diff mbox

[1/2] gpio: mmio: add support for NI 169445 NAND GPIO

Message ID 1488830761-681-2-git-send-email-nathan.sullivan@ni.com
State New
Headers show

Commit Message

Nathan Sullivan March 6, 2017, 8:06 p.m. UTC 
The GPIO-based NAND controller on National Instruments 169445 hardware
exposes a set of simple lines for the control signals.

Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
---
 .../bindings/gpio/ni,169445-nand-gpio.txt          | 36 ++++++++++++++++++++++
 drivers/gpio/gpio-mmio.c                           |  1 +
 2 files changed, 37 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt

Comments

Linus Walleij March 15, 2017, 9:33 a.m. UTC | #1 
On Mon, Mar 6, 2017 at 9:06 PM, Nathan Sullivan <nathan.sullivan@ni.com> wrote:

> The GPIO-based NAND controller on National Instruments 169445 hardware
> exposes a set of simple lines for the control signals.
>
> Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>

Totally standard ans simple patch, applied.

Hint: it's probably nice to use the gpio-line-names attribute
on these boards to name the lines.

Yours,
Linus Walleij
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt b/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
new file mode 100644
index 0000000..ca2c14f
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
@@ -0,0 +1,36 @@ 
+Bindings for the National Instruments 169445 GPIO NAND controller
+
+The 169445 GPIO NAND controller has two memory mapped GPIO registers, one
+for input (the ready signal) and one for output (control signals).  It is
+intended to be used with the GPIO NAND driver.
+
+Required properties:
+	- compatible: should be "ni,169445-nand-gpio"
+	- reg-names: must contain
+		"dat" - data register
+	- reg: address + size pairs describing the GPIO register sets;
+		order must correspond with the order of entries in reg-names
+	- #gpio-cells: must be set to 2. The first cell is the pin number and
+			the second cell is used to specify the gpio polarity:
+			0 = active high
+			1 = active low
+	- gpio-controller: Marks the device node as a gpio controller.
+
+Examples:
+	gpio1: nand-gpio-out@1f300010 {
+		compatible = "ni,169445-nand-gpio";
+		reg = <0x1f300010 0x4>;
+		reg-names = "dat";
+		gpio-controller;
+		#gpio-cells = <2>;
+		ngpios = <5>;
+	};
+
+	gpio2: nand-gpio-in@1f300014 {
+		compatible = "ni,169445-nand-gpio";
+		reg = <0x1f300014 0x4>;
+		reg-names = "dat";
+		gpio-controller;
+		#gpio-cells = <2>;
+		ngpios = <1>;
+	};
diff --git a/drivers/gpio/gpio-mmio.c b/drivers/gpio/gpio-mmio.c
index d7d03ad..f7da40e 100644
--- a/drivers/gpio/gpio-mmio.c
+++ b/drivers/gpio/gpio-mmio.c
@@ -575,6 +575,7 @@  static void __iomem *bgpio_map(struct platform_device *pdev,
 static const struct of_device_id bgpio_of_match[] = {
 	{ .compatible = "brcm,bcm6345-gpio" },
 	{ .compatible = "wd,mbl-gpio" },
+	{ .compatible = "ni,169445-nand-gpio" },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, bgpio_of_match);