diff mbox series

[v9,2/3] dt-bindings: hwmon: Support Aspeed g6 PWM TACH Control

Message ID 20230918064111.2221594-3-billy_tsai@aspeedtech.com
State Handled Elsewhere, archived
Headers show
Series Support pwm/tach driver for aspeed ast26xx | expand

Commit Message

Billy Tsai Sept. 18, 2023, 6:41 a.m. UTC
Document the compatible for aspeed,ast2600-pwm-tach device, which can
support up to 16 PWM outputs and 16 fan tach input.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
---
 .../bindings/hwmon/aspeed,g6-pwm-tach.yaml    | 69 +++++++++++++++++++
 1 file changed, 69 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml

Comments

Rob Herring (Arm) Oct. 2, 2023, 3:28 p.m. UTC | #1
On Mon, Sep 18, 2023 at 02:41:10PM +0800, Billy Tsai wrote:
> Document the compatible for aspeed,ast2600-pwm-tach device, which can
> support up to 16 PWM outputs and 16 fan tach input.
> 
> Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
> ---
>  .../bindings/hwmon/aspeed,g6-pwm-tach.yaml    | 69 +++++++++++++++++++
>  1 file changed, 69 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml
> 
> diff --git a/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml b/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml
> new file mode 100644
> index 000000000000..5a679f4ad2fa
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml
> @@ -0,0 +1,69 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +# Copyright (C) 2023 Aspeed, Inc.
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/hwmon/aspeed,g6-pwm-tach.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: ASPEED G6 PWM and Fan Tach controller device driver

This is binding for the h/w, not a 'device driver'.

> +
> +maintainers:
> +  - Billy Tsai <billy_tsai@aspeedtech.com>
> +
> +description: |
> +  The ASPEED PWM controller can support up to 16 PWM outputs.
> +  The ASPEED Fan Tacho controller can support up to 16 fan tach input.
> +  They are independent hardware blocks, which are different from the
> +  previous version of the ASPEED chip.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - aspeed,ast2600-pwm-tach
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  resets:
> +    maxItems: 1
> +
> +  "#pwm-cells":
> +    const: 3
> +
> +patternProperties:
> +  "^fan-[0-9a-f]+$":

foo-<index> naming is decimal, not hex. (unit-addresses are hex)

But if 0 and 1 correspond to something in the h/w, then you should 
probably be using 'reg' instead (which means a unit-address too).

> +    $ref: fan-common.yaml#
> +    unevaluatedProperties: false
> +    required:
> +      - tach-ch
> +
> +required:
> +  - reg
> +  - clocks
> +  - resets
> +  - "#pwm-cells"
> +  - compatible
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/aspeed-clock.h>
> +    pwm_tach: pwm-tach-controller@1e610000 {
> +      compatible = "aspeed,ast2600-pwm-tach";
> +      reg = <0x1e610000 0x100>;
> +      clocks = <&syscon ASPEED_CLK_AHB>;
> +      resets = <&syscon ASPEED_RESET_PWM>;
> +      #pwm-cells = <3>;
> +
> +      fan-0 {
> +        tach-ch = /bits/ 8 <0x0>;

What about the PWM connection?

> +      };
> +
> +      fan-1 {
> +        tach-ch = /bits/ 8 <0x1 0x2>;
> +      };
> +    };
> -- 
> 2.25.1
>
Billy Tsai Oct. 5, 2023, 1:26 a.m. UTC | #2
>> Document the compatible for aspeed,ast2600-pwm-tach device, which can
>> support up to 16 PWM outputs and 16 fan tach input.
>>
>> Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
>> ---
>>  .../bindings/hwmon/aspeed,g6-pwm-tach.yaml    | 69 +++++++++++++++++++
>>  1 file changed, 69 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml b/Documentation/devicetree/>bindings/hwmon/aspeed,g6-pwm-tach.yaml
>> new file mode 100644
>> index 000000000000..5a679f4ad2fa
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml
>> @@ -0,0 +1,69 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +# Copyright (C) 2023 Aspeed, Inc.
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/hwmon/aspeed,g6-pwm-tach.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: ASPEED G6 PWM and Fan Tach controller device driver

> This is binding for the h/w, not a 'device driver'.

Okay, I will remove the 'device driver'.

>> +
>> +maintainers:
>> +  - Billy Tsai <billy_tsai@aspeedtech.com>
>> +
>> +description: |
>> +  The ASPEED PWM controller can support up to 16 PWM outputs.
>> +  The ASPEED Fan Tacho controller can support up to 16 fan tach input.
>> +  They are independent hardware blocks, which are different from the
>> +  previous version of the ASPEED chip.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - aspeed,ast2600-pwm-tach
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  clocks:
>> +    maxItems: 1
>> +
>> +  resets:
>> +    maxItems: 1
>> +
>> +  "#pwm-cells":
>> +    const: 3
>> +
>> +patternProperties:
>> +  "^fan-[0-9a-f]+$":

> foo-<index> naming is decimal, not hex. (unit-addresses are hex)

Okay, I will change it to the decimal.

> But if 0 and 1 correspond to something in the h/w, then you should
> probably be using 'reg' instead (which means a unit-address too).

The number doesn't unrelate to the hardware.

>> +    $ref: fan-common.yaml#
>> +    unevaluatedProperties: false
>> +    required:
>> +      - tach-ch
>> +
>> +required:
>> +  - reg
>> +  - clocks
>> +  - resets
>> +  - "#pwm-cells"
>> +  - compatible
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> +  - |
>> +    #include <dt-bindings/clock/aspeed-clock.h>
>> +    pwm_tach: pwm-tach-controller@1e610000 {
>> +      compatible = "aspeed,ast2600-pwm-tach";
>> +      reg = <0x1e610000 0x100>;
>> +      clocks = <&syscon ASPEED_CLK_AHB>;
>> +      resets = <&syscon ASPEED_RESET_PWM>;
>> +      #pwm-cells = <3>;
>> +
>> +      fan-0 {
>> +        tach-ch = /bits/ 8 <0x0>;

> What about the PWM connection?

I only want to create the fan monitor without fan control.
So, the PWM connection is unnecessary.

Thanks

>> +      };
>> +
>> +      fan-1 {
>> +        tach-ch = /bits/ 8 <0x1 0x2>;
>> +      };
>> +    };
>> --
>> 2.25.1
>>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml b/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml
new file mode 100644
index 000000000000..5a679f4ad2fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml
@@ -0,0 +1,69 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2023 Aspeed, Inc.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/hwmon/aspeed,g6-pwm-tach.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ASPEED G6 PWM and Fan Tach controller device driver
+
+maintainers:
+  - Billy Tsai <billy_tsai@aspeedtech.com>
+
+description: |
+  The ASPEED PWM controller can support up to 16 PWM outputs.
+  The ASPEED Fan Tacho controller can support up to 16 fan tach input.
+  They are independent hardware blocks, which are different from the
+  previous version of the ASPEED chip.
+
+properties:
+  compatible:
+    enum:
+      - aspeed,ast2600-pwm-tach
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  "#pwm-cells":
+    const: 3
+
+patternProperties:
+  "^fan-[0-9a-f]+$":
+    $ref: fan-common.yaml#
+    unevaluatedProperties: false
+    required:
+      - tach-ch
+
+required:
+  - reg
+  - clocks
+  - resets
+  - "#pwm-cells"
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/aspeed-clock.h>
+    pwm_tach: pwm-tach-controller@1e610000 {
+      compatible = "aspeed,ast2600-pwm-tach";
+      reg = <0x1e610000 0x100>;
+      clocks = <&syscon ASPEED_CLK_AHB>;
+      resets = <&syscon ASPEED_RESET_PWM>;
+      #pwm-cells = <3>;
+
+      fan-0 {
+        tach-ch = /bits/ 8 <0x0>;
+      };
+
+      fan-1 {
+        tach-ch = /bits/ 8 <0x1 0x2>;
+      };
+    };