@@ -90,6 +90,9 @@ struct ftgmac100 {
struct mii_bus *mii_bus;
struct clk *clk;
+ /* AST2500/AST2600 RMII ref clock gate */
+ struct clk *rclk;
+
/* Link management */
int cur_speed;
int cur_duplex;
@@ -1718,20 +1721,41 @@ static void ftgmac100_ncsi_handler(struct ncsi_dev *nd)
nd->link_up ? "up" : "down");
}
-static void ftgmac100_setup_clk(struct ftgmac100 *priv)
+static int ftgmac100_setup_clk(struct ftgmac100 *priv)
{
- priv->clk = devm_clk_get(priv->dev, NULL);
- if (IS_ERR(priv->clk))
- return;
+ struct clk *clk;
+ int rc;
- clk_prepare_enable(priv->clk);
+ clk = devm_clk_get(priv->dev, NULL /* MACCLK */);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+ priv->clk = clk;
+ rc = clk_prepare_enable(priv->clk);
+ if (rc)
+ return rc;
/* Aspeed specifies a 100MHz clock is required for up to
* 1000Mbit link speeds. As NCSI is limited to 100Mbit, 25MHz
* is sufficient
*/
- clk_set_rate(priv->clk, priv->use_ncsi ? FTGMAC_25MHZ :
- FTGMAC_100MHZ);
+ rc = clk_set_rate(priv->clk, priv->use_ncsi ? FTGMAC_25MHZ :
+ FTGMAC_100MHZ);
+ if (rc)
+ goto cleanup_clk;
+
+ /* RCLK is for RMII, typically used for NCSI. Optional because its not
+ * necessary if it's the AST2400 MAC, or the MAC is configured for
+ * RGMII, or the controller is not an ASPEED-based controller.
+ */
+ priv->rclk = devm_clk_get_optional(priv->dev, "RCLK");
+ rc = clk_prepare_enable(priv->rclk);
+ if (!rc)
+ return 0;
+
+cleanup_clk:
+ clk_disable_unprepare(priv->clk);
+
+ return rc;
}
static int ftgmac100_probe(struct platform_device *pdev)
@@ -1853,8 +1877,11 @@ static int ftgmac100_probe(struct platform_device *pdev)
goto err_setup_mdio;
}
- if (priv->is_aspeed)
- ftgmac100_setup_clk(priv);
+ if (priv->is_aspeed) {
+ err = ftgmac100_setup_clk(priv);
+ if (err)
+ goto err_ncsi_dev;
+ }
/* Default ring sizes */
priv->rx_q_entries = priv->new_rx_q_entries = DEF_RX_QUEUE_ENTRIES;
@@ -1886,8 +1913,10 @@ static int ftgmac100_probe(struct platform_device *pdev)
return 0;
-err_ncsi_dev:
err_register_netdev:
+ clk_disable_unprepare(priv->rclk);
+ clk_disable_unprepare(priv->clk);
+err_ncsi_dev:
ftgmac100_destroy_mdio(netdev);
err_setup_mdio:
iounmap(priv->base);
@@ -1909,6 +1938,7 @@ static int ftgmac100_remove(struct platform_device *pdev)
unregister_netdev(netdev);
+ clk_disable_unprepare(priv->rclk);
clk_disable_unprepare(priv->clk);
/* There's a small chance the reset task will have been re-queued,
The 50MHz RCLK has to be enabled before the RMII interface will function. Signed-off-by: Andrew Jeffery <andrew@aj.id.au> --- v2: Mainly a rework of error case handling, some changes to comments drivers/net/ethernet/faraday/ftgmac100.c | 50 +++++++++++++++++++----- 1 file changed, 40 insertions(+), 10 deletions(-)