@@ -26,7 +26,8 @@
#include "gpio-utils.h"
int monitor_device(const char *device_name,
- unsigned int line,
+ unsigned int *lines,
+ unsigned int num_lines,
struct gpioline_config *config,
unsigned int loops)
{
@@ -47,7 +48,7 @@ int monitor_device(const char *device_name,
goto exit_free_name;
}
- ret = gpiotools_request_line(device_name, &line, 1, config,
+ ret = gpiotools_request_line(device_name, lines, num_lines, config,
"gpio-event-mon");
if (ret < 0)
goto exit_device_close;
@@ -63,9 +64,23 @@ int monitor_device(const char *device_name,
goto exit_line_close;
}
- fprintf(stdout, "Monitoring line %d on %s\n", line, device_name);
- fprintf(stdout, "Initial line value: %d\n",
- gpiotools_test_bit(values.bits, 0));
+ if (num_lines == 1) {
+ fprintf(stdout, "Monitoring line %d on %s\n", lines[0], device_name);
+ fprintf(stdout, "Initial line value: %d\n",
+ gpiotools_test_bit(values.bits, 0));
+ } else {
+ fprintf(stdout, "Monitoring lines %d", lines[0]);
+ for (i = 1; i < num_lines - 1; i++)
+ fprintf(stdout, ", %d", lines[i]);
+ fprintf(stdout, " and %d on %s\n", lines[i], device_name);
+ fprintf(stdout, "Initial line values: %d",
+ gpiotools_test_bit(values.bits, 0));
+ for (i = 1; i < num_lines - 1; i++)
+ fprintf(stdout, ", %d",
+ gpiotools_test_bit(values.bits, i));
+ fprintf(stdout, " and %d\n",
+ gpiotools_test_bit(values.bits, i));
+ }
while (1) {
struct gpioline_event event;
@@ -124,7 +139,7 @@ void print_usage(void)
fprintf(stderr, "Usage: gpio-event-mon [options]...\n"
"Listen to events on GPIO lines, 0->1 1->0\n"
" -n <name> Listen on GPIOs on a named device (must be stated)\n"
- " -o <n> Offset to monitor\n"
+ " -o <n> Offset of line to monitor (may be repeated)\n"
" -d Set line as open drain\n"
" -s Set line as open source\n"
" -r Listen for rising edges\n"
@@ -145,7 +160,8 @@ void print_usage(void)
int main(int argc, char **argv)
{
const char *device_name = NULL;
- unsigned int line = -1;
+ unsigned int lines[GPIOLINES_MAX];
+ unsigned int num_lines = 0;
unsigned int loops = 0;
struct gpioline_config config;
int c, attr;
@@ -161,7 +177,12 @@ int main(int argc, char **argv)
device_name = optarg;
break;
case 'o':
- line = strtoul(optarg, NULL, 10);
+ if (num_lines >= GPIOLINES_MAX) {
+ print_usage();
+ return -1;
+ }
+ lines[num_lines] = strtoul(optarg, NULL, 10);
+ num_lines++;
break;
case 'b':
attr = config.num_attrs;
@@ -189,7 +210,7 @@ int main(int argc, char **argv)
}
}
- if (!device_name || line == -1) {
+ if (!device_name || num_lines == 0) {
print_usage();
return -1;
}
@@ -198,5 +219,5 @@ int main(int argc, char **argv)
"falling edges\n");
config.flags |= EDGE_FLAGS;
}
- return monitor_device(device_name, line, &config, loops);
+ return monitor_device(device_name, lines, num_lines, &config, loops);
}
Extend gpio-event-mon to support monitoring multiple lines. This would require multiple lineevent requests to implement using uAPI v1, but can be performed with a single line request using uAPI v2. Signed-off-by: Kent Gibson <warthog618@gmail.com> --- tools/gpio/gpio-event-mon.c | 41 ++++++++++++++++++++++++++++--------- 1 file changed, 31 insertions(+), 10 deletions(-)