@@ -6614,13 +6614,6 @@ L: iommu@lists.linux-foundation.org
S: Maintained
F: drivers/iommu/exynos-iommu.c
-EZchip NPS platform support
-M: Vineet Gupta <vgupta@synopsys.com>
-M: Ofer Levi <oferle@nvidia.com>
-S: Supported
-F: arch/arc/boot/dts/eznps.dts
-F: arch/arc/plat-eznps
-
F2FS FILE SYSTEM
M: Jaegeuk Kim <jaegeuk@kernel.org>
M: Chao Yu <yuchao0@huawei.com>
@@ -94,13 +94,8 @@ core-y += arch/arc/boot/dts/
core-y += arch/arc/plat-sim/
core-$(CONFIG_ARC_PLAT_TB10X) += arch/arc/plat-tb10x/
core-$(CONFIG_ARC_PLAT_AXS10X) += arch/arc/plat-axs10x/
-core-$(CONFIG_ARC_PLAT_EZNPS) += arch/arc/plat-eznps/
core-$(CONFIG_ARC_SOC_HSDK) += arch/arc/plat-hsdk/
-ifdef CONFIG_ARC_PLAT_EZNPS
-KBUILD_CPPFLAGS += -I$(srctree)/arch/arc/plat-eznps/include
-endif
-
drivers-$(CONFIG_OPROFILE) += arch/arc/oprofile/
libs-y += arch/arc/lib/ $(LIBGCC)
deleted file mode 100644
@@ -1,80 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_NO_HZ_IDLE=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3=y
-# CONFIG_EPOLL is not set
-# CONFIG_SIGNALFD is not set
-# CONFIG_TIMERFD is not set
-# CONFIG_EVENTFD is not set
-# CONFIG_AIO is not set
-CONFIG_EMBEDDED=y
-CONFIG_PERF_EVENTS=y
-# CONFIG_COMPAT_BRK is not set
-CONFIG_ISA_ARCOMPACT=y
-CONFIG_KPROBES=y
-CONFIG_MODULES=y
-CONFIG_MODULE_FORCE_LOAD=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_ARC_PLAT_EZNPS=y
-CONFIG_SMP=y
-CONFIG_NR_CPUS=4096
-CONFIG_ARC_CACHE_LINE_SHIFT=5
-# CONFIG_ARC_CACHE_PAGES is not set
-# CONFIG_ARC_HAS_LLSC is not set
-CONFIG_ARC_KVADDR_SIZE=402
-CONFIG_ARC_EMUL_UNALIGNED=y
-CONFIG_PREEMPT=y
-CONFIG_NET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_COUNT=1
-CONFIG_BLK_DEV_RAM_SIZE=2048
-CONFIG_NETDEVICES=y
-CONFIG_NETCONSOLE=y
-# CONFIG_NET_VENDOR_BROADCOM is not set
-# CONFIG_NET_VENDOR_MICREL is not set
-# CONFIG_NET_VENDOR_STMICRO is not set
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV is not set
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=1
-CONFIG_SERIAL_8250_RUNTIME_UARTS=1
-CONFIG_SERIAL_8250_DW=y
-CONFIG_SERIAL_OF_PLATFORM=y
-# CONFIG_HW_RANDOM is not set
-# CONFIG_HWMON is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_DNOTIFY is not set
-CONFIG_PROC_KCORE=y
-CONFIG_TMPFS=y
-# CONFIG_MISC_FILESYSTEMS is not set
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_ROOT_NFS=y
-CONFIG_DEBUG_INFO=y
-# CONFIG_ENABLE_MUST_CHECK is not set
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_MEMORY_INIT=y
-CONFIG_ENABLE_DEFAULT_TRACERS=y
@@ -14,8 +14,6 @@
#include <asm/barrier.h>
#include <asm/smp.h>
-#ifndef CONFIG_ARC_PLAT_EZNPS
-
#define atomic_read(v) READ_ONCE((v)->counter)
#ifdef CONFIG_ARC_HAS_LLSC
@@ -195,108 +193,6 @@ ATOMIC_OPS(andnot, &= ~, bic)
ATOMIC_OPS(or, |=, or)
ATOMIC_OPS(xor, ^=, xor)
-#else /* CONFIG_ARC_PLAT_EZNPS */
-
-static inline int atomic_read(const atomic_t *v)
-{
- int temp;
-
- __asm__ __volatile__(
- " ld.di %0, [%1]"
- : "=r"(temp)
- : "r"(&v->counter)
- : "memory");
- return temp;
-}
-
-static inline void atomic_set(atomic_t *v, int i)
-{
- __asm__ __volatile__(
- " st.di %0,[%1]"
- :
- : "r"(i), "r"(&v->counter)
- : "memory");
-}
-
-#define ATOMIC_OP(op, c_op, asm_op) \
-static inline void atomic_##op(int i, atomic_t *v) \
-{ \
- __asm__ __volatile__( \
- " mov r2, %0\n" \
- " mov r3, %1\n" \
- " .word %2\n" \
- : \
- : "r"(i), "r"(&v->counter), "i"(asm_op) \
- : "r2", "r3", "memory"); \
-} \
-
-#define ATOMIC_OP_RETURN(op, c_op, asm_op) \
-static inline int atomic_##op##_return(int i, atomic_t *v) \
-{ \
- unsigned int temp = i; \
- \
- /* Explicit full memory barrier needed before/after */ \
- smp_mb(); \
- \
- __asm__ __volatile__( \
- " mov r2, %0\n" \
- " mov r3, %1\n" \
- " .word %2\n" \
- " mov %0, r2" \
- : "+r"(temp) \
- : "r"(&v->counter), "i"(asm_op) \
- : "r2", "r3", "memory"); \
- \
- smp_mb(); \
- \
- temp c_op i; \
- \
- return temp; \
-}
-
-#define ATOMIC_FETCH_OP(op, c_op, asm_op) \
-static inline int atomic_fetch_##op(int i, atomic_t *v) \
-{ \
- unsigned int temp = i; \
- \
- /* Explicit full memory barrier needed before/after */ \
- smp_mb(); \
- \
- __asm__ __volatile__( \
- " mov r2, %0\n" \
- " mov r3, %1\n" \
- " .word %2\n" \
- " mov %0, r2" \
- : "+r"(temp) \
- : "r"(&v->counter), "i"(asm_op) \
- : "r2", "r3", "memory"); \
- \
- smp_mb(); \
- \
- return temp; \
-}
-
-#define ATOMIC_OPS(op, c_op, asm_op) \
- ATOMIC_OP(op, c_op, asm_op) \
- ATOMIC_OP_RETURN(op, c_op, asm_op) \
- ATOMIC_FETCH_OP(op, c_op, asm_op)
-
-ATOMIC_OPS(add, +=, CTOP_INST_AADD_DI_R2_R2_R3)
-#define atomic_sub(i, v) atomic_add(-(i), (v))
-#define atomic_sub_return(i, v) atomic_add_return(-(i), (v))
-#define atomic_fetch_sub(i, v) atomic_fetch_add(-(i), (v))
-
-#undef ATOMIC_OPS
-#define ATOMIC_OPS(op, c_op, asm_op) \
- ATOMIC_OP(op, c_op, asm_op) \
- ATOMIC_FETCH_OP(op, c_op, asm_op)
-
-ATOMIC_OPS(and, &=, CTOP_INST_AAND_DI_R2_R2_R3)
-ATOMIC_OPS(or, |=, CTOP_INST_AOR_DI_R2_R2_R3)
-ATOMIC_OPS(xor, ^=, CTOP_INST_AXOR_DI_R2_R2_R3)
-
-#endif /* CONFIG_ARC_PLAT_EZNPS */
-
#undef ATOMIC_OPS
#undef ATOMIC_FETCH_OP
#undef ATOMIC_OP_RETURN
@@ -27,7 +27,7 @@
#define rmb() asm volatile("dmb 1\n" : : : "memory")
#define wmb() asm volatile("dmb 2\n" : : : "memory")
-#elif !defined(CONFIG_ARC_PLAT_EZNPS) /* CONFIG_ISA_ARCOMPACT */
+#else
/*
* ARCompact based cores (ARC700) only have SYNC instruction which is super
@@ -37,13 +37,6 @@
#define mb() asm volatile("sync\n" : : : "memory")
-#else /* CONFIG_ARC_PLAT_EZNPS */
-
-#include <plat/ctop.h>
-
-#define mb() asm volatile (".word %0" : : "i"(CTOP_INST_SCHD_RW) : "memory")
-#define rmb() asm volatile (".word %0" : : "i"(CTOP_INST_SCHD_RD) : "memory")
-
#endif
#include <asm-generic/barrier.h>
@@ -85,7 +85,7 @@ static inline int test_and_##op##_bit(unsigned long nr, volatile unsigned long *
return (old & (1 << nr)) != 0; \
}
-#elif !defined(CONFIG_ARC_PLAT_EZNPS)
+#else /* !CONFIG_ARC_HAS_LLSC */
/*
* Non hardware assisted Atomic-R-M-W
@@ -136,55 +136,7 @@ static inline int test_and_##op##_bit(unsigned long nr, volatile unsigned long *
return (old & (1UL << (nr & 0x1f))) != 0; \
}
-#else /* CONFIG_ARC_PLAT_EZNPS */
-
-#define BIT_OP(op, c_op, asm_op) \
-static inline void op##_bit(unsigned long nr, volatile unsigned long *m)\
-{ \
- m += nr >> 5; \
- \
- nr = (1UL << (nr & 0x1f)); \
- if (asm_op == CTOP_INST_AAND_DI_R2_R2_R3) \
- nr = ~nr; \
- \
- __asm__ __volatile__( \
- " mov r2, %0\n" \
- " mov r3, %1\n" \
- " .word %2\n" \
- : \
- : "r"(nr), "r"(m), "i"(asm_op) \
- : "r2", "r3", "memory"); \
-}
-
-#define TEST_N_BIT_OP(op, c_op, asm_op) \
-static inline int test_and_##op##_bit(unsigned long nr, volatile unsigned long *m)\
-{ \
- unsigned long old; \
- \
- m += nr >> 5; \
- \
- nr = old = (1UL << (nr & 0x1f)); \
- if (asm_op == CTOP_INST_AAND_DI_R2_R2_R3) \
- old = ~old; \
- \
- /* Explicit full memory barrier needed before/after */ \
- smp_mb(); \
- \
- __asm__ __volatile__( \
- " mov r2, %0\n" \
- " mov r3, %1\n" \
- " .word %2\n" \
- " mov %0, r2" \
- : "+r"(old) \
- : "r"(m), "i"(asm_op) \
- : "r2", "r3", "memory"); \
- \
- smp_mb(); \
- \
- return (old & nr) != 0; \
-}
-
-#endif /* CONFIG_ARC_PLAT_EZNPS */
+#endif
/***************************************
* Non atomic variants
@@ -226,15 +178,9 @@ static inline int __test_and_##op##_bit(unsigned long nr, volatile unsigned long
/* __test_and_set_bit(), __test_and_clear_bit(), __test_and_change_bit() */\
__TEST_N_BIT_OP(op, c_op, asm_op)
-#ifndef CONFIG_ARC_PLAT_EZNPS
BIT_OPS(set, |, bset)
BIT_OPS(clear, & ~, bclr)
BIT_OPS(change, ^, bxor)
-#else
-BIT_OPS(set, |, CTOP_INST_AOR_DI_R2_R2_R3)
-BIT_OPS(clear, & ~, CTOP_INST_AAND_DI_R2_R2_R3)
-BIT_OPS(change, ^, CTOP_INST_AXOR_DI_R2_R2_R3)
-#endif
/*
* This routine doesn't need to be atomic.
@@ -41,7 +41,7 @@ __cmpxchg(volatile void *ptr, unsigned long expected, unsigned long new)
return prev;
}
-#elif !defined(CONFIG_ARC_PLAT_EZNPS)
+#else /* !CONFIG_ARC_HAS_LLSC */
static inline unsigned long
__cmpxchg(volatile void *ptr, unsigned long expected, unsigned long new)
@@ -61,33 +61,7 @@ __cmpxchg(volatile void *ptr, unsigned long expected, unsigned long new)
return prev;
}
-#else /* CONFIG_ARC_PLAT_EZNPS */
-
-static inline unsigned long
-__cmpxchg(volatile void *ptr, unsigned long expected, unsigned long new)
-{
- /*
- * Explicit full memory barrier needed before/after
- */
- smp_mb();
-
- write_aux_reg(CTOP_AUX_GPA1, expected);
-
- __asm__ __volatile__(
- " mov r2, %0\n"
- " mov r3, %1\n"
- " .word %2\n"
- " mov %0, r2"
- : "+r"(new)
- : "r"(ptr), "i"(CTOP_INST_EXC_DI_R2_R2_R3)
- : "r2", "r3", "memory");
-
- smp_mb();
-
- return new;
-}
-
-#endif /* CONFIG_ARC_HAS_LLSC */
+#endif
#define cmpxchg(ptr, o, n) ({ \
(typeof(*(ptr)))__cmpxchg((ptr), \
@@ -104,8 +78,6 @@ __cmpxchg(volatile void *ptr, unsigned long expected, unsigned long new)
#define atomic_cmpxchg(v, o, n) ((int)cmpxchg(&((v)->counter), (o), (n)))
-#ifndef CONFIG_ARC_PLAT_EZNPS
-
/*
* xchg (reg with memory) based on "Native atomic" EX insn
*/
@@ -168,44 +140,6 @@ static inline unsigned long __xchg(unsigned long val, volatile void *ptr,
#endif
-#else /* CONFIG_ARC_PLAT_EZNPS */
-
-static inline unsigned long __xchg(unsigned long val, volatile void *ptr,
- int size)
-{
- extern unsigned long __xchg_bad_pointer(void);
-
- switch (size) {
- case 4:
- /*
- * Explicit full memory barrier needed before/after
- */
- smp_mb();
-
- __asm__ __volatile__(
- " mov r2, %0\n"
- " mov r3, %1\n"
- " .word %2\n"
- " mov %0, r2\n"
- : "+r"(val)
- : "r"(ptr), "i"(CTOP_INST_XEX_DI_R2_R2_R3)
- : "r2", "r3", "memory");
-
- smp_mb();
-
- return val;
- }
- return __xchg_bad_pointer();
-}
-
-#define xchg(ptr, with) ({ \
- (typeof(*(ptr)))__xchg((unsigned long)(with), \
- (ptr), \
- sizeof(*(ptr))); \
-})
-
-#endif /* CONFIG_ARC_PLAT_EZNPS */
-
/*
* "atomic" variant of xchg()
* REQ: It needs to follow the same serialization rules as other atomic_xxx()
@@ -33,10 +33,6 @@
#include <asm/irqflags-compact.h>
#include <asm/thread_info.h> /* For THREAD_SIZE */
-#ifdef CONFIG_ARC_PLAT_EZNPS
-#include <plat/ctop.h>
-#endif
-
/*--------------------------------------------------------------
* Switch to Kernel Mode stack if SP points to User Mode stack
*
@@ -189,12 +185,6 @@
PUSHAX lp_start
PUSHAX erbta
-#ifdef CONFIG_ARC_PLAT_EZNPS
- .word CTOP_INST_SCHD_RW
- PUSHAX CTOP_AUX_GPA1
- PUSHAX CTOP_AUX_EFLAGS
-#endif
-
lr r10, [ecr]
st r10, [sp, PT_event] /* EV_Trap expects r10 to have ECR */
.endm
@@ -211,11 +201,6 @@
* by hardware and that is not good.
*-------------------------------------------------------------*/
.macro EXCEPTION_EPILOGUE
-#ifdef CONFIG_ARC_PLAT_EZNPS
- .word CTOP_INST_SCHD_RW
- POPAX CTOP_AUX_EFLAGS
- POPAX CTOP_AUX_GPA1
-#endif
POPAX erbta
POPAX lp_start
@@ -278,11 +263,6 @@
PUSHAX lp_start
PUSHAX bta_l\LVL\()
-#ifdef CONFIG_ARC_PLAT_EZNPS
- .word CTOP_INST_SCHD_RW
- PUSHAX CTOP_AUX_GPA1
- PUSHAX CTOP_AUX_EFLAGS
-#endif
.endm
/*--------------------------------------------------------------
@@ -295,11 +275,6 @@
* by hardware and that is not good.
*-------------------------------------------------------------*/
.macro INTERRUPT_EPILOGUE LVL
-#ifdef CONFIG_ARC_PLAT_EZNPS
- .word CTOP_INST_SCHD_RW
- POPAX CTOP_AUX_EFLAGS
- POPAX CTOP_AUX_GPA1
-#endif
POPAX bta_l\LVL\()
POPAX lp_start
@@ -327,13 +302,11 @@
bic \reg, sp, (THREAD_SIZE - 1)
.endm
-#ifndef CONFIG_ARC_PLAT_EZNPS
/* Get CPU-ID of this core */
.macro GET_CPU_ID reg
lr \reg, [identity]
lsr \reg, \reg, 8
bmsk \reg, \reg, 7
.endm
-#endif
#endif /* __ASM_ARC_ENTRY_COMPACT_H */
@@ -17,13 +17,6 @@
#include <asm/dsp.h>
#include <asm/fpu.h>
-#ifdef CONFIG_ARC_PLAT_EZNPS
-struct eznps_dp {
- unsigned int eflags;
- unsigned int gpa1;
-};
-#endif
-
/* Arch specific stuff which needs to be saved per task.
* However these items are not so important so as to earn a place in
* struct thread_info
@@ -38,9 +31,6 @@ struct thread_struct {
#ifdef CONFIG_ARC_FPU_SAVE_RESTORE
struct arc_fpu fpu;
#endif
-#ifdef CONFIG_ARC_PLAT_EZNPS
- struct eznps_dp dp;
-#endif
};
#define INIT_THREAD { \
@@ -60,17 +50,8 @@ struct task_struct;
* A lot of busy-wait loops in SMP are based off of non-volatile data otherwise
* get optimised away by gcc
*/
-#ifndef CONFIG_EZNPS_MTM_EXT
-
#define cpu_relax() barrier()
-#else
-
-#define cpu_relax() \
- __asm__ __volatile__ (".word %0" : : "i"(CTOP_INST_SCHD_RW) : "memory")
-
-#endif
-
#define KSTK_EIP(tsk) (task_pt_regs(tsk)->ret)
#define KSTK_ESP(tsk) (task_pt_regs(tsk)->sp)
@@ -118,25 +99,7 @@ extern unsigned int get_wchan(struct task_struct *p);
#define USER_KERNEL_GUTTER (VMALLOC_START - TASK_SIZE)
-#ifdef CONFIG_ARC_PLAT_EZNPS
-/* NPS architecture defines special window of 129M in user address space for
- * special memory areas, when accessing this window the MMU do not use TLB.
- * Instead MMU direct the access to:
- * 0x57f00000:0x57ffffff -- 1M of closely coupled memory (aka CMEM)
- * 0x58000000:0x5fffffff -- 16 huge pages, 8M each, with fixed map (aka FMTs)
- *
- * CMEM - is the fastest memory we got and its size is 16K.
- * FMT - is used to map either to internal/external memory.
- * Internal memory is the second fast memory and its size is 16M
- * External memory is the biggest memory (16G) and also the slowest.
- *
- * STACK_TOP need to be PMD align (21bit) that is why we supply 0x57e00000.
- */
-#define STACK_TOP 0x57e00000
-#else
#define STACK_TOP TASK_SIZE
-#endif
-
#define STACK_TOP_MAX STACK_TOP
/* This decides where the kernel will search for a free chunk of vm
@@ -16,11 +16,6 @@
#ifdef CONFIG_ISA_ARCOMPACT
struct pt_regs {
-#ifdef CONFIG_ARC_PLAT_EZNPS
- unsigned long eflags; /* Extended FLAGS */
- unsigned long gpa1; /* General Purpose Aux */
-#endif
-
/* Real registers */
unsigned long bta; /* bta_l1, bta_l2, erbta */
@@ -9,11 +9,7 @@
#include <linux/types.h>
#include <uapi/asm/setup.h>
-#ifdef CONFIG_ARC_PLAT_EZNPS
-#define COMMAND_LINE_SIZE 2048
-#else
#define COMMAND_LINE_SIZE 256
-#endif
/*
* Data structure to map a ID to string
@@ -232,15 +232,9 @@ static inline void arch_spin_lock(arch_spinlock_t *lock)
__asm__ __volatile__(
"1: ex %0, [%1] \n"
-#ifdef CONFIG_EZNPS_MTM_EXT
- " .word %3 \n"
-#endif
" breq %0, %2, 1b \n"
: "+&r" (val)
: "r"(&(lock->slock)), "ir"(__ARCH_SPIN_LOCK_LOCKED__)
-#ifdef CONFIG_EZNPS_MTM_EXT
- , "i"(CTOP_INST_SCHD_RW)
-#endif
: "memory");
smp_mb();
@@ -12,19 +12,10 @@
#include <asm/dsp-impl.h>
#include <asm/fpu.h>
-#ifdef CONFIG_ARC_PLAT_EZNPS
-extern void dp_save_restore(struct task_struct *p, struct task_struct *n);
-#define ARC_EZNPS_DP_PREV(p, n) dp_save_restore(p, n)
-#else
-#define ARC_EZNPS_DP_PREV(p, n)
-
-#endif /* !CONFIG_ARC_PLAT_EZNPS */
-
struct task_struct *__switch_to(struct task_struct *p, struct task_struct *n);
#define switch_to(prev, next, last) \
do { \
- ARC_EZNPS_DP_PREV(prev, next); \
dsp_save_restore(prev, next); \
fpu_save_restore(prev, next); \
last = __switch_to(prev, next);\
@@ -14,9 +14,6 @@
#include <asm/asm-offsets.h>
#include <linux/sched.h>
#include <linux/sched/debug.h>
-#ifdef CONFIG_ARC_PLAT_EZNPS
-#include <plat/ctop.h>
-#endif
#define KSP_WORD_OFF ((TASK_THREAD + THREAD_KSP) / 4)
@@ -67,17 +64,10 @@ __switch_to(struct task_struct *prev_task, struct task_struct *next_task)
*/
#ifndef CONFIG_SMP
"st %2, [@_current_task] \n\t"
-#else
-#ifdef CONFIG_ARC_PLAT_EZNPS
- "lr r24, [%4] \n\t"
-#ifndef CONFIG_EZNPS_MTM_EXT
- "lsr r24, r24, 4 \n\t"
-#endif
#else
"lr r24, [identity] \n\t"
"lsr r24, r24, 8 \n\t"
"bmsk r24, r24, 7 \n\t"
-#endif
"add2 r24, @_current_task, r24 \n\t"
"st %2, [r24] \n\t"
#endif
@@ -115,9 +105,6 @@ __switch_to(struct task_struct *prev_task, struct task_struct *next_task)
: "=r"(tmp)
: "n"(KSP_WORD_OFF), "r"(next), "r"(prev)
-#ifdef CONFIG_ARC_PLAT_EZNPS
- , "i"(CTOP_AUX_LOGIC_GLOBAL_ID)
-#endif
: "blink"
);
@@ -116,17 +116,6 @@ void arch_cpu_idle(void)
:"I"(arg)); /* can't be "r" has to be embedded const */
}
-#elif defined(CONFIG_EZNPS_MTM_EXT) /* ARC700 variant in NPS */
-
-void arch_cpu_idle(void)
-{
- /* only the calling HW thread needs to sleep */
- __asm__ __volatile__(
- ".word %0 \n"
- :
- :"i"(CTOP_INST_HWSCHD_WFT_IE12));
-}
-
#else /* ARC700 */
void arch_cpu_idle(void)
@@ -278,10 +267,6 @@ void start_thread(struct pt_regs *regs, unsigned long pc, unsigned long usp)
*/
regs->status32 = STATUS_U_MASK | STATUS_L_MASK | ISA_INIT_STATUS_BITS;
-#ifdef CONFIG_EZNPS_MTM_EXT
- regs->eflags = 0;
-#endif
-
fpu_init_task(regs);
/* bogus seed values for debugging */
@@ -281,13 +281,6 @@ ex_saved_reg1:
.macro COMMIT_ENTRY_TO_MMU
#if (CONFIG_ARC_MMU_VER < 4)
-#ifdef CONFIG_EZNPS_MTM_EXT
- /* verify if entry for this vaddr+ASID already exists */
- sr TLBProbe, [ARC_REG_TLBCOMMAND]
- lr r0, [ARC_REG_TLBINDEX]
- bbit0 r0, 31, 88f
-#endif
-
/* Get free TLB slot: Set = computed from vaddr, way = random */
sr TLBGetIndex, [ARC_REG_TLBCOMMAND]
deleted file mode 100644
@@ -1,58 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-#
-# For a description of the syntax of this configuration file,
-# see Documentation/kbuild/kconfig-language.rst.
-#
-
-menuconfig ARC_PLAT_EZNPS
- bool "\"EZchip\" ARC dev platform"
- depends on ISA_ARCOMPACT
- select CPU_BIG_ENDIAN
- select CLKSRC_NPS if !PHYS_ADDR_T_64BIT
- select EZNPS_GIC
- select EZCHIP_NPS_MANAGEMENT_ENET if ETHERNET
- help
- Support for EZchip development platforms,
- based on ARC700 cores.
- We handle few flavors:
- - Hardware Emulator AKA HE which is FPGA based chassis
- - Simulator based on MetaWare nSIM
- - NPS400 chip based on ASIC
-
-config EZNPS_MTM_EXT
- bool "ARC-EZchip MTM Extensions"
- select CPUMASK_OFFSTACK
- depends on ARC_PLAT_EZNPS && SMP
- default y
- help
- Here we add new hierarchy for CPUs topology.
- We got:
- Core
- Thread
- At the new thread level each CPU represent one HW thread.
- At highest hierarchy each core contain 16 threads,
- any of them seem like CPU from Linux point of view.
- All threads within same core share the execution unit of the
- core and HW scheduler round robin between them.
-
-config EZNPS_MEM_ERROR_ALIGN
- bool "ARC-EZchip Memory error as an exception"
- depends on EZNPS_MTM_EXT
- default n
- help
- On the real chip of the NPS, user memory errors are handled
- as a machine check exception, which is fatal, whereas on
- simulator platform for NPS, is handled as a Level 2 interrupt
- (just a stock ARC700) which is recoverable. This option makes
- simulator behave like hardware.
-
-config EZNPS_SHARED_AUX_REGS
- bool "ARC-EZchip Shared Auxiliary Registers Per Core"
- depends on ARC_PLAT_EZNPS
- default y
- help
- On the real chip of the NPS, auxiliary registers are shared between
- all the cpus of the core, whereas on simulator platform for NPS,
- each cpu has a different set of auxiliary registers. Configuration
- should be unset if auxiliary registers are not shared between the cpus
- of the core, so there will be a need to initialize them per cpu.
deleted file mode 100644
@@ -1,8 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-#
-# Makefile for the linux kernel.
-#
-
-obj-y := entry.o platform.o ctop.o
-obj-$(CONFIG_SMP) += smp.o
-obj-$(CONFIG_EZNPS_MTM_EXT) += mtm.o
deleted file mode 100644
@@ -1,21 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright(c) 2015 EZchip Technologies.
- */
-
-#include <linux/sched.h>
-#include <asm/processor.h>
-#include <plat/ctop.h>
-
-void dp_save_restore(struct task_struct *prev, struct task_struct *next)
-{
- struct eznps_dp *prev_task_dp = &prev->thread.dp;
- struct eznps_dp *next_task_dp = &next->thread.dp;
-
- /* Here we save all Data Plane related auxiliary registers */
- prev_task_dp->eflags = read_aux_reg(CTOP_AUX_EFLAGS);
- write_aux_reg(CTOP_AUX_EFLAGS, next_task_dp->eflags);
-
- prev_task_dp->gpa1 = read_aux_reg(CTOP_AUX_GPA1);
- write_aux_reg(CTOP_AUX_GPA1, next_task_dp->gpa1);
-}
deleted file mode 100644
@@ -1,60 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*******************************************************************************
-
- EZNPS CPU startup Code
- Copyright(c) 2012 EZchip Technologies.
-
-
-*******************************************************************************/
-#include <linux/linkage.h>
-#include <asm/entry.h>
-#include <asm/cache.h>
-#include <plat/ctop.h>
-
- .cpu A7
-
- .section .init.text, "ax",@progbits
- .align 1024 ; HW requierment for restart first PC
-
-ENTRY(res_service)
-#if defined(CONFIG_EZNPS_MTM_EXT) && defined(CONFIG_EZNPS_SHARED_AUX_REGS)
- ; There is no work for HW thread id != 0
- lr r3, [CTOP_AUX_THREAD_ID]
- cmp r3, 0
- jne stext
-#endif
-
-#ifdef CONFIG_ARC_HAS_DCACHE
- ; With no cache coherency mechanism D$ need to be used very carefully.
- ; Address space:
- ; 0G-2G: We disable CONFIG_ARC_CACHE_PAGES.
- ; 2G-3G: We disable D$ by setting this bit.
- ; 3G-4G: D$ is disabled by architecture.
- ; FMT are huge pages for user application reside at 0-2G.
- ; Only FMT left as one who can use D$ where each such page got
- ; disable/enable bit for cachability.
- ; Programmer will use FMT pages for private data so cache coherency
- ; would not be a problem.
- ; First thing we invalidate D$
- sr 1, [ARC_REG_DC_IVDC]
- sr HW_COMPLY_KRN_NOT_D_CACHED, [CTOP_AUX_HW_COMPLY]
-#endif
-
-#ifdef CONFIG_SMP
- ; We set logical cpuid to be used by GET_CPUID
- ; We do not use physical cpuid since we want ids to be continious when
- ; it comes to cpus on the same quad cluster.
- ; This is useful for applications that used shared resources of a quad
- ; cluster such SRAMS.
- lr r3, [CTOP_AUX_CORE_ID]
- sr r3, [CTOP_AUX_LOGIC_CORE_ID]
- lr r3, [CTOP_AUX_CLUSTER_ID]
- ; Set logical is acheived by swap of 2 middle bits of cluster id (4 bit)
- ; r3 is used since we use short instruction and we need q-class reg
- .short CTOP_INST_MOV2B_FLIP_R3_B1_B2_INST
- .word CTOP_INST_MOV2B_FLIP_R3_B1_B2_LIMM
- sr r3, [CTOP_AUX_LOGIC_CLUSTER_ID]
-#endif
-
- j stext
-END(res_service)
deleted file mode 100644
@@ -1,208 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright(c) 2015 EZchip Technologies.
- */
-
-#ifndef _PLAT_EZNPS_CTOP_H
-#define _PLAT_EZNPS_CTOP_H
-
-#ifndef CONFIG_ARC_PLAT_EZNPS
-#error "Incorrect ctop.h include"
-#endif
-
-#include <linux/bits.h>
-#include <linux/types.h>
-#include <soc/nps/common.h>
-
-/* core auxiliary registers */
-#ifdef __ASSEMBLY__
-#define CTOP_AUX_BASE (-0x800)
-#else
-#define CTOP_AUX_BASE 0xFFFFF800
-#endif
-
-#define CTOP_AUX_GLOBAL_ID (CTOP_AUX_BASE + 0x000)
-#define CTOP_AUX_CLUSTER_ID (CTOP_AUX_BASE + 0x004)
-#define CTOP_AUX_CORE_ID (CTOP_AUX_BASE + 0x008)
-#define CTOP_AUX_THREAD_ID (CTOP_AUX_BASE + 0x00C)
-#define CTOP_AUX_LOGIC_GLOBAL_ID (CTOP_AUX_BASE + 0x010)
-#define CTOP_AUX_LOGIC_CLUSTER_ID (CTOP_AUX_BASE + 0x014)
-#define CTOP_AUX_LOGIC_CORE_ID (CTOP_AUX_BASE + 0x018)
-#define CTOP_AUX_MT_CTRL (CTOP_AUX_BASE + 0x020)
-#define CTOP_AUX_HW_COMPLY (CTOP_AUX_BASE + 0x024)
-#define CTOP_AUX_DPC (CTOP_AUX_BASE + 0x02C)
-#define CTOP_AUX_LPC (CTOP_AUX_BASE + 0x030)
-#define CTOP_AUX_EFLAGS (CTOP_AUX_BASE + 0x080)
-#define CTOP_AUX_GPA1 (CTOP_AUX_BASE + 0x08C)
-#define CTOP_AUX_UDMC (CTOP_AUX_BASE + 0x300)
-
-/* EZchip core instructions */
-#define CTOP_INST_HWSCHD_WFT_IE12 0x3E6F7344
-#define CTOP_INST_HWSCHD_OFF_R4 0x3C6F00BF
-#define CTOP_INST_HWSCHD_RESTORE_R4 0x3E6F7103
-#define CTOP_INST_SCHD_RW 0x3E6F7004
-#define CTOP_INST_SCHD_RD 0x3E6F7084
-#define CTOP_INST_ASRI_0_R3 0x3B56003E
-#define CTOP_INST_XEX_DI_R2_R2_R3 0x4A664C00
-#define CTOP_INST_EXC_DI_R2_R2_R3 0x4A664C01
-#define CTOP_INST_AADD_DI_R2_R2_R3 0x4A664C02
-#define CTOP_INST_AAND_DI_R2_R2_R3 0x4A664C04
-#define CTOP_INST_AOR_DI_R2_R2_R3 0x4A664C05
-#define CTOP_INST_AXOR_DI_R2_R2_R3 0x4A664C06
-
-/* Do not use D$ for address in 2G-3G */
-#define HW_COMPLY_KRN_NOT_D_CACHED BIT(28)
-
-#define NPS_MSU_EN_CFG 0x80
-#define NPS_CRG_BLKID 0x480
-#define NPS_CRG_SYNC_BIT BIT(0)
-#define NPS_GIM_BLKID 0x5C0
-
-/* GIM registers and fields*/
-#define NPS_GIM_UART_LINE BIT(7)
-#define NPS_GIM_DBG_LAN_EAST_TX_DONE_LINE BIT(10)
-#define NPS_GIM_DBG_LAN_EAST_RX_RDY_LINE BIT(11)
-#define NPS_GIM_DBG_LAN_WEST_TX_DONE_LINE BIT(25)
-#define NPS_GIM_DBG_LAN_WEST_RX_RDY_LINE BIT(26)
-
-#ifndef __ASSEMBLY__
-/* Functional registers definition */
-struct nps_host_reg_mtm_cfg {
- union {
- struct {
- u32 gen:1, gdis:1, clk_gate_dis:1, asb:1,
- __reserved:9, nat:3, ten:16;
- };
- u32 value;
- };
-};
-
-struct nps_host_reg_mtm_cpu_cfg {
- union {
- struct {
- u32 csa:22, dmsid:6, __reserved:3, cs:1;
- };
- u32 value;
- };
-};
-
-struct nps_host_reg_thr_init {
- union {
- struct {
- u32 str:1, __reserved:27, thr_id:4;
- };
- u32 value;
- };
-};
-
-struct nps_host_reg_thr_init_sts {
- union {
- struct {
- u32 bsy:1, err:1, __reserved:26, thr_id:4;
- };
- u32 value;
- };
-};
-
-struct nps_host_reg_msu_en_cfg {
- union {
- struct {
- u32 __reserved1:11,
- rtc_en:1, ipc_en:1, gim_1_en:1,
- gim_0_en:1, ipi_en:1, buff_e_rls_bmuw:1,
- buff_e_alc_bmuw:1, buff_i_rls_bmuw:1, buff_i_alc_bmuw:1,
- buff_e_rls_bmue:1, buff_e_alc_bmue:1, buff_i_rls_bmue:1,
- buff_i_alc_bmue:1, __reserved2:1, buff_e_pre_en:1,
- buff_i_pre_en:1, pmuw_ja_en:1, pmue_ja_en:1,
- pmuw_nj_en:1, pmue_nj_en:1, msu_en:1;
- };
- u32 value;
- };
-};
-
-struct nps_host_reg_gim_p_int_dst {
- union {
- struct {
- u32 int_out_en:1, __reserved1:4,
- is:1, intm:2, __reserved2:4,
- nid:4, __reserved3:4, cid:4,
- __reserved4:4, tid:4;
- };
- u32 value;
- };
-};
-
-/* AUX registers definition */
-struct nps_host_reg_aux_dpc {
- union {
- struct {
- u32 ien:1, men:1, hen:1, reserved:29;
- };
- u32 value;
- };
-};
-
-struct nps_host_reg_aux_udmc {
- union {
- struct {
- u32 dcp:1, cme:1, __reserved:19, nat:3,
- __reserved2:5, dcas:3;
- };
- u32 value;
- };
-};
-
-struct nps_host_reg_aux_mt_ctrl {
- union {
- struct {
- u32 mten:1, hsen:1, scd:1, sten:1,
- st_cnt:8, __reserved:8,
- hs_cnt:8, __reserved1:4;
- };
- u32 value;
- };
-};
-
-struct nps_host_reg_aux_hw_comply {
- union {
- struct {
- u32 me:1, le:1, te:1, knc:1, __reserved:28;
- };
- u32 value;
- };
-};
-
-struct nps_host_reg_aux_lpc {
- union {
- struct {
- u32 mep:1, __reserved:31;
- };
- u32 value;
- };
-};
-
-/* CRG registers */
-#define REG_GEN_PURP_0 nps_host_reg_non_cl(NPS_CRG_BLKID, 0x1BF)
-
-/* GIM registers */
-#define REG_GIM_P_INT_EN_0 nps_host_reg_non_cl(NPS_GIM_BLKID, 0x100)
-#define REG_GIM_P_INT_POL_0 nps_host_reg_non_cl(NPS_GIM_BLKID, 0x110)
-#define REG_GIM_P_INT_SENS_0 nps_host_reg_non_cl(NPS_GIM_BLKID, 0x114)
-#define REG_GIM_P_INT_BLK_0 nps_host_reg_non_cl(NPS_GIM_BLKID, 0x118)
-#define REG_GIM_P_INT_DST_10 nps_host_reg_non_cl(NPS_GIM_BLKID, 0x13A)
-#define REG_GIM_P_INT_DST_11 nps_host_reg_non_cl(NPS_GIM_BLKID, 0x13B)
-#define REG_GIM_P_INT_DST_25 nps_host_reg_non_cl(NPS_GIM_BLKID, 0x149)
-#define REG_GIM_P_INT_DST_26 nps_host_reg_non_cl(NPS_GIM_BLKID, 0x14A)
-
-#else
-
-.macro GET_CPU_ID reg
- lr \reg, [CTOP_AUX_LOGIC_GLOBAL_ID]
-#ifndef CONFIG_EZNPS_MTM_EXT
- lsr \reg, \reg, 4
-#endif
-.endm
-
-#endif /* __ASSEMBLY__ */
-
-#endif /* _PLAT_EZNPS_CTOP_H */
deleted file mode 100644
@@ -1,49 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright(c) 2015 EZchip Technologies.
- */
-
-#ifndef _PLAT_EZNPS_MTM_H
-#define _PLAT_EZNPS_MTM_H
-
-#include <plat/ctop.h>
-
-static inline void *nps_mtm_reg_addr(u32 cpu, u32 reg)
-{
- struct global_id gid;
- u32 core, blkid;
-
- gid.value = cpu;
- core = gid.core;
- blkid = (((core & 0x0C) << 2) | (core & 0x03));
-
- return nps_host_reg(cpu, blkid, reg);
-}
-
-#ifdef CONFIG_EZNPS_MTM_EXT
-#define NPS_CPU_TO_THREAD_NUM(cpu) \
- ({ struct global_id gid; gid.value = cpu; gid.thread; })
-
-/* MTM registers */
-#define MTM_CFG(cpu) nps_mtm_reg_addr(cpu, 0x81)
-#define MTM_THR_INIT(cpu) nps_mtm_reg_addr(cpu, 0x92)
-#define MTM_THR_INIT_STS(cpu) nps_mtm_reg_addr(cpu, 0x93)
-
-#define get_thread(map) map.thread
-#define eznps_max_cpus 4096
-#define eznps_cpus_per_cluster 256
-
-void mtm_enable_core(unsigned int cpu);
-int mtm_enable_thread(int cpu);
-#else /* !CONFIG_EZNPS_MTM_EXT */
-
-#define get_thread(map) 0
-#define eznps_max_cpus 256
-#define eznps_cpus_per_cluster 16
-#define mtm_enable_core(cpu)
-#define mtm_enable_thread(cpu) 1
-#define NPS_CPU_TO_THREAD_NUM(cpu) 0
-
-#endif /* CONFIG_EZNPS_MTM_EXT */
-
-#endif /* _PLAT_EZNPS_MTM_H */
deleted file mode 100644
@@ -1,15 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright(c) 2015 EZchip Technologies.
- */
-
-#ifndef __PLAT_EZNPS_SMP_H
-#define __PLAT_EZNPS_SMP_H
-
-#ifdef CONFIG_SMP
-
-extern void res_service(void);
-
-#endif /* CONFIG_SMP */
-
-#endif
deleted file mode 100644
@@ -1,166 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright(c) 2015 EZchip Technologies.
- */
-
-#include <linux/smp.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/io.h>
-#include <linux/log2.h>
-#include <asm/arcregs.h>
-#include <plat/mtm.h>
-#include <plat/smp.h>
-
-#define MT_HS_CNT_MIN 0x01
-#define MT_HS_CNT_MAX 0xFF
-#define MT_CTRL_ST_CNT 0xF
-#define NPS_NUM_HW_THREADS 0x10
-
-static int mtm_hs_ctr = MT_HS_CNT_MAX;
-
-#ifdef CONFIG_EZNPS_MEM_ERROR_ALIGN
-int do_memory_error(unsigned long address, struct pt_regs *regs)
-{
- die("Invalid Mem Access", regs, address);
-
- return 1;
-}
-#endif
-
-static void mtm_init_nat(int cpu)
-{
- struct nps_host_reg_mtm_cfg mtm_cfg;
- struct nps_host_reg_aux_udmc udmc;
- int log_nat, nat = 0, i, t;
-
- /* Iterate core threads and update nat */
- for (i = 0, t = cpu; i < NPS_NUM_HW_THREADS; i++, t++)
- nat += test_bit(t, cpumask_bits(cpu_possible_mask));
-
- log_nat = ilog2(nat);
-
- udmc.value = read_aux_reg(CTOP_AUX_UDMC);
- udmc.nat = log_nat;
- write_aux_reg(CTOP_AUX_UDMC, udmc.value);
-
- mtm_cfg.value = ioread32be(MTM_CFG(cpu));
- mtm_cfg.nat = log_nat;
- iowrite32be(mtm_cfg.value, MTM_CFG(cpu));
-}
-
-static void mtm_init_thread(int cpu)
-{
- int i, tries = 5;
- struct nps_host_reg_thr_init thr_init;
- struct nps_host_reg_thr_init_sts thr_init_sts;
-
- /* Set thread init register */
- thr_init.value = 0;
- iowrite32be(thr_init.value, MTM_THR_INIT(cpu));
- thr_init.thr_id = NPS_CPU_TO_THREAD_NUM(cpu);
- thr_init.str = 1;
- iowrite32be(thr_init.value, MTM_THR_INIT(cpu));
-
- /* Poll till thread init is done */
- for (i = 0; i < tries; i++) {
- thr_init_sts.value = ioread32be(MTM_THR_INIT_STS(cpu));
- if (thr_init_sts.thr_id == thr_init.thr_id) {
- if (thr_init_sts.bsy)
- continue;
- else if (thr_init_sts.err)
- pr_warn("Failed to thread init cpu %u\n", cpu);
- break;
- }
-
- pr_warn("Wrong thread id in thread init for cpu %u\n", cpu);
- break;
- }
-
- if (i == tries)
- pr_warn("Got thread init timeout for cpu %u\n", cpu);
-}
-
-int mtm_enable_thread(int cpu)
-{
- struct nps_host_reg_mtm_cfg mtm_cfg;
-
- if (NPS_CPU_TO_THREAD_NUM(cpu) == 0)
- return 1;
-
- /* Enable thread in mtm */
- mtm_cfg.value = ioread32be(MTM_CFG(cpu));
- mtm_cfg.ten |= (1 << (NPS_CPU_TO_THREAD_NUM(cpu)));
- iowrite32be(mtm_cfg.value, MTM_CFG(cpu));
-
- return 0;
-}
-
-void mtm_enable_core(unsigned int cpu)
-{
- int i;
- struct nps_host_reg_aux_mt_ctrl mt_ctrl;
- struct nps_host_reg_mtm_cfg mtm_cfg;
- struct nps_host_reg_aux_dpc dpc;
-
- /*
- * Initializing dpc register in each CPU.
- * Overwriting the init value of the DPC
- * register so that CMEM and FMT virtual address
- * spaces are accessible, and Data Plane HW
- * facilities are enabled.
- */
- dpc.ien = 1;
- dpc.men = 1;
- write_aux_reg(CTOP_AUX_DPC, dpc.value);
-
- if (NPS_CPU_TO_THREAD_NUM(cpu) != 0)
- return;
-
- /* Initialize Number of Active Threads */
- mtm_init_nat(cpu);
-
- /* Initialize mtm_cfg */
- mtm_cfg.value = ioread32be(MTM_CFG(cpu));
- mtm_cfg.ten = 1;
- iowrite32be(mtm_cfg.value, MTM_CFG(cpu));
-
- /* Initialize all other threads in core */
- for (i = 1; i < NPS_NUM_HW_THREADS; i++)
- mtm_init_thread(cpu + i);
-
-
- /* Enable HW schedule, stall counter, mtm */
- mt_ctrl.value = 0;
- mt_ctrl.hsen = 1;
- mt_ctrl.hs_cnt = mtm_hs_ctr;
- mt_ctrl.mten = 1;
- write_aux_reg(CTOP_AUX_MT_CTRL, mt_ctrl.value);
-
- /*
- * HW scheduling mechanism will start working
- * Only after call to instruction "schd.rw".
- * cpu_relax() calls "schd.rw" instruction.
- */
- cpu_relax();
-}
-
-/* Verify and set the value of the mtm hs counter */
-static int __init set_mtm_hs_ctr(char *ctr_str)
-{
- int hs_ctr;
- int ret;
-
- ret = kstrtoint(ctr_str, 0, &hs_ctr);
-
- if (ret || hs_ctr > MT_HS_CNT_MAX || hs_ctr < MT_HS_CNT_MIN) {
- pr_err("** Invalid @nps_mtm_hs_ctr [%d] needs to be [%d:%d] (incl)\n",
- hs_ctr, MT_HS_CNT_MIN, MT_HS_CNT_MAX);
- return -EINVAL;
- }
-
- mtm_hs_ctr = hs_ctr;
-
- return 0;
-}
-early_param("nps_mtm_hs_ctr", set_mtm_hs_ctr);
deleted file mode 100644
@@ -1,91 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright(c) 2015 EZchip Technologies.
- */
-
-#include <linux/init.h>
-#include <linux/io.h>
-#include <asm/mach_desc.h>
-#include <plat/mtm.h>
-
-static void __init eznps_configure_msu(void)
-{
- int cpu;
- struct nps_host_reg_msu_en_cfg msu_en_cfg = {.value = 0};
-
- msu_en_cfg.msu_en = 1;
- msu_en_cfg.ipi_en = 1;
- msu_en_cfg.gim_0_en = 1;
- msu_en_cfg.gim_1_en = 1;
-
- /* enable IPI and GIM messages on all clusters */
- for (cpu = 0 ; cpu < eznps_max_cpus; cpu += eznps_cpus_per_cluster)
- iowrite32be(msu_en_cfg.value,
- nps_host_reg(cpu, NPS_MSU_BLKID, NPS_MSU_EN_CFG));
-}
-
-static void __init eznps_configure_gim(void)
-{
- u32 reg_value;
- u32 gim_int_lines;
- struct nps_host_reg_gim_p_int_dst gim_p_int_dst = {.value = 0};
-
- gim_int_lines = NPS_GIM_UART_LINE;
- gim_int_lines |= NPS_GIM_DBG_LAN_EAST_TX_DONE_LINE;
- gim_int_lines |= NPS_GIM_DBG_LAN_EAST_RX_RDY_LINE;
- gim_int_lines |= NPS_GIM_DBG_LAN_WEST_TX_DONE_LINE;
- gim_int_lines |= NPS_GIM_DBG_LAN_WEST_RX_RDY_LINE;
-
- /*
- * IRQ polarity
- * low or high level
- * negative or positive edge
- */
- reg_value = ioread32be(REG_GIM_P_INT_POL_0);
- reg_value &= ~gim_int_lines;
- iowrite32be(reg_value, REG_GIM_P_INT_POL_0);
-
- /* IRQ type level or edge */
- reg_value = ioread32be(REG_GIM_P_INT_SENS_0);
- reg_value |= NPS_GIM_DBG_LAN_EAST_TX_DONE_LINE;
- reg_value |= NPS_GIM_DBG_LAN_WEST_TX_DONE_LINE;
- iowrite32be(reg_value, REG_GIM_P_INT_SENS_0);
-
- /*
- * GIM interrupt select type for
- * dbg_lan TX and RX interrupts
- * should be type 1
- * type 0 = IRQ line 6
- * type 1 = IRQ line 7
- */
- gim_p_int_dst.is = 1;
- iowrite32be(gim_p_int_dst.value, REG_GIM_P_INT_DST_10);
- iowrite32be(gim_p_int_dst.value, REG_GIM_P_INT_DST_11);
- iowrite32be(gim_p_int_dst.value, REG_GIM_P_INT_DST_25);
- iowrite32be(gim_p_int_dst.value, REG_GIM_P_INT_DST_26);
-
- /*
- * CTOP IRQ lines should be defined
- * as blocking in GIM
- */
- iowrite32be(gim_int_lines, REG_GIM_P_INT_BLK_0);
-
- /* enable CTOP IRQ lines in GIM */
- iowrite32be(gim_int_lines, REG_GIM_P_INT_EN_0);
-}
-
-static void __init eznps_early_init(void)
-{
- eznps_configure_msu();
- eznps_configure_gim();
-}
-
-static const char *eznps_compat[] __initconst = {
- "ezchip,arc-nps",
- NULL,
-};
-
-MACHINE_START(NPS, "nps")
- .dt_compat = eznps_compat,
- .init_early = eznps_early_init,
-MACHINE_END
deleted file mode 100644
@@ -1,138 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright(c) 2015 EZchip Technologies.
- */
-
-#include <linux/smp.h>
-#include <linux/of_fdt.h>
-#include <linux/io.h>
-#include <linux/irqdomain.h>
-#include <asm/irq.h>
-#include <plat/ctop.h>
-#include <plat/smp.h>
-#include <plat/mtm.h>
-
-#define NPS_DEFAULT_MSID 0x34
-#define NPS_MTM_CPU_CFG 0x90
-
-static char smp_cpuinfo_buf[128] = {"Extn [EZNPS-SMP]\t: On\n"};
-
-/* Get cpu map from device tree */
-static int __init eznps_get_map(const char *name, struct cpumask *cpumask)
-{
- unsigned long dt_root = of_get_flat_dt_root();
- const char *buf;
-
- buf = of_get_flat_dt_prop(dt_root, name, NULL);
- if (!buf)
- return 1;
-
- cpulist_parse(buf, cpumask);
-
- return 0;
-}
-
-/* Update board cpu maps */
-static void __init eznps_init_cpumasks(void)
-{
- struct cpumask cpumask;
-
- if (eznps_get_map("present-cpus", &cpumask)) {
- pr_err("Failed to get present-cpus from dtb");
- return;
- }
- init_cpu_present(&cpumask);
-
- if (eznps_get_map("possible-cpus", &cpumask)) {
- pr_err("Failed to get possible-cpus from dtb");
- return;
- }
- init_cpu_possible(&cpumask);
-}
-
-static void eznps_init_core(unsigned int cpu)
-{
- u32 sync_value;
- struct nps_host_reg_aux_hw_comply hw_comply;
- struct nps_host_reg_aux_lpc lpc;
-
- if (NPS_CPU_TO_THREAD_NUM(cpu) != 0)
- return;
-
- hw_comply.value = read_aux_reg(CTOP_AUX_HW_COMPLY);
- hw_comply.me = 1;
- hw_comply.le = 1;
- hw_comply.te = 1;
- write_aux_reg(CTOP_AUX_HW_COMPLY, hw_comply.value);
-
- /* Enable MMU clock */
- lpc.mep = 1;
- write_aux_reg(CTOP_AUX_LPC, lpc.value);
-
- /* Boot CPU only */
- if (!cpu) {
- /* Write to general purpose register in CRG */
- sync_value = ioread32be(REG_GEN_PURP_0);
- sync_value |= NPS_CRG_SYNC_BIT;
- iowrite32be(sync_value, REG_GEN_PURP_0);
- }
-}
-
-/*
- * Master kick starting another CPU
- */
-static void __init eznps_smp_wakeup_cpu(int cpu, unsigned long pc)
-{
- struct nps_host_reg_mtm_cpu_cfg cpu_cfg;
-
- if (mtm_enable_thread(cpu) == 0)
- return;
-
- /* set PC, dmsid, and start CPU */
- cpu_cfg.value = (u32)res_service;
- cpu_cfg.dmsid = NPS_DEFAULT_MSID;
- cpu_cfg.cs = 1;
- iowrite32be(cpu_cfg.value, nps_mtm_reg_addr(cpu, NPS_MTM_CPU_CFG));
-}
-
-static void eznps_ipi_send(int cpu)
-{
- struct global_id gid;
- struct {
- union {
- struct {
- u32 num:8, cluster:8, core:8, thread:8;
- };
- u32 value;
- };
- } ipi;
-
- gid.value = cpu;
- ipi.thread = get_thread(gid);
- ipi.core = gid.core;
- ipi.cluster = nps_cluster_logic_to_phys(gid.cluster);
- ipi.num = NPS_IPI_IRQ;
-
- __asm__ __volatile__(
- " mov r3, %0\n"
- " .word %1\n"
- :
- : "r"(ipi.value), "i"(CTOP_INST_ASRI_0_R3)
- : "r3");
-}
-
-static void eznps_init_per_cpu(int cpu)
-{
- smp_ipi_irq_setup(cpu, NPS_IPI_IRQ);
-
- eznps_init_core(cpu);
- mtm_enable_core(cpu);
-}
-
-struct plat_smp_ops plat_smp_ops = {
- .info = smp_cpuinfo_buf,
- .init_early_smp = eznps_init_cpumasks,
- .cpu_kick = eznps_smp_wakeup_cpu,
- .ipi_send = eznps_ipi_send,
- .init_per_cpu = eznps_init_per_cpu,
-};
NPS customers are no longer doing active development, as evident from rand config build failures reported in recent times, so drop support for NPS platform. Signed-off-by: Vineet Gupta <vgupta@synopsys.com> --- MAINTAINERS | 7 - arch/arc/Makefile | 5 - arch/arc/configs/nps_defconfig | 80 --------- arch/arc/include/asm/atomic.h | 104 ------------ arch/arc/include/asm/barrier.h | 9 +- arch/arc/include/asm/bitops.h | 58 +------ arch/arc/include/asm/cmpxchg.h | 70 +------- arch/arc/include/asm/entry-compact.h | 27 --- arch/arc/include/asm/processor.h | 37 ----- arch/arc/include/asm/ptrace.h | 5 - arch/arc/include/asm/setup.h | 4 - arch/arc/include/asm/spinlock.h | 6 - arch/arc/include/asm/switch_to.h | 9 - arch/arc/kernel/ctx_sw.c | 13 -- arch/arc/kernel/process.c | 15 -- arch/arc/mm/tlbex.S | 7 - arch/arc/plat-eznps/Kconfig | 58 ------- arch/arc/plat-eznps/Makefile | 8 - arch/arc/plat-eznps/ctop.c | 21 --- arch/arc/plat-eznps/entry.S | 60 ------- arch/arc/plat-eznps/include/plat/ctop.h | 208 ------------------------ arch/arc/plat-eznps/include/plat/mtm.h | 49 ------ arch/arc/plat-eznps/include/plat/smp.h | 15 -- arch/arc/plat-eznps/mtm.c | 166 ------------------- arch/arc/plat-eznps/platform.c | 91 ----------- arch/arc/plat-eznps/smp.c | 138 ---------------- 26 files changed, 5 insertions(+), 1265 deletions(-) delete mode 100644 arch/arc/configs/nps_defconfig delete mode 100644 arch/arc/plat-eznps/Kconfig delete mode 100644 arch/arc/plat-eznps/Makefile delete mode 100644 arch/arc/plat-eznps/ctop.c delete mode 100644 arch/arc/plat-eznps/entry.S delete mode 100644 arch/arc/plat-eznps/include/plat/ctop.h delete mode 100644 arch/arc/plat-eznps/include/plat/mtm.h delete mode 100644 arch/arc/plat-eznps/include/plat/smp.h delete mode 100644 arch/arc/plat-eznps/mtm.c delete mode 100644 arch/arc/plat-eznps/platform.c delete mode 100644 arch/arc/plat-eznps/smp.c