microchip Serial GPIO device is present only Microsemi VCore III and Microchip Sparx5 SoCs. Hence add a dependency on ARCH_SPARX5 || SOC_VCOREIII, to prevent asking the user about this driver when configuring a kernel without support for these SoCs. Fixes: 7e5ea974e61c8dd0 ("pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> --- drivers/pinctrl/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)