diff --git a/target/linux/ath25/Makefile b/target/linux/ath25/Makefile
index ae867e9..03aa2a9 100644
--- a/target/linux/ath25/Makefile
+++ b/target/linux/ath25/Makefile
@@ -12,7 +12,7 @@ BOARDNAME:=Atheros AR231x/AR5312
 FEATURES:=squashfs low_mem
 MAINTAINER:=Sergey Ryazanov <ryazanov.s.a@gmail.com>
 
-KERNEL_PATCHVER:=3.18
+KERNEL_PATCHVER:=4.4
 
 include $(INCLUDE_DIR)/target.mk
 
diff --git a/target/linux/ath25/config-3.18 b/target/linux/ath25/config-3.18
deleted file mode 100644
index 8856041..0000000
--- a/target/linux/ath25/config-3.18
+++ /dev/null
@@ -1,136 +0,0 @@
-CONFIG_ADM6996_PHY=y
-CONFIG_AR2315_WDT=y
-CONFIG_AR8216_PHY=y
-CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
-CONFIG_ARCH_DISCARD_MEMBLOCK=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-# CONFIG_ARCH_HAS_SG_CHAIN is not set
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ATH25=y
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CEVT_R4K=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMDLINE="console=ttyS0,9600 rootfstype=squashfs,jffs2"
-CONFIG_CMDLINE_BOOL=y
-# CONFIG_CMDLINE_OVERRIDE is not set
-CONFIG_CPU_BIG_ENDIAN=y
-CONFIG_CPU_GENERIC_DUMP_TLB=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_CPU_HAS_SYNC=y
-CONFIG_CPU_MIPS32=y
-CONFIG_CPU_MIPS32_R1=y
-CONFIG_CPU_MIPSR1=y
-CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y
-CONFIG_CPU_R4K_CACHE_TLB=y
-CONFIG_CPU_R4K_FPU=y
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-CONFIG_CSRC_R4K=y
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_EARLY_PRINTK=y
-CONFIG_ETHERNET_PACKET_MANGLE=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_GENERIC_CMOS_UPDATE=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_AR2315=y
-CONFIG_GPIO_AR5312=y
-CONFIG_GPIO_DEVRES=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_HARDWARE_WATCHPOINTS=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_BPF_JIT=y
-CONFIG_HAVE_CC_STACKPROTECTOR=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
-CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HW_HAS_PCI=y
-CONFIG_HW_RANDOM=y
-CONFIG_HZ_PERIODIC=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IP17XX_PHY=y
-CONFIG_IRQ_CPU=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_LEDS_GPIO=y
-CONFIG_MDIO_BOARDINFO=y
-CONFIG_MIPS=y
-# CONFIG_MIPS_HUGE_TLB_SUPPORT is not set
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-# CONFIG_MIPS_MACHINE is not set
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MTD_AR2315=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-# CONFIG_MTD_CFI_GEOMETRY is not set
-# CONFIG_MTD_CFI_INTELEXT is not set
-CONFIG_MTD_MYLOADER_PARTS=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-3
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MVSWITCH_PHY=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NET_AR231X=y
-CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y
-# CONFIG_NO_IOPORT_MAP is not set
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_PCI=y
-CONFIG_PCI_AR2315=y
-CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PHYLIB=y
-# CONFIG_PREEMPT_RCU is not set
-# CONFIG_RCU_STALL_COMMON is not set
-# CONFIG_SCSI_DMA is not set
-CONFIG_SERIAL_8250_NR_UARTS=1
-CONFIG_SERIAL_8250_RUNTIME_UARTS=1
-CONFIG_SOC_AR2315=y
-CONFIG_SOC_AR5312=y
-# CONFIG_SWAP is not set
-CONFIG_SWCONFIG=y
-CONFIG_SYS_HAS_CPU_MIPS32_R1=y
-CONFIG_SYS_HAS_EARLY_PRINTK=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_USB_SUPPORT=y
-CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/ath25/config-4.4 b/target/linux/ath25/config-4.4
new file mode 100644
index 0000000..f85d6fd
--- /dev/null
+++ b/target/linux/ath25/config-4.4
@@ -0,0 +1,137 @@
+CONFIG_ADM6996_PHY=y
+CONFIG_AR2315_WDT=y
+CONFIG_AR8216_PHY=y
+CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
+CONFIG_ARCH_DISCARD_MEMBLOCK=y
+CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
+# CONFIG_ARCH_HAS_SG_CHAIN is not set
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_ATH25=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_CEVT_R4K=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_CMDLINE="console=ttyS0,9600 rootfstype=squashfs,jffs2"
+CONFIG_CMDLINE_BOOL=y
+# CONFIG_CMDLINE_OVERRIDE is not set
+CONFIG_CPU_BIG_ENDIAN=y
+CONFIG_CPU_GENERIC_DUMP_TLB=y
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_CPU_HAS_SYNC=y
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPS32_R1=y
+CONFIG_CPU_MIPSR1=y
+CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y
+CONFIG_CPU_R4K_CACHE_TLB=y
+CONFIG_CPU_R4K_FPU=y
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+CONFIG_CSRC_R4K=y
+CONFIG_DMA_NONCOHERENT=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_ETHERNET_PACKET_MANGLE=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_AR2315=y
+CONFIG_GPIO_AR5312=y
+CONFIG_GPIO_DEVRES=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_HARDWARE_WATCHPOINTS=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
+CONFIG_HAVE_BPF_JIT=y
+CONFIG_HAVE_CC_STACKPROTECTOR=y
+CONFIG_HAVE_CONTEXT_TRACKING=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DMA_ATTRS=y
+CONFIG_HAVE_DMA_CONTIGUOUS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HW_HAS_PCI=y
+CONFIG_HW_RANDOM=y
+CONFIG_HZ_PERIODIC=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_IP17XX_PHY=y
+CONFIG_IRQ_CPU=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_LEDS_GPIO=y
+CONFIG_MDIO_BOARDINFO=y
+CONFIG_MIPS=y
+# CONFIG_MIPS_HUGE_TLB_SUPPORT is not set
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+# CONFIG_MIPS_MACHINE is not set
+CONFIG_MODULES_USE_ELF_REL=y
+CONFIG_MTD_AR2315=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+# CONFIG_MTD_CFI_GEOMETRY is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_MYLOADER_PARTS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-3
+CONFIG_MTD_REDBOOT_PARTS=y
+CONFIG_MVSWITCH_PHY=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_NET_AR231X=y
+CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y
+# CONFIG_NO_IOPORT_MAP is not set
+# CONFIG_OF is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_PCI=y
+CONFIG_PCI_AR2315=y
+CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PHYLIB=y
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_RCU_STALL_COMMON is not set
+# CONFIG_SCSI_DMA is not set
+CONFIG_SERIAL_8250_NR_UARTS=1
+CONFIG_SERIAL_8250_RUNTIME_UARTS=1
+CONFIG_SOC_AR2315=y
+CONFIG_SOC_AR5312=y
+# CONFIG_SWAP is not set
+CONFIG_SWCONFIG=y
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_USB_SUPPORT=y
+CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/ath25/patches-3.18/010-board.patch b/target/linux/ath25/patches-3.18/010-board.patch
deleted file mode 100644
index 03332b6..0000000
--- a/target/linux/ath25/patches-3.18/010-board.patch
+++ /dev/null
@@ -1,2189 +0,0 @@
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -96,6 +96,19 @@ config AR7
- 	  Support for the Texas Instruments AR7 System-on-a-Chip
- 	  family: TNETD7100, 7200 and 7300.
- 
-+config ATH25
-+	bool "Atheros AR231x/AR531x SoC support"
-+	select CEVT_R4K
-+	select CSRC_R4K
-+	select DMA_NONCOHERENT
-+	select IRQ_CPU
-+	select IRQ_DOMAIN
-+	select SYS_HAS_CPU_MIPS32_R1
-+	select SYS_SUPPORTS_BIG_ENDIAN
-+	select SYS_SUPPORTS_32BIT_KERNEL
-+	help
-+	  Support for Atheros AR231x and Atheros AR531x based boards
-+
- config ATH79
- 	bool "Atheros AR71XX/AR724X/AR913X based boards"
- 	select ARCH_REQUIRE_GPIOLIB
-@@ -835,6 +848,7 @@ config MIPS_PARAVIRT
- endchoice
- 
- source "arch/mips/alchemy/Kconfig"
-+source "arch/mips/ath25/Kconfig"
- source "arch/mips/ath79/Kconfig"
- source "arch/mips/bcm47xx/Kconfig"
- source "arch/mips/bcm63xx/Kconfig"
---- a/arch/mips/Kbuild.platforms
-+++ b/arch/mips/Kbuild.platforms
-@@ -2,6 +2,7 @@
- 
- platforms += alchemy
- platforms += ar7
-+platforms += ath25
- platforms += ath79
- platforms += bcm47xx
- platforms += bcm63xx
---- /dev/null
-+++ b/arch/mips/ath25/Platform
-@@ -0,0 +1,6 @@
-+#
-+# Atheros AR531X/AR231X WiSoC
-+#
-+platform-$(CONFIG_ATH25)	+= ath25/
-+cflags-$(CONFIG_ATH25)		+= -I$(srctree)/arch/mips/include/asm/mach-ath25
-+load-$(CONFIG_ATH25)		+= 0xffffffff80041000
---- /dev/null
-+++ b/arch/mips/ath25/Kconfig
-@@ -0,0 +1,9 @@
-+config SOC_AR5312
-+	bool "Atheros AR5312/AR2312+ SoC support"
-+	depends on ATH25
-+	default y
-+
-+config SOC_AR2315
-+	bool "Atheros AR2315+ SoC support"
-+	depends on ATH25
-+	default y
---- /dev/null
-+++ b/arch/mips/ath25/Makefile
-@@ -0,0 +1,13 @@
-+#
-+# This file is subject to the terms and conditions of the GNU General Public
-+# License.  See the file "COPYING" in the main directory of this archive
-+# for more details.
-+#
-+# Copyright (C) 2006 FON Technology, SL.
-+# Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+# Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
-+#
-+
-+obj-y += board.o prom.o devices.o
-+obj-$(CONFIG_SOC_AR5312) += ar5312.o
-+obj-$(CONFIG_SOC_AR2315) += ar2315.o
---- /dev/null
-+++ b/arch/mips/ath25/board.c
-@@ -0,0 +1,234 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
-+ * Copyright (C) 2006 FON Technology, SL.
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/interrupt.h>
-+#include <asm/irq_cpu.h>
-+#include <asm/reboot.h>
-+#include <asm/bootinfo.h>
-+#include <asm/time.h>
-+
-+#include <ath25_platform.h>
-+#include "devices.h"
-+#include "ar5312.h"
-+#include "ar2315.h"
-+
-+void (*ath25_irq_dispatch)(void);
-+
-+static inline bool check_radio_magic(const void __iomem *addr)
-+{
-+	addr += 0x7a; /* offset for flash magic */
-+	return (__raw_readb(addr) == 0x5a) && (__raw_readb(addr + 1) == 0xa5);
-+}
-+
-+static inline bool check_notempty(const void __iomem *addr)
-+{
-+	return __raw_readl(addr) != 0xffffffff;
-+}
-+
-+static inline bool check_board_data(const void __iomem *addr, bool broken)
-+{
-+	/* config magic found */
-+	if (__raw_readl(addr) == ATH25_BD_MAGIC)
-+		return true;
-+
-+	if (!broken)
-+		return false;
-+
-+	/* broken board data detected, use radio data to find the
-+	 * offset, user will fix this */
-+
-+	if (check_radio_magic(addr + 0x1000))
-+		return true;
-+	if (check_radio_magic(addr + 0xf8))
-+		return true;
-+
-+	return false;
-+}
-+
-+static const void __iomem * __init find_board_config(const void __iomem *limit,
-+						     const bool broken)
-+{
-+	const void __iomem *addr;
-+	const void __iomem *begin = limit - 0x1000;
-+	const void __iomem *end = limit - 0x30000;
-+
-+	for (addr = begin; addr >= end; addr -= 0x1000)
-+		if (check_board_data(addr, broken))
-+			return addr;
-+
-+	return NULL;
-+}
-+
-+static const void __iomem * __init find_radio_config(const void __iomem *limit,
-+						     const void __iomem *bcfg)
-+{
-+	const void __iomem *rcfg, *begin, *end;
-+
-+	/*
-+	 * Now find the start of Radio Configuration data, using heuristics:
-+	 * Search forward from Board Configuration data by 0x1000 bytes
-+	 * at a time until we find non-0xffffffff.
-+	 */
-+	begin = bcfg + 0x1000;
-+	end = limit;
-+	for (rcfg = begin; rcfg < end; rcfg += 0x1000)
-+		if (check_notempty(rcfg) && check_radio_magic(rcfg))
-+			return rcfg;
-+
-+	/* AR2316 relocates radio config to new location */
-+	begin = bcfg + 0xf8;
-+	end = limit - 0x1000 + 0xf8;
-+	for (rcfg = begin; rcfg < end; rcfg += 0x1000)
-+		if (check_notempty(rcfg) && check_radio_magic(rcfg))
-+			return rcfg;
-+
-+	return NULL;
-+}
-+
-+/*
-+ * NB: Search region size could be larger than the actual flash size,
-+ * but this shouldn't be a problem here, because the flash
-+ * will simply be mapped multiple times.
-+ */
-+int __init ath25_find_config(phys_addr_t base, unsigned long size)
-+{
-+	const void __iomem *flash_base, *flash_limit;
-+	struct ath25_boarddata *config;
-+	unsigned int rcfg_size;
-+	int broken_boarddata = 0;
-+	const void __iomem *bcfg, *rcfg;
-+	u8 *board_data;
-+	u8 *radio_data;
-+	u8 *mac_addr;
-+	u32 offset;
-+
-+	flash_base = ioremap_nocache(base, size);
-+	flash_limit = flash_base + size;
-+
-+	ath25_board.config = NULL;
-+	ath25_board.radio = NULL;
-+
-+	/* Copy the board and radio data to RAM, because accessing the mapped
-+	 * memory of the flash directly after booting is not safe */
-+
-+	/* Try to find valid board and radio data */
-+	bcfg = find_board_config(flash_limit, false);
-+
-+	/* If that fails, try to at least find valid radio data */
-+	if (!bcfg) {
-+		bcfg = find_board_config(flash_limit, true);
-+		broken_boarddata = 1;
-+	}
-+
-+	if (!bcfg) {
-+		pr_warn("WARNING: No board configuration data found!\n");
-+		goto error;
-+	}
-+
-+	board_data = kzalloc(BOARD_CONFIG_BUFSZ, GFP_KERNEL);
-+	ath25_board.config = (struct ath25_boarddata *)board_data;
-+	memcpy_fromio(board_data, bcfg, 0x100);
-+	if (broken_boarddata) {
-+		pr_warn("WARNING: broken board data detected\n");
-+		config = ath25_board.config;
-+		if (is_zero_ether_addr(config->enet0_mac)) {
-+			pr_info("Fixing up empty mac addresses\n");
-+			config->reset_config_gpio = 0xffff;
-+			config->sys_led_gpio = 0xffff;
-+			random_ether_addr(config->wlan0_mac);
-+			config->wlan0_mac[0] &= ~0x06;
-+			random_ether_addr(config->enet0_mac);
-+			random_ether_addr(config->enet1_mac);
-+		}
-+	}
-+
-+	/* Radio config starts 0x100 bytes after board config, regardless
-+	 * of what the physical layout on the flash chip looks like */
-+
-+	rcfg = find_radio_config(flash_limit, bcfg);
-+	if (!rcfg) {
-+		pr_warn("WARNING: Could not find Radio Configuration data\n");
-+		goto error;
-+	}
-+
-+	radio_data = board_data + 0x100 + ((rcfg - bcfg) & 0xfff);
-+	ath25_board.radio = radio_data;
-+	offset = radio_data - board_data;
-+	pr_info("Radio config found at offset 0x%x (0x%x)\n", rcfg - bcfg,
-+		offset);
-+	rcfg_size = BOARD_CONFIG_BUFSZ - offset;
-+	memcpy_fromio(radio_data, rcfg, rcfg_size);
-+
-+	mac_addr = &radio_data[0x1d * 2];
-+	if (is_broadcast_ether_addr(mac_addr)) {
-+		pr_info("Radio MAC is blank; using board-data\n");
-+		ether_addr_copy(mac_addr, ath25_board.config->wlan0_mac);
-+	}
-+
-+	iounmap(flash_base);
-+
-+	return 0;
-+
-+error:
-+	iounmap(flash_base);
-+	return -ENODEV;
-+}
-+
-+static void ath25_halt(void)
-+{
-+	local_irq_disable();
-+	unreachable();
-+}
-+
-+void __init plat_mem_setup(void)
-+{
-+	_machine_halt = ath25_halt;
-+	pm_power_off = ath25_halt;
-+
-+	if (is_ar5312())
-+		ar5312_plat_mem_setup();
-+	else
-+		ar2315_plat_mem_setup();
-+
-+	/* Disable data watchpoints */
-+	write_c0_watchlo0(0);
-+}
-+
-+asmlinkage void plat_irq_dispatch(void)
-+{
-+	ath25_irq_dispatch();
-+}
-+
-+void __init plat_time_init(void)
-+{
-+	if (is_ar5312())
-+		ar5312_plat_time_init();
-+	else
-+		ar2315_plat_time_init();
-+}
-+
-+unsigned int __cpuinit get_c0_compare_int(void)
-+{
-+	return CP0_LEGACY_COMPARE_IRQ;
-+}
-+
-+void __init arch_init_irq(void)
-+{
-+	clear_c0_status(ST0_IM);
-+	mips_cpu_irq_init();
-+
-+	/* Initialize interrupt controllers */
-+	if (is_ar5312())
-+		ar5312_arch_init_irq();
-+	else
-+		ar2315_arch_init_irq();
-+}
---- /dev/null
-+++ b/arch/mips/ath25/prom.c
-@@ -0,0 +1,26 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright MontaVista Software Inc
-+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
-+ * Copyright (C) 2006 FON Technology, SL.
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
-+ */
-+
-+/*
-+ * Prom setup file for AR5312/AR231x SoCs
-+ */
-+
-+#include <linux/init.h>
-+#include <asm/bootinfo.h>
-+
-+void __init prom_init(void)
-+{
-+}
-+
-+void __init prom_free_prom_memory(void)
-+{
-+}
---- /dev/null
-+++ b/arch/mips/include/asm/mach-ath25/ath25_platform.h
-@@ -0,0 +1,73 @@
-+#ifndef __ASM_MACH_ATH25_PLATFORM_H
-+#define __ASM_MACH_ATH25_PLATFORM_H
-+
-+#include <linux/etherdevice.h>
-+
-+/*
-+ * This is board-specific data that is stored in a "fixed" location in flash.
-+ * It is shared across operating systems, so it should not be changed lightly.
-+ * The main reason we need it is in order to extract the ethernet MAC
-+ * address(es).
-+ */
-+struct ath25_boarddata {
-+	u32 magic;                   /* board data is valid */
-+#define ATH25_BD_MAGIC 0x35333131    /* "5311", for all 531x/231x platforms */
-+	u16 cksum;                   /* checksum (starting with BD_REV 2) */
-+	u16 rev;                     /* revision of this struct */
-+#define BD_REV 4
-+	char board_name[64];         /* Name of board */
-+	u16 major;                   /* Board major number */
-+	u16 minor;                   /* Board minor number */
-+	u32 flags;                   /* Board configuration */
-+#define BD_ENET0        0x00000001   /* ENET0 is stuffed */
-+#define BD_ENET1        0x00000002   /* ENET1 is stuffed */
-+#define BD_UART1        0x00000004   /* UART1 is stuffed */
-+#define BD_UART0        0x00000008   /* UART0 is stuffed (dma) */
-+#define BD_RSTFACTORY   0x00000010   /* Reset factory defaults stuffed */
-+#define BD_SYSLED       0x00000020   /* System LED stuffed */
-+#define BD_EXTUARTCLK   0x00000040   /* External UART clock */
-+#define BD_CPUFREQ      0x00000080   /* cpu freq is valid in nvram */
-+#define BD_SYSFREQ      0x00000100   /* sys freq is set in nvram */
-+#define BD_WLAN0        0x00000200   /* Enable WLAN0 */
-+#define BD_MEMCAP       0x00000400   /* CAP SDRAM @ mem_cap for testing */
-+#define BD_DISWATCHDOG  0x00000800   /* disable system watchdog */
-+#define BD_WLAN1        0x00001000   /* Enable WLAN1 (ar5212) */
-+#define BD_ISCASPER     0x00002000   /* FLAG for AR2312 */
-+#define BD_WLAN0_2G_EN  0x00004000   /* FLAG for radio0_2G */
-+#define BD_WLAN0_5G_EN  0x00008000   /* FLAG for radio0_2G */
-+#define BD_WLAN1_2G_EN  0x00020000   /* FLAG for radio0_2G */
-+#define BD_WLAN1_5G_EN  0x00040000   /* FLAG for radio0_2G */
-+	u16 reset_config_gpio;       /* Reset factory GPIO pin */
-+	u16 sys_led_gpio;            /* System LED GPIO pin */
-+
-+	u32 cpu_freq;                /* CPU core frequency in Hz */
-+	u32 sys_freq;                /* System frequency in Hz */
-+	u32 cnt_freq;                /* Calculated C0_COUNT frequency */
-+
-+	u8  wlan0_mac[ETH_ALEN];
-+	u8  enet0_mac[ETH_ALEN];
-+	u8  enet1_mac[ETH_ALEN];
-+
-+	u16 pci_id;                  /* Pseudo PCIID for common code */
-+	u16 mem_cap;                 /* cap bank1 in MB */
-+
-+	/* version 3 */
-+	u8  wlan1_mac[ETH_ALEN];     /* (ar5212) */
-+};
-+
-+#define BOARD_CONFIG_BUFSZ		0x1000
-+
-+/*
-+ * Platform device information for the Wireless MAC
-+ */
-+struct ar231x_board_config {
-+	u16 devid;
-+
-+	/* board config data */
-+	struct ath25_boarddata *config;
-+
-+	/* radio calibration data */
-+	const char *radio;
-+};
-+
-+#endif /* __ASM_MACH_ATH25_PLATFORM_H */
---- /dev/null
-+++ b/arch/mips/include/asm/mach-ath25/cpu-feature-overrides.h
-@@ -0,0 +1,64 @@
-+/*
-+ *  Atheros AR231x/AR531x SoC specific CPU feature overrides
-+ *
-+ *  Copyright (C) 2008 Gabor Juhos <juhosg@openwrt.org>
-+ *
-+ *  This file was derived from: include/asm-mips/cpu-features.h
-+ *	Copyright (C) 2003, 2004 Ralf Baechle
-+ *	Copyright (C) 2004 Maciej W. Rozycki
-+ *
-+ *  This program is free software; you can redistribute it and/or modify it
-+ *  under the terms of the GNU General Public License version 2 as published
-+ *  by the Free Software Foundation.
-+ *
-+ */
-+#ifndef __ASM_MACH_ATH25_CPU_FEATURE_OVERRIDES_H
-+#define __ASM_MACH_ATH25_CPU_FEATURE_OVERRIDES_H
-+
-+/*
-+ * The Atheros AR531x/AR231x SoCs have MIPS 4Kc/4KEc core.
-+ */
-+#define cpu_has_tlb			1
-+#define cpu_has_4kex			1
-+#define cpu_has_3k_cache		0
-+#define cpu_has_4k_cache		1
-+#define cpu_has_tx39_cache		0
-+#define cpu_has_sb1_cache		0
-+#define cpu_has_fpu			0
-+#define cpu_has_32fpr			0
-+#define cpu_has_counter			1
-+#define cpu_has_ejtag			1
-+
-+#if !defined(CONFIG_SOC_AR5312)
-+#  define cpu_has_llsc			1
-+#else
-+/*
-+ * The MIPS 4Kc V0.9 core in the AR5312/AR2312 have problems with the
-+ * ll/sc instructions.
-+ */
-+#  define cpu_has_llsc			0
-+#endif
-+
-+#define cpu_has_mips16			0
-+#define cpu_has_mdmx			0
-+#define cpu_has_mips3d			0
-+#define cpu_has_smartmips		0
-+
-+#define cpu_has_mips32r1		1
-+
-+#if !defined(CONFIG_SOC_AR5312)
-+#  define cpu_has_mips32r2		1
-+#endif
-+
-+#define cpu_has_mips64r1		0
-+#define cpu_has_mips64r2		0
-+
-+#define cpu_has_dsp			0
-+#define cpu_has_mipsmt			0
-+
-+#define cpu_has_64bits			0
-+#define cpu_has_64bit_zero_reg		0
-+#define cpu_has_64bit_gp_regs		0
-+#define cpu_has_64bit_addresses		0
-+
-+#endif /* __ASM_MACH_ATH25_CPU_FEATURE_OVERRIDES_H */
---- /dev/null
-+++ b/arch/mips/include/asm/mach-ath25/dma-coherence.h
-@@ -0,0 +1,82 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2006  Ralf Baechle <ralf@linux-mips.org>
-+ * Copyright (C) 2007  Felix Fietkau <nbd@openwrt.org>
-+ *
-+ */
-+#ifndef __ASM_MACH_ATH25_DMA_COHERENCE_H
-+#define __ASM_MACH_ATH25_DMA_COHERENCE_H
-+
-+#include <linux/device.h>
-+
-+/*
-+ * We need some arbitrary non-zero value to be programmed to the BAR1 register
-+ * of PCI host controller to enable DMA. The same value should be used as the
-+ * offset to calculate the physical address of DMA buffer for PCI devices.
-+ */
-+#define AR2315_PCI_HOST_SDRAM_BASEADDR	0x20000000
-+
-+static inline dma_addr_t ath25_dev_offset(struct device *dev)
-+{
-+#ifdef CONFIG_PCI
-+	extern struct bus_type pci_bus_type;
-+
-+	if (dev && dev->bus == &pci_bus_type)
-+		return AR2315_PCI_HOST_SDRAM_BASEADDR;
-+#endif
-+	return 0;
-+}
-+
-+static inline dma_addr_t
-+plat_map_dma_mem(struct device *dev, void *addr, size_t size)
-+{
-+	return virt_to_phys(addr) + ath25_dev_offset(dev);
-+}
-+
-+static inline dma_addr_t
-+plat_map_dma_mem_page(struct device *dev, struct page *page)
-+{
-+	return page_to_phys(page) + ath25_dev_offset(dev);
-+}
-+
-+static inline unsigned long
-+plat_dma_addr_to_phys(struct device *dev, dma_addr_t dma_addr)
-+{
-+	return dma_addr - ath25_dev_offset(dev);
-+}
-+
-+static inline void
-+plat_unmap_dma_mem(struct device *dev, dma_addr_t dma_addr, size_t size,
-+		   enum dma_data_direction direction)
-+{
-+}
-+
-+static inline int plat_dma_supported(struct device *dev, u64 mask)
-+{
-+	return 1;
-+}
-+
-+static inline void plat_extra_sync_for_device(struct device *dev)
-+{
-+}
-+
-+static inline int plat_dma_mapping_error(struct device *dev,
-+					 dma_addr_t dma_addr)
-+{
-+	return 0;
-+}
-+
-+static inline int plat_device_is_coherent(struct device *dev)
-+{
-+#ifdef CONFIG_DMA_COHERENT
-+	return 1;
-+#endif
-+#ifdef CONFIG_DMA_NONCOHERENT
-+	return 0;
-+#endif
-+}
-+
-+#endif /* __ASM_MACH_ATH25_DMA_COHERENCE_H */
---- /dev/null
-+++ b/arch/mips/include/asm/mach-ath25/gpio.h
-@@ -0,0 +1,16 @@
-+#ifndef __ASM_MACH_ATH25_GPIO_H
-+#define __ASM_MACH_ATH25_GPIO_H
-+
-+#include <asm-generic/gpio.h>
-+
-+#define gpio_get_value __gpio_get_value
-+#define gpio_set_value __gpio_set_value
-+#define gpio_cansleep __gpio_cansleep
-+#define gpio_to_irq __gpio_to_irq
-+
-+static inline int irq_to_gpio(unsigned irq)
-+{
-+	return -EINVAL;
-+}
-+
-+#endif	/* __ASM_MACH_ATH25_GPIO_H */
---- /dev/null
-+++ b/arch/mips/include/asm/mach-ath25/war.h
-@@ -0,0 +1,25 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2008 Felix Fietkau <nbd@openwrt.org>
-+ */
-+#ifndef __ASM_MACH_ATH25_WAR_H
-+#define __ASM_MACH_ATH25_WAR_H
-+
-+#define R4600_V1_INDEX_ICACHEOP_WAR	0
-+#define R4600_V1_HIT_CACHEOP_WAR	0
-+#define R4600_V2_HIT_CACHEOP_WAR	0
-+#define R5432_CP0_INTERRUPT_WAR		0
-+#define BCM1250_M3_WAR			0
-+#define SIBYTE_1956_WAR			0
-+#define MIPS4K_ICACHE_REFILL_WAR	0
-+#define MIPS_CACHE_SYNC_WAR		0
-+#define TX49XX_ICACHE_INDEX_INV_WAR	0
-+#define RM9000_CDEX_SMP_WAR		0
-+#define ICACHE_REFILLS_WORKAROUND_WAR	0
-+#define R10000_LLSC_WAR			0
-+#define MIPS34K_MISSED_ITLB_WAR		0
-+
-+#endif /* __ASM_MACH_ATH25_WAR_H */
---- /dev/null
-+++ b/arch/mips/ath25/ar2315_regs.h
-@@ -0,0 +1,410 @@
-+/*
-+ * Register definitions for AR2315+
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
-+ * Copyright (C) 2006 FON Technology, SL.
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2008 Felix Fietkau <nbd@openwrt.org>
-+ */
-+
-+#ifndef __ASM_MACH_ATH25_AR2315_REGS_H
-+#define __ASM_MACH_ATH25_AR2315_REGS_H
-+
-+/*
-+ * IRQs
-+ */
-+#define AR2315_IRQ_MISC		(MIPS_CPU_IRQ_BASE + 2)	/* C0_CAUSE: 0x0400 */
-+#define AR2315_IRQ_WLAN0	(MIPS_CPU_IRQ_BASE + 3)	/* C0_CAUSE: 0x0800 */
-+#define AR2315_IRQ_ENET0	(MIPS_CPU_IRQ_BASE + 4)	/* C0_CAUSE: 0x1000 */
-+#define AR2315_IRQ_LCBUS_PCI	(MIPS_CPU_IRQ_BASE + 5)	/* C0_CAUSE: 0x2000 */
-+#define AR2315_IRQ_WLAN0_POLL	(MIPS_CPU_IRQ_BASE + 6)	/* C0_CAUSE: 0x4000 */
-+
-+/*
-+ * Miscellaneous interrupts, which share IP2.
-+ */
-+#define AR2315_MISC_IRQ_UART0		0
-+#define AR2315_MISC_IRQ_I2C_RSVD	1
-+#define AR2315_MISC_IRQ_SPI		2
-+#define AR2315_MISC_IRQ_AHB		3
-+#define AR2315_MISC_IRQ_APB		4
-+#define AR2315_MISC_IRQ_TIMER		5
-+#define AR2315_MISC_IRQ_GPIO		6
-+#define AR2315_MISC_IRQ_WATCHDOG	7
-+#define AR2315_MISC_IRQ_IR_RSVD		8
-+#define AR2315_MISC_IRQ_COUNT		9
-+
-+/*
-+ * Address map
-+ */
-+#define AR2315_SPI_READ_BASE	0x08000000	/* SPI flash */
-+#define AR2315_SPI_READ_SIZE	0x01000000
-+#define AR2315_WLAN0_BASE	0x10000000	/* Wireless MMR */
-+#define AR2315_PCI_BASE		0x10100000	/* PCI MMR */
-+#define AR2315_PCI_SIZE		0x00001000
-+#define AR2315_SDRAMCTL_BASE	0x10300000	/* SDRAM MMR */
-+#define AR2315_SDRAMCTL_SIZE	0x00000020
-+#define AR2315_LOCAL_BASE	0x10400000	/* Local bus MMR */
-+#define AR2315_ENET0_BASE	0x10500000	/* Ethernet MMR */
-+#define AR2315_RST_BASE		0x11000000	/* Reset control MMR */
-+#define AR2315_RST_SIZE		0x00000100
-+#define AR2315_UART0_BASE	0x11100000	/* UART MMR */
-+#define AR2315_SPI_MMR_BASE	0x11300000	/* SPI flash MMR */
-+#define AR2315_SPI_MMR_SIZE	0x00000010
-+#define AR2315_PCI_EXT_BASE	0x80000000	/* PCI external */
-+#define AR2315_PCI_EXT_SIZE	0x40000000
-+
-+/*
-+ * Configuration registers
-+ */
-+
-+/* Cold reset register */
-+#define AR2315_COLD_RESET		0x0000
-+
-+#define AR2315_RESET_COLD_AHB		0x00000001
-+#define AR2315_RESET_COLD_APB		0x00000002
-+#define AR2315_RESET_COLD_CPU		0x00000004
-+#define AR2315_RESET_COLD_CPUWARM	0x00000008
-+#define AR2315_RESET_SYSTEM		(RESET_COLD_CPU |\
-+					 RESET_COLD_APB |\
-+					 RESET_COLD_AHB)  /* full system */
-+#define AR2317_RESET_SYSTEM		0x00000010
-+
-+/* Reset register */
-+#define AR2315_RESET			0x0004
-+
-+#define AR2315_RESET_WARM_WLAN0_MAC	0x00000001  /* warm reset WLAN0 MAC */
-+#define AR2315_RESET_WARM_WLAN0_BB	0x00000002  /* warm reset WLAN0 BB */
-+#define AR2315_RESET_MPEGTS_RSVD	0x00000004  /* warm reset MPEG-TS */
-+#define AR2315_RESET_PCIDMA		0x00000008  /* warm reset PCI ahb/dma */
-+#define AR2315_RESET_MEMCTL		0x00000010  /* warm reset mem control */
-+#define AR2315_RESET_LOCAL		0x00000020  /* warm reset local bus */
-+#define AR2315_RESET_I2C_RSVD		0x00000040  /* warm reset I2C bus */
-+#define AR2315_RESET_SPI		0x00000080  /* warm reset SPI iface */
-+#define AR2315_RESET_UART0		0x00000100  /* warm reset UART0 */
-+#define AR2315_RESET_IR_RSVD		0x00000200  /* warm reset IR iface */
-+#define AR2315_RESET_EPHY0		0x00000400  /* cold reset ENET0 phy */
-+#define AR2315_RESET_ENET0		0x00000800  /* cold reset ENET0 MAC */
-+
-+/* AHB master arbitration control */
-+#define AR2315_AHB_ARB_CTL		0x0008
-+
-+#define AR2315_ARB_CPU			0x00000001  /* CPU, default */
-+#define AR2315_ARB_WLAN			0x00000002  /* WLAN */
-+#define AR2315_ARB_MPEGTS_RSVD		0x00000004  /* MPEG-TS */
-+#define AR2315_ARB_LOCAL		0x00000008  /* Local bus */
-+#define AR2315_ARB_PCI			0x00000010  /* PCI bus */
-+#define AR2315_ARB_ETHERNET		0x00000020  /* Ethernet */
-+#define AR2315_ARB_RETRY		0x00000100  /* Retry policy (debug) */
-+
-+/* Config Register */
-+#define AR2315_ENDIAN_CTL		0x000c
-+
-+#define AR2315_CONFIG_AHB		0x00000001  /* EC-AHB bridge endian */
-+#define AR2315_CONFIG_WLAN		0x00000002  /* WLAN byteswap */
-+#define AR2315_CONFIG_MPEGTS_RSVD	0x00000004  /* MPEG-TS byteswap */
-+#define AR2315_CONFIG_PCI		0x00000008  /* PCI byteswap */
-+#define AR2315_CONFIG_MEMCTL		0x00000010  /* Mem controller endian */
-+#define AR2315_CONFIG_LOCAL		0x00000020  /* Local bus byteswap */
-+#define AR2315_CONFIG_ETHERNET		0x00000040  /* Ethernet byteswap */
-+#define AR2315_CONFIG_MERGE		0x00000200  /* CPU write buffer merge */
-+#define AR2315_CONFIG_CPU		0x00000400  /* CPU big endian */
-+#define AR2315_CONFIG_BIG		0x00000400
-+#define AR2315_CONFIG_PCIAHB		0x00000800
-+#define AR2315_CONFIG_PCIAHB_BRIDGE	0x00001000
-+#define AR2315_CONFIG_SPI		0x00008000  /* SPI byteswap */
-+#define AR2315_CONFIG_CPU_DRAM		0x00010000
-+#define AR2315_CONFIG_CPU_PCI		0x00020000
-+#define AR2315_CONFIG_CPU_MMR		0x00040000
-+
-+/* NMI control */
-+#define AR2315_NMI_CTL			0x0010
-+
-+#define AR2315_NMI_EN			1
-+
-+/* Revision Register - Initial value is 0x3010 (WMAC 3.0, AR231X 1.0). */
-+#define AR2315_SREV			0x0014
-+
-+#define AR2315_REV_MAJ			0x000000f0
-+#define AR2315_REV_MAJ_S		4
-+#define AR2315_REV_MIN			0x0000000f
-+#define AR2315_REV_MIN_S		0
-+#define AR2315_REV_CHIP			(AR2315_REV_MAJ | AR2315_REV_MIN)
-+
-+/* Interface Enable */
-+#define AR2315_IF_CTL			0x0018
-+
-+#define AR2315_IF_MASK			0x00000007
-+#define AR2315_IF_DISABLED		0		/* Disable all */
-+#define AR2315_IF_PCI			1		/* PCI */
-+#define AR2315_IF_TS_LOCAL		2		/* Local bus */
-+#define AR2315_IF_ALL			3		/* Emulation only */
-+#define AR2315_IF_LOCAL_HOST		0x00000008
-+#define AR2315_IF_PCI_HOST		0x00000010
-+#define AR2315_IF_PCI_INTR		0x00000020
-+#define AR2315_IF_PCI_CLK_MASK		0x00030000
-+#define AR2315_IF_PCI_CLK_INPUT		0
-+#define AR2315_IF_PCI_CLK_OUTPUT_LOW	1
-+#define AR2315_IF_PCI_CLK_OUTPUT_CLK	2
-+#define AR2315_IF_PCI_CLK_OUTPUT_HIGH	3
-+#define AR2315_IF_PCI_CLK_SHIFT		16
-+
-+/* APB Interrupt control */
-+#define AR2315_ISR			0x0020
-+#define AR2315_IMR			0x0024
-+#define AR2315_GISR			0x0028
-+
-+#define AR2315_ISR_UART0	0x00000001	/* high speed UART */
-+#define AR2315_ISR_I2C_RSVD	0x00000002	/* I2C bus */
-+#define AR2315_ISR_SPI		0x00000004	/* SPI bus */
-+#define AR2315_ISR_AHB		0x00000008	/* AHB error */
-+#define AR2315_ISR_APB		0x00000010	/* APB error */
-+#define AR2315_ISR_TIMER	0x00000020	/* Timer */
-+#define AR2315_ISR_GPIO		0x00000040	/* GPIO */
-+#define AR2315_ISR_WD		0x00000080	/* Watchdog */
-+#define AR2315_ISR_IR_RSVD	0x00000100	/* IR */
-+
-+#define AR2315_GISR_MISC	0x00000001	/* Misc */
-+#define AR2315_GISR_WLAN0	0x00000002	/* WLAN0 */
-+#define AR2315_GISR_MPEGTS_RSVD	0x00000004	/* MPEG-TS */
-+#define AR2315_GISR_LOCALPCI	0x00000008	/* Local/PCI bus */
-+#define AR2315_GISR_WMACPOLL	0x00000010
-+#define AR2315_GISR_TIMER	0x00000020
-+#define AR2315_GISR_ETHERNET	0x00000040	/* Ethernet */
-+
-+/* Generic timer */
-+#define AR2315_TIMER			0x0030
-+#define AR2315_RELOAD			0x0034
-+
-+/* Watchdog timer */
-+#define AR2315_WDT_TIMER		0x0038
-+#define AR2315_WDT_CTRL			0x003c
-+
-+#define AR2315_WDT_CTRL_IGNORE	0x00000000	/* ignore expiration */
-+#define AR2315_WDT_CTRL_NMI	0x00000001	/* NMI on watchdog */
-+#define AR2315_WDT_CTRL_RESET	0x00000002	/* reset on watchdog */
-+
-+/* CPU Performance Counters */
-+#define AR2315_PERFCNT0			0x0048
-+#define AR2315_PERFCNT1			0x004c
-+
-+#define AR2315_PERF0_DATAHIT	0x00000001  /* Count Data Cache Hits */
-+#define AR2315_PERF0_DATAMISS	0x00000002  /* Count Data Cache Misses */
-+#define AR2315_PERF0_INSTHIT	0x00000004  /* Count Instruction Cache Hits */
-+#define AR2315_PERF0_INSTMISS	0x00000008  /* Count Instruction Cache Misses */
-+#define AR2315_PERF0_ACTIVE	0x00000010  /* Count Active Processor Cycles */
-+#define AR2315_PERF0_WBHIT	0x00000020  /* Count CPU Write Buffer Hits */
-+#define AR2315_PERF0_WBMISS	0x00000040  /* Count CPU Write Buffer Misses */
-+
-+#define AR2315_PERF1_EB_ARDY	0x00000001  /* Count EB_ARdy signal */
-+#define AR2315_PERF1_EB_AVALID	0x00000002  /* Count EB_AValid signal */
-+#define AR2315_PERF1_EB_WDRDY	0x00000004  /* Count EB_WDRdy signal */
-+#define AR2315_PERF1_EB_RDVAL	0x00000008  /* Count EB_RdVal signal */
-+#define AR2315_PERF1_VRADDR	0x00000010  /* Count valid read address cycles*/
-+#define AR2315_PERF1_VWADDR	0x00000020  /* Count valid write address cycl.*/
-+#define AR2315_PERF1_VWDATA	0x00000040  /* Count valid write data cycles */
-+
-+/* AHB Error Reporting */
-+#define AR2315_AHB_ERR0			0x0050  /* error  */
-+#define AR2315_AHB_ERR1			0x0054  /* haddr  */
-+#define AR2315_AHB_ERR2			0x0058  /* hwdata */
-+#define AR2315_AHB_ERR3			0x005c  /* hrdata */
-+#define AR2315_AHB_ERR4			0x0060  /* status */
-+
-+#define AR2315_AHB_ERROR_DET	1 /* AHB Error has been detected,          */
-+				  /* write 1 to clear all bits in ERR0     */
-+#define AR2315_AHB_ERROR_OVR	2 /* AHB Error overflow has been detected  */
-+#define AR2315_AHB_ERROR_WDT	4 /* AHB Error due to wdt instead of hresp */
-+
-+#define AR2315_PROCERR_HMAST		0x0000000f
-+#define AR2315_PROCERR_HMAST_DFLT	0
-+#define AR2315_PROCERR_HMAST_WMAC	1
-+#define AR2315_PROCERR_HMAST_ENET	2
-+#define AR2315_PROCERR_HMAST_PCIENDPT	3
-+#define AR2315_PROCERR_HMAST_LOCAL	4
-+#define AR2315_PROCERR_HMAST_CPU	5
-+#define AR2315_PROCERR_HMAST_PCITGT	6
-+#define AR2315_PROCERR_HMAST_S		0
-+#define AR2315_PROCERR_HWRITE		0x00000010
-+#define AR2315_PROCERR_HSIZE		0x00000060
-+#define AR2315_PROCERR_HSIZE_S		5
-+#define AR2315_PROCERR_HTRANS		0x00000180
-+#define AR2315_PROCERR_HTRANS_S		7
-+#define AR2315_PROCERR_HBURST		0x00000e00
-+#define AR2315_PROCERR_HBURST_S		9
-+
-+/* Clock Control */
-+#define AR2315_PLLC_CTL			0x0064
-+#define AR2315_PLLV_CTL			0x0068
-+#define AR2315_CPUCLK			0x006c
-+#define AR2315_AMBACLK			0x0070
-+#define AR2315_SYNCCLK			0x0074
-+#define AR2315_DSL_SLEEP_CTL		0x0080
-+#define AR2315_DSL_SLEEP_DUR		0x0084
-+
-+/* PLLc Control fields */
-+#define AR2315_PLLC_REF_DIV_M		0x00000003
-+#define AR2315_PLLC_REF_DIV_S		0
-+#define AR2315_PLLC_FDBACK_DIV_M	0x0000007c
-+#define AR2315_PLLC_FDBACK_DIV_S	2
-+#define AR2315_PLLC_ADD_FDBACK_DIV_M	0x00000080
-+#define AR2315_PLLC_ADD_FDBACK_DIV_S	7
-+#define AR2315_PLLC_CLKC_DIV_M		0x0001c000
-+#define AR2315_PLLC_CLKC_DIV_S		14
-+#define AR2315_PLLC_CLKM_DIV_M		0x00700000
-+#define AR2315_PLLC_CLKM_DIV_S		20
-+
-+/* CPU CLK Control fields */
-+#define AR2315_CPUCLK_CLK_SEL_M		0x00000003
-+#define AR2315_CPUCLK_CLK_SEL_S		0
-+#define AR2315_CPUCLK_CLK_DIV_M		0x0000000c
-+#define AR2315_CPUCLK_CLK_DIV_S		2
-+
-+/* AMBA CLK Control fields */
-+#define AR2315_AMBACLK_CLK_SEL_M	0x00000003
-+#define AR2315_AMBACLK_CLK_SEL_S	0
-+#define AR2315_AMBACLK_CLK_DIV_M	0x0000000c
-+#define AR2315_AMBACLK_CLK_DIV_S	2
-+
-+/* PCI Clock Control */
-+#define AR2315_PCICLK			0x00a4
-+
-+#define AR2315_PCICLK_INPUT_M		0x00000003
-+#define AR2315_PCICLK_INPUT_S		0
-+#define AR2315_PCICLK_PLLC_CLKM		0
-+#define AR2315_PCICLK_PLLC_CLKM1	1
-+#define AR2315_PCICLK_PLLC_CLKC		2
-+#define AR2315_PCICLK_REF_CLK		3
-+#define AR2315_PCICLK_DIV_M		0x0000000c
-+#define AR2315_PCICLK_DIV_S		2
-+#define AR2315_PCICLK_IN_FREQ		0
-+#define AR2315_PCICLK_IN_FREQ_DIV_6	1
-+#define AR2315_PCICLK_IN_FREQ_DIV_8	2
-+#define AR2315_PCICLK_IN_FREQ_DIV_10	3
-+
-+/* Observation Control Register */
-+#define AR2315_OCR			0x00b0
-+
-+#define AR2315_OCR_GPIO0_IRIN		0x00000040
-+#define AR2315_OCR_GPIO1_IROUT		0x00000080
-+#define AR2315_OCR_GPIO3_RXCLR		0x00000200
-+
-+/* General Clock Control */
-+#define AR2315_MISCCLK			0x00b4
-+
-+#define AR2315_MISCCLK_PLLBYPASS_EN	0x00000001
-+#define AR2315_MISCCLK_PROCREFCLK	0x00000002
-+
-+/*
-+ * SDRAM Controller
-+ *   - No read or write buffers are included.
-+ */
-+#define AR2315_MEM_CFG			0x0000
-+#define AR2315_MEM_CTRL			0x000c
-+#define AR2315_MEM_REF			0x0010
-+
-+#define AR2315_MEM_CFG_DATA_WIDTH_M	0x00006000
-+#define AR2315_MEM_CFG_DATA_WIDTH_S	13
-+#define AR2315_MEM_CFG_COL_WIDTH_M	0x00001e00
-+#define AR2315_MEM_CFG_COL_WIDTH_S	9
-+#define AR2315_MEM_CFG_ROW_WIDTH_M	0x000001e0
-+#define AR2315_MEM_CFG_ROW_WIDTH_S	5
-+#define AR2315_MEM_CFG_BANKADDR_BITS_M	0x00000018
-+#define AR2315_MEM_CFG_BANKADDR_BITS_S	3
-+
-+/*
-+ * Local Bus Interface Registers
-+ */
-+#define AR2315_LB_CONFIG		0x0000
-+
-+#define AR2315_LBCONF_OE	0x00000001	/* =1 OE is low-true */
-+#define AR2315_LBCONF_CS0	0x00000002	/* =1 first CS is low-true */
-+#define AR2315_LBCONF_CS1	0x00000004	/* =1 2nd CS is low-true */
-+#define AR2315_LBCONF_RDY	0x00000008	/* =1 RDY is low-true */
-+#define AR2315_LBCONF_WE	0x00000010	/* =1 Write En is low-true */
-+#define AR2315_LBCONF_WAIT	0x00000020	/* =1 WAIT is low-true */
-+#define AR2315_LBCONF_ADS	0x00000040	/* =1 Adr Strobe is low-true */
-+#define AR2315_LBCONF_MOT	0x00000080	/* =0 Intel, =1 Motorola */
-+#define AR2315_LBCONF_8CS	0x00000100	/* =1 8 bits CS, 0= 16bits */
-+#define AR2315_LBCONF_8DS	0x00000200	/* =1 8 bits Data S, 0=16bits */
-+#define AR2315_LBCONF_ADS_EN	0x00000400	/* =1 Enable ADS */
-+#define AR2315_LBCONF_ADR_OE	0x00000800	/* =1 Adr cap on OE, WE or DS */
-+#define AR2315_LBCONF_ADDT_MUX	0x00001000	/* =1 Adr and Data share bus */
-+#define AR2315_LBCONF_DATA_OE	0x00002000	/* =1 Data cap on OE, WE, DS */
-+#define AR2315_LBCONF_16DATA	0x00004000	/* =1 Data is 16 bits wide */
-+#define AR2315_LBCONF_SWAPDT	0x00008000	/* =1 Byte swap data */
-+#define AR2315_LBCONF_SYNC	0x00010000	/* =1 Bus synchronous to clk */
-+#define AR2315_LBCONF_INT	0x00020000	/* =1 Intr is low true */
-+#define AR2315_LBCONF_INT_CTR0	0x00000000	/* GND high-Z, Vdd is high-Z */
-+#define AR2315_LBCONF_INT_CTR1	0x00040000	/* GND drive, Vdd is high-Z */
-+#define AR2315_LBCONF_INT_CTR2	0x00080000	/* GND high-Z, Vdd drive */
-+#define AR2315_LBCONF_INT_CTR3	0x000c0000	/* GND drive, Vdd drive */
-+#define AR2315_LBCONF_RDY_WAIT	0x00100000	/* =1 RDY is negative of WAIT */
-+#define AR2315_LBCONF_INT_PULSE	0x00200000	/* =1 Interrupt is a pulse */
-+#define AR2315_LBCONF_ENABLE	0x00400000	/* =1 Falcon respond to LB */
-+
-+#define AR2315_LB_CLKSEL		0x0004
-+
-+#define AR2315_LBCLK_EXT	0x00000001	/* use external clk for lb */
-+
-+#define AR2315_LB_1MS			0x0008
-+
-+#define AR2315_LB1MS_MASK	0x0003ffff	/* # of AHB clk cycles in 1ms */
-+
-+#define AR2315_LB_MISCCFG		0x000c
-+
-+#define AR2315_LBM_TXD_EN	0x00000001	/* Enable TXD for fragments */
-+#define AR2315_LBM_RX_INTEN	0x00000002	/* Enable LB ints on RX ready */
-+#define AR2315_LBM_MBOXWR_INTEN	0x00000004	/* Enable LB ints on mbox wr */
-+#define AR2315_LBM_MBOXRD_INTEN	0x00000008	/* Enable LB ints on mbox rd */
-+#define AR2315_LMB_DESCSWAP_EN	0x00000010	/* Byte swap desc enable */
-+#define AR2315_LBM_TIMEOUT_M	0x00ffff80
-+#define AR2315_LBM_TIMEOUT_S	7
-+#define AR2315_LBM_PORTMUX	0x07000000
-+
-+#define AR2315_LB_RXTSOFF		0x0010
-+
-+#define AR2315_LB_TX_CHAIN_EN		0x0100
-+
-+#define AR2315_LB_TXEN_0	0x00000001
-+#define AR2315_LB_TXEN_1	0x00000002
-+#define AR2315_LB_TXEN_2	0x00000004
-+#define AR2315_LB_TXEN_3	0x00000008
-+
-+#define AR2315_LB_TX_CHAIN_DIS		0x0104
-+#define AR2315_LB_TX_DESC_PTR		0x0200
-+
-+#define AR2315_LB_RX_CHAIN_EN		0x0400
-+
-+#define AR2315_LB_RXEN		0x00000001
-+
-+#define AR2315_LB_RX_CHAIN_DIS		0x0404
-+#define AR2315_LB_RX_DESC_PTR		0x0408
-+
-+#define AR2315_LB_INT_STATUS		0x0500
-+
-+#define AR2315_LB_INT_TX_DESC		0x00000001
-+#define AR2315_LB_INT_TX_OK		0x00000002
-+#define AR2315_LB_INT_TX_ERR		0x00000004
-+#define AR2315_LB_INT_TX_EOF		0x00000008
-+#define AR2315_LB_INT_RX_DESC		0x00000010
-+#define AR2315_LB_INT_RX_OK		0x00000020
-+#define AR2315_LB_INT_RX_ERR		0x00000040
-+#define AR2315_LB_INT_RX_EOF		0x00000080
-+#define AR2315_LB_INT_TX_TRUNC		0x00000100
-+#define AR2315_LB_INT_TX_STARVE		0x00000200
-+#define AR2315_LB_INT_LB_TIMEOUT	0x00000400
-+#define AR2315_LB_INT_LB_ERR		0x00000800
-+#define AR2315_LB_INT_MBOX_WR		0x00001000
-+#define AR2315_LB_INT_MBOX_RD		0x00002000
-+
-+/* Bit definitions for INT MASK are the same as INT_STATUS */
-+#define AR2315_LB_INT_MASK		0x0504
-+
-+#define AR2315_LB_INT_EN		0x0508
-+#define AR2315_LB_MBOX			0x0600
-+
-+#endif /* __ASM_MACH_ATH25_AR2315_REGS_H */
---- /dev/null
-+++ b/arch/mips/ath25/ar5312_regs.h
-@@ -0,0 +1,224 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
-+ */
-+
-+#ifndef __ASM_MACH_ATH25_AR5312_REGS_H
-+#define __ASM_MACH_ATH25_AR5312_REGS_H
-+
-+/*
-+ * IRQs
-+ */
-+#define AR5312_IRQ_WLAN0	(MIPS_CPU_IRQ_BASE + 2)	/* C0_CAUSE: 0x0400 */
-+#define AR5312_IRQ_ENET0	(MIPS_CPU_IRQ_BASE + 3)	/* C0_CAUSE: 0x0800 */
-+#define AR5312_IRQ_ENET1	(MIPS_CPU_IRQ_BASE + 4)	/* C0_CAUSE: 0x1000 */
-+#define AR5312_IRQ_WLAN1	(MIPS_CPU_IRQ_BASE + 5)	/* C0_CAUSE: 0x2000 */
-+#define AR5312_IRQ_MISC		(MIPS_CPU_IRQ_BASE + 6)	/* C0_CAUSE: 0x4000 */
-+
-+/*
-+ * Miscellaneous interrupts, which share IP6.
-+ */
-+#define AR5312_MISC_IRQ_TIMER		0
-+#define AR5312_MISC_IRQ_AHB_PROC	1
-+#define AR5312_MISC_IRQ_AHB_DMA		2
-+#define AR5312_MISC_IRQ_GPIO		3
-+#define AR5312_MISC_IRQ_UART0		4
-+#define AR5312_MISC_IRQ_UART0_DMA	5
-+#define AR5312_MISC_IRQ_WATCHDOG	6
-+#define AR5312_MISC_IRQ_LOCAL		7
-+#define AR5312_MISC_IRQ_SPI		8
-+#define AR5312_MISC_IRQ_COUNT		9
-+
-+/*
-+ * Address Map
-+ *
-+ * The AR5312 supports 2 enet MACS, even though many reference boards only
-+ * actually use 1 of them (i.e. Only MAC 0 is actually connected to an enet
-+ * PHY or PHY switch. The AR2312 supports 1 enet MAC.
-+ */
-+#define AR5312_WLAN0_BASE		0x18000000
-+#define AR5312_ENET0_BASE		0x18100000
-+#define AR5312_ENET1_BASE		0x18200000
-+#define AR5312_SDRAMCTL_BASE		0x18300000
-+#define AR5312_SDRAMCTL_SIZE		0x00000010
-+#define AR5312_FLASHCTL_BASE		0x18400000
-+#define AR5312_FLASHCTL_SIZE		0x00000010
-+#define AR5312_WLAN1_BASE		0x18500000
-+#define AR5312_UART0_BASE		0x1c000000	/* UART MMR */
-+#define AR5312_GPIO_BASE		0x1c002000
-+#define AR5312_GPIO_SIZE		0x00000010
-+#define AR5312_RST_BASE			0x1c003000
-+#define AR5312_RST_SIZE			0x00000100
-+#define AR5312_FLASH_BASE		0x1e000000
-+#define AR5312_FLASH_SIZE		0x00800000
-+
-+/*
-+ * Need these defines to determine true number of ethernet MACs
-+ */
-+#define AR5312_AR5312_REV2	0x0052		/* AR5312 WMAC (AP31) */
-+#define AR5312_AR5312_REV7	0x0057		/* AR5312 WMAC (AP30-040) */
-+#define AR5312_AR2313_REV8	0x0058		/* AR2313 WMAC (AP43-030) */
-+
-+/* Reset/Timer Block Address Map */
-+#define AR5312_TIMER		0x0000 /* countdown timer */
-+#define AR5312_RELOAD		0x0004 /* timer reload value */
-+#define AR5312_WDT_CTRL		0x0008 /* watchdog cntrl */
-+#define AR5312_WDT_TIMER	0x000c /* watchdog timer */
-+#define AR5312_ISR		0x0010 /* Intr Status Reg */
-+#define AR5312_IMR		0x0014 /* Intr Mask Reg */
-+#define AR5312_RESET		0x0020
-+#define AR5312_CLOCKCTL1	0x0064
-+#define AR5312_SCRATCH		0x006c
-+#define AR5312_PROCADDR		0x0070
-+#define AR5312_PROC1		0x0074
-+#define AR5312_DMAADDR		0x0078
-+#define AR5312_DMA1		0x007c
-+#define AR5312_ENABLE		0x0080 /* interface enb */
-+#define AR5312_REV		0x0090 /* revision */
-+
-+/* AR5312_WDT_CTRL register bit field definitions */
-+#define AR5312_WDT_CTRL_IGNORE	0x00000000	/* ignore expiration */
-+#define AR5312_WDT_CTRL_NMI	0x00000001
-+#define AR5312_WDT_CTRL_RESET	0x00000002
-+
-+/* AR5312_ISR register bit field definitions */
-+#define AR5312_ISR_TIMER	0x00000001
-+#define AR5312_ISR_AHBPROC	0x00000002
-+#define AR5312_ISR_AHBDMA	0x00000004
-+#define AR5312_ISR_GPIO		0x00000008
-+#define AR5312_ISR_UART0	0x00000010
-+#define AR5312_ISR_UART0DMA	0x00000020
-+#define AR5312_ISR_WD		0x00000040
-+#define AR5312_ISR_LOCAL	0x00000080
-+
-+/* AR5312_RESET register bit field definitions */
-+#define AR5312_RESET_SYSTEM		0x00000001  /* cold reset full system */
-+#define AR5312_RESET_PROC		0x00000002  /* cold reset MIPS core */
-+#define AR5312_RESET_WLAN0		0x00000004  /* cold reset WLAN MAC/BB */
-+#define AR5312_RESET_EPHY0		0x00000008  /* cold reset ENET0 phy */
-+#define AR5312_RESET_EPHY1		0x00000010  /* cold reset ENET1 phy */
-+#define AR5312_RESET_ENET0		0x00000020  /* cold reset ENET0 MAC */
-+#define AR5312_RESET_ENET1		0x00000040  /* cold reset ENET1 MAC */
-+#define AR5312_RESET_UART0		0x00000100  /* cold reset UART0 */
-+#define AR5312_RESET_WLAN1		0x00000200  /* cold reset WLAN MAC/BB */
-+#define AR5312_RESET_APB		0x00000400  /* cold reset APB ar5312 */
-+#define AR5312_RESET_WARM_PROC		0x00001000  /* warm reset MIPS core */
-+#define AR5312_RESET_WARM_WLAN0_MAC	0x00002000  /* warm reset WLAN0 MAC */
-+#define AR5312_RESET_WARM_WLAN0_BB	0x00004000  /* warm reset WLAN0 BB */
-+#define AR5312_RESET_NMI		0x00010000  /* send an NMI to the CPU */
-+#define AR5312_RESET_WARM_WLAN1_MAC	0x00020000  /* warm reset WLAN1 MAC */
-+#define AR5312_RESET_WARM_WLAN1_BB	0x00040000  /* warm reset WLAN1 BB */
-+#define AR5312_RESET_LOCAL_BUS		0x00080000  /* reset local bus */
-+#define AR5312_RESET_WDOG		0x00100000  /* last reset was a wdt */
-+
-+#define AR5312_RESET_WMAC0_BITS		(AR5312_RESET_WLAN0 |\
-+					 AR5312_RESET_WARM_WLAN0_MAC |\
-+					 AR5312_RESET_WARM_WLAN0_BB)
-+
-+#define AR5312_RESET_WMAC1_BITS		(AR5312_RESET_WLAN1 |\
-+					 AR5312_RESET_WARM_WLAN1_MAC |\
-+					 AR5312_RESET_WARM_WLAN1_BB)
-+
-+/* AR5312_CLOCKCTL1 register bit field definitions */
-+#define AR5312_CLOCKCTL1_PREDIVIDE_MASK		0x00000030
-+#define AR5312_CLOCKCTL1_PREDIVIDE_SHIFT	4
-+#define AR5312_CLOCKCTL1_MULTIPLIER_MASK	0x00001f00
-+#define AR5312_CLOCKCTL1_MULTIPLIER_SHIFT	8
-+#define AR5312_CLOCKCTL1_DOUBLER_MASK		0x00010000
-+
-+/* Valid for AR5312 and AR2312 */
-+#define AR5312_CLOCKCTL1_PREDIVIDE_MASK		0x00000030
-+#define AR5312_CLOCKCTL1_PREDIVIDE_SHIFT	4
-+#define AR5312_CLOCKCTL1_MULTIPLIER_MASK	0x00001f00
-+#define AR5312_CLOCKCTL1_MULTIPLIER_SHIFT	8
-+#define AR5312_CLOCKCTL1_DOUBLER_MASK		0x00010000
-+
-+/* Valid for AR2313 */
-+#define AR2313_CLOCKCTL1_PREDIVIDE_MASK		0x00003000
-+#define AR2313_CLOCKCTL1_PREDIVIDE_SHIFT	12
-+#define AR2313_CLOCKCTL1_MULTIPLIER_MASK	0x001f0000
-+#define AR2313_CLOCKCTL1_MULTIPLIER_SHIFT	16
-+#define AR2313_CLOCKCTL1_DOUBLER_MASK		0x00000000
-+
-+/* AR5312_ENABLE register bit field definitions */
-+#define AR5312_ENABLE_WLAN0			0x00000001
-+#define AR5312_ENABLE_ENET0			0x00000002
-+#define AR5312_ENABLE_ENET1			0x00000004
-+#define AR5312_ENABLE_UART_AND_WLAN1_PIO	0x00000008/* UART & WLAN1 PIO */
-+#define AR5312_ENABLE_WLAN1_DMA			0x00000010/* WLAN1 DMAs */
-+#define AR5312_ENABLE_WLAN1		(AR5312_ENABLE_UART_AND_WLAN1_PIO |\
-+					 AR5312_ENABLE_WLAN1_DMA)
-+
-+/* AR5312_REV register bit field definitions */
-+#define AR5312_REV_WMAC_MAJ	0x0000f000
-+#define AR5312_REV_WMAC_MAJ_S	12
-+#define AR5312_REV_WMAC_MIN	0x00000f00
-+#define AR5312_REV_WMAC_MIN_S	8
-+#define AR5312_REV_MAJ		0x000000f0
-+#define AR5312_REV_MAJ_S	4
-+#define AR5312_REV_MIN		0x0000000f
-+#define AR5312_REV_MIN_S	0
-+#define AR5312_REV_CHIP		(AR5312_REV_MAJ|AR5312_REV_MIN)
-+
-+/* Major revision numbers, bits 7..4 of Revision ID register */
-+#define AR5312_REV_MAJ_AR5312		0x4
-+#define AR5312_REV_MAJ_AR2313		0x5
-+
-+/* Minor revision numbers, bits 3..0 of Revision ID register */
-+#define AR5312_REV_MIN_DUAL		0x0	/* Dual WLAN version */
-+#define AR5312_REV_MIN_SINGLE		0x1	/* Single WLAN version */
-+
-+/*
-+ * ARM Flash Controller -- 3 flash banks with either x8 or x16 devices
-+ */
-+#define AR5312_FLASHCTL0	0x0000
-+#define AR5312_FLASHCTL1	0x0004
-+#define AR5312_FLASHCTL2	0x0008
-+
-+/* AR5312_FLASHCTL register bit field definitions */
-+#define AR5312_FLASHCTL_IDCY	0x0000000f	/* Idle cycle turnaround time */
-+#define AR5312_FLASHCTL_IDCY_S	0
-+#define AR5312_FLASHCTL_WST1	0x000003e0	/* Wait state 1 */
-+#define AR5312_FLASHCTL_WST1_S	5
-+#define AR5312_FLASHCTL_RBLE	0x00000400	/* Read byte lane enable */
-+#define AR5312_FLASHCTL_WST2	0x0000f800	/* Wait state 2 */
-+#define AR5312_FLASHCTL_WST2_S	11
-+#define AR5312_FLASHCTL_AC	0x00070000	/* Flash addr check (added) */
-+#define AR5312_FLASHCTL_AC_S	16
-+#define AR5312_FLASHCTL_AC_128K	0x00000000
-+#define AR5312_FLASHCTL_AC_256K	0x00010000
-+#define AR5312_FLASHCTL_AC_512K	0x00020000
-+#define AR5312_FLASHCTL_AC_1M	0x00030000
-+#define AR5312_FLASHCTL_AC_2M	0x00040000
-+#define AR5312_FLASHCTL_AC_4M	0x00050000
-+#define AR5312_FLASHCTL_AC_8M	0x00060000
-+#define AR5312_FLASHCTL_AC_RES	0x00070000	/* 16MB is not supported */
-+#define AR5312_FLASHCTL_E	0x00080000	/* Flash bank enable (added) */
-+#define AR5312_FLASHCTL_BUSERR	0x01000000	/* Bus transfer error flag */
-+#define AR5312_FLASHCTL_WPERR	0x02000000	/* Write protect error flag */
-+#define AR5312_FLASHCTL_WP	0x04000000	/* Write protect */
-+#define AR5312_FLASHCTL_BM	0x08000000	/* Burst mode */
-+#define AR5312_FLASHCTL_MW	0x30000000	/* Mem width */
-+#define AR5312_FLASHCTL_MW8	0x00000000	/* Mem width x8 */
-+#define AR5312_FLASHCTL_MW16	0x10000000	/* Mem width x16 */
-+#define AR5312_FLASHCTL_MW32	0x20000000	/* Mem width x32 (not supp) */
-+#define AR5312_FLASHCTL_ATNR	0x00000000	/* Access == no retry */
-+#define AR5312_FLASHCTL_ATR	0x80000000	/* Access == retry every */
-+#define AR5312_FLASHCTL_ATR4	0xc0000000	/* Access == retry every 4 */
-+
-+/*
-+ * ARM SDRAM Controller -- just enough to determine memory size
-+ */
-+#define AR5312_MEM_CFG1		0x0004
-+
-+#define AR5312_MEM_CFG1_AC0_M	0x00000700	/* bank 0: SDRAM addr check */
-+#define AR5312_MEM_CFG1_AC0_S	8
-+#define AR5312_MEM_CFG1_AC1_M	0x00007000	/* bank 1: SDRAM addr check */
-+#define AR5312_MEM_CFG1_AC1_S	12
-+
-+#endif	/* __ASM_MACH_ATH25_AR5312_REGS_H */
---- /dev/null
-+++ b/arch/mips/ath25/ar5312.c
-@@ -0,0 +1,393 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
-+ * Copyright (C) 2006 FON Technology, SL.
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
-+ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
-+ */
-+
-+/*
-+ * Platform devices for Atheros AR5312 SoCs
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/bitops.h>
-+#include <linux/irqdomain.h>
-+#include <linux/interrupt.h>
-+#include <linux/platform_device.h>
-+#include <linux/mtd/physmap.h>
-+#include <linux/reboot.h>
-+#include <asm/bootinfo.h>
-+#include <asm/reboot.h>
-+#include <asm/time.h>
-+
-+#include <ath25_platform.h>
-+
-+#include "devices.h"
-+#include "ar5312.h"
-+#include "ar5312_regs.h"
-+
-+static void __iomem *ar5312_rst_base;
-+static struct irq_domain *ar5312_misc_irq_domain;
-+
-+static inline u32 ar5312_rst_reg_read(u32 reg)
-+{
-+	return __raw_readl(ar5312_rst_base + reg);
-+}
-+
-+static inline void ar5312_rst_reg_write(u32 reg, u32 val)
-+{
-+	__raw_writel(val, ar5312_rst_base + reg);
-+}
-+
-+static inline void ar5312_rst_reg_mask(u32 reg, u32 mask, u32 val)
-+{
-+	u32 ret = ar5312_rst_reg_read(reg);
-+
-+	ret &= ~mask;
-+	ret |= val;
-+	ar5312_rst_reg_write(reg, ret);
-+}
-+
-+static irqreturn_t ar5312_ahb_err_handler(int cpl, void *dev_id)
-+{
-+	u32 proc1 = ar5312_rst_reg_read(AR5312_PROC1);
-+	u32 proc_addr = ar5312_rst_reg_read(AR5312_PROCADDR); /* clears error */
-+	u32 dma1 = ar5312_rst_reg_read(AR5312_DMA1);
-+	u32 dma_addr = ar5312_rst_reg_read(AR5312_DMAADDR);   /* clears error */
-+
-+	pr_emerg("AHB interrupt: PROCADDR=0x%8.8x PROC1=0x%8.8x DMAADDR=0x%8.8x DMA1=0x%8.8x\n",
-+		 proc_addr, proc1, dma_addr, dma1);
-+
-+	machine_restart("AHB error"); /* Catastrophic failure */
-+	return IRQ_HANDLED;
-+}
-+
-+static struct irqaction ar5312_ahb_err_interrupt  = {
-+	.handler = ar5312_ahb_err_handler,
-+	.name    = "ar5312-ahb-error",
-+};
-+
-+static void ar5312_misc_irq_handler(unsigned irq, struct irq_desc *desc)
-+{
-+	u32 pending = ar5312_rst_reg_read(AR5312_ISR) &
-+		      ar5312_rst_reg_read(AR5312_IMR);
-+	unsigned nr, misc_irq = 0;
-+
-+	if (pending) {
-+		struct irq_domain *domain = irq_get_handler_data(irq);
-+
-+		nr = __ffs(pending);
-+		misc_irq = irq_find_mapping(domain, nr);
-+	}
-+
-+	if (misc_irq) {
-+		generic_handle_irq(misc_irq);
-+		if (nr == AR5312_MISC_IRQ_TIMER)
-+			ar5312_rst_reg_read(AR5312_TIMER);
-+	} else {
-+		spurious_interrupt();
-+	}
-+}
-+
-+/* Enable the specified AR5312_MISC_IRQ interrupt */
-+static void ar5312_misc_irq_unmask(struct irq_data *d)
-+{
-+	ar5312_rst_reg_mask(AR5312_IMR, 0, BIT(d->hwirq));
-+}
-+
-+/* Disable the specified AR5312_MISC_IRQ interrupt */
-+static void ar5312_misc_irq_mask(struct irq_data *d)
-+{
-+	ar5312_rst_reg_mask(AR5312_IMR, BIT(d->hwirq), 0);
-+	ar5312_rst_reg_read(AR5312_IMR); /* flush write buffer */
-+}
-+
-+static struct irq_chip ar5312_misc_irq_chip = {
-+	.name		= "ar5312-misc",
-+	.irq_unmask	= ar5312_misc_irq_unmask,
-+	.irq_mask	= ar5312_misc_irq_mask,
-+};
-+
-+static int ar5312_misc_irq_map(struct irq_domain *d, unsigned irq,
-+			       irq_hw_number_t hw)
-+{
-+	irq_set_chip_and_handler(irq, &ar5312_misc_irq_chip, handle_level_irq);
-+	return 0;
-+}
-+
-+static struct irq_domain_ops ar5312_misc_irq_domain_ops = {
-+	.map = ar5312_misc_irq_map,
-+};
-+
-+static void ar5312_irq_dispatch(void)
-+{
-+	u32 pending = read_c0_status() & read_c0_cause();
-+
-+	if (pending & CAUSEF_IP2)
-+		do_IRQ(AR5312_IRQ_WLAN0);
-+	else if (pending & CAUSEF_IP5)
-+		do_IRQ(AR5312_IRQ_WLAN1);
-+	else if (pending & CAUSEF_IP6)
-+		do_IRQ(AR5312_IRQ_MISC);
-+	else if (pending & CAUSEF_IP7)
-+		do_IRQ(ATH25_IRQ_CPU_CLOCK);
-+	else
-+		spurious_interrupt();
-+}
-+
-+void __init ar5312_arch_init_irq(void)
-+{
-+	struct irq_domain *domain;
-+	unsigned irq;
-+
-+	ath25_irq_dispatch = ar5312_irq_dispatch;
-+
-+	domain = irq_domain_add_linear(NULL, AR5312_MISC_IRQ_COUNT,
-+				       &ar5312_misc_irq_domain_ops, NULL);
-+	if (!domain)
-+		panic("Failed to add IRQ domain");
-+
-+	irq = irq_create_mapping(domain, AR5312_MISC_IRQ_AHB_PROC);
-+	setup_irq(irq, &ar5312_ahb_err_interrupt);
-+
-+	irq_set_chained_handler(AR5312_IRQ_MISC, ar5312_misc_irq_handler);
-+	irq_set_handler_data(AR5312_IRQ_MISC, domain);
-+
-+	ar5312_misc_irq_domain = domain;
-+}
-+
-+static struct physmap_flash_data ar5312_flash_data = {
-+	.width = 2,
-+};
-+
-+static struct resource ar5312_flash_resource = {
-+	.start = AR5312_FLASH_BASE,
-+	.end = AR5312_FLASH_BASE + AR5312_FLASH_SIZE - 1,
-+	.flags = IORESOURCE_MEM,
-+};
-+
-+static struct platform_device ar5312_physmap_flash = {
-+	.name = "physmap-flash",
-+	.id = 0,
-+	.dev.platform_data = &ar5312_flash_data,
-+	.resource = &ar5312_flash_resource,
-+	.num_resources = 1,
-+};
-+
-+static void __init ar5312_flash_init(void)
-+{
-+	void __iomem *flashctl_base;
-+	u32 ctl;
-+
-+	flashctl_base = ioremap_nocache(AR5312_FLASHCTL_BASE,
-+					AR5312_FLASHCTL_SIZE);
-+
-+	ctl = __raw_readl(flashctl_base + AR5312_FLASHCTL0);
-+	ctl &= AR5312_FLASHCTL_MW;
-+
-+	/* fixup flash width */
-+	switch (ctl) {
-+	case AR5312_FLASHCTL_MW16:
-+		ar5312_flash_data.width = 2;
-+		break;
-+	case AR5312_FLASHCTL_MW8:
-+	default:
-+		ar5312_flash_data.width = 1;
-+		break;
-+	}
-+
-+	/*
-+	 * Configure flash bank 0.
-+	 * Assume 8M window size. Flash will be aliased if it's smaller
-+	 */
-+	ctl |= AR5312_FLASHCTL_E | AR5312_FLASHCTL_AC_8M | AR5312_FLASHCTL_RBLE;
-+	ctl |= 0x01 << AR5312_FLASHCTL_IDCY_S;
-+	ctl |= 0x07 << AR5312_FLASHCTL_WST1_S;
-+	ctl |= 0x07 << AR5312_FLASHCTL_WST2_S;
-+	__raw_writel(ctl, flashctl_base + AR5312_FLASHCTL0);
-+
-+	/* Disable other flash banks */
-+	ctl = __raw_readl(flashctl_base + AR5312_FLASHCTL1);
-+	ctl &= ~(AR5312_FLASHCTL_E | AR5312_FLASHCTL_AC);
-+	__raw_writel(ctl, flashctl_base + AR5312_FLASHCTL1);
-+	ctl = __raw_readl(flashctl_base + AR5312_FLASHCTL2);
-+	ctl &= ~(AR5312_FLASHCTL_E | AR5312_FLASHCTL_AC);
-+	__raw_writel(ctl, flashctl_base + AR5312_FLASHCTL2);
-+
-+	iounmap(flashctl_base);
-+}
-+
-+void __init ar5312_init_devices(void)
-+{
-+	struct ath25_boarddata *config;
-+
-+	ar5312_flash_init();
-+
-+	/* Locate board/radio config data */
-+	ath25_find_config(AR5312_FLASH_BASE, AR5312_FLASH_SIZE);
-+	config = ath25_board.config;
-+
-+	/* AR2313 has CPU minor rev. 10 */
-+	if ((current_cpu_data.processor_id & 0xff) == 0x0a)
-+		ath25_soc = ATH25_SOC_AR2313;
-+
-+	/* AR2312 shares the same Silicon ID as AR5312 */
-+	else if (config->flags & BD_ISCASPER)
-+		ath25_soc = ATH25_SOC_AR2312;
-+
-+	/* Everything else is probably AR5312 or compatible */
-+	else
-+		ath25_soc = ATH25_SOC_AR5312;
-+
-+	platform_device_register(&ar5312_physmap_flash);
-+
-+	switch (ath25_soc) {
-+	case ATH25_SOC_AR5312:
-+		if (!ath25_board.radio)
-+			return;
-+
-+		if (!(config->flags & BD_WLAN0))
-+			break;
-+
-+		ath25_add_wmac(0, AR5312_WLAN0_BASE, AR5312_IRQ_WLAN0);
-+		break;
-+	case ATH25_SOC_AR2312:
-+	case ATH25_SOC_AR2313:
-+		if (!ath25_board.radio)
-+			return;
-+		break;
-+	default:
-+		break;
-+	}
-+
-+	if (config->flags & BD_WLAN1)
-+		ath25_add_wmac(1, AR5312_WLAN1_BASE, AR5312_IRQ_WLAN1);
-+}
-+
-+static void ar5312_restart(char *command)
-+{
-+	/* reset the system */
-+	local_irq_disable();
-+	while (1)
-+		ar5312_rst_reg_write(AR5312_RESET, AR5312_RESET_SYSTEM);
-+}
-+
-+/*
-+ * This table is indexed by bits 5..4 of the CLOCKCTL1 register
-+ * to determine the predevisor value.
-+ */
-+static unsigned clockctl1_predivide_table[4] __initdata = { 1, 2, 4, 5 };
-+
-+static unsigned __init ar5312_cpu_frequency(void)
-+{
-+	u32 scratch, devid, clock_ctl1;
-+	u32 predivide_mask, multiplier_mask, doubler_mask;
-+	unsigned predivide_shift, multiplier_shift;
-+	unsigned predivide_select, predivisor, multiplier;
-+
-+	/* Trust the bootrom's idea of cpu frequency. */
-+	scratch = ar5312_rst_reg_read(AR5312_SCRATCH);
-+	if (scratch)
-+		return scratch;
-+
-+	devid = ar5312_rst_reg_read(AR5312_REV);
-+	devid = (devid & AR5312_REV_MAJ) >> AR5312_REV_MAJ_S;
-+	if (devid == AR5312_REV_MAJ_AR2313) {
-+		predivide_mask = AR2313_CLOCKCTL1_PREDIVIDE_MASK;
-+		predivide_shift = AR2313_CLOCKCTL1_PREDIVIDE_SHIFT;
-+		multiplier_mask = AR2313_CLOCKCTL1_MULTIPLIER_MASK;
-+		multiplier_shift = AR2313_CLOCKCTL1_MULTIPLIER_SHIFT;
-+		doubler_mask = AR2313_CLOCKCTL1_DOUBLER_MASK;
-+	} else { /* AR5312 and AR2312 */
-+		predivide_mask = AR5312_CLOCKCTL1_PREDIVIDE_MASK;
-+		predivide_shift = AR5312_CLOCKCTL1_PREDIVIDE_SHIFT;
-+		multiplier_mask = AR5312_CLOCKCTL1_MULTIPLIER_MASK;
-+		multiplier_shift = AR5312_CLOCKCTL1_MULTIPLIER_SHIFT;
-+		doubler_mask = AR5312_CLOCKCTL1_DOUBLER_MASK;
-+	}
-+
-+	/*
-+	 * Clocking is derived from a fixed 40MHz input clock.
-+	 *
-+	 *  cpu_freq = input_clock * MULT (where MULT is PLL multiplier)
-+	 *  sys_freq = cpu_freq / 4	  (used for APB clock, serial,
-+	 *				   flash, Timer, Watchdog Timer)
-+	 *
-+	 *  cnt_freq = cpu_freq / 2	  (use for CPU count/compare)
-+	 *
-+	 * So, for example, with a PLL multiplier of 5, we have
-+	 *
-+	 *  cpu_freq = 200MHz
-+	 *  sys_freq = 50MHz
-+	 *  cnt_freq = 100MHz
-+	 *
-+	 * We compute the CPU frequency, based on PLL settings.
-+	 */
-+
-+	clock_ctl1 = ar5312_rst_reg_read(AR5312_CLOCKCTL1);
-+	predivide_select = (clock_ctl1 & predivide_mask) >> predivide_shift;
-+	predivisor = clockctl1_predivide_table[predivide_select];
-+	multiplier = (clock_ctl1 & multiplier_mask) >> multiplier_shift;
-+
-+	if (clock_ctl1 & doubler_mask)
-+		multiplier <<= 1;
-+
-+	return (40000000 / predivisor) * multiplier;
-+}
-+
-+static inline unsigned ar5312_sys_frequency(void)
-+{
-+	return ar5312_cpu_frequency() / 4;
-+}
-+
-+void __init ar5312_plat_time_init(void)
-+{
-+	mips_hpt_frequency = ar5312_cpu_frequency() / 2;
-+}
-+
-+void __init ar5312_plat_mem_setup(void)
-+{
-+	void __iomem *sdram_base;
-+	u32 memsize, memcfg, bank0_ac, bank1_ac;
-+	u32 devid;
-+
-+	/* Detect memory size */
-+	sdram_base = ioremap_nocache(AR5312_SDRAMCTL_BASE,
-+				     AR5312_SDRAMCTL_SIZE);
-+	memcfg = __raw_readl(sdram_base + AR5312_MEM_CFG1);
-+	bank0_ac = ATH25_REG_MS(memcfg, AR5312_MEM_CFG1_AC0);
-+	bank1_ac = ATH25_REG_MS(memcfg, AR5312_MEM_CFG1_AC1);
-+	memsize = (bank0_ac ? (1 << (bank0_ac + 1)) : 0) +
-+		  (bank1_ac ? (1 << (bank1_ac + 1)) : 0);
-+	memsize <<= 20;
-+	add_memory_region(0, memsize, BOOT_MEM_RAM);
-+	iounmap(sdram_base);
-+
-+	ar5312_rst_base = ioremap_nocache(AR5312_RST_BASE, AR5312_RST_SIZE);
-+
-+	devid = ar5312_rst_reg_read(AR5312_REV);
-+	devid >>= AR5312_REV_WMAC_MIN_S;
-+	devid &= AR5312_REV_CHIP;
-+	ath25_board.devid = (u16)devid;
-+
-+	/* Clear any lingering AHB errors */
-+	ar5312_rst_reg_read(AR5312_PROCADDR);
-+	ar5312_rst_reg_read(AR5312_DMAADDR);
-+	ar5312_rst_reg_write(AR5312_WDT_CTRL, AR5312_WDT_CTRL_IGNORE);
-+
-+	_machine_restart = ar5312_restart;
-+}
-+
-+void __init ar5312_arch_init(void)
-+{
-+	unsigned irq = irq_create_mapping(ar5312_misc_irq_domain,
-+					  AR5312_MISC_IRQ_UART0);
-+
-+	ath25_serial_setup(AR5312_UART0_BASE, irq, ar5312_sys_frequency());
-+}
---- /dev/null
-+++ b/arch/mips/ath25/ar2315.c
-@@ -0,0 +1,308 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
-+ * Copyright (C) 2006 FON Technology, SL.
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
-+ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
-+ */
-+
-+/*
-+ * Platform devices for Atheros AR2315 SoCs
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/bitops.h>
-+#include <linux/irqdomain.h>
-+#include <linux/interrupt.h>
-+#include <linux/platform_device.h>
-+#include <linux/reboot.h>
-+#include <asm/bootinfo.h>
-+#include <asm/reboot.h>
-+#include <asm/time.h>
-+
-+#include <ath25_platform.h>
-+
-+#include "devices.h"
-+#include "ar2315.h"
-+#include "ar2315_regs.h"
-+
-+static void __iomem *ar2315_rst_base;
-+static struct irq_domain *ar2315_misc_irq_domain;
-+
-+static inline u32 ar2315_rst_reg_read(u32 reg)
-+{
-+	return __raw_readl(ar2315_rst_base + reg);
-+}
-+
-+static inline void ar2315_rst_reg_write(u32 reg, u32 val)
-+{
-+	__raw_writel(val, ar2315_rst_base + reg);
-+}
-+
-+static inline void ar2315_rst_reg_mask(u32 reg, u32 mask, u32 val)
-+{
-+	u32 ret = ar2315_rst_reg_read(reg);
-+
-+	ret &= ~mask;
-+	ret |= val;
-+	ar2315_rst_reg_write(reg, ret);
-+}
-+
-+static irqreturn_t ar2315_ahb_err_handler(int cpl, void *dev_id)
-+{
-+	ar2315_rst_reg_write(AR2315_AHB_ERR0, AR2315_AHB_ERROR_DET);
-+	ar2315_rst_reg_read(AR2315_AHB_ERR1);
-+
-+	pr_emerg("AHB fatal error\n");
-+	machine_restart("AHB error"); /* Catastrophic failure */
-+
-+	return IRQ_HANDLED;
-+}
-+
-+static struct irqaction ar2315_ahb_err_interrupt  = {
-+	.handler	= ar2315_ahb_err_handler,
-+	.name		= "ar2315-ahb-error",
-+};
-+
-+static void ar2315_misc_irq_handler(unsigned irq, struct irq_desc *desc)
-+{
-+	u32 pending = ar2315_rst_reg_read(AR2315_ISR) &
-+		      ar2315_rst_reg_read(AR2315_IMR);
-+	unsigned nr, misc_irq = 0;
-+
-+	if (pending) {
-+		struct irq_domain *domain = irq_get_handler_data(irq);
-+
-+		nr = __ffs(pending);
-+		misc_irq = irq_find_mapping(domain, nr);
-+	}
-+
-+	if (misc_irq) {
-+		if (nr == AR2315_MISC_IRQ_GPIO)
-+			ar2315_rst_reg_write(AR2315_ISR, AR2315_ISR_GPIO);
-+		else if (nr == AR2315_MISC_IRQ_WATCHDOG)
-+			ar2315_rst_reg_write(AR2315_ISR, AR2315_ISR_WD);
-+		generic_handle_irq(misc_irq);
-+	} else {
-+		spurious_interrupt();
-+	}
-+}
-+
-+static void ar2315_misc_irq_unmask(struct irq_data *d)
-+{
-+	ar2315_rst_reg_mask(AR2315_IMR, 0, BIT(d->hwirq));
-+}
-+
-+static void ar2315_misc_irq_mask(struct irq_data *d)
-+{
-+	ar2315_rst_reg_mask(AR2315_IMR, BIT(d->hwirq), 0);
-+}
-+
-+static struct irq_chip ar2315_misc_irq_chip = {
-+	.name		= "ar2315-misc",
-+	.irq_unmask	= ar2315_misc_irq_unmask,
-+	.irq_mask	= ar2315_misc_irq_mask,
-+};
-+
-+static int ar2315_misc_irq_map(struct irq_domain *d, unsigned irq,
-+			       irq_hw_number_t hw)
-+{
-+	irq_set_chip_and_handler(irq, &ar2315_misc_irq_chip, handle_level_irq);
-+	return 0;
-+}
-+
-+static struct irq_domain_ops ar2315_misc_irq_domain_ops = {
-+	.map = ar2315_misc_irq_map,
-+};
-+
-+/*
-+ * Called when an interrupt is received, this function
-+ * determines exactly which interrupt it was, and it
-+ * invokes the appropriate handler.
-+ *
-+ * Implicitly, we also define interrupt priority by
-+ * choosing which to dispatch first.
-+ */
-+static void ar2315_irq_dispatch(void)
-+{
-+	u32 pending = read_c0_status() & read_c0_cause();
-+
-+	if (pending & CAUSEF_IP3)
-+		do_IRQ(AR2315_IRQ_WLAN0);
-+	else if (pending & CAUSEF_IP2)
-+		do_IRQ(AR2315_IRQ_MISC);
-+	else if (pending & CAUSEF_IP7)
-+		do_IRQ(ATH25_IRQ_CPU_CLOCK);
-+	else
-+		spurious_interrupt();
-+}
-+
-+void __init ar2315_arch_init_irq(void)
-+{
-+	struct irq_domain *domain;
-+	unsigned irq;
-+
-+	ath25_irq_dispatch = ar2315_irq_dispatch;
-+
-+	domain = irq_domain_add_linear(NULL, AR2315_MISC_IRQ_COUNT,
-+				       &ar2315_misc_irq_domain_ops, NULL);
-+	if (!domain)
-+		panic("Failed to add IRQ domain");
-+
-+	irq = irq_create_mapping(domain, AR2315_MISC_IRQ_AHB);
-+	setup_irq(irq, &ar2315_ahb_err_interrupt);
-+
-+	irq_set_chained_handler(AR2315_IRQ_MISC, ar2315_misc_irq_handler);
-+	irq_set_handler_data(AR2315_IRQ_MISC, domain);
-+
-+	ar2315_misc_irq_domain = domain;
-+}
-+
-+void __init ar2315_init_devices(void)
-+{
-+	/* Find board configuration */
-+	ath25_find_config(AR2315_SPI_READ_BASE, AR2315_SPI_READ_SIZE);
-+
-+	ath25_add_wmac(0, AR2315_WLAN0_BASE, AR2315_IRQ_WLAN0);
-+}
-+
-+static void ar2315_restart(char *command)
-+{
-+	void (*mips_reset_vec)(void) = (void *)0xbfc00000;
-+
-+	local_irq_disable();
-+
-+	/* try reset the system via reset control */
-+	ar2315_rst_reg_write(AR2315_COLD_RESET, AR2317_RESET_SYSTEM);
-+
-+	/* Cold reset does not work on the AR2315/6, use the GPIO reset bits
-+	 * a workaround. Give it some time to attempt a gpio based hardware
-+	 * reset (atheros reference design workaround) */
-+
-+	/* TODO: implement the GPIO reset workaround */
-+
-+	/* Some boards (e.g. Senao EOC-2610) don't implement the reset logic
-+	 * workaround. Attempt to jump to the mips reset location -
-+	 * the boot loader itself might be able to recover the system */
-+	mips_reset_vec();
-+}
-+
-+/*
-+ * This table is indexed by bits 5..4 of the CLOCKCTL1 register
-+ * to determine the predevisor value.
-+ */
-+static int clockctl1_predivide_table[4] __initdata = { 1, 2, 4, 5 };
-+static int pllc_divide_table[5] __initdata = { 2, 3, 4, 6, 3 };
-+
-+static unsigned __init ar2315_sys_clk(u32 clock_ctl)
-+{
-+	unsigned int pllc_ctrl, cpu_div;
-+	unsigned int pllc_out, refdiv, fdiv, divby2;
-+	unsigned int clk_div;
-+
-+	pllc_ctrl = ar2315_rst_reg_read(AR2315_PLLC_CTL);
-+	refdiv = ATH25_REG_MS(pllc_ctrl, AR2315_PLLC_REF_DIV);
-+	refdiv = clockctl1_predivide_table[refdiv];
-+	fdiv = ATH25_REG_MS(pllc_ctrl, AR2315_PLLC_FDBACK_DIV);
-+	divby2 = ATH25_REG_MS(pllc_ctrl, AR2315_PLLC_ADD_FDBACK_DIV) + 1;
-+	pllc_out = (40000000 / refdiv) * (2 * divby2) * fdiv;
-+
-+	/* clkm input selected */
-+	switch (clock_ctl & AR2315_CPUCLK_CLK_SEL_M) {
-+	case 0:
-+	case 1:
-+		clk_div = ATH25_REG_MS(pllc_ctrl, AR2315_PLLC_CLKM_DIV);
-+		clk_div = pllc_divide_table[clk_div];
-+		break;
-+	case 2:
-+		clk_div = ATH25_REG_MS(pllc_ctrl, AR2315_PLLC_CLKC_DIV);
-+		clk_div = pllc_divide_table[clk_div];
-+		break;
-+	default:
-+		pllc_out = 40000000;
-+		clk_div = 1;
-+		break;
-+	}
-+
-+	cpu_div = ATH25_REG_MS(clock_ctl, AR2315_CPUCLK_CLK_DIV);
-+	cpu_div = cpu_div * 2 ?: 1;
-+
-+	return pllc_out / (clk_div * cpu_div);
-+}
-+
-+static inline unsigned ar2315_cpu_frequency(void)
-+{
-+	return ar2315_sys_clk(ar2315_rst_reg_read(AR2315_CPUCLK));
-+}
-+
-+static inline unsigned ar2315_apb_frequency(void)
-+{
-+	return ar2315_sys_clk(ar2315_rst_reg_read(AR2315_AMBACLK));
-+}
-+
-+void __init ar2315_plat_time_init(void)
-+{
-+	mips_hpt_frequency = ar2315_cpu_frequency() / 2;
-+}
-+
-+void __init ar2315_plat_mem_setup(void)
-+{
-+	void __iomem *sdram_base;
-+	u32 memsize, memcfg;
-+	u32 devid;
-+	u32 config;
-+
-+	/* Detect memory size */
-+	sdram_base = ioremap_nocache(AR2315_SDRAMCTL_BASE,
-+				     AR2315_SDRAMCTL_SIZE);
-+	memcfg = __raw_readl(sdram_base + AR2315_MEM_CFG);
-+	memsize   = 1 + ATH25_REG_MS(memcfg, AR2315_MEM_CFG_DATA_WIDTH);
-+	memsize <<= 1 + ATH25_REG_MS(memcfg, AR2315_MEM_CFG_COL_WIDTH);
-+	memsize <<= 1 + ATH25_REG_MS(memcfg, AR2315_MEM_CFG_ROW_WIDTH);
-+	memsize <<= 3;
-+	add_memory_region(0, memsize, BOOT_MEM_RAM);
-+	iounmap(sdram_base);
-+
-+	ar2315_rst_base = ioremap_nocache(AR2315_RST_BASE, AR2315_RST_SIZE);
-+
-+	/* Detect the hardware based on the device ID */
-+	devid = ar2315_rst_reg_read(AR2315_SREV) & AR2315_REV_CHIP;
-+	switch (devid) {
-+	case 0x91:	/* Need to check */
-+		ath25_soc = ATH25_SOC_AR2318;
-+		break;
-+	case 0x90:
-+		ath25_soc = ATH25_SOC_AR2317;
-+		break;
-+	case 0x87:
-+		ath25_soc = ATH25_SOC_AR2316;
-+		break;
-+	case 0x86:
-+	default:
-+		ath25_soc = ATH25_SOC_AR2315;
-+		break;
-+	}
-+	ath25_board.devid = devid;
-+
-+	/* Clear any lingering AHB errors */
-+	config = read_c0_config();
-+	write_c0_config(config & ~0x3);
-+	ar2315_rst_reg_write(AR2315_AHB_ERR0, AR2315_AHB_ERROR_DET);
-+	ar2315_rst_reg_read(AR2315_AHB_ERR1);
-+	ar2315_rst_reg_write(AR2315_WDT_CTRL, AR2315_WDT_CTRL_IGNORE);
-+
-+	_machine_restart = ar2315_restart;
-+}
-+
-+void __init ar2315_arch_init(void)
-+{
-+	unsigned irq = irq_create_mapping(ar2315_misc_irq_domain,
-+					  AR2315_MISC_IRQ_UART0);
-+
-+	ath25_serial_setup(AR2315_UART0_BASE, irq, ar2315_apb_frequency());
-+}
---- /dev/null
-+++ b/arch/mips/ath25/ar2315.h
-@@ -0,0 +1,22 @@
-+#ifndef __AR2315_H
-+#define __AR2315_H
-+
-+#ifdef CONFIG_SOC_AR2315
-+
-+void ar2315_arch_init_irq(void);
-+void ar2315_init_devices(void);
-+void ar2315_plat_time_init(void);
-+void ar2315_plat_mem_setup(void);
-+void ar2315_arch_init(void);
-+
-+#else
-+
-+static inline void ar2315_arch_init_irq(void) {}
-+static inline void ar2315_init_devices(void) {}
-+static inline void ar2315_plat_time_init(void) {}
-+static inline void ar2315_plat_mem_setup(void) {}
-+static inline void ar2315_arch_init(void) {}
-+
-+#endif
-+
-+#endif	/* __AR2315_H */
---- /dev/null
-+++ b/arch/mips/ath25/ar5312.h
-@@ -0,0 +1,22 @@
-+#ifndef __AR5312_H
-+#define __AR5312_H
-+
-+#ifdef CONFIG_SOC_AR5312
-+
-+void ar5312_arch_init_irq(void);
-+void ar5312_init_devices(void);
-+void ar5312_plat_time_init(void);
-+void ar5312_plat_mem_setup(void);
-+void ar5312_arch_init(void);
-+
-+#else
-+
-+static inline void ar5312_arch_init_irq(void) {}
-+static inline void ar5312_init_devices(void) {}
-+static inline void ar5312_plat_time_init(void) {}
-+static inline void ar5312_plat_mem_setup(void) {}
-+static inline void ar5312_arch_init(void) {}
-+
-+#endif
-+
-+#endif	/* __AR5312_H */
---- /dev/null
-+++ b/arch/mips/ath25/devices.h
-@@ -0,0 +1,43 @@
-+#ifndef __ATH25_DEVICES_H
-+#define __ATH25_DEVICES_H
-+
-+#include <linux/cpu.h>
-+
-+#define ATH25_REG_MS(_val, _field)	(((_val) & _field##_M) >> _field##_S)
-+
-+#define ATH25_IRQ_CPU_CLOCK	(MIPS_CPU_IRQ_BASE + 7)	/* C0_CAUSE: 0x8000 */
-+
-+enum ath25_soc_type {
-+	/* handled by ar5312.c */
-+	ATH25_SOC_AR2312,
-+	ATH25_SOC_AR2313,
-+	ATH25_SOC_AR5312,
-+
-+	/* handled by ar2315.c */
-+	ATH25_SOC_AR2315,
-+	ATH25_SOC_AR2316,
-+	ATH25_SOC_AR2317,
-+	ATH25_SOC_AR2318,
-+
-+	ATH25_SOC_UNKNOWN
-+};
-+
-+extern enum ath25_soc_type ath25_soc;
-+extern struct ar231x_board_config ath25_board;
-+extern void (*ath25_irq_dispatch)(void);
-+
-+int ath25_find_config(phys_addr_t offset, unsigned long size);
-+void ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk);
-+int ath25_add_wmac(int nr, u32 base, int irq);
-+
-+static inline bool is_ar2315(void)
-+{
-+	return (current_cpu_data.cputype == CPU_4KEC);
-+}
-+
-+static inline bool is_ar5312(void)
-+{
-+	return !is_ar2315();
-+}
-+
-+#endif
---- /dev/null
-+++ b/arch/mips/ath25/devices.c
-@@ -0,0 +1,125 @@
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/serial_8250.h>
-+#include <linux/platform_device.h>
-+#include <asm/bootinfo.h>
-+
-+#include <ath25_platform.h>
-+#include "devices.h"
-+#include "ar5312.h"
-+#include "ar2315.h"
-+
-+struct ar231x_board_config ath25_board;
-+enum ath25_soc_type ath25_soc = ATH25_SOC_UNKNOWN;
-+
-+static struct resource ath25_wmac0_res[] = {
-+	{
-+		.name = "wmac0_membase",
-+		.flags = IORESOURCE_MEM,
-+	},
-+	{
-+		.name = "wmac0_irq",
-+		.flags = IORESOURCE_IRQ,
-+	}
-+};
-+
-+static struct resource ath25_wmac1_res[] = {
-+	{
-+		.name = "wmac1_membase",
-+		.flags = IORESOURCE_MEM,
-+	},
-+	{
-+		.name = "wmac1_irq",
-+		.flags = IORESOURCE_IRQ,
-+	}
-+};
-+
-+static struct platform_device ath25_wmac[] = {
-+	{
-+		.id = 0,
-+		.name = "ar231x-wmac",
-+		.resource = ath25_wmac0_res,
-+		.num_resources = ARRAY_SIZE(ath25_wmac0_res),
-+		.dev.platform_data = &ath25_board,
-+	},
-+	{
-+		.id = 1,
-+		.name = "ar231x-wmac",
-+		.resource = ath25_wmac1_res,
-+		.num_resources = ARRAY_SIZE(ath25_wmac1_res),
-+		.dev.platform_data = &ath25_board,
-+	},
-+};
-+
-+static const char * const soc_type_strings[] = {
-+	[ATH25_SOC_AR5312] = "Atheros AR5312",
-+	[ATH25_SOC_AR2312] = "Atheros AR2312",
-+	[ATH25_SOC_AR2313] = "Atheros AR2313",
-+	[ATH25_SOC_AR2315] = "Atheros AR2315",
-+	[ATH25_SOC_AR2316] = "Atheros AR2316",
-+	[ATH25_SOC_AR2317] = "Atheros AR2317",
-+	[ATH25_SOC_AR2318] = "Atheros AR2318",
-+	[ATH25_SOC_UNKNOWN] = "Atheros (unknown)",
-+};
-+
-+const char *get_system_type(void)
-+{
-+	if ((ath25_soc >= ARRAY_SIZE(soc_type_strings)) ||
-+	    !soc_type_strings[ath25_soc])
-+		return soc_type_strings[ATH25_SOC_UNKNOWN];
-+	return soc_type_strings[ath25_soc];
-+}
-+
-+void __init ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk)
-+{
-+	struct uart_port s;
-+
-+	memset(&s, 0, sizeof(s));
-+
-+	s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP;
-+	s.iotype = UPIO_MEM32;
-+	s.irq = irq;
-+	s.regshift = 2;
-+	s.mapbase = mapbase;
-+	s.uartclk = uartclk;
-+
-+	early_serial_setup(&s);
-+}
-+
-+int __init ath25_add_wmac(int nr, u32 base, int irq)
-+{
-+	struct resource *res;
-+
-+	ath25_wmac[nr].dev.platform_data = &ath25_board;
-+	res = &ath25_wmac[nr].resource[0];
-+	res->start = base;
-+	res->end = base + 0x10000 - 1;
-+	res++;
-+	res->start = irq;
-+	res->end = irq;
-+	return platform_device_register(&ath25_wmac[nr]);
-+}
-+
-+static int __init ath25_register_devices(void)
-+{
-+	if (is_ar5312())
-+		ar5312_init_devices();
-+	else
-+		ar2315_init_devices();
-+
-+	return 0;
-+}
-+
-+device_initcall(ath25_register_devices);
-+
-+static int __init ath25_arch_init(void)
-+{
-+	if (is_ar5312())
-+		ar5312_arch_init();
-+	else
-+		ar2315_arch_init();
-+
-+	return 0;
-+}
-+
-+arch_initcall(ath25_arch_init);
diff --git a/target/linux/ath25/patches-3.18/020-early-printk-support.patch b/target/linux/ath25/patches-3.18/020-early-printk-support.patch
deleted file mode 100644
index bd937d3..0000000
--- a/target/linux/ath25/patches-3.18/020-early-printk-support.patch
+++ /dev/null
@@ -1,68 +0,0 @@
---- /dev/null
-+++ b/arch/mips/ath25/early_printk.c
-@@ -0,0 +1,44 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2010 Gabor Juhos <juhosg@openwrt.org>
-+ */
-+
-+#include <linux/mm.h>
-+#include <linux/io.h>
-+#include <linux/serial_reg.h>
-+
-+#include "devices.h"
-+#include "ar2315_regs.h"
-+#include "ar5312_regs.h"
-+
-+static inline void prom_uart_wr(void __iomem *base, unsigned reg,
-+				unsigned char ch)
-+{
-+	__raw_writel(ch, base + 4 * reg);
-+}
-+
-+static inline unsigned char prom_uart_rr(void __iomem *base, unsigned reg)
-+{
-+	return __raw_readl(base + 4 * reg);
-+}
-+
-+void prom_putchar(unsigned char ch)
-+{
-+	static void __iomem *base;
-+
-+	if (unlikely(base == NULL)) {
-+		if (is_ar2315())
-+			base = (void __iomem *)(KSEG1ADDR(AR2315_UART0_BASE));
-+		else
-+			base = (void __iomem *)(KSEG1ADDR(AR5312_UART0_BASE));
-+	}
-+
-+	while ((prom_uart_rr(base, UART_LSR) & UART_LSR_THRE) == 0)
-+		;
-+	prom_uart_wr(base, UART_TX, ch);
-+	while ((prom_uart_rr(base, UART_LSR) & UART_LSR_THRE) == 0)
-+		;
-+}
---- a/arch/mips/ath25/Makefile
-+++ b/arch/mips/ath25/Makefile
-@@ -9,5 +9,8 @@
- #
- 
- obj-y += board.o prom.o devices.o
-+
-+obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
-+
- obj-$(CONFIG_SOC_AR5312) += ar5312.o
- obj-$(CONFIG_SOC_AR2315) += ar2315.o
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -106,6 +106,7 @@ config ATH25
- 	select SYS_HAS_CPU_MIPS32_R1
- 	select SYS_SUPPORTS_BIG_ENDIAN
- 	select SYS_SUPPORTS_32BIT_KERNEL
-+	select SYS_HAS_EARLY_PRINTK
- 	help
- 	  Support for Atheros AR231x and Atheros AR531x based boards
- 
diff --git a/target/linux/ath25/patches-3.18/030-ar2315_pci.patch b/target/linux/ath25/patches-3.18/030-ar2315_pci.patch
deleted file mode 100644
index 08b7463..0000000
--- a/target/linux/ath25/patches-3.18/030-ar2315_pci.patch
+++ /dev/null
@@ -1,613 +0,0 @@
---- a/arch/mips/pci/Makefile
-+++ b/arch/mips/pci/Makefile
-@@ -19,6 +19,7 @@ obj-$(CONFIG_BCM47XX)		+= pci-bcm47xx.o
- obj-$(CONFIG_BCM63XX)		+= pci-bcm63xx.o fixup-bcm63xx.o \
- 					ops-bcm63xx.o
- obj-$(CONFIG_MIPS_ALCHEMY)	+= pci-alchemy.o
-+obj-$(CONFIG_PCI_AR2315)	+= pci-ar2315.o
- obj-$(CONFIG_SOC_AR71XX)	+= pci-ar71xx.o
- obj-$(CONFIG_PCI_AR724X)	+= pci-ar724x.o
- obj-$(CONFIG_MIPS_PCI_VIRTIO)	+= pci-virtio-guest.o
---- /dev/null
-+++ b/arch/mips/pci/pci-ar2315.c
-@@ -0,0 +1,511 @@
-+/*
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * as published by the Free Software Foundation; either version 2
-+ * of the License, or (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
-+ */
-+
-+/**
-+ * Both AR2315 and AR2316 chips have PCI interface unit, which supports DMA
-+ * and interrupt. PCI interface supports MMIO access method, but does not
-+ * seem to support I/O ports.
-+ *
-+ * Read/write operation in the region 0x80000000-0xBFFFFFFF causes
-+ * a memory read/write command on the PCI bus. 30 LSBs of address on
-+ * the bus are taken from memory read/write request and 2 MSBs are
-+ * determined by PCI unit configuration.
-+ *
-+ * To work with the configuration space instead of memory is necessary set
-+ * the CFG_SEL bit in the PCI_MISC_CONFIG register.
-+ *
-+ * Devices on the bus can perform DMA requests via chip BAR1. PCI host
-+ * controller BARs are programmend as if an external device is programmed.
-+ * Which means that during configuration, IDSEL pin of the chip should be
-+ * asserted.
-+ *
-+ * We know (and support) only one board that uses the PCI interface -
-+ * Fonera 2.0g (FON2202). It has a USB EHCI controller connected to the
-+ * AR2315 PCI bus. IDSEL pin of USB controller is connected to AD[13] line
-+ * and IDSEL pin of AR2315 is connected to AD[16] line.
-+ */
-+
-+#include <linux/types.h>
-+#include <linux/pci.h>
-+#include <linux/platform_device.h>
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/mm.h>
-+#include <linux/delay.h>
-+#include <linux/bitops.h>
-+#include <linux/irq.h>
-+#include <linux/irqdomain.h>
-+#include <linux/io.h>
-+#include <asm/paccess.h>
-+
-+/*
-+ * PCI Bus Interface Registers
-+ */
-+#define AR2315_PCI_1MS_REG		0x0008
-+
-+#define AR2315_PCI_1MS_MASK		0x3FFFF	/* # of AHB clk cycles in 1ms */
-+
-+#define AR2315_PCI_MISC_CONFIG		0x000c
-+
-+#define AR2315_PCIMISC_TXD_EN	0x00000001	/* Enable TXD for fragments */
-+#define AR2315_PCIMISC_CFG_SEL	0x00000002	/* Mem or Config cycles */
-+#define AR2315_PCIMISC_GIG_MASK	0x0000000C	/* bits 31-30 for pci req */
-+#define AR2315_PCIMISC_RST_MODE	0x00000030
-+#define AR2315_PCIRST_INPUT	0x00000000	/* 4:5=0 rst is input */
-+#define AR2315_PCIRST_LOW	0x00000010	/* 4:5=1 rst to GND */
-+#define AR2315_PCIRST_HIGH	0x00000020	/* 4:5=2 rst to VDD */
-+#define AR2315_PCIGRANT_EN	0x00000000	/* 6:7=0 early grant en */
-+#define AR2315_PCIGRANT_FRAME	0x00000040	/* 6:7=1 grant waits 4 frame */
-+#define AR2315_PCIGRANT_IDLE	0x00000080	/* 6:7=2 grant waits 4 idle */
-+#define AR2315_PCIGRANT_GAP	0x00000000	/* 6:7=2 grant waits 4 idle */
-+#define AR2315_PCICACHE_DIS	0x00001000	/* PCI external access cache
-+						 * disable */
-+
-+#define AR2315_PCI_OUT_TSTAMP		0x0010
-+
-+#define AR2315_PCI_UNCACHE_CFG		0x0014
-+
-+#define AR2315_PCI_IN_EN		0x0100
-+
-+#define AR2315_PCI_IN_EN0	0x01	/* Enable chain 0 */
-+#define AR2315_PCI_IN_EN1	0x02	/* Enable chain 1 */
-+#define AR2315_PCI_IN_EN2	0x04	/* Enable chain 2 */
-+#define AR2315_PCI_IN_EN3	0x08	/* Enable chain 3 */
-+
-+#define AR2315_PCI_IN_DIS		0x0104
-+
-+#define AR2315_PCI_IN_DIS0	0x01	/* Disable chain 0 */
-+#define AR2315_PCI_IN_DIS1	0x02	/* Disable chain 1 */
-+#define AR2315_PCI_IN_DIS2	0x04	/* Disable chain 2 */
-+#define AR2315_PCI_IN_DIS3	0x08	/* Disable chain 3 */
-+
-+#define AR2315_PCI_IN_PTR		0x0200
-+
-+#define AR2315_PCI_OUT_EN		0x0400
-+
-+#define AR2315_PCI_OUT_EN0	0x01	/* Enable chain 0 */
-+
-+#define AR2315_PCI_OUT_DIS		0x0404
-+
-+#define AR2315_PCI_OUT_DIS0	0x01	/* Disable chain 0 */
-+
-+#define AR2315_PCI_OUT_PTR		0x0408
-+
-+/* PCI interrupt status (write one to clear) */
-+#define AR2315_PCI_ISR			0x0500
-+
-+#define AR2315_PCI_INT_TX	0x00000001	/* Desc In Completed */
-+#define AR2315_PCI_INT_TXOK	0x00000002	/* Desc In OK */
-+#define AR2315_PCI_INT_TXERR	0x00000004	/* Desc In ERR */
-+#define AR2315_PCI_INT_TXEOL	0x00000008	/* Desc In End-of-List */
-+#define AR2315_PCI_INT_RX	0x00000010	/* Desc Out Completed */
-+#define AR2315_PCI_INT_RXOK	0x00000020	/* Desc Out OK */
-+#define AR2315_PCI_INT_RXERR	0x00000040	/* Desc Out ERR */
-+#define AR2315_PCI_INT_RXEOL	0x00000080	/* Desc Out EOL */
-+#define AR2315_PCI_INT_TXOOD	0x00000200	/* Desc In Out-of-Desc */
-+#define AR2315_PCI_INT_DESCMASK	0x0000FFFF	/* Desc Mask */
-+#define AR2315_PCI_INT_EXT	0x02000000	/* Extern PCI INTA */
-+#define AR2315_PCI_INT_ABORT	0x04000000	/* PCI bus abort event */
-+
-+/* PCI interrupt mask */
-+#define AR2315_PCI_IMR			0x0504
-+
-+/* Global PCI interrupt enable */
-+#define AR2315_PCI_IER			0x0508
-+
-+#define AR2315_PCI_IER_DISABLE		0x00	/* disable pci interrupts */
-+#define AR2315_PCI_IER_ENABLE		0x01	/* enable pci interrupts */
-+
-+#define AR2315_PCI_HOST_IN_EN		0x0800
-+#define AR2315_PCI_HOST_IN_DIS		0x0804
-+#define AR2315_PCI_HOST_IN_PTR		0x0810
-+#define AR2315_PCI_HOST_OUT_EN		0x0900
-+#define AR2315_PCI_HOST_OUT_DIS		0x0904
-+#define AR2315_PCI_HOST_OUT_PTR		0x0908
-+
-+/*
-+ * PCI interrupts, which share IP5
-+ * Keep ordered according to AR2315_PCI_INT_XXX bits
-+ */
-+#define AR2315_PCI_IRQ_EXT		25
-+#define AR2315_PCI_IRQ_ABORT		26
-+#define AR2315_PCI_IRQ_COUNT		27
-+
-+/* Arbitrary size of memory region to access the configuration space */
-+#define AR2315_PCI_CFG_SIZE	0x00100000
-+
-+#define AR2315_PCI_HOST_SLOT	3
-+#define AR2315_PCI_HOST_DEVID	((0xff18 << 16) | PCI_VENDOR_ID_ATHEROS)
-+
-+/* ??? access BAR */
-+#define AR2315_PCI_HOST_MBAR0		0x10000000
-+/* RAM access BAR */
-+#define AR2315_PCI_HOST_MBAR1		AR2315_PCI_HOST_SDRAM_BASEADDR
-+/* ??? access BAR */
-+#define AR2315_PCI_HOST_MBAR2		0x30000000
-+
-+struct ar2315_pci_ctrl {
-+	void __iomem *cfg_mem;
-+	void __iomem *mmr_mem;
-+	unsigned irq;
-+	unsigned irq_ext;
-+	struct irq_domain *domain;
-+	struct pci_controller pci_ctrl;
-+	struct resource mem_res;
-+	struct resource io_res;
-+};
-+
-+static inline struct ar2315_pci_ctrl *ar2315_pci_bus_to_apc(struct pci_bus *bus)
-+{
-+	struct pci_controller *hose = bus->sysdata;
-+
-+	return container_of(hose, struct ar2315_pci_ctrl, pci_ctrl);
-+}
-+
-+static inline u32 ar2315_pci_reg_read(struct ar2315_pci_ctrl *apc, u32 reg)
-+{
-+	return __raw_readl(apc->mmr_mem + reg);
-+}
-+
-+static inline void ar2315_pci_reg_write(struct ar2315_pci_ctrl *apc, u32 reg,
-+					u32 val)
-+{
-+	__raw_writel(val, apc->mmr_mem + reg);
-+}
-+
-+static inline void ar2315_pci_reg_mask(struct ar2315_pci_ctrl *apc, u32 reg,
-+				       u32 mask, u32 val)
-+{
-+	u32 ret = ar2315_pci_reg_read(apc, reg);
-+
-+	ret &= ~mask;
-+	ret |= val;
-+	ar2315_pci_reg_write(apc, reg, ret);
-+}
-+
-+static int ar2315_pci_cfg_access(struct ar2315_pci_ctrl *apc, unsigned devfn,
-+				 int where, int size, u32 *ptr, bool write)
-+{
-+	int func = PCI_FUNC(devfn);
-+	int dev = PCI_SLOT(devfn);
-+	u32 addr = (1 << (13 + dev)) | (func << 8) | (where & ~3);
-+	u32 mask = 0xffffffff >> 8 * (4 - size);
-+	u32 sh = (where & 3) * 8;
-+	u32 value, isr;
-+
-+	/* Prevent access past the remapped area */
-+	if (addr >= AR2315_PCI_CFG_SIZE || dev > 18)
-+		return PCIBIOS_DEVICE_NOT_FOUND;
-+
-+	/* Clear pending errors */
-+	ar2315_pci_reg_write(apc, AR2315_PCI_ISR, AR2315_PCI_INT_ABORT);
-+	/* Select Configuration access */
-+	ar2315_pci_reg_mask(apc, AR2315_PCI_MISC_CONFIG, 0,
-+			    AR2315_PCIMISC_CFG_SEL);
-+
-+	mb();	/* PCI must see space change before we begin */
-+
-+	value = __raw_readl(apc->cfg_mem + addr);
-+
-+	isr = ar2315_pci_reg_read(apc, AR2315_PCI_ISR);
-+
-+	if (isr & AR2315_PCI_INT_ABORT)
-+		goto exit_err;
-+
-+	if (write) {
-+		value = (value & ~(mask << sh)) | *ptr << sh;
-+		__raw_writel(value, apc->cfg_mem + addr);
-+		isr = ar2315_pci_reg_read(apc, AR2315_PCI_ISR);
-+		if (isr & AR2315_PCI_INT_ABORT)
-+			goto exit_err;
-+	} else {
-+		*ptr = (value >> sh) & mask;
-+	}
-+
-+	goto exit;
-+
-+exit_err:
-+	ar2315_pci_reg_write(apc, AR2315_PCI_ISR, AR2315_PCI_INT_ABORT);
-+	if (!write)
-+		*ptr = 0xffffffff;
-+
-+exit:
-+	/* Select Memory access */
-+	ar2315_pci_reg_mask(apc, AR2315_PCI_MISC_CONFIG, AR2315_PCIMISC_CFG_SEL,
-+			    0);
-+
-+	return isr & AR2315_PCI_INT_ABORT ? PCIBIOS_DEVICE_NOT_FOUND :
-+					    PCIBIOS_SUCCESSFUL;
-+}
-+
-+static inline int ar2315_pci_local_cfg_rd(struct ar2315_pci_ctrl *apc,
-+					  unsigned devfn, int where, u32 *val)
-+{
-+	return ar2315_pci_cfg_access(apc, devfn, where, sizeof(u32), val,
-+				     false);
-+}
-+
-+static inline int ar2315_pci_local_cfg_wr(struct ar2315_pci_ctrl *apc,
-+					  unsigned devfn, int where, u32 val)
-+{
-+	return ar2315_pci_cfg_access(apc, devfn, where, sizeof(u32), &val,
-+				     true);
-+}
-+
-+static int ar2315_pci_cfg_read(struct pci_bus *bus, unsigned devfn, int where,
-+			       int size, u32 *value)
-+{
-+	struct ar2315_pci_ctrl *apc = ar2315_pci_bus_to_apc(bus);
-+
-+	if (PCI_SLOT(devfn) == AR2315_PCI_HOST_SLOT)
-+		return PCIBIOS_DEVICE_NOT_FOUND;
-+
-+	return ar2315_pci_cfg_access(apc, devfn, where, size, value, false);
-+}
-+
-+static int ar2315_pci_cfg_write(struct pci_bus *bus, unsigned devfn, int where,
-+				int size, u32 value)
-+{
-+	struct ar2315_pci_ctrl *apc = ar2315_pci_bus_to_apc(bus);
-+
-+	if (PCI_SLOT(devfn) == AR2315_PCI_HOST_SLOT)
-+		return PCIBIOS_DEVICE_NOT_FOUND;
-+
-+	return ar2315_pci_cfg_access(apc, devfn, where, size, &value, true);
-+}
-+
-+static struct pci_ops ar2315_pci_ops = {
-+	.read	= ar2315_pci_cfg_read,
-+	.write	= ar2315_pci_cfg_write,
-+};
-+
-+static int ar2315_pci_host_setup(struct ar2315_pci_ctrl *apc)
-+{
-+	unsigned devfn = PCI_DEVFN(AR2315_PCI_HOST_SLOT, 0);
-+	int res;
-+	u32 id;
-+
-+	res = ar2315_pci_local_cfg_rd(apc, devfn, PCI_VENDOR_ID, &id);
-+	if (res != PCIBIOS_SUCCESSFUL || id != AR2315_PCI_HOST_DEVID)
-+		return -ENODEV;
-+
-+	/* Program MBARs */
-+	ar2315_pci_local_cfg_wr(apc, devfn, PCI_BASE_ADDRESS_0,
-+				AR2315_PCI_HOST_MBAR0);
-+	ar2315_pci_local_cfg_wr(apc, devfn, PCI_BASE_ADDRESS_1,
-+				AR2315_PCI_HOST_MBAR1);
-+	ar2315_pci_local_cfg_wr(apc, devfn, PCI_BASE_ADDRESS_2,
-+				AR2315_PCI_HOST_MBAR2);
-+
-+	/* Run */
-+	ar2315_pci_local_cfg_wr(apc, devfn, PCI_COMMAND, PCI_COMMAND_MEMORY |
-+				PCI_COMMAND_MASTER | PCI_COMMAND_SPECIAL |
-+				PCI_COMMAND_INVALIDATE | PCI_COMMAND_PARITY |
-+				PCI_COMMAND_SERR | PCI_COMMAND_FAST_BACK);
-+
-+	return 0;
-+}
-+
-+static void ar2315_pci_irq_handler(unsigned irq, struct irq_desc *desc)
-+{
-+	struct ar2315_pci_ctrl *apc = irq_get_handler_data(irq);
-+	u32 pending = ar2315_pci_reg_read(apc, AR2315_PCI_ISR) &
-+		      ar2315_pci_reg_read(apc, AR2315_PCI_IMR);
-+	unsigned pci_irq = 0;
-+
-+	if (pending)
-+		pci_irq = irq_find_mapping(apc->domain, __ffs(pending));
-+
-+	if (pci_irq)
-+		generic_handle_irq(pci_irq);
-+	else
-+		spurious_interrupt();
-+}
-+
-+static void ar2315_pci_irq_mask(struct irq_data *d)
-+{
-+	struct ar2315_pci_ctrl *apc = irq_data_get_irq_chip_data(d);
-+
-+	ar2315_pci_reg_mask(apc, AR2315_PCI_IMR, BIT(d->hwirq), 0);
-+}
-+
-+static void ar2315_pci_irq_mask_ack(struct irq_data *d)
-+{
-+	struct ar2315_pci_ctrl *apc = irq_data_get_irq_chip_data(d);
-+	u32 m = BIT(d->hwirq);
-+
-+	ar2315_pci_reg_mask(apc, AR2315_PCI_IMR, m, 0);
-+	ar2315_pci_reg_write(apc, AR2315_PCI_ISR, m);
-+}
-+
-+static void ar2315_pci_irq_unmask(struct irq_data *d)
-+{
-+	struct ar2315_pci_ctrl *apc = irq_data_get_irq_chip_data(d);
-+
-+	ar2315_pci_reg_mask(apc, AR2315_PCI_IMR, 0, BIT(d->hwirq));
-+}
-+
-+static struct irq_chip ar2315_pci_irq_chip = {
-+	.name = "AR2315-PCI",
-+	.irq_mask = ar2315_pci_irq_mask,
-+	.irq_mask_ack = ar2315_pci_irq_mask_ack,
-+	.irq_unmask = ar2315_pci_irq_unmask,
-+};
-+
-+static int ar2315_pci_irq_map(struct irq_domain *d, unsigned irq,
-+			      irq_hw_number_t hw)
-+{
-+	irq_set_chip_and_handler(irq, &ar2315_pci_irq_chip, handle_level_irq);
-+	irq_set_chip_data(irq, d->host_data);
-+	return 0;
-+}
-+
-+static struct irq_domain_ops ar2315_pci_irq_domain_ops = {
-+	.map = ar2315_pci_irq_map,
-+};
-+
-+static void ar2315_pci_irq_init(struct ar2315_pci_ctrl *apc)
-+{
-+	ar2315_pci_reg_mask(apc, AR2315_PCI_IER, AR2315_PCI_IER_ENABLE, 0);
-+	ar2315_pci_reg_mask(apc, AR2315_PCI_IMR, (AR2315_PCI_INT_ABORT |
-+			    AR2315_PCI_INT_EXT), 0);
-+
-+	apc->irq_ext = irq_create_mapping(apc->domain, AR2315_PCI_IRQ_EXT);
-+
-+	irq_set_chained_handler(apc->irq, ar2315_pci_irq_handler);
-+	irq_set_handler_data(apc->irq, apc);
-+
-+	/* Clear any pending Abort or external Interrupts
-+	 * and enable interrupt processing */
-+	ar2315_pci_reg_write(apc, AR2315_PCI_ISR, AR2315_PCI_INT_ABORT |
-+						  AR2315_PCI_INT_EXT);
-+	ar2315_pci_reg_mask(apc, AR2315_PCI_IER, 0, AR2315_PCI_IER_ENABLE);
-+}
-+
-+static int ar2315_pci_probe(struct platform_device *pdev)
-+{
-+	struct ar2315_pci_ctrl *apc;
-+	struct device *dev = &pdev->dev;
-+	struct resource *res;
-+	int irq, err;
-+
-+	apc = devm_kzalloc(dev, sizeof(*apc), GFP_KERNEL);
-+	if (!apc)
-+		return -ENOMEM;
-+
-+	irq = platform_get_irq(pdev, 0);
-+	if (irq < 0)
-+		return -EINVAL;
-+	apc->irq = irq;
-+
-+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-+					   "ar2315-pci-ctrl");
-+	apc->mmr_mem = devm_ioremap_resource(dev, res);
-+	if (IS_ERR(apc->mmr_mem))
-+		return PTR_ERR(apc->mmr_mem);
-+
-+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-+					   "ar2315-pci-ext");
-+	if (!res)
-+		return -EINVAL;
-+
-+	apc->mem_res.name = "AR2315 PCI mem space";
-+	apc->mem_res.parent = res;
-+	apc->mem_res.start = res->start;
-+	apc->mem_res.end = res->end;
-+	apc->mem_res.flags = IORESOURCE_MEM;
-+
-+	/* Remap PCI config space */
-+	apc->cfg_mem = devm_ioremap_nocache(dev, res->start,
-+					    AR2315_PCI_CFG_SIZE);
-+	if (!apc->cfg_mem) {
-+		dev_err(dev, "failed to remap PCI config space\n");
-+		return -ENOMEM;
-+	}
-+
-+	/* Reset the PCI bus by setting bits 5-4 in PCI_MCFG */
-+	ar2315_pci_reg_mask(apc, AR2315_PCI_MISC_CONFIG,
-+			    AR2315_PCIMISC_RST_MODE,
-+			    AR2315_PCIRST_LOW);
-+	msleep(100);
-+
-+	/* Bring the PCI out of reset */
-+	ar2315_pci_reg_mask(apc, AR2315_PCI_MISC_CONFIG,
-+			    AR2315_PCIMISC_RST_MODE,
-+			    AR2315_PCIRST_HIGH | AR2315_PCICACHE_DIS | 0x8);
-+
-+	ar2315_pci_reg_write(apc, AR2315_PCI_UNCACHE_CFG,
-+			     0x1E | /* 1GB uncached */
-+			     (1 << 5) | /* Enable uncached */
-+			     (0x2 << 30) /* Base: 0x80000000 */);
-+	ar2315_pci_reg_read(apc, AR2315_PCI_UNCACHE_CFG);
-+
-+	msleep(500);
-+
-+	err = ar2315_pci_host_setup(apc);
-+	if (err)
-+		return err;
-+
-+	apc->domain = irq_domain_add_linear(NULL, AR2315_PCI_IRQ_COUNT,
-+					    &ar2315_pci_irq_domain_ops, apc);
-+	if (!apc->domain) {
-+		dev_err(dev, "failed to add IRQ domain\n");
-+		return -ENOMEM;
-+	}
-+
-+	ar2315_pci_irq_init(apc);
-+
-+	/* PCI controller does not support I/O ports */
-+	apc->io_res.name = "AR2315 IO space";
-+	apc->io_res.start = 0;
-+	apc->io_res.end = 0;
-+	apc->io_res.flags = IORESOURCE_IO,
-+
-+	apc->pci_ctrl.pci_ops = &ar2315_pci_ops;
-+	apc->pci_ctrl.mem_resource = &apc->mem_res,
-+	apc->pci_ctrl.io_resource = &apc->io_res,
-+
-+	register_pci_controller(&apc->pci_ctrl);
-+
-+	dev_info(dev, "register PCI controller\n");
-+
-+	return 0;
-+}
-+
-+static struct platform_driver ar2315_pci_driver = {
-+	.probe = ar2315_pci_probe,
-+	.driver = {
-+		.name = "ar2315-pci",
-+		.owner = THIS_MODULE,
-+	},
-+};
-+
-+static int __init ar2315_pci_init(void)
-+{
-+	return platform_driver_register(&ar2315_pci_driver);
-+}
-+arch_initcall(ar2315_pci_init);
-+
-+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-+{
-+	struct ar2315_pci_ctrl *apc = ar2315_pci_bus_to_apc(dev->bus);
-+
-+	return slot ? 0 : apc->irq_ext;
-+}
-+
-+int pcibios_plat_dev_init(struct pci_dev *dev)
-+{
-+	return 0;
-+}
---- a/arch/mips/ath25/Kconfig
-+++ b/arch/mips/ath25/Kconfig
-@@ -7,3 +7,10 @@ config SOC_AR2315
- 	bool "Atheros AR2315+ SoC support"
- 	depends on ATH25
- 	default y
-+
-+config PCI_AR2315
-+	bool "Atheros AR2315 PCI controller support"
-+	depends on SOC_AR2315
-+	select HW_HAS_PCI
-+	select PCI
-+	default y
---- a/arch/mips/ath25/ar2315.c
-+++ b/arch/mips/ath25/ar2315.c
-@@ -134,6 +134,10 @@ static void ar2315_irq_dispatch(void)
- 
- 	if (pending & CAUSEF_IP3)
- 		do_IRQ(AR2315_IRQ_WLAN0);
-+#ifdef CONFIG_PCI_AR2315
-+	else if (pending & CAUSEF_IP5)
-+		do_IRQ(AR2315_IRQ_LCBUS_PCI);
-+#endif
- 	else if (pending & CAUSEF_IP2)
- 		do_IRQ(AR2315_IRQ_MISC);
- 	else if (pending & CAUSEF_IP7)
-@@ -299,10 +303,62 @@ void __init ar2315_plat_mem_setup(void)
- 	_machine_restart = ar2315_restart;
- }
- 
-+#ifdef CONFIG_PCI_AR2315
-+static struct resource ar2315_pci_res[] = {
-+	{
-+		.name = "ar2315-pci-ctrl",
-+		.flags = IORESOURCE_MEM,
-+		.start = AR2315_PCI_BASE,
-+		.end = AR2315_PCI_BASE + AR2315_PCI_SIZE - 1,
-+	},
-+	{
-+		.name = "ar2315-pci-ext",
-+		.flags = IORESOURCE_MEM,
-+		.start = AR2315_PCI_EXT_BASE,
-+		.end = AR2315_PCI_EXT_BASE + AR2315_PCI_EXT_SIZE - 1,
-+	},
-+	{
-+		.name = "ar2315-pci",
-+		.flags = IORESOURCE_IRQ,
-+		.start = AR2315_IRQ_LCBUS_PCI,
-+		.end = AR2315_IRQ_LCBUS_PCI,
-+	},
-+};
-+#endif
-+
- void __init ar2315_arch_init(void)
- {
- 	unsigned irq = irq_create_mapping(ar2315_misc_irq_domain,
- 					  AR2315_MISC_IRQ_UART0);
- 
- 	ath25_serial_setup(AR2315_UART0_BASE, irq, ar2315_apb_frequency());
-+
-+#ifdef CONFIG_PCI_AR2315
-+	if (ath25_soc == ATH25_SOC_AR2315) {
-+		/* Reset PCI DMA logic */
-+		ar2315_rst_reg_mask(AR2315_RESET, 0, AR2315_RESET_PCIDMA);
-+		msleep(20);
-+		ar2315_rst_reg_mask(AR2315_RESET, AR2315_RESET_PCIDMA, 0);
-+		msleep(20);
-+
-+		/* Configure endians */
-+		ar2315_rst_reg_mask(AR2315_ENDIAN_CTL, 0, AR2315_CONFIG_PCIAHB |
-+				    AR2315_CONFIG_PCIAHB_BRIDGE);
-+
-+		/* Configure as PCI host with DMA */
-+		ar2315_rst_reg_write(AR2315_PCICLK, AR2315_PCICLK_PLLC_CLKM |
-+				  (AR2315_PCICLK_IN_FREQ_DIV_6 <<
-+				   AR2315_PCICLK_DIV_S));
-+		ar2315_rst_reg_mask(AR2315_AHB_ARB_CTL, 0, AR2315_ARB_PCI);
-+		ar2315_rst_reg_mask(AR2315_IF_CTL, AR2315_IF_PCI_CLK_MASK |
-+				    AR2315_IF_MASK, AR2315_IF_PCI |
-+				    AR2315_IF_PCI_HOST | AR2315_IF_PCI_INTR |
-+				    (AR2315_IF_PCI_CLK_OUTPUT_CLK <<
-+				     AR2315_IF_PCI_CLK_SHIFT));
-+
-+		platform_device_register_simple("ar2315-pci", -1,
-+						ar2315_pci_res,
-+						ARRAY_SIZE(ar2315_pci_res));
-+	}
-+#endif
- }
diff --git a/target/linux/ath25/patches-3.18/107-ar5312_gpio.patch b/target/linux/ath25/patches-3.18/107-ar5312_gpio.patch
deleted file mode 100644
index a6d0a88..0000000
--- a/target/linux/ath25/patches-3.18/107-ar5312_gpio.patch
+++ /dev/null
@@ -1,212 +0,0 @@
---- a/arch/mips/ath25/Kconfig
-+++ b/arch/mips/ath25/Kconfig
-@@ -1,6 +1,7 @@
- config SOC_AR5312
- 	bool "Atheros AR5312/AR2312+ SoC support"
- 	depends on ATH25
-+	select GPIO_AR5312
- 	default y
- 
- config SOC_AR2315
---- a/arch/mips/ath25/ar5312.c
-+++ b/arch/mips/ath25/ar5312.c
-@@ -22,6 +22,7 @@
- #include <linux/platform_device.h>
- #include <linux/mtd/physmap.h>
- #include <linux/reboot.h>
-+#include <linux/gpio.h>
- #include <asm/bootinfo.h>
- #include <asm/reboot.h>
- #include <asm/time.h>
-@@ -180,6 +181,22 @@ static struct platform_device ar5312_phy
- 	.num_resources = 1,
- };
- 
-+static struct resource ar5312_gpio_res[] = {
-+	{
-+		.name = "ar5312-gpio",
-+		.flags = IORESOURCE_MEM,
-+		.start = AR5312_GPIO_BASE,
-+		.end = AR5312_GPIO_BASE + AR5312_GPIO_SIZE - 1,
-+	},
-+};
-+
-+static struct platform_device ar5312_gpio = {
-+	.name = "ar5312-gpio",
-+	.id = -1,
-+	.resource = ar5312_gpio_res,
-+	.num_resources = ARRAY_SIZE(ar5312_gpio_res),
-+};
-+
- static void __init ar5312_flash_init(void)
- {
- 	void __iomem *flashctl_base;
-@@ -247,6 +264,8 @@ void __init ar5312_init_devices(void)
- 
- 	platform_device_register(&ar5312_physmap_flash);
- 
-+	platform_device_register(&ar5312_gpio);
-+
- 	switch (ath25_soc) {
- 	case ATH25_SOC_AR5312:
- 		if (!ath25_board.radio)
---- a/drivers/gpio/Kconfig
-+++ b/drivers/gpio/Kconfig
-@@ -112,6 +112,13 @@ config GPIO_MAX730X
- 
- comment "Memory mapped GPIO drivers:"
- 
-+config GPIO_AR5312
-+	bool "AR5312 SoC GPIO support"
-+	default y if SOC_AR5312
-+	depends on SOC_AR5312
-+	help
-+	  Say yes here to enable GPIO support for Atheros AR5312/AR2312+ SoCs.
-+
- config GPIO_CLPS711X
- 	tristate "CLPS711X GPIO support"
- 	depends on ARCH_CLPS711X || COMPILE_TEST
---- a/drivers/gpio/Makefile
-+++ b/drivers/gpio/Makefile
-@@ -17,6 +17,7 @@ obj-$(CONFIG_GPIO_ADNP)		+= gpio-adnp.o
- obj-$(CONFIG_GPIO_ADP5520)	+= gpio-adp5520.o
- obj-$(CONFIG_GPIO_ADP5588)	+= gpio-adp5588.o
- obj-$(CONFIG_GPIO_AMD8111)	+= gpio-amd8111.o
-+obj-$(CONFIG_GPIO_AR5312)	+= gpio-ar5312.o
- obj-$(CONFIG_GPIO_ARIZONA)	+= gpio-arizona.o
- obj-$(CONFIG_GPIO_BCM_KONA)	+= gpio-bcm-kona.o
- obj-$(CONFIG_GPIO_BT8XX)	+= gpio-bt8xx.o
---- /dev/null
-+++ b/drivers/gpio/gpio-ar5312.c
-@@ -0,0 +1,121 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
-+ * Copyright (C) 2006 FON Technology, SL.
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
-+ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <linux/gpio.h>
-+
-+#define DRIVER_NAME	"ar5312-gpio"
-+
-+#define AR5312_GPIO_DO		0x00		/* output register */
-+#define AR5312_GPIO_DI		0x04		/* intput register */
-+#define AR5312_GPIO_CR		0x08		/* control register */
-+
-+#define AR5312_GPIO_CR_M(x)	(1 << (x))	/* mask for i/o */
-+#define AR5312_GPIO_CR_O(x)	(0 << (x))	/* mask for output */
-+#define AR5312_GPIO_CR_I(x)	(1 << (x))	/* mask for input */
-+#define AR5312_GPIO_CR_INT(x)	(1 << ((x)+8))	/* mask for interrupt */
-+#define AR5312_GPIO_CR_UART(x)	(1 << ((x)+16))	/* uart multiplex */
-+
-+#define AR5312_GPIO_NUM		8
-+
-+static void __iomem *ar5312_mem;
-+
-+static inline u32 ar5312_gpio_reg_read(unsigned reg)
-+{
-+	return __raw_readl(ar5312_mem + reg);
-+}
-+
-+static inline void ar5312_gpio_reg_write(unsigned reg, u32 val)
-+{
-+	__raw_writel(val, ar5312_mem + reg);
-+}
-+
-+static inline void ar5312_gpio_reg_mask(unsigned reg, u32 mask, u32 val)
-+{
-+	ar5312_gpio_reg_write(reg, (ar5312_gpio_reg_read(reg) & ~mask) | val);
-+}
-+
-+static int ar5312_gpio_get_val(struct gpio_chip *chip, unsigned gpio)
-+{
-+	return (ar5312_gpio_reg_read(AR5312_GPIO_DI) >> gpio) & 1;
-+}
-+
-+static void ar5312_gpio_set_val(struct gpio_chip *chip, unsigned gpio, int val)
-+{
-+	u32 reg = ar5312_gpio_reg_read(AR5312_GPIO_DO);
-+
-+	reg = val ? reg | (1 << gpio) : reg & ~(1 << gpio);
-+	ar5312_gpio_reg_write(AR5312_GPIO_DO, reg);
-+}
-+
-+static int ar5312_gpio_dir_in(struct gpio_chip *chip, unsigned gpio)
-+{
-+	ar5312_gpio_reg_mask(AR5312_GPIO_CR, 0, 1 << gpio);
-+	return 0;
-+}
-+
-+static int ar5312_gpio_dir_out(struct gpio_chip *chip, unsigned gpio, int val)
-+{
-+	ar5312_gpio_reg_mask(AR5312_GPIO_CR, 1 << gpio, 0);
-+	ar5312_gpio_set_val(chip, gpio, val);
-+	return 0;
-+}
-+
-+static struct gpio_chip ar5312_gpio_chip = {
-+	.label			= DRIVER_NAME,
-+	.direction_input	= ar5312_gpio_dir_in,
-+	.direction_output	= ar5312_gpio_dir_out,
-+	.set			= ar5312_gpio_set_val,
-+	.get			= ar5312_gpio_get_val,
-+	.base			= 0,
-+	.ngpio			= AR5312_GPIO_NUM,
-+};
-+
-+static int ar5312_gpio_probe(struct platform_device *pdev)
-+{
-+	struct device *dev = &pdev->dev;
-+	struct resource *res;
-+	int ret;
-+
-+	if (ar5312_mem)
-+		return -EBUSY;
-+
-+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+	ar5312_mem = devm_ioremap_resource(dev, res);
-+	if (IS_ERR(ar5312_mem))
-+		return PTR_ERR(ar5312_mem);
-+
-+	ar5312_gpio_chip.dev = dev;
-+	ret = gpiochip_add(&ar5312_gpio_chip);
-+	if (ret) {
-+		dev_err(dev, "failed to add gpiochip\n");
-+		return ret;
-+	}
-+
-+	return 0;
-+}
-+
-+static struct platform_driver ar5312_gpio_driver = {
-+	.probe = ar5312_gpio_probe,
-+	.driver = {
-+		.name = DRIVER_NAME,
-+		.owner = THIS_MODULE,
-+	}
-+};
-+
-+static int __init ar5312_gpio_init(void)
-+{
-+	return platform_driver_register(&ar5312_gpio_driver);
-+}
-+subsys_initcall(ar5312_gpio_init);
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -107,6 +107,7 @@ config ATH25
- 	select SYS_SUPPORTS_BIG_ENDIAN
- 	select SYS_SUPPORTS_32BIT_KERNEL
- 	select SYS_HAS_EARLY_PRINTK
-+	select ARCH_REQUIRE_GPIOLIB
- 	help
- 	  Support for Atheros AR231x and Atheros AR531x based boards
- 
diff --git a/target/linux/ath25/patches-3.18/108-ar2315_gpio.patch b/target/linux/ath25/patches-3.18/108-ar2315_gpio.patch
deleted file mode 100644
index 5d97853..0000000
--- a/target/linux/ath25/patches-3.18/108-ar2315_gpio.patch
+++ /dev/null
@@ -1,363 +0,0 @@
---- a/arch/mips/ath25/Kconfig
-+++ b/arch/mips/ath25/Kconfig
-@@ -7,6 +7,7 @@ config SOC_AR5312
- config SOC_AR2315
- 	bool "Atheros AR2315+ SoC support"
- 	depends on ATH25
-+	select GPIO_AR2315
- 	default y
- 
- config PCI_AR2315
---- a/arch/mips/ath25/ar2315.c
-+++ b/arch/mips/ath25/ar2315.c
-@@ -21,6 +21,8 @@
- #include <linux/interrupt.h>
- #include <linux/platform_device.h>
- #include <linux/reboot.h>
-+#include <linux/delay.h>
-+#include <linux/gpio.h>
- #include <asm/bootinfo.h>
- #include <asm/reboot.h>
- #include <asm/time.h>
-@@ -167,11 +169,42 @@ void __init ar2315_arch_init_irq(void)
- 	ar2315_misc_irq_domain = domain;
- }
- 
-+static struct resource ar2315_gpio_res[] = {
-+	{
-+		.name = "ar2315-gpio",
-+		.flags = IORESOURCE_MEM,
-+		.start = AR2315_RST_BASE + AR2315_GPIO,
-+		.end = AR2315_RST_BASE + AR2315_GPIO + 0x10 - 1,
-+	},
-+	{
-+		.name = "ar2315-gpio",
-+		.flags = IORESOURCE_IRQ,
-+	},
-+	{
-+		.name = "ar2315-gpio-irq-base",
-+		.flags = IORESOURCE_IRQ,
-+		.start = AR231X_GPIO_IRQ_BASE,
-+		.end = AR231X_GPIO_IRQ_BASE,
-+	}
-+};
-+
-+static struct platform_device ar2315_gpio = {
-+	.id = -1,
-+	.name = "ar2315-gpio",
-+	.resource = ar2315_gpio_res,
-+	.num_resources = ARRAY_SIZE(ar2315_gpio_res)
-+};
-+
- void __init ar2315_init_devices(void)
- {
- 	/* Find board configuration */
- 	ath25_find_config(AR2315_SPI_READ_BASE, AR2315_SPI_READ_SIZE);
- 
-+	ar2315_gpio_res[1].start = irq_create_mapping(ar2315_misc_irq_domain,
-+						      AR2315_MISC_IRQ_GPIO);
-+	ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
-+	platform_device_register(&ar2315_gpio);
-+
- 	ath25_add_wmac(0, AR2315_WLAN0_BASE, AR2315_IRQ_WLAN0);
- }
- 
-@@ -187,8 +220,8 @@ static void ar2315_restart(char *command
- 	/* Cold reset does not work on the AR2315/6, use the GPIO reset bits
- 	 * a workaround. Give it some time to attempt a gpio based hardware
- 	 * reset (atheros reference design workaround) */
--
--	/* TODO: implement the GPIO reset workaround */
-+	gpio_request_one(AR2315_RESET_GPIO, GPIOF_OUT_INIT_LOW, "Reset");
-+	mdelay(100);
- 
- 	/* Some boards (e.g. Senao EOC-2610) don't implement the reset logic
- 	 * workaround. Attempt to jump to the mips reset location -
---- a/drivers/gpio/Kconfig
-+++ b/drivers/gpio/Kconfig
-@@ -112,6 +112,13 @@ config GPIO_MAX730X
- 
- comment "Memory mapped GPIO drivers:"
- 
-+config GPIO_AR2315
-+	bool "AR2315 SoC GPIO support"
-+	default y if SOC_AR2315
-+	depends on SOC_AR2315
-+	help
-+	  Say yes here to enable GPIO support for Atheros AR2315+ SoCs.
-+
- config GPIO_AR5312
- 	bool "AR5312 SoC GPIO support"
- 	default y if SOC_AR5312
---- a/drivers/gpio/Makefile
-+++ b/drivers/gpio/Makefile
-@@ -17,6 +17,7 @@ obj-$(CONFIG_GPIO_ADNP)		+= gpio-adnp.o
- obj-$(CONFIG_GPIO_ADP5520)	+= gpio-adp5520.o
- obj-$(CONFIG_GPIO_ADP5588)	+= gpio-adp5588.o
- obj-$(CONFIG_GPIO_AMD8111)	+= gpio-amd8111.o
-+obj-$(CONFIG_GPIO_AR2315)	+= gpio-ar2315.o
- obj-$(CONFIG_GPIO_AR5312)	+= gpio-ar5312.o
- obj-$(CONFIG_GPIO_ARIZONA)	+= gpio-arizona.o
- obj-$(CONFIG_GPIO_BCM_KONA)	+= gpio-bcm-kona.o
---- /dev/null
-+++ b/drivers/gpio/gpio-ar2315.c
-@@ -0,0 +1,233 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
-+ * Copyright (C) 2006 FON Technology, SL.
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
-+ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <linux/gpio.h>
-+#include <linux/irq.h>
-+
-+#define DRIVER_NAME	"ar2315-gpio"
-+
-+#define AR2315_GPIO_DI			0x0000
-+#define AR2315_GPIO_DO			0x0008
-+#define AR2315_GPIO_DIR			0x0010
-+#define AR2315_GPIO_INT			0x0018
-+
-+#define AR2315_GPIO_DIR_M(x)		(1 << (x))	/* mask for i/o */
-+#define AR2315_GPIO_DIR_O(x)		(1 << (x))	/* output */
-+#define AR2315_GPIO_DIR_I(x)		(0)		/* input */
-+
-+#define AR2315_GPIO_INT_NUM_M		0x3F		/* mask for GPIO num */
-+#define AR2315_GPIO_INT_TRIG(x)		((x) << 6)	/* interrupt trigger */
-+#define AR2315_GPIO_INT_TRIG_M		(0x3 << 6)	/* mask for int trig */
-+
-+#define AR2315_GPIO_INT_TRIG_OFF	0	/* Triggerring off */
-+#define AR2315_GPIO_INT_TRIG_LOW	1	/* Low Level Triggered */
-+#define AR2315_GPIO_INT_TRIG_HIGH	2	/* High Level Triggered */
-+#define AR2315_GPIO_INT_TRIG_EDGE	3	/* Edge Triggered */
-+
-+#define AR2315_GPIO_NUM		22
-+
-+static u32 ar2315_gpio_intmask;
-+static u32 ar2315_gpio_intval;
-+static unsigned ar2315_gpio_irq_base;
-+static void __iomem *ar2315_mem;
-+
-+static inline u32 ar2315_gpio_reg_read(unsigned reg)
-+{
-+	return __raw_readl(ar2315_mem + reg);
-+}
-+
-+static inline void ar2315_gpio_reg_write(unsigned reg, u32 val)
-+{
-+	__raw_writel(val, ar2315_mem + reg);
-+}
-+
-+static inline void ar2315_gpio_reg_mask(unsigned reg, u32 mask, u32 val)
-+{
-+	ar2315_gpio_reg_write(reg, (ar2315_gpio_reg_read(reg) & ~mask) | val);
-+}
-+
-+static void ar2315_gpio_irq_handler(unsigned irq, struct irq_desc *desc)
-+{
-+	u32 pend;
-+	int bit = -1;
-+
-+	/* only do one gpio interrupt at a time */
-+	pend = ar2315_gpio_reg_read(AR2315_GPIO_DI);
-+	pend ^= ar2315_gpio_intval;
-+	pend &= ar2315_gpio_intmask;
-+
-+	if (pend) {
-+		bit = fls(pend) - 1;
-+		pend &= ~(1 << bit);
-+		ar2315_gpio_intval ^= (1 << bit);
-+	}
-+
-+	/* Enable interrupt with edge detection */
-+	if ((ar2315_gpio_reg_read(AR2315_GPIO_DIR) & AR2315_GPIO_DIR_M(bit)) !=
-+	    AR2315_GPIO_DIR_I(bit))
-+		return;
-+
-+	if (bit >= 0)
-+		generic_handle_irq(ar2315_gpio_irq_base + bit);
-+}
-+
-+static void ar2315_gpio_int_setup(unsigned gpio, int trig)
-+{
-+	u32 reg = ar2315_gpio_reg_read(AR2315_GPIO_INT);
-+
-+	reg &= ~(AR2315_GPIO_INT_NUM_M | AR2315_GPIO_INT_TRIG_M);
-+	reg |= gpio | AR2315_GPIO_INT_TRIG(trig);
-+	ar2315_gpio_reg_write(AR2315_GPIO_INT, reg);
-+}
-+
-+static void ar2315_gpio_irq_unmask(struct irq_data *d)
-+{
-+	unsigned gpio = d->irq - ar2315_gpio_irq_base;
-+	u32 dir = ar2315_gpio_reg_read(AR2315_GPIO_DIR);
-+
-+	/* Enable interrupt with edge detection */
-+	if ((dir & AR2315_GPIO_DIR_M(gpio)) != AR2315_GPIO_DIR_I(gpio))
-+		return;
-+
-+	ar2315_gpio_intmask |= (1 << gpio);
-+	ar2315_gpio_int_setup(gpio, AR2315_GPIO_INT_TRIG_EDGE);
-+}
-+
-+static void ar2315_gpio_irq_mask(struct irq_data *d)
-+{
-+	unsigned gpio = d->irq - ar2315_gpio_irq_base;
-+
-+	/* Disable interrupt */
-+	ar2315_gpio_intmask &= ~(1 << gpio);
-+	ar2315_gpio_int_setup(gpio, AR2315_GPIO_INT_TRIG_OFF);
-+}
-+
-+static struct irq_chip ar2315_gpio_irq_chip = {
-+	.name		= DRIVER_NAME,
-+	.irq_unmask	= ar2315_gpio_irq_unmask,
-+	.irq_mask	= ar2315_gpio_irq_mask,
-+};
-+
-+static void ar2315_gpio_irq_init(unsigned irq)
-+{
-+	unsigned i;
-+
-+	ar2315_gpio_intval = ar2315_gpio_reg_read(AR2315_GPIO_DI);
-+	for (i = 0; i < AR2315_GPIO_NUM; i++) {
-+		unsigned _irq = ar2315_gpio_irq_base + i;
-+
-+		irq_set_chip_and_handler(_irq, &ar2315_gpio_irq_chip,
-+					 handle_level_irq);
-+	}
-+	irq_set_chained_handler(irq, ar2315_gpio_irq_handler);
-+}
-+
-+static int ar2315_gpio_get_val(struct gpio_chip *chip, unsigned gpio)
-+{
-+	return (ar2315_gpio_reg_read(AR2315_GPIO_DI) >> gpio) & 1;
-+}
-+
-+static void ar2315_gpio_set_val(struct gpio_chip *chip, unsigned gpio, int val)
-+{
-+	u32 reg = ar2315_gpio_reg_read(AR2315_GPIO_DO);
-+
-+	reg = val ? reg | (1 << gpio) : reg & ~(1 << gpio);
-+	ar2315_gpio_reg_write(AR2315_GPIO_DO, reg);
-+}
-+
-+static int ar2315_gpio_dir_in(struct gpio_chip *chip, unsigned gpio)
-+{
-+	ar2315_gpio_reg_mask(AR2315_GPIO_DIR, 1 << gpio, 0);
-+	return 0;
-+}
-+
-+static int ar2315_gpio_dir_out(struct gpio_chip *chip, unsigned gpio, int val)
-+{
-+	ar2315_gpio_reg_mask(AR2315_GPIO_DIR, 0, 1 << gpio);
-+	ar2315_gpio_set_val(chip, gpio, val);
-+	return 0;
-+}
-+
-+static int ar2315_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
-+{
-+	return ar2315_gpio_irq_base + gpio;
-+}
-+
-+static struct gpio_chip ar2315_gpio_chip = {
-+	.label			= DRIVER_NAME,
-+	.direction_input	= ar2315_gpio_dir_in,
-+	.direction_output	= ar2315_gpio_dir_out,
-+	.set			= ar2315_gpio_set_val,
-+	.get			= ar2315_gpio_get_val,
-+	.to_irq			= ar2315_gpio_to_irq,
-+	.base			= 0,
-+	.ngpio			= AR2315_GPIO_NUM,
-+};
-+
-+static int ar2315_gpio_probe(struct platform_device *pdev)
-+{
-+	struct device *dev = &pdev->dev;
-+	struct resource *res;
-+	unsigned irq;
-+	int ret;
-+
-+	if (ar2315_mem)
-+		return -EBUSY;
-+
-+	res = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
-+					   "ar2315-gpio-irq-base");
-+	if (!res) {
-+		dev_err(dev, "not found GPIO IRQ base\n");
-+		return -ENXIO;
-+	}
-+	ar2315_gpio_irq_base = res->start;
-+
-+	res = platform_get_resource_byname(pdev, IORESOURCE_IRQ, DRIVER_NAME);
-+	if (!res) {
-+		dev_err(dev, "not found IRQ number\n");
-+		return -ENXIO;
-+	}
-+	irq = res->start;
-+
-+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, DRIVER_NAME);
-+	ar2315_mem = devm_ioremap_resource(dev, res);
-+	if (IS_ERR(ar2315_mem))
-+		return PTR_ERR(ar2315_mem);
-+
-+	ar2315_gpio_chip.dev = dev;
-+	ret = gpiochip_add(&ar2315_gpio_chip);
-+	if (ret) {
-+		dev_err(dev, "failed to add gpiochip\n");
-+		return ret;
-+	}
-+
-+	ar2315_gpio_irq_init(irq);
-+
-+	return 0;
-+}
-+
-+static struct platform_driver ar2315_gpio_driver = {
-+	.probe = ar2315_gpio_probe,
-+	.driver = {
-+		.name = DRIVER_NAME,
-+		.owner = THIS_MODULE,
-+	}
-+};
-+
-+static int __init ar2315_gpio_init(void)
-+{
-+	return platform_driver_register(&ar2315_gpio_driver);
-+}
-+subsys_initcall(ar2315_gpio_init);
---- a/arch/mips/ath25/devices.h
-+++ b/arch/mips/ath25/devices.h
-@@ -3,6 +3,11 @@
- 
- #include <linux/cpu.h>
- 
-+#define AR231X_GPIO_IRQ_BASE		0x30
-+
-+/* GPIO number for AR2315/16 reset issue workaround */
-+#define AR2315_RESET_GPIO		5
-+
- #define ATH25_REG_MS(_val, _field)	(((_val) & _field##_M) >> _field##_S)
- 
- #define ATH25_IRQ_CPU_CLOCK	(MIPS_CPU_IRQ_BASE + 7)	/* C0_CAUSE: 0x8000 */
---- a/arch/mips/ath25/ar2315_regs.h
-+++ b/arch/mips/ath25/ar2315_regs.h
-@@ -315,6 +315,9 @@
- #define AR2315_MEM_CFG_BANKADDR_BITS_M	0x00000018
- #define AR2315_MEM_CFG_BANKADDR_BITS_S	3
- 
-+/* GPIO MMR base address */
-+#define AR2315_GPIO			0x0088
-+
- /*
-  * Local Bus Interface Registers
-  */
diff --git a/target/linux/ath25/patches-3.18/110-ar2313_ethernet.patch b/target/linux/ath25/patches-3.18/110-ar2313_ethernet.patch
deleted file mode 100644
index bef70dd..0000000
--- a/target/linux/ath25/patches-3.18/110-ar2313_ethernet.patch
+++ /dev/null
@@ -1,1828 +0,0 @@
---- a/drivers/net/ethernet/atheros/Makefile
-+++ b/drivers/net/ethernet/atheros/Makefile
-@@ -7,3 +7,4 @@ obj-$(CONFIG_ATL2) += atlx/
- obj-$(CONFIG_ATL1E) += atl1e/
- obj-$(CONFIG_ATL1C) += atl1c/
- obj-$(CONFIG_ALX) += alx/
-+obj-$(CONFIG_NET_AR231X) += ar231x/
---- a/drivers/net/ethernet/atheros/Kconfig
-+++ b/drivers/net/ethernet/atheros/Kconfig
-@@ -5,7 +5,7 @@
- config NET_VENDOR_ATHEROS
- 	bool "Atheros devices"
- 	default y
--	depends on PCI
-+	depends on (PCI || ATH25)
- 	---help---
- 	  If you have a network (Ethernet) card belonging to this class, say Y
- 	  and read the Ethernet-HOWTO, available from
-@@ -80,4 +80,10 @@ config ALX
- 	  To compile this driver as a module, choose M here.  The module
- 	  will be called alx.
- 
-+config NET_AR231X
-+	tristate "Atheros AR231X built-in Ethernet support"
-+	depends on ATH25
-+	help
-+	  Support for the AR231x/531x ethernet controller
-+
- endif # NET_VENDOR_ATHEROS
---- /dev/null
-+++ b/drivers/net/ethernet/atheros/ar231x/Makefile
-@@ -0,0 +1 @@
-+obj-$(CONFIG_NET_AR231X) += ar231x.o
---- /dev/null
-+++ b/drivers/net/ethernet/atheros/ar231x/ar231x.c
-@@ -0,0 +1,1206 @@
-+/*
-+ * ar231x.c: Linux driver for the Atheros AR231x Ethernet device.
-+ *
-+ * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
-+ *
-+ * Thanks to Atheros for providing hardware and documentation
-+ * enabling me to write this driver.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * Additional credits:
-+ * This code is taken from John Taylor's Sibyte driver and then
-+ * modified for the AR2313.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/types.h>
-+#include <linux/errno.h>
-+#include <linux/ioport.h>
-+#include <linux/netdevice.h>
-+#include <linux/etherdevice.h>
-+#include <linux/interrupt.h>
-+#include <linux/skbuff.h>
-+#include <linux/init.h>
-+#include <linux/delay.h>
-+#include <linux/mm.h>
-+#include <linux/mii.h>
-+#include <linux/phy.h>
-+#include <linux/platform_device.h>
-+#include <linux/io.h>
-+
-+#define AR2313_MTU                     1692
-+#define AR2313_PRIOS                   1
-+#define AR2313_QUEUES                  (2*AR2313_PRIOS)
-+#define AR2313_DESCR_ENTRIES           64
-+
-+#ifndef min
-+#define min(a, b)	(((a) < (b)) ? (a) : (b))
-+#endif
-+
-+#ifndef SMP_CACHE_BYTES
-+#define SMP_CACHE_BYTES	L1_CACHE_BYTES
-+#endif
-+
-+#define AR2313_MBOX_SET_BIT  0x8
-+
-+#include "ar231x.h"
-+
-+/**
-+ * New interrupt handler strategy:
-+ *
-+ * An old interrupt handler worked using the traditional method of
-+ * replacing an skbuff with a new one when a packet arrives. However
-+ * the rx rings do not need to contain a static number of buffer
-+ * descriptors, thus it makes sense to move the memory allocation out
-+ * of the main interrupt handler and do it in a bottom half handler
-+ * and only allocate new buffers when the number of buffers in the
-+ * ring is below a certain threshold. In order to avoid starving the
-+ * NIC under heavy load it is however necessary to force allocation
-+ * when hitting a minimum threshold. The strategy for alloction is as
-+ * follows:
-+ *
-+ *     RX_LOW_BUF_THRES    - allocate buffers in the bottom half
-+ *     RX_PANIC_LOW_THRES  - we are very low on buffers, allocate
-+ *                           the buffers in the interrupt handler
-+ *     RX_RING_THRES       - maximum number of buffers in the rx ring
-+ *
-+ * One advantagous side effect of this allocation approach is that the
-+ * entire rx processing can be done without holding any spin lock
-+ * since the rx rings and registers are totally independent of the tx
-+ * ring and its registers.  This of course includes the kmalloc's of
-+ * new skb's. Thus start_xmit can run in parallel with rx processing
-+ * and the memory allocation on SMP systems.
-+ *
-+ * Note that running the skb reallocation in a bottom half opens up
-+ * another can of races which needs to be handled properly. In
-+ * particular it can happen that the interrupt handler tries to run
-+ * the reallocation while the bottom half is either running on another
-+ * CPU or was interrupted on the same CPU. To get around this the
-+ * driver uses bitops to prevent the reallocation routines from being
-+ * reentered.
-+ *
-+ * TX handling can also be done without holding any spin lock, wheee
-+ * this is fun! since tx_csm is only written to by the interrupt
-+ * handler.
-+ */
-+
-+/**
-+ * Threshold values for RX buffer allocation - the low water marks for
-+ * when to start refilling the rings are set to 75% of the ring
-+ * sizes. It seems to make sense to refill the rings entirely from the
-+ * intrrupt handler once it gets below the panic threshold, that way
-+ * we don't risk that the refilling is moved to another CPU when the
-+ * one running the interrupt handler just got the slab code hot in its
-+ * cache.
-+ */
-+#define RX_RING_SIZE		AR2313_DESCR_ENTRIES
-+#define RX_PANIC_THRES	        (RX_RING_SIZE/4)
-+#define RX_LOW_THRES	        ((3*RX_RING_SIZE)/4)
-+#define CRC_LEN                 4
-+#define RX_OFFSET               2
-+
-+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
-+#define VLAN_HDR                4
-+#else
-+#define VLAN_HDR                0
-+#endif
-+
-+#define AR2313_BUFSIZE		(AR2313_MTU + VLAN_HDR + ETH_HLEN + CRC_LEN + \
-+				 RX_OFFSET)
-+
-+#ifdef MODULE
-+MODULE_LICENSE("GPL");
-+MODULE_AUTHOR("Sameer Dekate <sdekate@arubanetworks.com>, Imre Kaloz <kaloz@openwrt.org>, Felix Fietkau <nbd@openwrt.org>");
-+MODULE_DESCRIPTION("AR231x Ethernet driver");
-+#endif
-+
-+#define virt_to_phys(x) ((u32)(x) & 0x1fffffff)
-+
-+/* prototypes */
-+static void ar231x_halt(struct net_device *dev);
-+static void rx_tasklet_func(unsigned long data);
-+static void rx_tasklet_cleanup(struct net_device *dev);
-+static void ar231x_multicast_list(struct net_device *dev);
-+static void ar231x_tx_timeout(struct net_device *dev);
-+
-+static int ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum);
-+static int ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
-+				u16 value);
-+static int ar231x_mdiobus_reset(struct mii_bus *bus);
-+static int ar231x_mdiobus_probe(struct net_device *dev);
-+static void ar231x_adjust_link(struct net_device *dev);
-+
-+#ifndef ERR
-+#define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args)
-+#endif
-+
-+#ifdef CONFIG_NET_POLL_CONTROLLER
-+static void
-+ar231x_netpoll(struct net_device *dev)
-+{
-+	unsigned long flags;
-+
-+	local_irq_save(flags);
-+	ar231x_interrupt(dev->irq, dev);
-+	local_irq_restore(flags);
-+}
-+#endif
-+
-+static const struct net_device_ops ar231x_ops = {
-+	.ndo_open		= ar231x_open,
-+	.ndo_stop		= ar231x_close,
-+	.ndo_start_xmit		= ar231x_start_xmit,
-+	.ndo_set_rx_mode	= ar231x_multicast_list,
-+	.ndo_do_ioctl		= ar231x_ioctl,
-+	.ndo_change_mtu		= eth_change_mtu,
-+	.ndo_validate_addr	= eth_validate_addr,
-+	.ndo_set_mac_address	= eth_mac_addr,
-+	.ndo_tx_timeout		= ar231x_tx_timeout,
-+#ifdef CONFIG_NET_POLL_CONTROLLER
-+	.ndo_poll_controller	= ar231x_netpoll,
-+#endif
-+};
-+
-+static int ar231x_probe(struct platform_device *pdev)
-+{
-+	struct net_device *dev;
-+	struct ar231x_private *sp;
-+	struct resource *res;
-+	unsigned long ar_eth_base;
-+	char buf[64];
-+
-+	dev = alloc_etherdev(sizeof(struct ar231x_private));
-+
-+	if (dev == NULL) {
-+		printk(KERN_ERR
-+			   "ar231x: Unable to allocate net_device structure!\n");
-+		return -ENOMEM;
-+	}
-+
-+	platform_set_drvdata(pdev, dev);
-+
-+	sp = netdev_priv(dev);
-+	sp->dev = dev;
-+	sp->cfg = pdev->dev.platform_data;
-+
-+	sprintf(buf, "eth%d_membase", pdev->id);
-+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, buf);
-+	if (!res)
-+		return -ENODEV;
-+
-+	sp->link = 0;
-+	ar_eth_base = res->start;
-+
-+	sprintf(buf, "eth%d_irq", pdev->id);
-+	dev->irq = platform_get_irq_byname(pdev, buf);
-+
-+	spin_lock_init(&sp->lock);
-+
-+	dev->features |= NETIF_F_HIGHDMA;
-+	dev->netdev_ops = &ar231x_ops;
-+
-+	tasklet_init(&sp->rx_tasklet, rx_tasklet_func, (unsigned long)dev);
-+	tasklet_disable(&sp->rx_tasklet);
-+
-+	sp->eth_regs = ioremap_nocache(ar_eth_base, sizeof(*sp->eth_regs));
-+	if (!sp->eth_regs) {
-+		printk("Can't remap eth registers\n");
-+		return -ENXIO;
-+	}
-+
-+	/**
-+	 * When there's only one MAC, PHY regs are typically on ENET0,
-+	 * even though the MAC might be on ENET1.
-+	 * So remap PHY regs separately.
-+	 */
-+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "eth0_mii");
-+	if (!res) {
-+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-+						   "eth1_mii");
-+		if (!res)
-+			return -ENODEV;
-+	}
-+	sp->phy_regs = ioremap_nocache(res->start, resource_size(res));
-+	if (!sp->phy_regs) {
-+		printk("Can't remap phy registers\n");
-+		return -ENXIO;
-+	}
-+
-+	sp->dma_regs = ioremap_nocache(ar_eth_base + 0x1000,
-+				       sizeof(*sp->dma_regs));
-+	if (!sp->dma_regs) {
-+		printk("Can't remap DMA registers\n");
-+		return -ENXIO;
-+	}
-+	dev->base_addr = ar_eth_base + 0x1000;
-+
-+	strncpy(sp->name, "Atheros AR231x", sizeof(sp->name) - 1);
-+	sp->name[sizeof(sp->name) - 1] = '\0';
-+	memcpy(dev->dev_addr, sp->cfg->macaddr, 6);
-+
-+	if (ar231x_init(dev)) {
-+		/* ar231x_init() calls ar231x_init_cleanup() on error */
-+		kfree(dev);
-+		return -ENODEV;
-+	}
-+
-+	if (register_netdev(dev)) {
-+		printk("%s: register_netdev failed\n", __func__);
-+		return -1;
-+	}
-+
-+	printk("%s: %s: %pM, irq %d\n", dev->name, sp->name, dev->dev_addr,
-+	       dev->irq);
-+
-+	sp->mii_bus = mdiobus_alloc();
-+	if (sp->mii_bus == NULL)
-+		return -1;
-+
-+	sp->mii_bus->priv = dev;
-+	sp->mii_bus->read = ar231x_mdiobus_read;
-+	sp->mii_bus->write = ar231x_mdiobus_write;
-+	sp->mii_bus->reset = ar231x_mdiobus_reset;
-+	sp->mii_bus->name = "ar231x_eth_mii";
-+	snprintf(sp->mii_bus->id, MII_BUS_ID_SIZE, "%d", pdev->id);
-+	sp->mii_bus->irq = kmalloc(sizeof(int), GFP_KERNEL);
-+	*sp->mii_bus->irq = PHY_POLL;
-+
-+	mdiobus_register(sp->mii_bus);
-+
-+	if (ar231x_mdiobus_probe(dev) != 0) {
-+		printk(KERN_ERR "%s: mdiobus_probe failed\n", dev->name);
-+		rx_tasklet_cleanup(dev);
-+		ar231x_init_cleanup(dev);
-+		unregister_netdev(dev);
-+		kfree(dev);
-+		return -ENODEV;
-+	}
-+
-+	/* start link poll timer */
-+	ar231x_setup_timer(dev);
-+
-+	return 0;
-+}
-+
-+static void ar231x_multicast_list(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	unsigned int filter;
-+
-+	filter = sp->eth_regs->mac_control;
-+
-+	if (dev->flags & IFF_PROMISC)
-+		filter |= MAC_CONTROL_PR;
-+	else
-+		filter &= ~MAC_CONTROL_PR;
-+	if ((dev->flags & IFF_ALLMULTI) || (netdev_mc_count(dev) > 0))
-+		filter |= MAC_CONTROL_PM;
-+	else
-+		filter &= ~MAC_CONTROL_PM;
-+
-+	sp->eth_regs->mac_control = filter;
-+}
-+
-+static void rx_tasklet_cleanup(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+
-+	/**
-+	 * Tasklet may be scheduled. Need to get it removed from the list
-+	 * since we're about to free the struct.
-+	 */
-+
-+	sp->unloading = 1;
-+	tasklet_enable(&sp->rx_tasklet);
-+	tasklet_kill(&sp->rx_tasklet);
-+}
-+
-+static int ar231x_remove(struct platform_device *pdev)
-+{
-+	struct net_device *dev = platform_get_drvdata(pdev);
-+	struct ar231x_private *sp = netdev_priv(dev);
-+
-+	rx_tasklet_cleanup(dev);
-+	ar231x_init_cleanup(dev);
-+	unregister_netdev(dev);
-+	mdiobus_unregister(sp->mii_bus);
-+	mdiobus_free(sp->mii_bus);
-+	kfree(dev);
-+	return 0;
-+}
-+
-+/**
-+ * Restart the AR2313 ethernet controller.
-+ */
-+static int ar231x_restart(struct net_device *dev)
-+{
-+	/* disable interrupts */
-+	disable_irq(dev->irq);
-+
-+	/* stop mac */
-+	ar231x_halt(dev);
-+
-+	/* initialize */
-+	ar231x_init(dev);
-+
-+	/* enable interrupts */
-+	enable_irq(dev->irq);
-+
-+	return 0;
-+}
-+
-+static struct platform_driver ar231x_driver = {
-+	.driver.name = "ar231x-eth",
-+	.probe = ar231x_probe,
-+	.remove = ar231x_remove,
-+};
-+
-+module_platform_driver(ar231x_driver);
-+
-+static void ar231x_free_descriptors(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+
-+	if (sp->rx_ring != NULL) {
-+		kfree((void *)KSEG0ADDR(sp->rx_ring));
-+		sp->rx_ring = NULL;
-+		sp->tx_ring = NULL;
-+	}
-+}
-+
-+static int ar231x_allocate_descriptors(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	int size;
-+	int j;
-+	ar231x_descr_t *space;
-+
-+	if (sp->rx_ring != NULL) {
-+		printk("%s: already done.\n", __func__);
-+		return 0;
-+	}
-+
-+	size = sizeof(ar231x_descr_t) * (AR2313_DESCR_ENTRIES * AR2313_QUEUES);
-+	space = kmalloc(size, GFP_KERNEL);
-+	if (space == NULL)
-+		return 1;
-+
-+	/* invalidate caches */
-+	dma_cache_inv((unsigned int)space, size);
-+
-+	/* now convert pointer to KSEG1 */
-+	space = (ar231x_descr_t *)KSEG1ADDR(space);
-+
-+	memset((void *)space, 0, size);
-+
-+	sp->rx_ring = space;
-+	space += AR2313_DESCR_ENTRIES;
-+
-+	sp->tx_ring = space;
-+	space += AR2313_DESCR_ENTRIES;
-+
-+	/* Initialize the transmit Descriptors */
-+	for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
-+		ar231x_descr_t *td = &sp->tx_ring[j];
-+
-+		td->status = 0;
-+		td->devcs = DMA_TX1_CHAINED;
-+		td->addr = 0;
-+		td->descr = virt_to_phys(&sp->tx_ring[DSC_NEXT(j)]);
-+	}
-+
-+	return 0;
-+}
-+
-+/**
-+ * Generic cleanup handling data allocated during init. Used when the
-+ * module is unloaded or if an error occurs during initialization
-+ */
-+static void ar231x_init_cleanup(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	struct sk_buff *skb;
-+	int j;
-+
-+	ar231x_free_descriptors(dev);
-+
-+	if (sp->eth_regs)
-+		iounmap((void *)sp->eth_regs);
-+	if (sp->dma_regs)
-+		iounmap((void *)sp->dma_regs);
-+	if (sp->phy_regs)
-+		iounmap((void *)sp->phy_regs);
-+
-+	if (sp->rx_skb) {
-+		for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
-+			skb = sp->rx_skb[j];
-+			if (skb) {
-+				sp->rx_skb[j] = NULL;
-+				dev_kfree_skb(skb);
-+			}
-+		}
-+		kfree(sp->rx_skb);
-+		sp->rx_skb = NULL;
-+	}
-+
-+	if (sp->tx_skb) {
-+		for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
-+			skb = sp->tx_skb[j];
-+			if (skb) {
-+				sp->tx_skb[j] = NULL;
-+				dev_kfree_skb(skb);
-+			}
-+		}
-+		kfree(sp->tx_skb);
-+		sp->tx_skb = NULL;
-+	}
-+}
-+
-+static int ar231x_setup_timer(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+
-+	init_timer(&sp->link_timer);
-+
-+	sp->link_timer.function = ar231x_link_timer_fn;
-+	sp->link_timer.data = (int)dev;
-+	sp->link_timer.expires = jiffies + HZ;
-+
-+	add_timer(&sp->link_timer);
-+	return 0;
-+}
-+
-+static void ar231x_link_timer_fn(unsigned long data)
-+{
-+	struct net_device *dev = (struct net_device *)data;
-+	struct ar231x_private *sp = netdev_priv(dev);
-+
-+	/**
-+	 * See if the link status changed.
-+	 * This was needed to make sure we set the PHY to the
-+	 * autonegotiated value of half or full duplex.
-+	 */
-+	ar231x_check_link(dev);
-+
-+	/**
-+	 * Loop faster when we don't have link.
-+	 * This was needed to speed up the AP bootstrap time.
-+	 */
-+	if (sp->link == 0)
-+		mod_timer(&sp->link_timer, jiffies + HZ / 2);
-+	else
-+		mod_timer(&sp->link_timer, jiffies + LINK_TIMER);
-+}
-+
-+static void ar231x_check_link(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	u16 phy_data;
-+
-+	phy_data = ar231x_mdiobus_read(sp->mii_bus, sp->phy, MII_BMSR);
-+	if (sp->phy_data != phy_data) {
-+		if (phy_data & BMSR_LSTATUS) {
-+			/**
-+			 * Link is present, ready link partner ability to
-+			 * deterine duplexity.
-+			 */
-+			int duplex = 0;
-+			u16 reg;
-+
-+			sp->link = 1;
-+			reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy,
-+						  MII_BMCR);
-+			if (reg & BMCR_ANENABLE) {
-+				/* auto neg enabled */
-+				reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy,
-+							  MII_LPA);
-+				duplex = reg & (LPA_100FULL | LPA_10FULL) ?
-+					 1 : 0;
-+			} else {
-+				/* no auto neg, just read duplex config */
-+				duplex = (reg & BMCR_FULLDPLX) ? 1 : 0;
-+			}
-+
-+			printk(KERN_INFO "%s: Configuring MAC for %s duplex\n",
-+			       dev->name, (duplex) ? "full" : "half");
-+
-+			if (duplex) {
-+				/* full duplex */
-+				sp->eth_regs->mac_control =
-+					(sp->eth_regs->mac_control |
-+					 MAC_CONTROL_F) & ~MAC_CONTROL_DRO;
-+			} else {
-+				/* half duplex */
-+				sp->eth_regs->mac_control =
-+					(sp->eth_regs->mac_control |
-+					 MAC_CONTROL_DRO) & ~MAC_CONTROL_F;
-+			}
-+		} else {
-+			/* no link */
-+			sp->link = 0;
-+		}
-+		sp->phy_data = phy_data;
-+	}
-+}
-+
-+static int ar231x_reset_reg(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	unsigned int ethsal, ethsah;
-+	unsigned int flags;
-+
-+	sp->cfg->reset_set(sp->cfg->reset_mac);
-+	mdelay(10);
-+	sp->cfg->reset_clear(sp->cfg->reset_mac);
-+	mdelay(10);
-+	sp->cfg->reset_set(sp->cfg->reset_phy);
-+	mdelay(10);
-+	sp->cfg->reset_clear(sp->cfg->reset_phy);
-+	mdelay(10);
-+
-+	sp->dma_regs->bus_mode = (DMA_BUS_MODE_SWR);
-+	mdelay(10);
-+	sp->dma_regs->bus_mode =
-+		((32 << DMA_BUS_MODE_PBL_SHIFT) | DMA_BUS_MODE_BLE);
-+
-+	/* enable interrupts */
-+	sp->dma_regs->intr_ena = DMA_STATUS_AIS | DMA_STATUS_NIS |
-+				 DMA_STATUS_RI | DMA_STATUS_TI |
-+				 DMA_STATUS_FBE;
-+	sp->dma_regs->xmt_base = virt_to_phys(sp->tx_ring);
-+	sp->dma_regs->rcv_base = virt_to_phys(sp->rx_ring);
-+	sp->dma_regs->control =
-+		(DMA_CONTROL_SR | DMA_CONTROL_ST | DMA_CONTROL_SF);
-+
-+	sp->eth_regs->flow_control = (FLOW_CONTROL_FCE);
-+	sp->eth_regs->vlan_tag = (0x8100);
-+
-+	/* Enable Ethernet Interface */
-+	flags = (MAC_CONTROL_TE |	/* transmit enable */
-+			 MAC_CONTROL_PM |	/* pass mcast */
-+			 MAC_CONTROL_F |	/* full duplex */
-+			 MAC_CONTROL_HBD);	/* heart beat disabled */
-+
-+	if (dev->flags & IFF_PROMISC) {	/* set promiscuous mode */
-+		flags |= MAC_CONTROL_PR;
-+	}
-+	sp->eth_regs->mac_control = flags;
-+
-+	/* Set all Ethernet station address registers to their initial values */
-+	ethsah = (((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
-+		 (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF);
-+
-+	ethsal = (((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
-+		 (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
-+		 (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
-+		 (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF);
-+
-+	sp->eth_regs->mac_addr[0] = ethsah;
-+	sp->eth_regs->mac_addr[1] = ethsal;
-+
-+	mdelay(10);
-+
-+	return 0;
-+}
-+
-+static int ar231x_init(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	int ecode = 0;
-+
-+	/* Allocate descriptors */
-+	if (ar231x_allocate_descriptors(dev)) {
-+		printk("%s: %s: ar231x_allocate_descriptors failed\n",
-+		       dev->name, __func__);
-+		ecode = -EAGAIN;
-+		goto init_error;
-+	}
-+
-+	/* Get the memory for the skb rings */
-+	if (sp->rx_skb == NULL) {
-+		sp->rx_skb =
-+			kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
-+				GFP_KERNEL);
-+		if (!(sp->rx_skb)) {
-+			printk("%s: %s: rx_skb kmalloc failed\n",
-+			       dev->name, __func__);
-+			ecode = -EAGAIN;
-+			goto init_error;
-+		}
-+	}
-+	memset(sp->rx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
-+
-+	if (sp->tx_skb == NULL) {
-+		sp->tx_skb =
-+			kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
-+				GFP_KERNEL);
-+		if (!(sp->tx_skb)) {
-+			printk("%s: %s: tx_skb kmalloc failed\n",
-+			       dev->name, __func__);
-+			ecode = -EAGAIN;
-+			goto init_error;
-+		}
-+	}
-+	memset(sp->tx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
-+
-+	/**
-+	 * Set tx_csm before we start receiving interrupts, otherwise
-+	 * the interrupt handler might think it is supposed to process
-+	 * tx ints before we are up and running, which may cause a null
-+	 * pointer access in the int handler.
-+	 */
-+	sp->rx_skbprd = 0;
-+	sp->cur_rx = 0;
-+	sp->tx_prd = 0;
-+	sp->tx_csm = 0;
-+
-+	/* Zero the stats before starting the interface */
-+	memset(&dev->stats, 0, sizeof(dev->stats));
-+
-+	/**
-+	 * We load the ring here as there seem to be no way to tell the
-+	 * firmware to wipe the ring without re-initializing it.
-+	 */
-+	ar231x_load_rx_ring(dev, RX_RING_SIZE);
-+
-+	/* Init hardware */
-+	ar231x_reset_reg(dev);
-+
-+	/* Get the IRQ */
-+	ecode = request_irq(dev->irq, &ar231x_interrupt, IRQF_DISABLED,
-+			    dev->name, dev);
-+	if (ecode) {
-+		printk(KERN_WARNING "%s: %s: Requested IRQ %d is busy\n",
-+		       dev->name, __func__, dev->irq);
-+		goto init_error;
-+	}
-+
-+	tasklet_enable(&sp->rx_tasklet);
-+
-+	return 0;
-+
-+init_error:
-+	ar231x_init_cleanup(dev);
-+	return ecode;
-+}
-+
-+/**
-+ * Load the rx ring.
-+ *
-+ * Loading rings is safe without holding the spin lock since this is
-+ * done only before the device is enabled, thus no interrupts are
-+ * generated and by the interrupt handler/tasklet handler.
-+ */
-+static void ar231x_load_rx_ring(struct net_device *dev, int nr_bufs)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	short i, idx;
-+
-+	idx = sp->rx_skbprd;
-+
-+	for (i = 0; i < nr_bufs; i++) {
-+		struct sk_buff *skb;
-+		ar231x_descr_t *rd;
-+
-+		if (sp->rx_skb[idx])
-+			break;
-+
-+		skb = netdev_alloc_skb_ip_align(dev, AR2313_BUFSIZE);
-+		if (!skb) {
-+			printk("\n\n\n\n %s: No memory in system\n\n\n\n",
-+			       __func__);
-+			break;
-+		}
-+
-+		/* Make sure IP header starts on a fresh cache line */
-+		skb->dev = dev;
-+		sp->rx_skb[idx] = skb;
-+
-+		rd = (ar231x_descr_t *)&sp->rx_ring[idx];
-+
-+		/* initialize dma descriptor */
-+		rd->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
-+					 DMA_RX1_CHAINED);
-+		rd->addr = virt_to_phys(skb->data);
-+		rd->descr = virt_to_phys(&sp->rx_ring[DSC_NEXT(idx)]);
-+		rd->status = DMA_RX_OWN;
-+
-+		idx = DSC_NEXT(idx);
-+	}
-+
-+	if (i)
-+		sp->rx_skbprd = idx;
-+}
-+
-+#define AR2313_MAX_PKTS_PER_CALL        64
-+
-+static int ar231x_rx_int(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	struct sk_buff *skb, *skb_new;
-+	ar231x_descr_t *rxdesc;
-+	unsigned int status;
-+	u32 idx;
-+	int pkts = 0;
-+	int rval;
-+
-+	idx = sp->cur_rx;
-+
-+	/* process at most the entire ring and then wait for another int */
-+	while (1) {
-+		rxdesc = &sp->rx_ring[idx];
-+		status = rxdesc->status;
-+
-+		if (status & DMA_RX_OWN) {
-+			/* SiByte owns descriptor or descr not yet filled in */
-+			rval = 0;
-+			break;
-+		}
-+
-+		if (++pkts > AR2313_MAX_PKTS_PER_CALL) {
-+			rval = 1;
-+			break;
-+		}
-+
-+		if ((status & DMA_RX_ERROR) && !(status & DMA_RX_LONG)) {
-+			dev->stats.rx_errors++;
-+			dev->stats.rx_dropped++;
-+
-+			/* add statistics counters */
-+			if (status & DMA_RX_ERR_CRC)
-+				dev->stats.rx_crc_errors++;
-+			if (status & DMA_RX_ERR_COL)
-+				dev->stats.rx_over_errors++;
-+			if (status & DMA_RX_ERR_LENGTH)
-+				dev->stats.rx_length_errors++;
-+			if (status & DMA_RX_ERR_RUNT)
-+				dev->stats.rx_over_errors++;
-+			if (status & DMA_RX_ERR_DESC)
-+				dev->stats.rx_over_errors++;
-+
-+		} else {
-+			/* alloc new buffer. */
-+			skb_new = netdev_alloc_skb_ip_align(dev,
-+							    AR2313_BUFSIZE);
-+			if (skb_new != NULL) {
-+				skb = sp->rx_skb[idx];
-+				/* set skb */
-+				skb_put(skb, ((status >> DMA_RX_LEN_SHIFT) &
-+					0x3fff) - CRC_LEN);
-+
-+				dev->stats.rx_bytes += skb->len;
-+				skb->protocol = eth_type_trans(skb, dev);
-+				/* pass the packet to upper layers */
-+				netif_rx(skb);
-+
-+				skb_new->dev = dev;
-+				/* reset descriptor's curr_addr */
-+				rxdesc->addr = virt_to_phys(skb_new->data);
-+
-+				dev->stats.rx_packets++;
-+				sp->rx_skb[idx] = skb_new;
-+			} else {
-+				dev->stats.rx_dropped++;
-+			}
-+		}
-+
-+		rxdesc->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
-+						 DMA_RX1_CHAINED);
-+		rxdesc->status = DMA_RX_OWN;
-+
-+		idx = DSC_NEXT(idx);
-+	}
-+
-+	sp->cur_rx = idx;
-+
-+	return rval;
-+}
-+
-+static void ar231x_tx_int(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	u32 idx;
-+	struct sk_buff *skb;
-+	ar231x_descr_t *txdesc;
-+	unsigned int status = 0;
-+
-+	idx = sp->tx_csm;
-+
-+	while (idx != sp->tx_prd) {
-+		txdesc = &sp->tx_ring[idx];
-+		status = txdesc->status;
-+
-+		if (status & DMA_TX_OWN) {
-+			/* ar231x dma still owns descr */
-+			break;
-+		}
-+		/* done with this descriptor */
-+		dma_unmap_single(NULL, txdesc->addr,
-+				 txdesc->devcs & DMA_TX1_BSIZE_MASK,
-+				 DMA_TO_DEVICE);
-+		txdesc->status = 0;
-+
-+		if (status & DMA_TX_ERROR) {
-+			dev->stats.tx_errors++;
-+			dev->stats.tx_dropped++;
-+			if (status & DMA_TX_ERR_UNDER)
-+				dev->stats.tx_fifo_errors++;
-+			if (status & DMA_TX_ERR_HB)
-+				dev->stats.tx_heartbeat_errors++;
-+			if (status & (DMA_TX_ERR_LOSS | DMA_TX_ERR_LINK))
-+				dev->stats.tx_carrier_errors++;
-+			if (status & (DMA_TX_ERR_LATE | DMA_TX_ERR_COL |
-+			    DMA_TX_ERR_JABBER | DMA_TX_ERR_DEFER))
-+				dev->stats.tx_aborted_errors++;
-+		} else {
-+			/* transmit OK */
-+			dev->stats.tx_packets++;
-+		}
-+
-+		skb = sp->tx_skb[idx];
-+		sp->tx_skb[idx] = NULL;
-+		idx = DSC_NEXT(idx);
-+		dev->stats.tx_bytes += skb->len;
-+		dev_kfree_skb_irq(skb);
-+	}
-+
-+	sp->tx_csm = idx;
-+}
-+
-+static void rx_tasklet_func(unsigned long data)
-+{
-+	struct net_device *dev = (struct net_device *)data;
-+	struct ar231x_private *sp = netdev_priv(dev);
-+
-+	if (sp->unloading)
-+		return;
-+
-+	if (ar231x_rx_int(dev)) {
-+		tasklet_hi_schedule(&sp->rx_tasklet);
-+	} else {
-+		unsigned long flags;
-+
-+		spin_lock_irqsave(&sp->lock, flags);
-+		sp->dma_regs->intr_ena |= DMA_STATUS_RI;
-+		spin_unlock_irqrestore(&sp->lock, flags);
-+	}
-+}
-+
-+static void rx_schedule(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+
-+	sp->dma_regs->intr_ena &= ~DMA_STATUS_RI;
-+
-+	tasklet_hi_schedule(&sp->rx_tasklet);
-+}
-+
-+static irqreturn_t ar231x_interrupt(int irq, void *dev_id)
-+{
-+	struct net_device *dev = (struct net_device *)dev_id;
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	unsigned int status, enabled;
-+
-+	/* clear interrupt */
-+	/* Don't clear RI bit if currently disabled */
-+	status = sp->dma_regs->status;
-+	enabled = sp->dma_regs->intr_ena;
-+	sp->dma_regs->status = status & enabled;
-+
-+	if (status & DMA_STATUS_NIS) {
-+		/* normal status */
-+		/**
-+		 * Don't schedule rx processing if interrupt
-+		 * is already disabled.
-+		 */
-+		if (status & enabled & DMA_STATUS_RI) {
-+			/* receive interrupt */
-+			rx_schedule(dev);
-+		}
-+		if (status & DMA_STATUS_TI) {
-+			/* transmit interrupt */
-+			ar231x_tx_int(dev);
-+		}
-+	}
-+
-+	/* abnormal status */
-+	if (status & (DMA_STATUS_FBE | DMA_STATUS_TPS))
-+		ar231x_restart(dev);
-+
-+	return IRQ_HANDLED;
-+}
-+
-+static int ar231x_open(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	unsigned int ethsal, ethsah;
-+
-+	/* reset the hardware, in case the MAC address changed */
-+	ethsah = (((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
-+		 (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF);
-+
-+	ethsal = (((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
-+		 (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
-+		 (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
-+		 (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF);
-+
-+	sp->eth_regs->mac_addr[0] = ethsah;
-+	sp->eth_regs->mac_addr[1] = ethsal;
-+
-+	mdelay(10);
-+
-+	dev->mtu = 1500;
-+	netif_start_queue(dev);
-+
-+	sp->eth_regs->mac_control |= MAC_CONTROL_RE;
-+
-+	return 0;
-+}
-+
-+static void ar231x_tx_timeout(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	unsigned long flags;
-+
-+	spin_lock_irqsave(&sp->lock, flags);
-+	ar231x_restart(dev);
-+	spin_unlock_irqrestore(&sp->lock, flags);
-+}
-+
-+static void ar231x_halt(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	int j;
-+
-+	tasklet_disable(&sp->rx_tasklet);
-+
-+	/* kill the MAC */
-+	sp->eth_regs->mac_control &= ~(MAC_CONTROL_RE |	/* disable Receives */
-+				       MAC_CONTROL_TE);	/* disable Transmits */
-+	/* stop dma */
-+	sp->dma_regs->control = 0;
-+	sp->dma_regs->bus_mode = DMA_BUS_MODE_SWR;
-+
-+	/* place phy and MAC in reset */
-+	sp->cfg->reset_set(sp->cfg->reset_mac);
-+	sp->cfg->reset_set(sp->cfg->reset_phy);
-+
-+	/* free buffers on tx ring */
-+	for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
-+		struct sk_buff *skb;
-+		ar231x_descr_t *txdesc;
-+
-+		txdesc = &sp->tx_ring[j];
-+		txdesc->descr = 0;
-+
-+		skb = sp->tx_skb[j];
-+		if (skb) {
-+			dev_kfree_skb(skb);
-+			sp->tx_skb[j] = NULL;
-+		}
-+	}
-+}
-+
-+/**
-+ * close should do nothing. Here's why. It's called when
-+ * 'ifconfig bond0 down' is run. If it calls free_irq then
-+ * the irq is gone forever ! When bond0 is made 'up' again,
-+ * the ar231x_open () does not call request_irq (). Worse,
-+ * the call to ar231x_halt() generates a WDOG reset due to
-+ * the write to reset register and the box reboots.
-+ * Commenting this out is good since it allows the
-+ * system to resume when bond0 is made up again.
-+ */
-+static int ar231x_close(struct net_device *dev)
-+{
-+#if 0
-+	/* Disable interrupts */
-+	disable_irq(dev->irq);
-+
-+	/**
-+	 * Without (or before) releasing irq and stopping hardware, this
-+	 * is an absolute non-sense, by the way. It will be reset instantly
-+	 * by the first irq.
-+	 */
-+	netif_stop_queue(dev);
-+
-+	/* stop the MAC and DMA engines */
-+	ar231x_halt(dev);
-+
-+	/* release the interrupt */
-+	free_irq(dev->irq, dev);
-+
-+#endif
-+	return 0;
-+}
-+
-+static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	ar231x_descr_t *td;
-+	u32 idx;
-+
-+	idx = sp->tx_prd;
-+	td = &sp->tx_ring[idx];
-+
-+	if (td->status & DMA_TX_OWN) {
-+		/* free skbuf and lie to the caller that we sent it out */
-+		dev->stats.tx_dropped++;
-+		dev_kfree_skb(skb);
-+
-+		/* restart transmitter in case locked */
-+		sp->dma_regs->xmt_poll = 0;
-+		return 0;
-+	}
-+
-+	/* Setup the transmit descriptor. */
-+	td->devcs = ((skb->len << DMA_TX1_BSIZE_SHIFT) |
-+				 (DMA_TX1_LS | DMA_TX1_IC | DMA_TX1_CHAINED));
-+	td->addr = dma_map_single(NULL, skb->data, skb->len, DMA_TO_DEVICE);
-+	td->status = DMA_TX_OWN;
-+
-+	/* kick transmitter last */
-+	sp->dma_regs->xmt_poll = 0;
-+
-+	sp->tx_skb[idx] = skb;
-+	idx = DSC_NEXT(idx);
-+	sp->tx_prd = idx;
-+
-+	return 0;
-+}
-+
-+static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+
-+	switch (cmd) {
-+	case SIOCGMIIPHY:
-+	case SIOCGMIIREG:
-+	case SIOCSMIIREG:
-+		return phy_mii_ioctl(sp->phy_dev, ifr, cmd);
-+
-+	default:
-+		break;
-+	}
-+
-+	return -EOPNOTSUPP;
-+}
-+
-+static void ar231x_adjust_link(struct net_device *dev)
-+{
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	unsigned int mc;
-+
-+	if (!sp->phy_dev->link)
-+		return;
-+
-+	if (sp->phy_dev->duplex != sp->oldduplex) {
-+		mc = readl(&sp->eth_regs->mac_control);
-+		mc &= ~(MAC_CONTROL_F | MAC_CONTROL_DRO);
-+		if (sp->phy_dev->duplex)
-+			mc |= MAC_CONTROL_F;
-+		else
-+			mc |= MAC_CONTROL_DRO;
-+		writel(mc, &sp->eth_regs->mac_control);
-+		sp->oldduplex = sp->phy_dev->duplex;
-+	}
-+}
-+
-+#define MII_ADDR(phy, reg) \
-+	((reg << MII_ADDR_REG_SHIFT) | (phy << MII_ADDR_PHY_SHIFT))
-+
-+static int
-+ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
-+{
-+	struct net_device *const dev = bus->priv;
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	volatile MII *ethernet = sp->phy_regs;
-+
-+	ethernet->mii_addr = MII_ADDR(phy_addr, regnum);
-+	while (ethernet->mii_addr & MII_ADDR_BUSY)
-+		;
-+	return ethernet->mii_data >> MII_DATA_SHIFT;
-+}
-+
-+static int
-+ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, u16 value)
-+{
-+	struct net_device *const dev = bus->priv;
-+	struct ar231x_private *sp = netdev_priv(dev);
-+	volatile MII *ethernet = sp->phy_regs;
-+
-+	while (ethernet->mii_addr & MII_ADDR_BUSY)
-+		;
-+	ethernet->mii_data = value << MII_DATA_SHIFT;
-+	ethernet->mii_addr = MII_ADDR(phy_addr, regnum) | MII_ADDR_WRITE;
-+
-+	return 0;
-+}
-+
-+static int ar231x_mdiobus_reset(struct mii_bus *bus)
-+{
-+	struct net_device *const dev = bus->priv;
-+
-+	ar231x_reset_reg(dev);
-+
-+	return 0;
-+}
-+
-+static int ar231x_mdiobus_probe(struct net_device *dev)
-+{
-+	struct ar231x_private *const sp = netdev_priv(dev);
-+	struct phy_device *phydev = NULL;
-+	int phy_addr;
-+
-+	/* find the first (lowest address) PHY on the current MAC's MII bus */
-+	for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++)
-+		if (sp->mii_bus->phy_map[phy_addr]) {
-+			phydev = sp->mii_bus->phy_map[phy_addr];
-+			sp->phy = phy_addr;
-+			break; /* break out with first one found */
-+		}
-+
-+	if (!phydev) {
-+		printk(KERN_ERR "ar231x: %s: no PHY found\n", dev->name);
-+		return -1;
-+	}
-+
-+	/* now we are supposed to have a proper phydev, to attach to... */
-+	BUG_ON(!phydev);
-+	BUG_ON(phydev->attached_dev);
-+
-+	phydev = phy_connect(dev, dev_name(&phydev->dev), &ar231x_adjust_link,
-+			     PHY_INTERFACE_MODE_MII);
-+
-+	if (IS_ERR(phydev)) {
-+		printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
-+		return PTR_ERR(phydev);
-+	}
-+
-+	/* mask with MAC supported features */
-+	phydev->supported &= (SUPPORTED_10baseT_Half
-+		| SUPPORTED_10baseT_Full
-+		| SUPPORTED_100baseT_Half
-+		| SUPPORTED_100baseT_Full
-+		| SUPPORTED_Autoneg
-+		/* | SUPPORTED_Pause | SUPPORTED_Asym_Pause */
-+		| SUPPORTED_MII
-+		| SUPPORTED_TP);
-+
-+	phydev->advertising = phydev->supported;
-+
-+	sp->oldduplex = -1;
-+	sp->phy_dev = phydev;
-+
-+	printk(KERN_INFO "%s: attached PHY driver [%s] (mii_bus:phy_addr=%s)\n",
-+	       dev->name, phydev->drv->name, dev_name(&phydev->dev));
-+
-+	return 0;
-+}
-+
---- /dev/null
-+++ b/drivers/net/ethernet/atheros/ar231x/ar231x.h
-@@ -0,0 +1,288 @@
-+/*
-+ * ar231x.h: Linux driver for the Atheros AR231x Ethernet device.
-+ *
-+ * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
-+ *
-+ * Thanks to Atheros for providing hardware and documentation
-+ * enabling me to write this driver.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ */
-+
-+#ifndef _AR2313_H_
-+#define _AR2313_H_
-+
-+#include <linux/interrupt.h>
-+#include <generated/autoconf.h>
-+#include <linux/bitops.h>
-+#include <ath25_platform.h>
-+
-+/* probe link timer - 5 secs */
-+#define LINK_TIMER    (5*HZ)
-+
-+#define IS_DMA_TX_INT(X)   (((X) & (DMA_STATUS_TI)) != 0)
-+#define IS_DMA_RX_INT(X)   (((X) & (DMA_STATUS_RI)) != 0)
-+#define IS_DRIVER_OWNED(X) (((X) & (DMA_TX_OWN))    == 0)
-+
-+#define AR2313_TX_TIMEOUT (HZ/4)
-+
-+/* Rings */
-+#define DSC_RING_ENTRIES_SIZE	(AR2313_DESCR_ENTRIES * sizeof(struct desc))
-+#define DSC_NEXT(idx)	        ((idx + 1) & (AR2313_DESCR_ENTRIES - 1))
-+
-+#define AR2313_MBGET		2
-+#define AR2313_MBSET		3
-+#define AR2313_PCI_RECONFIG	4
-+#define AR2313_PCI_DUMP		5
-+#define AR2313_TEST_PANIC	6
-+#define AR2313_TEST_NULLPTR	7
-+#define AR2313_READ_DATA	8
-+#define AR2313_WRITE_DATA	9
-+#define AR2313_GET_VERSION	10
-+#define AR2313_TEST_HANG	11
-+#define AR2313_SYNC		12
-+
-+#define DMA_RX_ERR_CRC		BIT(1)
-+#define DMA_RX_ERR_DRIB		BIT(2)
-+#define DMA_RX_ERR_MII		BIT(3)
-+#define DMA_RX_EV2		BIT(5)
-+#define DMA_RX_ERR_COL		BIT(6)
-+#define DMA_RX_LONG		BIT(7)
-+#define DMA_RX_LS		BIT(8)	/* last descriptor */
-+#define DMA_RX_FS		BIT(9)	/* first descriptor */
-+#define DMA_RX_MF		BIT(10)	/* multicast frame */
-+#define DMA_RX_ERR_RUNT		BIT(11)	/* runt frame */
-+#define DMA_RX_ERR_LENGTH	BIT(12)	/* length error */
-+#define DMA_RX_ERR_DESC		BIT(14)	/* descriptor error */
-+#define DMA_RX_ERROR		BIT(15)	/* error summary */
-+#define DMA_RX_LEN_MASK		0x3fff0000
-+#define DMA_RX_LEN_SHIFT	16
-+#define DMA_RX_FILT		BIT(30)
-+#define DMA_RX_OWN		BIT(31)	/* desc owned by DMA controller */
-+
-+#define DMA_RX1_BSIZE_MASK	0x000007ff
-+#define DMA_RX1_BSIZE_SHIFT	0
-+#define DMA_RX1_CHAINED		BIT(24)
-+#define DMA_RX1_RER		BIT(25)
-+
-+#define DMA_TX_ERR_UNDER	BIT(1)	/* underflow error */
-+#define DMA_TX_ERR_DEFER	BIT(2)	/* excessive deferral */
-+#define DMA_TX_COL_MASK		0x78
-+#define DMA_TX_COL_SHIFT	3
-+#define DMA_TX_ERR_HB		BIT(7)	/* hearbeat failure */
-+#define DMA_TX_ERR_COL		BIT(8)	/* excessive collisions */
-+#define DMA_TX_ERR_LATE		BIT(9)	/* late collision */
-+#define DMA_TX_ERR_LINK		BIT(10)	/* no carrier */
-+#define DMA_TX_ERR_LOSS		BIT(11)	/* loss of carrier */
-+#define DMA_TX_ERR_JABBER	BIT(14)	/* transmit jabber timeout */
-+#define DMA_TX_ERROR		BIT(15)	/* frame aborted */
-+#define DMA_TX_OWN		BIT(31)	/* descr owned by DMA controller */
-+
-+#define DMA_TX1_BSIZE_MASK	0x000007ff
-+#define DMA_TX1_BSIZE_SHIFT	0
-+#define DMA_TX1_CHAINED		BIT(24)	/* chained descriptors */
-+#define DMA_TX1_TER		BIT(25)	/* transmit end of ring */
-+#define DMA_TX1_FS		BIT(29)	/* first segment */
-+#define DMA_TX1_LS		BIT(30)	/* last segment */
-+#define DMA_TX1_IC		BIT(31)	/* interrupt on completion */
-+
-+#define RCVPKT_LENGTH(X)	(X  >> 16)	/* Received pkt Length */
-+
-+#define MAC_CONTROL_RE		BIT(2)	/* receive enable */
-+#define MAC_CONTROL_TE		BIT(3)	/* transmit enable */
-+#define MAC_CONTROL_DC		BIT(5)	/* Deferral check */
-+#define MAC_CONTROL_ASTP	BIT(8)	/* Auto pad strip */
-+#define MAC_CONTROL_DRTY	BIT(10)	/* Disable retry */
-+#define MAC_CONTROL_DBF		BIT(11)	/* Disable bcast frames */
-+#define MAC_CONTROL_LCC		BIT(12)	/* late collision ctrl */
-+#define MAC_CONTROL_HP		BIT(13)	/* Hash Perfect filtering */
-+#define MAC_CONTROL_HASH	BIT(14)	/* Unicast hash filtering */
-+#define MAC_CONTROL_HO		BIT(15)	/* Hash only filtering */
-+#define MAC_CONTROL_PB		BIT(16)	/* Pass Bad frames */
-+#define MAC_CONTROL_IF		BIT(17)	/* Inverse filtering */
-+#define MAC_CONTROL_PR		BIT(18)	/* promis mode (valid frames only) */
-+#define MAC_CONTROL_PM		BIT(19)	/* pass multicast */
-+#define MAC_CONTROL_F		BIT(20)	/* full-duplex */
-+#define MAC_CONTROL_DRO		BIT(23)	/* Disable Receive Own */
-+#define MAC_CONTROL_HBD		BIT(28)	/* heart-beat disabled (MUST BE SET) */
-+#define MAC_CONTROL_BLE		BIT(30)	/* big endian mode */
-+#define MAC_CONTROL_RA		BIT(31)	/* rcv all (valid and invalid frames) */
-+
-+#define MII_ADDR_BUSY		BIT(0)
-+#define MII_ADDR_WRITE		BIT(1)
-+#define MII_ADDR_REG_SHIFT	6
-+#define MII_ADDR_PHY_SHIFT	11
-+#define MII_DATA_SHIFT		0
-+
-+#define FLOW_CONTROL_FCE	BIT(1)
-+
-+#define DMA_BUS_MODE_SWR	BIT(0)	/* software reset */
-+#define DMA_BUS_MODE_BLE	BIT(7)	/* big endian mode */
-+#define DMA_BUS_MODE_PBL_SHIFT	8	/* programmable burst length 32 */
-+#define DMA_BUS_MODE_DBO	BIT(20)	/* big-endian descriptors */
-+
-+#define DMA_STATUS_TI		BIT(0)	/* transmit interrupt */
-+#define DMA_STATUS_TPS		BIT(1)	/* transmit process stopped */
-+#define DMA_STATUS_TU		BIT(2)	/* transmit buffer unavailable */
-+#define DMA_STATUS_TJT		BIT(3)	/* transmit buffer timeout */
-+#define DMA_STATUS_UNF		BIT(5)	/* transmit underflow */
-+#define DMA_STATUS_RI		BIT(6)	/* receive interrupt */
-+#define DMA_STATUS_RU		BIT(7)	/* receive buffer unavailable */
-+#define DMA_STATUS_RPS		BIT(8)	/* receive process stopped */
-+#define DMA_STATUS_ETI		BIT(10)	/* early transmit interrupt */
-+#define DMA_STATUS_FBE		BIT(13)	/* fatal bus interrupt */
-+#define DMA_STATUS_ERI		BIT(14)	/* early receive interrupt */
-+#define DMA_STATUS_AIS		BIT(15)	/* abnormal interrupt summary */
-+#define DMA_STATUS_NIS		BIT(16)	/* normal interrupt summary */
-+#define DMA_STATUS_RS_SHIFT	17	/* receive process state */
-+#define DMA_STATUS_TS_SHIFT	20	/* transmit process state */
-+#define DMA_STATUS_EB_SHIFT	23	/* error bits */
-+
-+#define DMA_CONTROL_SR		BIT(1)	/* start receive */
-+#define DMA_CONTROL_ST		BIT(13)	/* start transmit */
-+#define DMA_CONTROL_SF		BIT(21)	/* store and forward */
-+
-+typedef struct {
-+	volatile unsigned int status;	/* OWN, Device control and status. */
-+	volatile unsigned int devcs;	/* pkt Control bits + Length */
-+	volatile unsigned int addr;	/* Current Address. */
-+	volatile unsigned int descr;	/* Next descriptor in chain. */
-+} ar231x_descr_t;
-+
-+/**
-+ * New Combo structure for Both Eth0 AND eth1
-+ *
-+ * Don't directly access MII related regs since phy chip could be actually
-+ * connected to another ethernet block.
-+ */
-+typedef struct {
-+	volatile unsigned int mac_control;	/* 0x00 */
-+	volatile unsigned int mac_addr[2];	/* 0x04 - 0x08 */
-+	volatile unsigned int mcast_table[2];	/* 0x0c - 0x10 */
-+	volatile unsigned int __mii_addr;	/* 0x14 */
-+	volatile unsigned int __mii_data;	/* 0x18 */
-+	volatile unsigned int flow_control;	/* 0x1c */
-+	volatile unsigned int vlan_tag;	/* 0x20 */
-+	volatile unsigned int pad[7];	/* 0x24 - 0x3c */
-+	volatile unsigned int ucast_table[8];	/* 0x40-0x5c */
-+} ETHERNET_STRUCT;
-+
-+typedef struct {
-+	volatile unsigned int mii_addr;
-+	volatile unsigned int mii_data;
-+} MII;
-+
-+/********************************************************************
-+ * Interrupt controller
-+ ********************************************************************/
-+
-+typedef struct {
-+	volatile unsigned int wdog_control;	/* 0x08 */
-+	volatile unsigned int wdog_timer;	/* 0x0c */
-+	volatile unsigned int misc_status;	/* 0x10 */
-+	volatile unsigned int misc_mask;	/* 0x14 */
-+	volatile unsigned int global_status;	/* 0x18 */
-+	volatile unsigned int reserved;	/* 0x1c */
-+	volatile unsigned int reset_control;	/* 0x20 */
-+} INTERRUPT;
-+
-+/********************************************************************
-+ * DMA controller
-+ ********************************************************************/
-+typedef struct {
-+	volatile unsigned int bus_mode;	/* 0x00 (CSR0) */
-+	volatile unsigned int xmt_poll;	/* 0x04 (CSR1) */
-+	volatile unsigned int rcv_poll;	/* 0x08 (CSR2) */
-+	volatile unsigned int rcv_base;	/* 0x0c (CSR3) */
-+	volatile unsigned int xmt_base;	/* 0x10 (CSR4) */
-+	volatile unsigned int status;	/* 0x14 (CSR5) */
-+	volatile unsigned int control;	/* 0x18 (CSR6) */
-+	volatile unsigned int intr_ena;	/* 0x1c (CSR7) */
-+	volatile unsigned int rcv_missed;	/* 0x20 (CSR8) */
-+	volatile unsigned int reserved[11];	/* 0x24-0x4c (CSR9-19) */
-+	volatile unsigned int cur_tx_buf_addr;	/* 0x50 (CSR20) */
-+	volatile unsigned int cur_rx_buf_addr;	/* 0x50 (CSR21) */
-+} DMA;
-+
-+/**
-+ * Struct private for the Sibyte.
-+ *
-+ * Elements are grouped so variables used by the tx handling goes
-+ * together, and will go into the same cache lines etc. in order to
-+ * avoid cache line contention between the rx and tx handling on SMP.
-+ *
-+ * Frequently accessed variables are put at the beginning of the
-+ * struct to help the compiler generate better/shorter code.
-+ */
-+struct ar231x_private {
-+	struct net_device *dev;
-+	int version;
-+	u32 mb[2];
-+
-+	volatile MII *phy_regs;
-+	volatile ETHERNET_STRUCT *eth_regs;
-+	volatile DMA *dma_regs;
-+	struct ar231x_eth *cfg;
-+
-+	spinlock_t lock;			/* Serialise access to device */
-+
-+	/* RX and TX descriptors, must be adjacent */
-+	ar231x_descr_t *rx_ring;
-+	ar231x_descr_t *tx_ring;
-+
-+	struct sk_buff **rx_skb;
-+	struct sk_buff **tx_skb;
-+
-+	/* RX elements */
-+	u32 rx_skbprd;
-+	u32 cur_rx;
-+
-+	/* TX elements */
-+	u32 tx_prd;
-+	u32 tx_csm;
-+
-+	/* Misc elements */
-+	char name[48];
-+	struct {
-+		u32 address;
-+		u32 length;
-+		char *mapping;
-+	} desc;
-+
-+	struct timer_list link_timer;
-+	unsigned short phy;		/* merlot phy = 1, samsung phy = 0x1f */
-+	unsigned short mac;
-+	unsigned short link;		/* 0 - link down, 1 - link up */
-+	u16 phy_data;
-+
-+	struct tasklet_struct rx_tasklet;
-+	int unloading;
-+
-+	struct phy_device *phy_dev;
-+	struct mii_bus *mii_bus;
-+	int oldduplex;
-+};
-+
-+/* Prototypes */
-+static int ar231x_init(struct net_device *dev);
-+#ifdef TX_TIMEOUT
-+static void ar231x_tx_timeout(struct net_device *dev);
-+#endif
-+static int ar231x_restart(struct net_device *dev);
-+static void ar231x_load_rx_ring(struct net_device *dev, int bufs);
-+static irqreturn_t ar231x_interrupt(int irq, void *dev_id);
-+static int ar231x_open(struct net_device *dev);
-+static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev);
-+static int ar231x_close(struct net_device *dev);
-+static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd);
-+static void ar231x_init_cleanup(struct net_device *dev);
-+static int ar231x_setup_timer(struct net_device *dev);
-+static void ar231x_link_timer_fn(unsigned long data);
-+static void ar231x_check_link(struct net_device *dev);
-+
-+#endif	/* _AR2313_H_ */
---- a/arch/mips/ath25/ar2315_regs.h
-+++ b/arch/mips/ath25/ar2315_regs.h
-@@ -57,6 +57,9 @@
- #define AR2315_PCI_EXT_BASE	0x80000000	/* PCI external */
- #define AR2315_PCI_EXT_SIZE	0x40000000
- 
-+/* MII registers offset inside Ethernet MMR region */
-+#define AR2315_ENET0_MII_BASE	(AR2315_ENET0_BASE + 0x14)
-+
- /*
-  * Configuration registers
-  */
---- a/arch/mips/ath25/ar5312_regs.h
-+++ b/arch/mips/ath25/ar5312_regs.h
-@@ -64,6 +64,10 @@
- #define AR5312_AR5312_REV7	0x0057		/* AR5312 WMAC (AP30-040) */
- #define AR5312_AR2313_REV8	0x0058		/* AR2313 WMAC (AP43-030) */
- 
-+/* MII registers offset inside Ethernet MMR region */
-+#define AR5312_ENET0_MII_BASE	(AR5312_ENET0_BASE + 0x14)
-+#define AR5312_ENET1_MII_BASE	(AR5312_ENET1_BASE + 0x14)
-+
- /* Reset/Timer Block Address Map */
- #define AR5312_TIMER		0x0000 /* countdown timer */
- #define AR5312_RELOAD		0x0004 /* timer reload value */
---- a/arch/mips/ath25/ar2315.c
-+++ b/arch/mips/ath25/ar2315.c
-@@ -136,6 +136,8 @@ static void ar2315_irq_dispatch(void)
- 
- 	if (pending & CAUSEF_IP3)
- 		do_IRQ(AR2315_IRQ_WLAN0);
-+	else if (pending & CAUSEF_IP4)
-+		do_IRQ(AR2315_IRQ_ENET0);
- #ifdef CONFIG_PCI_AR2315
- 	else if (pending & CAUSEF_IP5)
- 		do_IRQ(AR2315_IRQ_LCBUS_PCI);
-@@ -169,6 +171,29 @@ void __init ar2315_arch_init_irq(void)
- 	ar2315_misc_irq_domain = domain;
- }
- 
-+static void ar2315_device_reset_set(u32 mask)
-+{
-+	u32 val;
-+
-+	val = ar2315_rst_reg_read(AR2315_RESET);
-+	ar2315_rst_reg_write(AR2315_RESET, val | mask);
-+}
-+
-+static void ar2315_device_reset_clear(u32 mask)
-+{
-+	u32 val;
-+
-+	val = ar2315_rst_reg_read(AR2315_RESET);
-+	ar2315_rst_reg_write(AR2315_RESET, val & ~mask);
-+}
-+
-+static struct ar231x_eth ar2315_eth_data = {
-+	.reset_set = ar2315_device_reset_set,
-+	.reset_clear = ar2315_device_reset_clear,
-+	.reset_mac = AR2315_RESET_ENET0,
-+	.reset_phy = AR2315_RESET_EPHY0,
-+};
-+
- static struct resource ar2315_gpio_res[] = {
- 	{
- 		.name = "ar2315-gpio",
-@@ -205,6 +230,11 @@ void __init ar2315_init_devices(void)
- 	ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
- 	platform_device_register(&ar2315_gpio);
- 
-+	ar2315_eth_data.macaddr = ath25_board.config->enet0_mac;
-+	ath25_add_ethernet(0, AR2315_ENET0_BASE, "eth0_mii",
-+			   AR2315_ENET0_MII_BASE, AR2315_IRQ_ENET0,
-+			   &ar2315_eth_data);
-+
- 	ath25_add_wmac(0, AR2315_WLAN0_BASE, AR2315_IRQ_WLAN0);
- }
- 
---- a/arch/mips/ath25/ar5312.c
-+++ b/arch/mips/ath25/ar5312.c
-@@ -132,6 +132,10 @@ static void ar5312_irq_dispatch(void)
- 
- 	if (pending & CAUSEF_IP2)
- 		do_IRQ(AR5312_IRQ_WLAN0);
-+	else if (pending & CAUSEF_IP3)
-+		do_IRQ(AR5312_IRQ_ENET0);
-+	else if (pending & CAUSEF_IP4)
-+		do_IRQ(AR5312_IRQ_ENET1);
- 	else if (pending & CAUSEF_IP5)
- 		do_IRQ(AR5312_IRQ_WLAN1);
- 	else if (pending & CAUSEF_IP6)
-@@ -163,6 +167,36 @@ void __init ar5312_arch_init_irq(void)
- 	ar5312_misc_irq_domain = domain;
- }
- 
-+static void ar5312_device_reset_set(u32 mask)
-+{
-+	u32 val;
-+
-+	val = ar5312_rst_reg_read(AR5312_RESET);
-+	ar5312_rst_reg_write(AR5312_RESET, val | mask);
-+}
-+
-+static void ar5312_device_reset_clear(u32 mask)
-+{
-+	u32 val;
-+
-+	val = ar5312_rst_reg_read(AR5312_RESET);
-+	ar5312_rst_reg_write(AR5312_RESET, val & ~mask);
-+}
-+
-+static struct ar231x_eth ar5312_eth0_data = {
-+	.reset_set = ar5312_device_reset_set,
-+	.reset_clear = ar5312_device_reset_clear,
-+	.reset_mac = AR5312_RESET_ENET0,
-+	.reset_phy = AR5312_RESET_EPHY0,
-+};
-+
-+static struct ar231x_eth ar5312_eth1_data = {
-+	.reset_set = ar5312_device_reset_set,
-+	.reset_clear = ar5312_device_reset_clear,
-+	.reset_mac = AR5312_RESET_ENET1,
-+	.reset_phy = AR5312_RESET_EPHY1,
-+};
-+
- static struct physmap_flash_data ar5312_flash_data = {
- 	.width = 2,
- };
-@@ -243,6 +277,7 @@ static void __init ar5312_flash_init(voi
- void __init ar5312_init_devices(void)
- {
- 	struct ath25_boarddata *config;
-+	u8 *c;
- 
- 	ar5312_flash_init();
- 
-@@ -266,8 +301,30 @@ void __init ar5312_init_devices(void)
- 
- 	platform_device_register(&ar5312_gpio);
- 
-+	/* Fix up MAC addresses if necessary */
-+	if (is_broadcast_ether_addr(config->enet0_mac))
-+		ether_addr_copy(config->enet0_mac, config->enet1_mac);
-+
-+	/* If ENET0 and ENET1 have the same mac address,
-+	 * increment the one from ENET1 */
-+	if (ether_addr_equal(config->enet0_mac, config->enet1_mac)) {
-+		c = config->enet1_mac + 5;
-+		while ((c >= config->enet1_mac) && !(++(*c)))
-+			c--;
-+	}
-+
- 	switch (ath25_soc) {
- 	case ATH25_SOC_AR5312:
-+		ar5312_eth0_data.macaddr = config->enet0_mac;
-+		ath25_add_ethernet(0, AR5312_ENET0_BASE, "eth0_mii",
-+				   AR5312_ENET0_MII_BASE, AR5312_IRQ_ENET0,
-+				   &ar5312_eth0_data);
-+
-+		ar5312_eth1_data.macaddr = config->enet1_mac;
-+		ath25_add_ethernet(1, AR5312_ENET1_BASE, "eth1_mii",
-+				   AR5312_ENET1_MII_BASE, AR5312_IRQ_ENET1,
-+				   &ar5312_eth1_data);
-+
- 		if (!ath25_board.radio)
- 			return;
- 
-@@ -276,8 +333,18 @@ void __init ar5312_init_devices(void)
- 
- 		ath25_add_wmac(0, AR5312_WLAN0_BASE, AR5312_IRQ_WLAN0);
- 		break;
-+	/*
-+	 * AR2312/3 ethernet uses the PHY of ENET0, but the MAC
-+	 * of ENET1. Atheros calls it 'twisted' for a reason :)
-+	 */
- 	case ATH25_SOC_AR2312:
- 	case ATH25_SOC_AR2313:
-+		ar5312_eth1_data.reset_phy = ar5312_eth0_data.reset_phy;
-+		ar5312_eth1_data.macaddr = config->enet0_mac;
-+		ath25_add_ethernet(1, AR5312_ENET1_BASE, "eth0_mii",
-+				   AR5312_ENET0_MII_BASE, AR5312_IRQ_ENET1,
-+				   &ar5312_eth1_data);
-+
- 		if (!ath25_board.radio)
- 			return;
- 		break;
---- a/arch/mips/ath25/devices.h
-+++ b/arch/mips/ath25/devices.h
-@@ -32,6 +32,8 @@ extern struct ar231x_board_config ath25_
- extern void (*ath25_irq_dispatch)(void);
- 
- int ath25_find_config(phys_addr_t offset, unsigned long size);
-+int ath25_add_ethernet(int nr, u32 base, const char *mii_name, u32 mii_base,
-+		       int irq, void *pdata);
- void ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk);
- int ath25_add_wmac(int nr, u32 base, int irq);
- 
---- a/arch/mips/ath25/devices.c
-+++ b/arch/mips/ath25/devices.c
-@@ -12,6 +12,51 @@
- struct ar231x_board_config ath25_board;
- enum ath25_soc_type ath25_soc = ATH25_SOC_UNKNOWN;
- 
-+static struct resource ath25_eth0_res[] = {
-+	{
-+		.name = "eth0_membase",
-+		.flags = IORESOURCE_MEM,
-+	},
-+	{
-+		.name = "eth0_mii",
-+		.flags = IORESOURCE_MEM,
-+	},
-+	{
-+		.name = "eth0_irq",
-+		.flags = IORESOURCE_IRQ,
-+	}
-+};
-+
-+static struct resource ath25_eth1_res[] = {
-+	{
-+		.name = "eth1_membase",
-+		.flags = IORESOURCE_MEM,
-+	},
-+	{
-+		.name = "eth1_mii",
-+		.flags = IORESOURCE_MEM,
-+	},
-+	{
-+		.name = "eth1_irq",
-+		.flags = IORESOURCE_IRQ,
-+	}
-+};
-+
-+static struct platform_device ath25_eth[] = {
-+	{
-+		.id = 0,
-+		.name = "ar231x-eth",
-+		.resource = ath25_eth0_res,
-+		.num_resources = ARRAY_SIZE(ath25_eth0_res)
-+	},
-+	{
-+		.id = 1,
-+		.name = "ar231x-eth",
-+		.resource = ath25_eth1_res,
-+		.num_resources = ARRAY_SIZE(ath25_eth1_res)
-+	}
-+};
-+
- static struct resource ath25_wmac0_res[] = {
- 	{
- 		.name = "wmac0_membase",
-@@ -70,6 +115,25 @@ const char *get_system_type(void)
- 	return soc_type_strings[ath25_soc];
- }
- 
-+int __init ath25_add_ethernet(int nr, u32 base, const char *mii_name,
-+			      u32 mii_base, int irq, void *pdata)
-+{
-+	struct resource *res;
-+
-+	ath25_eth[nr].dev.platform_data = pdata;
-+	res = &ath25_eth[nr].resource[0];
-+	res->start = base;
-+	res->end = base + 0x2000 - 1;
-+	res++;
-+	res->name = mii_name;
-+	res->start = mii_base;
-+	res->end = mii_base + 8 - 1;
-+	res++;
-+	res->start = irq;
-+	res->end = irq;
-+	return platform_device_register(&ath25_eth[nr]);
-+}
-+
- void __init ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk)
- {
- 	struct uart_port s;
---- a/arch/mips/include/asm/mach-ath25/ath25_platform.h
-+++ b/arch/mips/include/asm/mach-ath25/ath25_platform.h
-@@ -70,4 +70,15 @@ struct ar231x_board_config {
- 	const char *radio;
- };
- 
-+/*
-+ * Platform device information for the Ethernet MAC
-+ */
-+struct ar231x_eth {
-+	void (*reset_set)(u32);
-+	void (*reset_clear)(u32);
-+	u32 reset_mac;
-+	u32 reset_phy;
-+	char *macaddr;
-+};
-+
- #endif /* __ASM_MACH_ATH25_PLATFORM_H */
diff --git a/target/linux/ath25/patches-3.18/120-spiflash.patch b/target/linux/ath25/patches-3.18/120-spiflash.patch
deleted file mode 100644
index 7d88ee2..0000000
--- a/target/linux/ath25/patches-3.18/120-spiflash.patch
+++ /dev/null
@@ -1,634 +0,0 @@
---- a/drivers/mtd/devices/Kconfig
-+++ b/drivers/mtd/devices/Kconfig
-@@ -120,6 +120,10 @@ config MTD_BCM47XXSFLASH
- 	  registered by bcma as platform devices. This enables driver for
- 	  serial flash memories (only read-only mode is implemented).
- 
-+config MTD_AR2315
-+	tristate "Atheros AR2315+ SPI Flash support"
-+	depends on SOC_AR2315
-+
- config MTD_SLRAM
- 	tristate "Uncached system RAM"
- 	help
---- a/drivers/mtd/devices/Makefile
-+++ b/drivers/mtd/devices/Makefile
-@@ -14,6 +14,7 @@ obj-$(CONFIG_MTD_DATAFLASH)	+= mtd_dataf
- obj-$(CONFIG_MTD_M25P80)	+= m25p80.o
- obj-$(CONFIG_MTD_SPEAR_SMI)	+= spear_smi.o
- obj-$(CONFIG_MTD_SST25L)	+= sst25l.o
-+obj-$(CONFIG_MTD_AR2315)	+= ar2315.o
- obj-$(CONFIG_MTD_BCM47XXSFLASH)	+= bcm47xxsflash.o
- obj-$(CONFIG_MTD_ST_SPI_FSM)    += st_spi_fsm.o
- 
---- /dev/null
-+++ b/drivers/mtd/devices/ar2315.c
-@@ -0,0 +1,459 @@
-+
-+/*
-+ * MTD driver for the SPI Flash Memory support on Atheros AR2315
-+ *
-+ * Copyright (c) 2005-2006 Atheros Communications Inc.
-+ * Copyright (C) 2006-2007 FON Technology, SL.
-+ * Copyright (C) 2006-2007 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
-+ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
-+ *
-+ * This code is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/types.h>
-+#include <linux/errno.h>
-+#include <linux/slab.h>
-+#include <linux/mtd/mtd.h>
-+#include <linux/mtd/partitions.h>
-+#include <linux/platform_device.h>
-+#include <linux/sched.h>
-+#include <linux/delay.h>
-+#include <linux/io.h>
-+#include <linux/mutex.h>
-+
-+#include "ar2315_spiflash.h"
-+
-+#define DRIVER_NAME "ar2315-spiflash"
-+
-+#define busy_wait(_priv, _condition, _wait) do { \
-+	while (_condition) { \
-+		if (_wait > 1) \
-+			msleep(_wait); \
-+		else if ((_wait == 1) && need_resched()) \
-+			schedule(); \
-+		else \
-+			udelay(1); \
-+	} \
-+} while (0)
-+
-+enum {
-+	FLASH_NONE,
-+	FLASH_1MB,
-+	FLASH_2MB,
-+	FLASH_4MB,
-+	FLASH_8MB,
-+	FLASH_16MB,
-+};
-+
-+/* Flash configuration table */
-+struct flashconfig {
-+	u32 byte_cnt;
-+	u32 sector_cnt;
-+	u32 sector_size;
-+};
-+
-+static const struct flashconfig flashconfig_tbl[] = {
-+	[FLASH_NONE] = { 0, 0, 0},
-+	[FLASH_1MB]  = { STM_1MB_BYTE_COUNT, STM_1MB_SECTOR_COUNT,
-+			 STM_1MB_SECTOR_SIZE},
-+	[FLASH_2MB]  = { STM_2MB_BYTE_COUNT, STM_2MB_SECTOR_COUNT,
-+			 STM_2MB_SECTOR_SIZE},
-+	[FLASH_4MB]  = { STM_4MB_BYTE_COUNT, STM_4MB_SECTOR_COUNT,
-+			 STM_4MB_SECTOR_SIZE},
-+	[FLASH_8MB]  = { STM_8MB_BYTE_COUNT, STM_8MB_SECTOR_COUNT,
-+			 STM_8MB_SECTOR_SIZE},
-+	[FLASH_16MB] = { STM_16MB_BYTE_COUNT, STM_16MB_SECTOR_COUNT,
-+			 STM_16MB_SECTOR_SIZE}
-+};
-+
-+/* Mapping of generic opcodes to STM serial flash opcodes */
-+enum {
-+	SPI_WRITE_ENABLE,
-+	SPI_WRITE_DISABLE,
-+	SPI_RD_STATUS,
-+	SPI_WR_STATUS,
-+	SPI_RD_DATA,
-+	SPI_FAST_RD_DATA,
-+	SPI_PAGE_PROGRAM,
-+	SPI_SECTOR_ERASE,
-+	SPI_BULK_ERASE,
-+	SPI_DEEP_PWRDOWN,
-+	SPI_RD_SIG,
-+};
-+
-+struct opcodes {
-+	__u16 code;
-+	__s8 tx_cnt;
-+	__s8 rx_cnt;
-+};
-+
-+static const struct opcodes stm_opcodes[] = {
-+	[SPI_WRITE_ENABLE] = {STM_OP_WR_ENABLE, 1, 0},
-+	[SPI_WRITE_DISABLE] = {STM_OP_WR_DISABLE, 1, 0},
-+	[SPI_RD_STATUS] = {STM_OP_RD_STATUS, 1, 1},
-+	[SPI_WR_STATUS] = {STM_OP_WR_STATUS, 1, 0},
-+	[SPI_RD_DATA] = {STM_OP_RD_DATA, 4, 4},
-+	[SPI_FAST_RD_DATA] = {STM_OP_FAST_RD_DATA, 5, 0},
-+	[SPI_PAGE_PROGRAM] = {STM_OP_PAGE_PGRM, 8, 0},
-+	[SPI_SECTOR_ERASE] = {STM_OP_SECTOR_ERASE, 4, 0},
-+	[SPI_BULK_ERASE] = {STM_OP_BULK_ERASE, 1, 0},
-+	[SPI_DEEP_PWRDOWN] = {STM_OP_DEEP_PWRDOWN, 1, 0},
-+	[SPI_RD_SIG] = {STM_OP_RD_SIG, 4, 1},
-+};
-+
-+/* Driver private data structure */
-+struct spiflash_priv {
-+	struct mtd_info mtd;
-+	void __iomem *readaddr; /* memory mapped data for read  */
-+	void __iomem *mmraddr;  /* memory mapped register space */
-+	struct mutex lock;	/* serialize registers access */
-+};
-+
-+#define to_spiflash(_mtd) container_of(_mtd, struct spiflash_priv, mtd)
-+
-+enum {
-+	FL_READY,
-+	FL_READING,
-+	FL_ERASING,
-+	FL_WRITING
-+};
-+
-+/*****************************************************************************/
-+
-+static u32
-+spiflash_read_reg(struct spiflash_priv *priv, int reg)
-+{
-+	return ioread32(priv->mmraddr + reg);
-+}
-+
-+static void
-+spiflash_write_reg(struct spiflash_priv *priv, int reg, u32 data)
-+{
-+	iowrite32(data, priv->mmraddr + reg);
-+}
-+
-+static u32
-+spiflash_wait_busy(struct spiflash_priv *priv)
-+{
-+	u32 reg;
-+
-+	busy_wait(priv, (reg = spiflash_read_reg(priv, SPI_FLASH_CTL)) &
-+		SPI_CTL_BUSY, 0);
-+	return reg;
-+}
-+
-+static u32
-+spiflash_sendcmd(struct spiflash_priv *priv, int opcode, u32 addr)
-+{
-+	const struct opcodes *op;
-+	u32 reg, mask;
-+
-+	op = &stm_opcodes[opcode];
-+	reg = spiflash_wait_busy(priv);
-+	spiflash_write_reg(priv, SPI_FLASH_OPCODE,
-+			   ((u32)op->code) | (addr << 8));
-+
-+	reg &= ~SPI_CTL_TX_RX_CNT_MASK;
-+	reg |= SPI_CTL_START | op->tx_cnt | (op->rx_cnt << 4);
-+
-+	spiflash_write_reg(priv, SPI_FLASH_CTL, reg);
-+	spiflash_wait_busy(priv);
-+
-+	if (!op->rx_cnt)
-+		return 0;
-+
-+	reg = spiflash_read_reg(priv, SPI_FLASH_DATA);
-+
-+	switch (op->rx_cnt) {
-+	case 1:
-+		mask = 0x000000ff;
-+		break;
-+	case 2:
-+		mask = 0x0000ffff;
-+		break;
-+	case 3:
-+		mask = 0x00ffffff;
-+		break;
-+	default:
-+		mask = 0xffffffff;
-+		break;
-+	}
-+	reg &= mask;
-+
-+	return reg;
-+}
-+
-+/*
-+ * Probe SPI flash device
-+ * Function returns 0 for failure.
-+ * and flashconfig_tbl array index for success.
-+ */
-+static int
-+spiflash_probe_chip(struct platform_device *pdev, struct spiflash_priv *priv)
-+{
-+	u32 sig = spiflash_sendcmd(priv, SPI_RD_SIG, 0);
-+	int flash_size;
-+
-+	switch (sig) {
-+	case STM_8MBIT_SIGNATURE:
-+		flash_size = FLASH_1MB;
-+		break;
-+	case STM_16MBIT_SIGNATURE:
-+		flash_size = FLASH_2MB;
-+		break;
-+	case STM_32MBIT_SIGNATURE:
-+		flash_size = FLASH_4MB;
-+		break;
-+	case STM_64MBIT_SIGNATURE:
-+		flash_size = FLASH_8MB;
-+		break;
-+	case STM_128MBIT_SIGNATURE:
-+		flash_size = FLASH_16MB;
-+		break;
-+	default:
-+		dev_warn(&pdev->dev, "read of flash device signature failed!\n");
-+		return 0;
-+	}
-+
-+	return flash_size;
-+}
-+
-+static void
-+spiflash_wait_complete(struct spiflash_priv *priv, unsigned int timeout)
-+{
-+	busy_wait(priv, spiflash_sendcmd(priv, SPI_RD_STATUS, 0) &
-+		SPI_STATUS_WIP, timeout);
-+}
-+
-+static int
-+spiflash_erase(struct mtd_info *mtd, struct erase_info *instr)
-+{
-+	struct spiflash_priv *priv = to_spiflash(mtd);
-+	const struct opcodes *op;
-+	u32 temp, reg;
-+
-+	if (instr->addr + instr->len > mtd->size)
-+		return -EINVAL;
-+
-+	mutex_lock(&priv->lock);
-+
-+	spiflash_sendcmd(priv, SPI_WRITE_ENABLE, 0);
-+	reg = spiflash_wait_busy(priv);
-+
-+	op = &stm_opcodes[SPI_SECTOR_ERASE];
-+	temp = ((u32)instr->addr << 8) | (u32)(op->code);
-+	spiflash_write_reg(priv, SPI_FLASH_OPCODE, temp);
-+
-+	reg &= ~SPI_CTL_TX_RX_CNT_MASK;
-+	reg |= op->tx_cnt | SPI_CTL_START;
-+	spiflash_write_reg(priv, SPI_FLASH_CTL, reg);
-+
-+	spiflash_wait_complete(priv, 20);
-+
-+	mutex_unlock(&priv->lock);
-+
-+	instr->state = MTD_ERASE_DONE;
-+	mtd_erase_callback(instr);
-+
-+	return 0;
-+}
-+
-+static int
-+spiflash_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen,
-+	      u_char *buf)
-+{
-+	struct spiflash_priv *priv = to_spiflash(mtd);
-+
-+	if (!len)
-+		return 0;
-+
-+	if (from + len > mtd->size)
-+		return -EINVAL;
-+
-+	*retlen = len;
-+
-+	mutex_lock(&priv->lock);
-+
-+	memcpy_fromio(buf, priv->readaddr + from, len);
-+
-+	mutex_unlock(&priv->lock);
-+
-+	return 0;
-+}
-+
-+static int
-+spiflash_write(struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen,
-+	       const u8 *buf)
-+{
-+	struct spiflash_priv *priv = to_spiflash(mtd);
-+	u32 opcode, bytes_left;
-+
-+	*retlen = 0;
-+
-+	if (!len)
-+		return 0;
-+
-+	if (to + len > mtd->size)
-+		return -EINVAL;
-+
-+	bytes_left = len;
-+
-+	do {
-+		u32 read_len, reg, page_offset, spi_data = 0;
-+
-+		read_len = min(bytes_left, sizeof(u32));
-+
-+		/* 32-bit writes cannot span across a page boundary
-+		 * (256 bytes). This types of writes require two page
-+		 * program operations to handle it correctly. The STM part
-+		 * will write the overflow data to the beginning of the
-+		 * current page as opposed to the subsequent page.
-+		 */
-+		page_offset = (to & (STM_PAGE_SIZE - 1)) + read_len;
-+
-+		if (page_offset > STM_PAGE_SIZE)
-+			read_len -= (page_offset - STM_PAGE_SIZE);
-+
-+		mutex_lock(&priv->lock);
-+
-+		spiflash_sendcmd(priv, SPI_WRITE_ENABLE, 0);
-+		spi_data = 0;
-+		switch (read_len) {
-+		case 4:
-+			spi_data |= buf[3] << 24;
-+			/* fall through */
-+		case 3:
-+			spi_data |= buf[2] << 16;
-+			/* fall through */
-+		case 2:
-+			spi_data |= buf[1] << 8;
-+			/* fall through */
-+		case 1:
-+			spi_data |= buf[0] & 0xff;
-+			break;
-+		default:
-+			break;
-+		}
-+
-+		spiflash_write_reg(priv, SPI_FLASH_DATA, spi_data);
-+		opcode = stm_opcodes[SPI_PAGE_PROGRAM].code |
-+			(to & 0x00ffffff) << 8;
-+		spiflash_write_reg(priv, SPI_FLASH_OPCODE, opcode);
-+
-+		reg = spiflash_read_reg(priv, SPI_FLASH_CTL);
-+		reg &= ~SPI_CTL_TX_RX_CNT_MASK;
-+		reg |= (read_len + 4) | SPI_CTL_START;
-+		spiflash_write_reg(priv, SPI_FLASH_CTL, reg);
-+
-+		spiflash_wait_complete(priv, 1);
-+
-+		mutex_unlock(&priv->lock);
-+
-+		bytes_left -= read_len;
-+		to += read_len;
-+		buf += read_len;
-+
-+		*retlen += read_len;
-+	} while (bytes_left != 0);
-+
-+	return 0;
-+}
-+
-+#if defined CONFIG_MTD_REDBOOT_PARTS || CONFIG_MTD_MYLOADER_PARTS
-+static const char * const part_probe_types[] = {
-+	"cmdlinepart", "RedBoot", "MyLoader", NULL
-+};
-+#endif
-+
-+static int
-+spiflash_probe(struct platform_device *pdev)
-+{
-+	struct spiflash_priv *priv;
-+	struct mtd_info *mtd;
-+	struct resource *res;
-+	int index;
-+	int result = 0;
-+
-+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
-+	if (!priv)
-+		return -ENOMEM;
-+
-+	mutex_init(&priv->lock);
-+	mtd = &priv->mtd;
-+
-+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-+	priv->mmraddr = devm_ioremap_resource(&pdev->dev, res);
-+	if (IS_ERR(priv->mmraddr)) {
-+		dev_warn(&pdev->dev, "failed to map flash MMR\n");
-+		return PTR_ERR(priv->mmraddr);
-+	}
-+
-+	index = spiflash_probe_chip(pdev, priv);
-+	if (!index) {
-+		dev_warn(&pdev->dev, "found no flash device\n");
-+		return -ENODEV;
-+	}
-+
-+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+	priv->readaddr = devm_ioremap_resource(&pdev->dev, res);
-+	if (IS_ERR(priv->readaddr)) {
-+		dev_warn(&pdev->dev, "failed to map flash read mem\n");
-+		return PTR_ERR(priv->readaddr);
-+	}
-+
-+	platform_set_drvdata(pdev, priv);
-+	mtd->name = "spiflash";
-+	mtd->type = MTD_NORFLASH;
-+	mtd->flags = (MTD_CAP_NORFLASH|MTD_WRITEABLE);
-+	mtd->size = flashconfig_tbl[index].byte_cnt;
-+	mtd->erasesize = flashconfig_tbl[index].sector_size;
-+	mtd->writesize = 1;
-+	mtd->numeraseregions = 0;
-+	mtd->eraseregions = NULL;
-+	mtd->_erase = spiflash_erase;
-+	mtd->_read = spiflash_read;
-+	mtd->_write = spiflash_write;
-+	mtd->owner = THIS_MODULE;
-+
-+	dev_info(&pdev->dev, "%lld Kbytes flash detected\n", mtd->size >> 10);
-+
-+#if defined CONFIG_MTD_REDBOOT_PARTS || CONFIG_MTD_MYLOADER_PARTS
-+	/* parse redboot partitions */
-+
-+	result = mtd_device_parse_register(mtd, part_probe_types,
-+					   NULL, NULL, 0);
-+#endif
-+
-+	return result;
-+}
-+
-+static int
-+spiflash_remove(struct platform_device *pdev)
-+{
-+	struct spiflash_priv *priv = platform_get_drvdata(pdev);
-+
-+	mtd_device_unregister(&priv->mtd);
-+
-+	return 0;
-+}
-+
-+static struct platform_driver spiflash_driver = {
-+	.driver.name = DRIVER_NAME,
-+	.probe = spiflash_probe,
-+	.remove = spiflash_remove,
-+};
-+
-+module_platform_driver(spiflash_driver);
-+
-+MODULE_LICENSE("GPL");
-+MODULE_AUTHOR("OpenWrt.org");
-+MODULE_AUTHOR("Atheros Communications Inc");
-+MODULE_DESCRIPTION("MTD driver for SPI Flash on Atheros AR2315+ SOC");
-+MODULE_ALIAS("platform:" DRIVER_NAME);
-+
---- /dev/null
-+++ b/drivers/mtd/devices/ar2315_spiflash.h
-@@ -0,0 +1,106 @@
-+/*
-+ * Atheros AR2315 SPI Flash Memory support header file.
-+ *
-+ * Copyright (c) 2005, Atheros Communications Inc.
-+ * Copyright (C) 2006 FON Technology, SL.
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
-+ *
-+ * This code is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+ */
-+#ifndef __AR2315_SPIFLASH_H
-+#define __AR2315_SPIFLASH_H
-+
-+#define STM_PAGE_SIZE           256
-+
-+#define SFI_WRITE_BUFFER_SIZE   4
-+#define SFI_FLASH_ADDR_MASK     0x00ffffff
-+
-+#define STM_8MBIT_SIGNATURE     0x13
-+#define STM_M25P80_BYTE_COUNT   1048576
-+#define STM_M25P80_SECTOR_COUNT 16
-+#define STM_M25P80_SECTOR_SIZE  0x10000
-+
-+#define STM_16MBIT_SIGNATURE    0x14
-+#define STM_M25P16_BYTE_COUNT   2097152
-+#define STM_M25P16_SECTOR_COUNT 32
-+#define STM_M25P16_SECTOR_SIZE  0x10000
-+
-+#define STM_32MBIT_SIGNATURE    0x15
-+#define STM_M25P32_BYTE_COUNT   4194304
-+#define STM_M25P32_SECTOR_COUNT 64
-+#define STM_M25P32_SECTOR_SIZE  0x10000
-+
-+#define STM_64MBIT_SIGNATURE    0x16
-+#define STM_M25P64_BYTE_COUNT   8388608
-+#define STM_M25P64_SECTOR_COUNT 128
-+#define STM_M25P64_SECTOR_SIZE  0x10000
-+
-+#define STM_128MBIT_SIGNATURE   0x17
-+#define STM_M25P128_BYTE_COUNT   16777216
-+#define STM_M25P128_SECTOR_COUNT 256
-+#define STM_M25P128_SECTOR_SIZE  0x10000
-+
-+#define STM_1MB_BYTE_COUNT   STM_M25P80_BYTE_COUNT
-+#define STM_1MB_SECTOR_COUNT STM_M25P80_SECTOR_COUNT
-+#define STM_1MB_SECTOR_SIZE  STM_M25P80_SECTOR_SIZE
-+#define STM_2MB_BYTE_COUNT   STM_M25P16_BYTE_COUNT
-+#define STM_2MB_SECTOR_COUNT STM_M25P16_SECTOR_COUNT
-+#define STM_2MB_SECTOR_SIZE  STM_M25P16_SECTOR_SIZE
-+#define STM_4MB_BYTE_COUNT   STM_M25P32_BYTE_COUNT
-+#define STM_4MB_SECTOR_COUNT STM_M25P32_SECTOR_COUNT
-+#define STM_4MB_SECTOR_SIZE  STM_M25P32_SECTOR_SIZE
-+#define STM_8MB_BYTE_COUNT   STM_M25P64_BYTE_COUNT
-+#define STM_8MB_SECTOR_COUNT STM_M25P64_SECTOR_COUNT
-+#define STM_8MB_SECTOR_SIZE  STM_M25P64_SECTOR_SIZE
-+#define STM_16MB_BYTE_COUNT   STM_M25P128_BYTE_COUNT
-+#define STM_16MB_SECTOR_COUNT STM_M25P128_SECTOR_COUNT
-+#define STM_16MB_SECTOR_SIZE  STM_M25P128_SECTOR_SIZE
-+
-+/*
-+ * ST Microelectronics Opcodes for Serial Flash
-+ */
-+
-+#define STM_OP_WR_ENABLE       0x06     /* Write Enable */
-+#define STM_OP_WR_DISABLE      0x04     /* Write Disable */
-+#define STM_OP_RD_STATUS       0x05     /* Read Status */
-+#define STM_OP_WR_STATUS       0x01     /* Write Status */
-+#define STM_OP_RD_DATA         0x03     /* Read Data */
-+#define STM_OP_FAST_RD_DATA    0x0b     /* Fast Read Data */
-+#define STM_OP_PAGE_PGRM       0x02     /* Page Program */
-+#define STM_OP_SECTOR_ERASE    0xd8     /* Sector Erase */
-+#define STM_OP_BULK_ERASE      0xc7     /* Bulk Erase */
-+#define STM_OP_DEEP_PWRDOWN    0xb9     /* Deep Power-Down Mode */
-+#define STM_OP_RD_SIG          0xab     /* Read Electronic Signature */
-+
-+#define STM_STATUS_WIP       0x01       /* Write-In-Progress */
-+#define STM_STATUS_WEL       0x02       /* Write Enable Latch */
-+#define STM_STATUS_BP0       0x04       /* Block Protect 0 */
-+#define STM_STATUS_BP1       0x08       /* Block Protect 1 */
-+#define STM_STATUS_BP2       0x10       /* Block Protect 2 */
-+#define STM_STATUS_SRWD      0x80       /* Status Register Write Disable */
-+
-+/*
-+ * SPI Flash Interface Registers
-+ */
-+
-+#define SPI_FLASH_CTL           0x00
-+#define SPI_FLASH_OPCODE        0x04
-+#define SPI_FLASH_DATA          0x08
-+
-+#define SPI_CTL_START           0x00000100
-+#define SPI_CTL_BUSY            0x00010000
-+#define SPI_CTL_TXCNT_MASK      0x0000000f
-+#define SPI_CTL_RXCNT_MASK      0x000000f0
-+#define SPI_CTL_TX_RX_CNT_MASK  0x000000ff
-+#define SPI_CTL_SIZE_MASK       0x00060000
-+
-+#define SPI_CTL_CLK_SEL_MASK    0x03000000
-+#define SPI_OPCODE_MASK         0x000000ff
-+
-+#define SPI_STATUS_WIP		STM_STATUS_WIP
-+
-+#endif
---- a/arch/mips/ath25/ar2315.c
-+++ b/arch/mips/ath25/ar2315.c
-@@ -220,6 +220,28 @@ static struct platform_device ar2315_gpi
- 	.num_resources = ARRAY_SIZE(ar2315_gpio_res)
- };
- 
-+static struct resource ar2315_spiflash_res[] = {
-+	{
-+		.name = "spiflash_read",
-+		.flags = IORESOURCE_MEM,
-+		.start = AR2315_SPI_READ_BASE,
-+		.end = AR2315_SPI_READ_BASE + AR2315_SPI_READ_SIZE - 1,
-+	},
-+	{
-+		.name = "spiflash_mmr",
-+		.flags = IORESOURCE_MEM,
-+		.start = AR2315_SPI_MMR_BASE,
-+		.end = AR2315_SPI_MMR_BASE + AR2315_SPI_MMR_SIZE - 1,
-+	},
-+};
-+
-+static struct platform_device ar2315_spiflash = {
-+	.id = 0,
-+	.name = "ar2315-spiflash",
-+	.resource = ar2315_spiflash_res,
-+	.num_resources = ARRAY_SIZE(ar2315_spiflash_res)
-+};
-+
- void __init ar2315_init_devices(void)
- {
- 	/* Find board configuration */
-@@ -230,6 +252,8 @@ void __init ar2315_init_devices(void)
- 	ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
- 	platform_device_register(&ar2315_gpio);
- 
-+	platform_device_register(&ar2315_spiflash);
-+
- 	ar2315_eth_data.macaddr = ath25_board.config->enet0_mac;
- 	ath25_add_ethernet(0, AR2315_ENET0_BASE, "eth0_mii",
- 			   AR2315_ENET0_MII_BASE, AR2315_IRQ_ENET0,
diff --git a/target/linux/ath25/patches-3.18/130-watchdog.patch b/target/linux/ath25/patches-3.18/130-watchdog.patch
deleted file mode 100644
index 255064a..0000000
--- a/target/linux/ath25/patches-3.18/130-watchdog.patch
+++ /dev/null
@@ -1,277 +0,0 @@
---- /dev/null
-+++ b/drivers/watchdog/ar2315-wtd.c
-@@ -0,0 +1,209 @@
-+/*
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
-+ *
-+ * Copyright (C) 2008 John Crispin <blogic@openwrt.org>
-+ * Based on EP93xx and ifxmips wdt driver
-+ */
-+
-+#include <linux/interrupt.h>
-+#include <linux/module.h>
-+#include <linux/moduleparam.h>
-+#include <linux/types.h>
-+#include <linux/miscdevice.h>
-+#include <linux/watchdog.h>
-+#include <linux/fs.h>
-+#include <linux/ioport.h>
-+#include <linux/notifier.h>
-+#include <linux/reboot.h>
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <linux/io.h>
-+#include <linux/uaccess.h>
-+
-+#define DRIVER_NAME	"ar2315-wdt"
-+
-+#define CLOCK_RATE 40000000
-+#define HEARTBEAT(x) (x < 1 || x > 90 ? 20 : x)
-+
-+#define WDT_REG_TIMER		0x00
-+#define WDT_REG_CTRL		0x04
-+
-+#define WDT_CTRL_ACT_NONE	0x00000000	/* No action */
-+#define WDT_CTRL_ACT_NMI	0x00000001	/* NMI on watchdog */
-+#define WDT_CTRL_ACT_RESET	0x00000002	/* reset on watchdog */
-+
-+static int wdt_timeout = 20;
-+static int started;
-+static int in_use;
-+static void __iomem *wdt_base;
-+
-+static inline void ar2315_wdt_wr(unsigned reg, u32 val)
-+{
-+	iowrite32(val, wdt_base + reg);
-+}
-+
-+static void
-+ar2315_wdt_enable(void)
-+{
-+	ar2315_wdt_wr(WDT_REG_TIMER, wdt_timeout * CLOCK_RATE);
-+}
-+
-+static ssize_t
-+ar2315_wdt_write(struct file *file, const char __user *data, size_t len,
-+		 loff_t *ppos)
-+{
-+	if (len)
-+		ar2315_wdt_enable();
-+	return len;
-+}
-+
-+static int
-+ar2315_wdt_open(struct inode *inode, struct file *file)
-+{
-+	if (in_use)
-+		return -EBUSY;
-+	ar2315_wdt_enable();
-+	in_use = 1;
-+	started = 1;
-+	return nonseekable_open(inode, file);
-+}
-+
-+static int
-+ar2315_wdt_release(struct inode *inode, struct file *file)
-+{
-+	in_use = 0;
-+	return 0;
-+}
-+
-+static irqreturn_t
-+ar2315_wdt_interrupt(int irq, void *dev)
-+{
-+	struct platform_device *pdev = (struct platform_device *)dev;
-+
-+	if (started) {
-+		dev_crit(&pdev->dev, "watchdog expired, rebooting system\n");
-+		emergency_restart();
-+	} else {
-+		ar2315_wdt_wr(WDT_REG_CTRL, 0);
-+		ar2315_wdt_wr(WDT_REG_TIMER, 0);
-+	}
-+	return IRQ_HANDLED;
-+}
-+
-+static struct watchdog_info ident = {
-+	.options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
-+	.identity = "ar2315 Watchdog",
-+};
-+
-+static long
-+ar2315_wdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-+{
-+	int new_wdt_timeout;
-+	int ret = -ENOIOCTLCMD;
-+
-+	switch (cmd) {
-+	case WDIOC_GETSUPPORT:
-+		ret = copy_to_user((void __user *)arg, &ident, sizeof(ident)) ?
-+		      -EFAULT : 0;
-+		break;
-+	case WDIOC_KEEPALIVE:
-+		ar2315_wdt_enable();
-+		ret = 0;
-+		break;
-+	case WDIOC_SETTIMEOUT:
-+		ret = get_user(new_wdt_timeout, (int __user *)arg);
-+		if (ret)
-+			break;
-+		wdt_timeout = HEARTBEAT(new_wdt_timeout);
-+		ar2315_wdt_enable();
-+		break;
-+	case WDIOC_GETTIMEOUT:
-+		ret = put_user(wdt_timeout, (int __user *)arg);
-+		break;
-+	}
-+	return ret;
-+}
-+
-+static const struct file_operations ar2315_wdt_fops = {
-+	.owner		= THIS_MODULE,
-+	.llseek		= no_llseek,
-+	.write		= ar2315_wdt_write,
-+	.unlocked_ioctl	= ar2315_wdt_ioctl,
-+	.open		= ar2315_wdt_open,
-+	.release	= ar2315_wdt_release,
-+};
-+
-+static struct miscdevice ar2315_wdt_miscdev = {
-+	.minor	= WATCHDOG_MINOR,
-+	.name	= "watchdog",
-+	.fops	= &ar2315_wdt_fops,
-+};
-+
-+static int
-+ar2315_wdt_probe(struct platform_device *dev)
-+{
-+	struct resource *mem_res, *irq_res;
-+	int ret = 0;
-+
-+	if (wdt_base)
-+		return -EBUSY;
-+
-+	irq_res = platform_get_resource(dev, IORESOURCE_IRQ, 0);
-+	if (!irq_res) {
-+		dev_err(&dev->dev, "no IRQ resource\n");
-+		return -ENOENT;
-+	}
-+
-+	mem_res = platform_get_resource(dev, IORESOURCE_MEM, 0);
-+	wdt_base = devm_ioremap_resource(&dev->dev, mem_res);
-+	if (IS_ERR(wdt_base))
-+		return PTR_ERR(wdt_base);
-+
-+	ret = devm_request_irq(&dev->dev, irq_res->start, ar2315_wdt_interrupt,
-+			       IRQF_DISABLED, DRIVER_NAME, dev);
-+	if (ret) {
-+		dev_err(&dev->dev, "failed to register inetrrupt\n");
-+		goto out;
-+	}
-+
-+	ret = misc_register(&ar2315_wdt_miscdev);
-+	if (ret)
-+		dev_err(&dev->dev, "failed to register miscdev\n");
-+
-+out:
-+	return ret;
-+}
-+
-+static int
-+ar2315_wdt_remove(struct platform_device *dev)
-+{
-+	misc_deregister(&ar2315_wdt_miscdev);
-+	return 0;
-+}
-+
-+static struct platform_driver ar2315_wdt_driver = {
-+	.probe = ar2315_wdt_probe,
-+	.remove = ar2315_wdt_remove,
-+	.driver = {
-+		.name = DRIVER_NAME,
-+		.owner = THIS_MODULE,
-+	},
-+};
-+
-+module_platform_driver(ar2315_wdt_driver);
-+
-+MODULE_DESCRIPTION("Atheros AR2315 hardware watchdog driver");
-+MODULE_AUTHOR("John Crispin <blogic@openwrt.org>");
-+MODULE_LICENSE("GPL");
-+MODULE_ALIAS("platform:" DRIVER_NAME);
---- a/drivers/watchdog/Kconfig
-+++ b/drivers/watchdog/Kconfig
-@@ -1257,6 +1257,13 @@ config RALINK_WDT
- 	help
- 	  Hardware driver for the Ralink SoC Watchdog Timer.
- 
-+config AR2315_WDT
-+	tristate "Atheros AR2315+ WiSoCs Watchdog Timer"
-+	depends on ATH25
-+	help
-+	  Hardware driver for the built-in watchdog timer on the Atheros
-+	  AR2315/AR2316 WiSoCs.
-+
- # PARISC Architecture
- 
- # POWERPC Architecture
---- a/drivers/watchdog/Makefile
-+++ b/drivers/watchdog/Makefile
-@@ -138,6 +138,7 @@ obj-$(CONFIG_GPIO_WDT) += old_gpio_wdt.o
- obj-$(CONFIG_PNX833X_WDT) += pnx833x_wdt.o
- obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o
- obj-$(CONFIG_AR7_WDT) += ar7_wdt.o
-+obj-$(CONFIG_AR2315_WDT) += ar2315-wtd.o
- obj-$(CONFIG_TXX9_WDT) += txx9wdt.o
- obj-$(CONFIG_OCTEON_WDT) += octeon-wdt.o
- octeon-wdt-y := octeon-wdt-main.o octeon-wdt-nmi.o
---- a/arch/mips/ath25/ar2315.c
-+++ b/arch/mips/ath25/ar2315.c
-@@ -220,6 +220,24 @@ static struct platform_device ar2315_gpi
- 	.num_resources = ARRAY_SIZE(ar2315_gpio_res)
- };
- 
-+static struct resource ar2315_wdt_res[] = {
-+	{
-+		.flags = IORESOURCE_MEM,
-+		.start = AR2315_RST_BASE + AR2315_WDT_TIMER,
-+		.end = AR2315_RST_BASE + AR2315_WDT_TIMER + 8 - 1,
-+	},
-+	{
-+		.flags = IORESOURCE_IRQ,
-+	}
-+};
-+
-+static struct platform_device ar2315_wdt = {
-+	.id = 0,
-+	.name = "ar2315-wdt",
-+	.resource = ar2315_wdt_res,
-+	.num_resources = ARRAY_SIZE(ar2315_wdt_res)
-+};
-+
- static struct resource ar2315_spiflash_res[] = {
- 	{
- 		.name = "spiflash_read",
-@@ -252,6 +270,11 @@ void __init ar2315_init_devices(void)
- 	ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
- 	platform_device_register(&ar2315_gpio);
- 
-+	ar2315_wdt_res[1].start = irq_create_mapping(ar2315_misc_irq_domain,
-+						     AR2315_MISC_IRQ_WATCHDOG);
-+	ar2315_wdt_res[1].end = ar2315_wdt_res[1].start;
-+	platform_device_register(&ar2315_wdt);
-+
- 	platform_device_register(&ar2315_spiflash);
- 
- 	ar2315_eth_data.macaddr = ath25_board.config->enet0_mac;
diff --git a/target/linux/ath25/patches-3.18/140-redboot_boardconfig.patch b/target/linux/ath25/patches-3.18/140-redboot_boardconfig.patch
deleted file mode 100644
index 98dbf52..0000000
--- a/target/linux/ath25/patches-3.18/140-redboot_boardconfig.patch
+++ /dev/null
@@ -1,60 +0,0 @@
---- a/drivers/mtd/redboot.c
-+++ b/drivers/mtd/redboot.c
-@@ -30,6 +30,8 @@
- #include <linux/mtd/partitions.h>
- #include <linux/module.h>
- 
-+#define BOARD_CONFIG_PART		"boardconfig"
-+
- struct fis_image_desc {
-     unsigned char name[16];      // Null terminated name
-     uint32_t	  flash_base;    // Address within FLASH of image
-@@ -60,6 +62,7 @@ static int parse_redboot_partitions(stru
- 				    struct mtd_partition **pparts,
- 				    struct mtd_part_parser_data *data)
- {
-+	unsigned long max_offset = 0;
- 	int nrparts = 0;
- 	struct fis_image_desc *buf;
- 	struct mtd_partition *parts;
-@@ -225,14 +228,15 @@ static int parse_redboot_partitions(stru
- 		}
- 	}
- #endif
--	parts = kzalloc(sizeof(*parts)*nrparts + nulllen + namelen, GFP_KERNEL);
-+	parts = kzalloc(sizeof(*parts) * (nrparts + 1) + nulllen + namelen +
-+			sizeof(BOARD_CONFIG_PART), GFP_KERNEL);
- 
- 	if (!parts) {
- 		ret = -ENOMEM;
- 		goto out;
- 	}
- 
--	nullname = (char *)&parts[nrparts];
-+	nullname = (char *)&parts[nrparts + 1];
- #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED
- 	if (nulllen > 0) {
- 		strcpy(nullname, nullstring);
-@@ -251,6 +255,8 @@ static int parse_redboot_partitions(stru
- 	}
- #endif
- 	for ( ; i<nrparts; i++) {
-+		if (max_offset < buf[i].flash_base + buf[i].size)
-+			max_offset = buf[i].flash_base + buf[i].size;
- 		parts[i].size = fl->img->size;
- 		parts[i].offset = fl->img->flash_base;
- 		parts[i].name = names;
-@@ -284,6 +290,13 @@ static int parse_redboot_partitions(stru
- 		fl = fl->next;
- 		kfree(tmp_fl);
- 	}
-+	if (master->size - max_offset >= master->erasesize) {
-+		parts[nrparts].size = master->size - max_offset;
-+		parts[nrparts].offset = max_offset;
-+		parts[nrparts].name = names;
-+		strcpy(names, BOARD_CONFIG_PART);
-+		nrparts++;
-+	}
- 	ret = nrparts;
- 	*pparts = parts;
-  out:
diff --git a/target/linux/ath25/patches-3.18/141-redboot_partition_scan.patch b/target/linux/ath25/patches-3.18/141-redboot_partition_scan.patch
deleted file mode 100644
index d1d281e..0000000
--- a/target/linux/ath25/patches-3.18/141-redboot_partition_scan.patch
+++ /dev/null
@@ -1,44 +0,0 @@
---- a/drivers/mtd/redboot.c
-+++ b/drivers/mtd/redboot.c
-@@ -79,12 +79,18 @@ static int parse_redboot_partitions(stru
- 	static char nullstring[] = "unallocated";
- #endif
- 
-+	buf = vmalloc(master->erasesize);
-+	if (!buf)
-+		return -ENOMEM;
-+
-+ restart:
- 	if ( directory < 0 ) {
- 		offset = master->size + directory * master->erasesize;
- 		while (mtd_block_isbad(master, offset)) {
- 			if (!offset) {
- 			nogood:
- 				printk(KERN_NOTICE "Failed to find a non-bad block to check for RedBoot partition table\n");
-+				vfree(buf);
- 				return -EIO;
- 			}
- 			offset -= master->erasesize;
-@@ -97,10 +103,6 @@ static int parse_redboot_partitions(stru
- 				goto nogood;
- 		}
- 	}
--	buf = vmalloc(master->erasesize);
--
--	if (!buf)
--		return -ENOMEM;
- 
- 	printk(KERN_NOTICE "Searching for RedBoot partition table in %s at offset 0x%lx\n",
- 	       master->name, offset);
-@@ -173,6 +175,11 @@ static int parse_redboot_partitions(stru
- 	}
- 	if (i == numslots) {
- 		/* Didn't find it */
-+		if (offset + master->erasesize < master->size) {
-+			/* not at the end of the flash yet, maybe next block */
-+			directory++;
-+			goto restart;
-+		}
- 		printk(KERN_NOTICE "No RedBoot partition table detected in %s\n",
- 		       master->name);
- 		ret = 0;
diff --git a/target/linux/ath25/patches-3.18/142-redboot_various_erase_size_fix.patch b/target/linux/ath25/patches-3.18/142-redboot_various_erase_size_fix.patch
deleted file mode 100644
index e1b0a89..0000000
--- a/target/linux/ath25/patches-3.18/142-redboot_various_erase_size_fix.patch
+++ /dev/null
@@ -1,72 +0,0 @@
---- a/drivers/mtd/redboot.c
-+++ b/drivers/mtd/redboot.c
-@@ -58,6 +58,22 @@ static inline int redboot_checksum(struc
- 	return 1;
- }
- 
-+static uint32_t mtd_get_offset_erasesize(struct mtd_info *mtd, uint64_t offset)
-+{
-+	struct mtd_erase_region_info *regions = mtd->eraseregions;
-+	int i;
-+
-+	for (i = 0; i < mtd->numeraseregions; i++) {
-+		if (regions[i].offset +
-+		    regions[i].numblocks * regions[i].erasesize <= offset)
-+			continue;
-+
-+		return regions[i].erasesize;
-+	}
-+
-+	return mtd->erasesize;
-+}
-+
- static int parse_redboot_partitions(struct mtd_info *master,
- 				    struct mtd_partition **pparts,
- 				    struct mtd_part_parser_data *data)
-@@ -74,6 +90,7 @@ static int parse_redboot_partitions(stru
- 	int namelen = 0;
- 	int nulllen = 0;
- 	int numslots;
-+	int first_slot;
- 	unsigned long offset;
- #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED
- 	static char nullstring[] = "unallocated";
-@@ -186,7 +203,10 @@ static int parse_redboot_partitions(stru
- 		goto out;
- 	}
- 
--	for (i = 0; i < numslots; i++) {
-+	first_slot = (buf[i].flash_base & (master->erasesize - 1)) /
-+		     sizeof(struct fis_image_desc);
-+
-+	for (i = first_slot; i < first_slot + numslots; i++) {
- 		struct fis_list *new_fl, **prev;
- 
- 		if (buf[i].name[0] == 0xff) {
-@@ -262,12 +282,13 @@ static int parse_redboot_partitions(stru
- 	}
- #endif
- 	for ( ; i<nrparts; i++) {
--		if (max_offset < buf[i].flash_base + buf[i].size)
--			max_offset = buf[i].flash_base + buf[i].size;
- 		parts[i].size = fl->img->size;
- 		parts[i].offset = fl->img->flash_base;
- 		parts[i].name = names;
- 
-+		if (max_offset < parts[i].offset + parts[i].size)
-+			max_offset = parts[i].offset + parts[i].size;
-+
- 		strcpy(names, fl->img->name);
- #ifdef CONFIG_MTD_REDBOOT_PARTS_READONLY
- 		if (!memcmp(names, "RedBoot", 8) ||
-@@ -297,7 +318,9 @@ static int parse_redboot_partitions(stru
- 		fl = fl->next;
- 		kfree(tmp_fl);
- 	}
--	if (master->size - max_offset >= master->erasesize) {
-+
-+	if (master->size - max_offset >=
-+	    mtd_get_offset_erasesize(master, max_offset)) {
- 		parts[nrparts].size = master->size - max_offset;
- 		parts[nrparts].offset = max_offset;
- 		parts[nrparts].name = names;
diff --git a/target/linux/ath25/patches-3.18/210-reset_button.patch b/target/linux/ath25/patches-3.18/210-reset_button.patch
deleted file mode 100644
index 34ef46b..0000000
--- a/target/linux/ath25/patches-3.18/210-reset_button.patch
+++ /dev/null
@@ -1,71 +0,0 @@
---- a/arch/mips/ath25/Makefile
-+++ b/arch/mips/ath25/Makefile
-@@ -8,7 +8,7 @@
- # Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
- #
- 
--obj-y += board.o prom.o devices.o
-+obj-y += board.o prom.o devices.o reset.o
- 
- obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
- 
---- /dev/null
-+++ b/arch/mips/ath25/reset.c
-@@ -0,0 +1,57 @@
-+#include <linux/init.h>
-+#include <linux/slab.h>
-+#include <linux/platform_device.h>
-+#include <linux/gpio_keys.h>
-+#include <linux/input.h>
-+#include <ath25_platform.h>
-+#include "devices.h"
-+
-+static int __init
-+ar231x_init_reset(void)
-+{
-+	struct platform_device *pdev;
-+	struct gpio_keys_platform_data pdata;
-+	struct gpio_keys_button *p;
-+	int err;
-+
-+	if (ath25_board.config->reset_config_gpio == 0xffff)
-+		return -ENODEV;
-+
-+	p = kzalloc(sizeof(*p), GFP_KERNEL);
-+	if (!p)
-+		goto err;
-+
-+	p->desc = "reset";
-+	p->type = EV_KEY;
-+	p->code = KEY_RESTART;
-+	p->debounce_interval = 60;
-+	p->gpio = ath25_board.config->reset_config_gpio;
-+
-+	memset(&pdata, 0, sizeof(pdata));
-+	pdata.poll_interval = 20;
-+	pdata.buttons = p;
-+	pdata.nbuttons = 1;
-+
-+	pdev = platform_device_alloc("gpio-keys-polled", 0);
-+	if (!pdev)
-+		goto err_free;
-+
-+	err = platform_device_add_data(pdev, &pdata, sizeof(pdata));
-+	if (err)
-+		goto err_put_pdev;
-+
-+	err = platform_device_add(pdev);
-+	if (err)
-+		goto err_put_pdev;
-+
-+	return 0;
-+
-+err_put_pdev:
-+	platform_device_put(pdev);
-+err_free:
-+	kfree(p);
-+err:
-+	return -ENOMEM;
-+}
-+
-+module_init(ar231x_init_reset);
diff --git a/target/linux/ath25/patches-3.18/220-enet_micrel_workaround.patch b/target/linux/ath25/patches-3.18/220-enet_micrel_workaround.patch
deleted file mode 100644
index 398495a..0000000
--- a/target/linux/ath25/patches-3.18/220-enet_micrel_workaround.patch
+++ /dev/null
@@ -1,91 +0,0 @@
---- a/drivers/net/ethernet/atheros/ar231x/ar231x.c
-+++ b/drivers/net/ethernet/atheros/ar231x/ar231x.c
-@@ -135,6 +135,7 @@ static int ar231x_mdiobus_write(struct m
- static int ar231x_mdiobus_reset(struct mii_bus *bus);
- static int ar231x_mdiobus_probe(struct net_device *dev);
- static void ar231x_adjust_link(struct net_device *dev);
-+static bool no_phy;
- 
- #ifndef ERR
- #define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args)
-@@ -167,6 +168,32 @@ static const struct net_device_ops ar231
- #endif
- };
- 
-+static int get_phy_id(struct mii_bus *bus, int addr, u32 *phy_id)
-+{
-+	int phy_reg;
-+
-+	/**
-+	 * Grab the bits from PHYIR1, and put them
-+	 * in the upper half.
-+	 */
-+	phy_reg = mdiobus_read(bus, addr, MII_PHYSID1);
-+
-+	if (phy_reg < 0)
-+		return -EIO;
-+
-+	*phy_id = (phy_reg & 0xffff) << 16;
-+
-+	/* Grab the bits from PHYIR2, and put them in the lower half */
-+	phy_reg = mdiobus_read(bus, addr, MII_PHYSID2);
-+
-+	if (phy_reg < 0)
-+		return -EIO;
-+
-+	*phy_id |= (phy_reg & 0xffff);
-+
-+	return 0;
-+}
-+
- static int ar231x_probe(struct platform_device *pdev)
- {
- 	struct net_device *dev;
-@@ -273,6 +300,24 @@ static int ar231x_probe(struct platform_
- 
- 	mdiobus_register(sp->mii_bus);
- 
-+	/**
-+	 * Workaround for Micrel switch, which is only available on
-+	 * one PHY and cannot be configured through MDIO.
-+	 */
-+	if (!no_phy) {
-+		u32 phy_id = 0;
-+
-+		get_phy_id(sp->mii_bus, 1, &phy_id);
-+		if (phy_id == 0x00221450)
-+			no_phy = true;
-+	}
-+	if (no_phy) {
-+		sp->link = 1;
-+		netif_carrier_on(dev);
-+		return 0;
-+	}
-+	no_phy = true;
-+
- 	if (ar231x_mdiobus_probe(dev) != 0) {
- 		printk(KERN_ERR "%s: mdiobus_probe failed\n", dev->name);
- 		rx_tasklet_cleanup(dev);
-@@ -329,8 +374,10 @@ static int ar231x_remove(struct platform
- 	rx_tasklet_cleanup(dev);
- 	ar231x_init_cleanup(dev);
- 	unregister_netdev(dev);
--	mdiobus_unregister(sp->mii_bus);
--	mdiobus_free(sp->mii_bus);
-+	if (sp->mii_bus) {
-+		mdiobus_unregister(sp->mii_bus);
-+		mdiobus_free(sp->mii_bus);
-+	}
- 	kfree(dev);
- 	return 0;
- }
-@@ -1079,6 +1126,9 @@ static int ar231x_ioctl(struct net_devic
- {
- 	struct ar231x_private *sp = netdev_priv(dev);
- 
-+	if (!sp->phy_dev)
-+		return -ENODEV;
-+
- 	switch (cmd) {
- 	case SIOCGMIIPHY:
- 	case SIOCGMIIREG:
diff --git a/target/linux/ath25/patches-3.18/330-board_leds.patch b/target/linux/ath25/patches-3.18/330-board_leds.patch
deleted file mode 100644
index e357fc6..0000000
--- a/target/linux/ath25/patches-3.18/330-board_leds.patch
+++ /dev/null
@@ -1,116 +0,0 @@
---- a/arch/mips/ath25/ar2315.c
-+++ b/arch/mips/ath25/ar2315.c
-@@ -23,6 +23,7 @@
- #include <linux/reboot.h>
- #include <linux/delay.h>
- #include <linux/gpio.h>
-+#include <linux/leds.h>
- #include <asm/bootinfo.h>
- #include <asm/reboot.h>
- #include <asm/time.h>
-@@ -260,6 +261,50 @@ static struct platform_device ar2315_spi
- 	.num_resources = ARRAY_SIZE(ar2315_spiflash_res)
- };
- 
-+#ifdef CONFIG_LEDS_GPIO
-+static struct gpio_led ar2315_leds[6];
-+static struct gpio_led_platform_data ar2315_led_data = {
-+	.leds = (void *)ar2315_leds,
-+};
-+
-+static struct platform_device ar2315_gpio_leds = {
-+	.name = "leds-gpio",
-+	.id = -1,
-+	.dev = {
-+		.platform_data = (void *)&ar2315_led_data,
-+	}
-+};
-+
-+static void __init ar2315_init_gpio_leds(void)
-+{
-+	static char led_names[6][6];
-+	int i, led = 0;
-+
-+	ar2315_led_data.num_leds = 0;
-+	for (i = 1; i < 8; i++) {
-+		if ((i == AR2315_RESET_GPIO) ||
-+		    (i == ath25_board.config->reset_config_gpio))
-+			continue;
-+
-+		if (i == ath25_board.config->sys_led_gpio)
-+			strcpy(led_names[led], "wlan");
-+		else
-+			sprintf(led_names[led], "gpio%d", i);
-+
-+		ar2315_leds[led].name = led_names[led];
-+		ar2315_leds[led].gpio = i;
-+		ar2315_leds[led].active_low = 0;
-+		led++;
-+	}
-+	ar2315_led_data.num_leds = led;
-+	platform_device_register(&ar2315_gpio_leds);
-+}
-+#else
-+static inline void ar2315_init_gpio_leds(void)
-+{
-+}
-+#endif
-+
- void __init ar2315_init_devices(void)
- {
- 	/* Find board configuration */
-@@ -270,6 +315,8 @@ void __init ar2315_init_devices(void)
- 	ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
- 	platform_device_register(&ar2315_gpio);
- 
-+	ar2315_init_gpio_leds();
-+
- 	ar2315_wdt_res[1].start = irq_create_mapping(ar2315_misc_irq_domain,
- 						     AR2315_MISC_IRQ_WATCHDOG);
- 	ar2315_wdt_res[1].end = ar2315_wdt_res[1].start;
---- a/arch/mips/ath25/ar5312.c
-+++ b/arch/mips/ath25/ar5312.c
-@@ -23,6 +23,7 @@
- #include <linux/mtd/physmap.h>
- #include <linux/reboot.h>
- #include <linux/gpio.h>
-+#include <linux/leds.h>
- #include <asm/bootinfo.h>
- #include <asm/reboot.h>
- #include <asm/time.h>
-@@ -231,6 +232,23 @@ static struct platform_device ar5312_gpi
- 	.num_resources = ARRAY_SIZE(ar5312_gpio_res),
- };
- 
-+#ifdef CONFIG_LEDS_GPIO
-+static struct gpio_led ar5312_leds[] = {
-+	{ .name = "wlan", .gpio = 0, .active_low = 1, },
-+};
-+
-+static const struct gpio_led_platform_data ar5312_led_data = {
-+	.num_leds = ARRAY_SIZE(ar5312_leds),
-+	.leds = (void *)ar5312_leds,
-+};
-+
-+static struct platform_device ar5312_gpio_leds = {
-+	.name = "leds-gpio",
-+	.id = -1,
-+	.dev.platform_data = (void *)&ar5312_led_data,
-+};
-+#endif
-+
- static void __init ar5312_flash_init(void)
- {
- 	void __iomem *flashctl_base;
-@@ -301,6 +319,11 @@ void __init ar5312_init_devices(void)
- 
- 	platform_device_register(&ar5312_gpio);
- 
-+#ifdef CONFIG_LEDS_GPIO
-+	ar5312_leds[0].gpio = config->sys_led_gpio;
-+	platform_device_register(&ar5312_gpio_leds);
-+#endif
-+
- 	/* Fix up MAC addresses if necessary */
- 	if (is_broadcast_ether_addr(config->enet0_mac))
- 		ether_addr_copy(config->enet0_mac, config->enet1_mac);
diff --git a/target/linux/ath25/patches-4.4/010-board.patch b/target/linux/ath25/patches-4.4/010-board.patch
new file mode 100644
index 0000000..dbf0600
--- /dev/null
+++ b/target/linux/ath25/patches-4.4/010-board.patch
@@ -0,0 +1,47 @@
+--- /dev/null
++++ b/arch/mips/include/asm/mach-ath25/gpio.h
+@@ -0,0 +1,16 @@
++#ifndef __ASM_MACH_ATH25_GPIO_H
++#define __ASM_MACH_ATH25_GPIO_H
++
++#include <asm-generic/gpio.h>
++
++#define gpio_get_value __gpio_get_value
++#define gpio_set_value __gpio_set_value
++#define gpio_cansleep __gpio_cansleep
++#define gpio_to_irq __gpio_to_irq
++
++static inline int irq_to_gpio(unsigned irq)
++{
++	return -EINVAL;
++}
++
++#endif	/* __ASM_MACH_ATH25_GPIO_H */
+--- /dev/null
++++ b/arch/mips/include/asm/mach-ath25/war.h
+@@ -0,0 +1,25 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2008 Felix Fietkau <nbd@openwrt.org>
++ */
++#ifndef __ASM_MACH_ATH25_WAR_H
++#define __ASM_MACH_ATH25_WAR_H
++
++#define R4600_V1_INDEX_ICACHEOP_WAR	0
++#define R4600_V1_HIT_CACHEOP_WAR	0
++#define R4600_V2_HIT_CACHEOP_WAR	0
++#define R5432_CP0_INTERRUPT_WAR		0
++#define BCM1250_M3_WAR			0
++#define SIBYTE_1956_WAR			0
++#define MIPS4K_ICACHE_REFILL_WAR	0
++#define MIPS_CACHE_SYNC_WAR		0
++#define TX49XX_ICACHE_INDEX_INV_WAR	0
++#define RM9000_CDEX_SMP_WAR		0
++#define ICACHE_REFILLS_WORKAROUND_WAR	0
++#define R10000_LLSC_WAR			0
++#define MIPS34K_MISSED_ITLB_WAR		0
++
++#endif /* __ASM_MACH_ATH25_WAR_H */
diff --git a/target/linux/ath25/patches-4.4/107-ar5312_gpio.patch b/target/linux/ath25/patches-4.4/107-ar5312_gpio.patch
new file mode 100644
index 0000000..84f9fbd
--- /dev/null
+++ b/target/linux/ath25/patches-4.4/107-ar5312_gpio.patch
@@ -0,0 +1,212 @@
+--- a/arch/mips/ath25/Kconfig
++++ b/arch/mips/ath25/Kconfig
+@@ -1,6 +1,7 @@
+ config SOC_AR5312
+ 	bool "Atheros AR5312/AR2312+ SoC support"
+ 	depends on ATH25
++	select GPIO_AR5312
+ 	default y
+ 
+ config SOC_AR2315
+--- a/arch/mips/ath25/ar5312.c
++++ b/arch/mips/ath25/ar5312.c
+@@ -22,6 +22,7 @@
+ #include <linux/platform_device.h>
+ #include <linux/mtd/physmap.h>
+ #include <linux/reboot.h>
++#include <linux/gpio.h>
+ #include <asm/bootinfo.h>
+ #include <asm/reboot.h>
+ #include <asm/time.h>
+@@ -180,6 +181,22 @@ static struct platform_device ar5312_phy
+ 	.num_resources = 1,
+ };
+ 
++static struct resource ar5312_gpio_res[] = {
++	{
++		.name = "ar5312-gpio",
++		.flags = IORESOURCE_MEM,
++		.start = AR5312_GPIO_BASE,
++		.end = AR5312_GPIO_BASE + AR5312_GPIO_SIZE - 1,
++	},
++};
++
++static struct platform_device ar5312_gpio = {
++	.name = "ar5312-gpio",
++	.id = -1,
++	.resource = ar5312_gpio_res,
++	.num_resources = ARRAY_SIZE(ar5312_gpio_res),
++};
++
+ static void __init ar5312_flash_init(void)
+ {
+ 	void __iomem *flashctl_base;
+@@ -247,6 +264,8 @@ void __init ar5312_init_devices(void)
+ 
+ 	platform_device_register(&ar5312_physmap_flash);
+ 
++	platform_device_register(&ar5312_gpio);
++
+ 	switch (ath25_soc) {
+ 	case ATH25_SOC_AR5312:
+ 		if (!ath25_board.radio)
+--- a/drivers/gpio/Kconfig
++++ b/drivers/gpio/Kconfig
+@@ -141,6 +141,13 @@ config GPIO_BRCMSTB
+ 	help
+ 	  Say yes here to enable GPIO support for Broadcom STB (BCM7XXX) SoCs.
+ 
++config GPIO_AR5312
++	bool "AR5312 SoC GPIO support"
++	default y if SOC_AR5312
++	depends on SOC_AR5312
++	help
++	  Say yes here to enable GPIO support for Atheros AR5312/AR2312+ SoCs.
++
+ config GPIO_CLPS711X
+ 	tristate "CLPS711X GPIO support"
+ 	depends on ARCH_CLPS711X || COMPILE_TEST
+--- a/drivers/gpio/Makefile
++++ b/drivers/gpio/Makefile
+@@ -21,6 +21,7 @@ obj-$(CONFIG_GPIO_ADP5588)	+= gpio-adp55
+ obj-$(CONFIG_GPIO_ALTERA)  	+= gpio-altera.o
+ obj-$(CONFIG_GPIO_AMD8111)	+= gpio-amd8111.o
+ obj-$(CONFIG_GPIO_AMDPT)	+= gpio-amdpt.o
++obj-$(CONFIG_GPIO_AR5312)	+= gpio-ar5312.o
+ obj-$(CONFIG_GPIO_ARIZONA)	+= gpio-arizona.o
+ obj-$(CONFIG_ATH79)		+= gpio-ath79.o
+ obj-$(CONFIG_GPIO_BCM_KONA)	+= gpio-bcm-kona.o
+--- /dev/null
++++ b/drivers/gpio/gpio-ar5312.c
+@@ -0,0 +1,121 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
++ * Copyright (C) 2006 FON Technology, SL.
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/gpio.h>
++
++#define DRIVER_NAME	"ar5312-gpio"
++
++#define AR5312_GPIO_DO		0x00		/* output register */
++#define AR5312_GPIO_DI		0x04		/* intput register */
++#define AR5312_GPIO_CR		0x08		/* control register */
++
++#define AR5312_GPIO_CR_M(x)	(1 << (x))	/* mask for i/o */
++#define AR5312_GPIO_CR_O(x)	(0 << (x))	/* mask for output */
++#define AR5312_GPIO_CR_I(x)	(1 << (x))	/* mask for input */
++#define AR5312_GPIO_CR_INT(x)	(1 << ((x)+8))	/* mask for interrupt */
++#define AR5312_GPIO_CR_UART(x)	(1 << ((x)+16))	/* uart multiplex */
++
++#define AR5312_GPIO_NUM		8
++
++static void __iomem *ar5312_mem;
++
++static inline u32 ar5312_gpio_reg_read(unsigned reg)
++{
++	return __raw_readl(ar5312_mem + reg);
++}
++
++static inline void ar5312_gpio_reg_write(unsigned reg, u32 val)
++{
++	__raw_writel(val, ar5312_mem + reg);
++}
++
++static inline void ar5312_gpio_reg_mask(unsigned reg, u32 mask, u32 val)
++{
++	ar5312_gpio_reg_write(reg, (ar5312_gpio_reg_read(reg) & ~mask) | val);
++}
++
++static int ar5312_gpio_get_val(struct gpio_chip *chip, unsigned gpio)
++{
++	return (ar5312_gpio_reg_read(AR5312_GPIO_DI) >> gpio) & 1;
++}
++
++static void ar5312_gpio_set_val(struct gpio_chip *chip, unsigned gpio, int val)
++{
++	u32 reg = ar5312_gpio_reg_read(AR5312_GPIO_DO);
++
++	reg = val ? reg | (1 << gpio) : reg & ~(1 << gpio);
++	ar5312_gpio_reg_write(AR5312_GPIO_DO, reg);
++}
++
++static int ar5312_gpio_dir_in(struct gpio_chip *chip, unsigned gpio)
++{
++	ar5312_gpio_reg_mask(AR5312_GPIO_CR, 0, 1 << gpio);
++	return 0;
++}
++
++static int ar5312_gpio_dir_out(struct gpio_chip *chip, unsigned gpio, int val)
++{
++	ar5312_gpio_reg_mask(AR5312_GPIO_CR, 1 << gpio, 0);
++	ar5312_gpio_set_val(chip, gpio, val);
++	return 0;
++}
++
++static struct gpio_chip ar5312_gpio_chip = {
++	.label			= DRIVER_NAME,
++	.direction_input	= ar5312_gpio_dir_in,
++	.direction_output	= ar5312_gpio_dir_out,
++	.set			= ar5312_gpio_set_val,
++	.get			= ar5312_gpio_get_val,
++	.base			= 0,
++	.ngpio			= AR5312_GPIO_NUM,
++};
++
++static int ar5312_gpio_probe(struct platform_device *pdev)
++{
++	struct device *dev = &pdev->dev;
++	struct resource *res;
++	int ret;
++
++	if (ar5312_mem)
++		return -EBUSY;
++
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	ar5312_mem = devm_ioremap_resource(dev, res);
++	if (IS_ERR(ar5312_mem))
++		return PTR_ERR(ar5312_mem);
++
++	ar5312_gpio_chip.dev = dev;
++	ret = gpiochip_add(&ar5312_gpio_chip);
++	if (ret) {
++		dev_err(dev, "failed to add gpiochip\n");
++		return ret;
++	}
++
++	return 0;
++}
++
++static struct platform_driver ar5312_gpio_driver = {
++	.probe = ar5312_gpio_probe,
++	.driver = {
++		.name = DRIVER_NAME,
++		.owner = THIS_MODULE,
++	}
++};
++
++static int __init ar5312_gpio_init(void)
++{
++	return platform_driver_register(&ar5312_gpio_driver);
++}
++subsys_initcall(ar5312_gpio_init);
+--- a/arch/mips/Kconfig
++++ b/arch/mips/Kconfig
+@@ -117,6 +117,7 @@ config ATH25
+ 	select SYS_SUPPORTS_BIG_ENDIAN
+ 	select SYS_SUPPORTS_32BIT_KERNEL
+ 	select SYS_HAS_EARLY_PRINTK
++	select ARCH_REQUIRE_GPIOLIB
+ 	help
+ 	  Support for Atheros AR231x and Atheros AR531x based boards
+ 
diff --git a/target/linux/ath25/patches-4.4/108-ar2315_gpio.patch b/target/linux/ath25/patches-4.4/108-ar2315_gpio.patch
new file mode 100644
index 0000000..2165897
--- /dev/null
+++ b/target/linux/ath25/patches-4.4/108-ar2315_gpio.patch
@@ -0,0 +1,363 @@
+--- a/arch/mips/ath25/Kconfig
++++ b/arch/mips/ath25/Kconfig
+@@ -7,6 +7,7 @@ config SOC_AR5312
+ config SOC_AR2315
+ 	bool "Atheros AR2315+ SoC support"
+ 	depends on ATH25
++	select GPIO_AR2315
+ 	default y
+ 
+ config PCI_AR2315
+--- a/arch/mips/ath25/ar2315.c
++++ b/arch/mips/ath25/ar2315.c
+@@ -21,6 +21,8 @@
+ #include <linux/interrupt.h>
+ #include <linux/platform_device.h>
+ #include <linux/reboot.h>
++#include <linux/delay.h>
++#include <linux/gpio.h>
+ #include <asm/bootinfo.h>
+ #include <asm/reboot.h>
+ #include <asm/time.h>
+@@ -167,11 +169,42 @@ void __init ar2315_arch_init_irq(void)
+ 	ar2315_misc_irq_domain = domain;
+ }
+ 
++static struct resource ar2315_gpio_res[] = {
++	{
++		.name = "ar2315-gpio",
++		.flags = IORESOURCE_MEM,
++		.start = AR2315_RST_BASE + AR2315_GPIO,
++		.end = AR2315_RST_BASE + AR2315_GPIO + 0x10 - 1,
++	},
++	{
++		.name = "ar2315-gpio",
++		.flags = IORESOURCE_IRQ,
++	},
++	{
++		.name = "ar2315-gpio-irq-base",
++		.flags = IORESOURCE_IRQ,
++		.start = AR231X_GPIO_IRQ_BASE,
++		.end = AR231X_GPIO_IRQ_BASE,
++	}
++};
++
++static struct platform_device ar2315_gpio = {
++	.id = -1,
++	.name = "ar2315-gpio",
++	.resource = ar2315_gpio_res,
++	.num_resources = ARRAY_SIZE(ar2315_gpio_res)
++};
++
+ void __init ar2315_init_devices(void)
+ {
+ 	/* Find board configuration */
+ 	ath25_find_config(AR2315_SPI_READ_BASE, AR2315_SPI_READ_SIZE);
+ 
++	ar2315_gpio_res[1].start = irq_create_mapping(ar2315_misc_irq_domain,
++						      AR2315_MISC_IRQ_GPIO);
++	ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
++	platform_device_register(&ar2315_gpio);
++
+ 	ath25_add_wmac(0, AR2315_WLAN0_BASE, AR2315_IRQ_WLAN0);
+ }
+ 
+@@ -187,8 +220,8 @@ static void ar2315_restart(char *command
+ 	/* Cold reset does not work on the AR2315/6, use the GPIO reset bits
+ 	 * a workaround. Give it some time to attempt a gpio based hardware
+ 	 * reset (atheros reference design workaround) */
+-
+-	/* TODO: implement the GPIO reset workaround */
++	gpio_request_one(AR2315_RESET_GPIO, GPIOF_OUT_INIT_LOW, "Reset");
++	mdelay(100);
+ 
+ 	/* Some boards (e.g. Senao EOC-2610) don't implement the reset logic
+ 	 * workaround. Attempt to jump to the mips reset location -
+--- a/drivers/gpio/Kconfig
++++ b/drivers/gpio/Kconfig
+@@ -141,6 +141,13 @@ config GPIO_BRCMSTB
+ 	help
+ 	  Say yes here to enable GPIO support for Broadcom STB (BCM7XXX) SoCs.
+ 
++config GPIO_AR2315
++	bool "AR2315 SoC GPIO support"
++	default y if SOC_AR2315
++	depends on SOC_AR2315
++	help
++	  Say yes here to enable GPIO support for Atheros AR2315+ SoCs.
++
+ config GPIO_AR5312
+ 	bool "AR5312 SoC GPIO support"
+ 	default y if SOC_AR5312
+--- a/drivers/gpio/Makefile
++++ b/drivers/gpio/Makefile
+@@ -21,6 +21,7 @@ obj-$(CONFIG_GPIO_ADP5588)	+= gpio-adp55
+ obj-$(CONFIG_GPIO_ALTERA)  	+= gpio-altera.o
+ obj-$(CONFIG_GPIO_AMD8111)	+= gpio-amd8111.o
+ obj-$(CONFIG_GPIO_AMDPT)	+= gpio-amdpt.o
++obj-$(CONFIG_GPIO_AR2315)	+= gpio-ar2315.o
+ obj-$(CONFIG_GPIO_AR5312)	+= gpio-ar5312.o
+ obj-$(CONFIG_GPIO_ARIZONA)	+= gpio-arizona.o
+ obj-$(CONFIG_ATH79)		+= gpio-ath79.o
+--- /dev/null
++++ b/drivers/gpio/gpio-ar2315.c
+@@ -0,0 +1,233 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
++ * Copyright (C) 2006 FON Technology, SL.
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
++ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/gpio.h>
++#include <linux/irq.h>
++
++#define DRIVER_NAME	"ar2315-gpio"
++
++#define AR2315_GPIO_DI			0x0000
++#define AR2315_GPIO_DO			0x0008
++#define AR2315_GPIO_DIR			0x0010
++#define AR2315_GPIO_INT			0x0018
++
++#define AR2315_GPIO_DIR_M(x)		(1 << (x))	/* mask for i/o */
++#define AR2315_GPIO_DIR_O(x)		(1 << (x))	/* output */
++#define AR2315_GPIO_DIR_I(x)		(0)		/* input */
++
++#define AR2315_GPIO_INT_NUM_M		0x3F		/* mask for GPIO num */
++#define AR2315_GPIO_INT_TRIG(x)		((x) << 6)	/* interrupt trigger */
++#define AR2315_GPIO_INT_TRIG_M		(0x3 << 6)	/* mask for int trig */
++
++#define AR2315_GPIO_INT_TRIG_OFF	0	/* Triggerring off */
++#define AR2315_GPIO_INT_TRIG_LOW	1	/* Low Level Triggered */
++#define AR2315_GPIO_INT_TRIG_HIGH	2	/* High Level Triggered */
++#define AR2315_GPIO_INT_TRIG_EDGE	3	/* Edge Triggered */
++
++#define AR2315_GPIO_NUM		22
++
++static u32 ar2315_gpio_intmask;
++static u32 ar2315_gpio_intval;
++static unsigned ar2315_gpio_irq_base;
++static void __iomem *ar2315_mem;
++
++static inline u32 ar2315_gpio_reg_read(unsigned reg)
++{
++	return __raw_readl(ar2315_mem + reg);
++}
++
++static inline void ar2315_gpio_reg_write(unsigned reg, u32 val)
++{
++	__raw_writel(val, ar2315_mem + reg);
++}
++
++static inline void ar2315_gpio_reg_mask(unsigned reg, u32 mask, u32 val)
++{
++	ar2315_gpio_reg_write(reg, (ar2315_gpio_reg_read(reg) & ~mask) | val);
++}
++
++static void ar2315_gpio_irq_handler(unsigned irq, struct irq_desc *desc)
++{
++	u32 pend;
++	int bit = -1;
++
++	/* only do one gpio interrupt at a time */
++	pend = ar2315_gpio_reg_read(AR2315_GPIO_DI);
++	pend ^= ar2315_gpio_intval;
++	pend &= ar2315_gpio_intmask;
++
++	if (pend) {
++		bit = fls(pend) - 1;
++		pend &= ~(1 << bit);
++		ar2315_gpio_intval ^= (1 << bit);
++	}
++
++	/* Enable interrupt with edge detection */
++	if ((ar2315_gpio_reg_read(AR2315_GPIO_DIR) & AR2315_GPIO_DIR_M(bit)) !=
++	    AR2315_GPIO_DIR_I(bit))
++		return;
++
++	if (bit >= 0)
++		generic_handle_irq(ar2315_gpio_irq_base + bit);
++}
++
++static void ar2315_gpio_int_setup(unsigned gpio, int trig)
++{
++	u32 reg = ar2315_gpio_reg_read(AR2315_GPIO_INT);
++
++	reg &= ~(AR2315_GPIO_INT_NUM_M | AR2315_GPIO_INT_TRIG_M);
++	reg |= gpio | AR2315_GPIO_INT_TRIG(trig);
++	ar2315_gpio_reg_write(AR2315_GPIO_INT, reg);
++}
++
++static void ar2315_gpio_irq_unmask(struct irq_data *d)
++{
++	unsigned gpio = d->irq - ar2315_gpio_irq_base;
++	u32 dir = ar2315_gpio_reg_read(AR2315_GPIO_DIR);
++
++	/* Enable interrupt with edge detection */
++	if ((dir & AR2315_GPIO_DIR_M(gpio)) != AR2315_GPIO_DIR_I(gpio))
++		return;
++
++	ar2315_gpio_intmask |= (1 << gpio);
++	ar2315_gpio_int_setup(gpio, AR2315_GPIO_INT_TRIG_EDGE);
++}
++
++static void ar2315_gpio_irq_mask(struct irq_data *d)
++{
++	unsigned gpio = d->irq - ar2315_gpio_irq_base;
++
++	/* Disable interrupt */
++	ar2315_gpio_intmask &= ~(1 << gpio);
++	ar2315_gpio_int_setup(gpio, AR2315_GPIO_INT_TRIG_OFF);
++}
++
++static struct irq_chip ar2315_gpio_irq_chip = {
++	.name		= DRIVER_NAME,
++	.irq_unmask	= ar2315_gpio_irq_unmask,
++	.irq_mask	= ar2315_gpio_irq_mask,
++};
++
++static void ar2315_gpio_irq_init(unsigned irq)
++{
++	unsigned i;
++
++	ar2315_gpio_intval = ar2315_gpio_reg_read(AR2315_GPIO_DI);
++	for (i = 0; i < AR2315_GPIO_NUM; i++) {
++		unsigned _irq = ar2315_gpio_irq_base + i;
++
++		irq_set_chip_and_handler(_irq, &ar2315_gpio_irq_chip,
++					 handle_level_irq);
++	}
++	irq_set_chained_handler(irq, ar2315_gpio_irq_handler);
++}
++
++static int ar2315_gpio_get_val(struct gpio_chip *chip, unsigned gpio)
++{
++	return (ar2315_gpio_reg_read(AR2315_GPIO_DI) >> gpio) & 1;
++}
++
++static void ar2315_gpio_set_val(struct gpio_chip *chip, unsigned gpio, int val)
++{
++	u32 reg = ar2315_gpio_reg_read(AR2315_GPIO_DO);
++
++	reg = val ? reg | (1 << gpio) : reg & ~(1 << gpio);
++	ar2315_gpio_reg_write(AR2315_GPIO_DO, reg);
++}
++
++static int ar2315_gpio_dir_in(struct gpio_chip *chip, unsigned gpio)
++{
++	ar2315_gpio_reg_mask(AR2315_GPIO_DIR, 1 << gpio, 0);
++	return 0;
++}
++
++static int ar2315_gpio_dir_out(struct gpio_chip *chip, unsigned gpio, int val)
++{
++	ar2315_gpio_reg_mask(AR2315_GPIO_DIR, 0, 1 << gpio);
++	ar2315_gpio_set_val(chip, gpio, val);
++	return 0;
++}
++
++static int ar2315_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
++{
++	return ar2315_gpio_irq_base + gpio;
++}
++
++static struct gpio_chip ar2315_gpio_chip = {
++	.label			= DRIVER_NAME,
++	.direction_input	= ar2315_gpio_dir_in,
++	.direction_output	= ar2315_gpio_dir_out,
++	.set			= ar2315_gpio_set_val,
++	.get			= ar2315_gpio_get_val,
++	.to_irq			= ar2315_gpio_to_irq,
++	.base			= 0,
++	.ngpio			= AR2315_GPIO_NUM,
++};
++
++static int ar2315_gpio_probe(struct platform_device *pdev)
++{
++	struct device *dev = &pdev->dev;
++	struct resource *res;
++	unsigned irq;
++	int ret;
++
++	if (ar2315_mem)
++		return -EBUSY;
++
++	res = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
++					   "ar2315-gpio-irq-base");
++	if (!res) {
++		dev_err(dev, "not found GPIO IRQ base\n");
++		return -ENXIO;
++	}
++	ar2315_gpio_irq_base = res->start;
++
++	res = platform_get_resource_byname(pdev, IORESOURCE_IRQ, DRIVER_NAME);
++	if (!res) {
++		dev_err(dev, "not found IRQ number\n");
++		return -ENXIO;
++	}
++	irq = res->start;
++
++	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, DRIVER_NAME);
++	ar2315_mem = devm_ioremap_resource(dev, res);
++	if (IS_ERR(ar2315_mem))
++		return PTR_ERR(ar2315_mem);
++
++	ar2315_gpio_chip.dev = dev;
++	ret = gpiochip_add(&ar2315_gpio_chip);
++	if (ret) {
++		dev_err(dev, "failed to add gpiochip\n");
++		return ret;
++	}
++
++	ar2315_gpio_irq_init(irq);
++
++	return 0;
++}
++
++static struct platform_driver ar2315_gpio_driver = {
++	.probe = ar2315_gpio_probe,
++	.driver = {
++		.name = DRIVER_NAME,
++		.owner = THIS_MODULE,
++	}
++};
++
++static int __init ar2315_gpio_init(void)
++{
++	return platform_driver_register(&ar2315_gpio_driver);
++}
++subsys_initcall(ar2315_gpio_init);
+--- a/arch/mips/ath25/devices.h
++++ b/arch/mips/ath25/devices.h
+@@ -3,6 +3,11 @@
+ 
+ #include <linux/cpu.h>
+ 
++#define AR231X_GPIO_IRQ_BASE		0x30
++
++/* GPIO number for AR2315/16 reset issue workaround */
++#define AR2315_RESET_GPIO		5
++
+ #define ATH25_REG_MS(_val, _field)	(((_val) & _field##_M) >> _field##_S)
+ 
+ #define ATH25_IRQ_CPU_CLOCK	(MIPS_CPU_IRQ_BASE + 7)	/* C0_CAUSE: 0x8000 */
+--- a/arch/mips/ath25/ar2315_regs.h
++++ b/arch/mips/ath25/ar2315_regs.h
+@@ -315,6 +315,9 @@
+ #define AR2315_MEM_CFG_BANKADDR_BITS_M	0x00000018
+ #define AR2315_MEM_CFG_BANKADDR_BITS_S	3
+ 
++/* GPIO MMR base address */
++#define AR2315_GPIO			0x0088
++
+ /*
+  * Local Bus Interface Registers
+  */
diff --git a/target/linux/ath25/patches-4.4/110-ar2313_ethernet.patch b/target/linux/ath25/patches-4.4/110-ar2313_ethernet.patch
new file mode 100644
index 0000000..0efdb27
--- /dev/null
+++ b/target/linux/ath25/patches-4.4/110-ar2313_ethernet.patch
@@ -0,0 +1,1828 @@
+--- a/drivers/net/ethernet/atheros/Makefile
++++ b/drivers/net/ethernet/atheros/Makefile
+@@ -7,3 +7,4 @@ obj-$(CONFIG_ATL2) += atlx/
+ obj-$(CONFIG_ATL1E) += atl1e/
+ obj-$(CONFIG_ATL1C) += atl1c/
+ obj-$(CONFIG_ALX) += alx/
++obj-$(CONFIG_NET_AR231X) += ar231x/
+--- a/drivers/net/ethernet/atheros/Kconfig
++++ b/drivers/net/ethernet/atheros/Kconfig
+@@ -5,7 +5,7 @@
+ config NET_VENDOR_ATHEROS
+ 	bool "Atheros devices"
+ 	default y
+-	depends on PCI
++	depends on (PCI || ATH25)
+ 	---help---
+ 	  If you have a network (Ethernet) card belonging to this class, say Y.
+ 
+@@ -78,4 +78,10 @@ config ALX
+ 	  To compile this driver as a module, choose M here.  The module
+ 	  will be called alx.
+ 
++config NET_AR231X
++	tristate "Atheros AR231X built-in Ethernet support"
++	depends on ATH25
++	help
++	  Support for the AR231x/531x ethernet controller
++
+ endif # NET_VENDOR_ATHEROS
+--- /dev/null
++++ b/drivers/net/ethernet/atheros/ar231x/Makefile
+@@ -0,0 +1 @@
++obj-$(CONFIG_NET_AR231X) += ar231x.o
+--- /dev/null
++++ b/drivers/net/ethernet/atheros/ar231x/ar231x.c
+@@ -0,0 +1,1206 @@
++/*
++ * ar231x.c: Linux driver for the Atheros AR231x Ethernet device.
++ *
++ * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++ *
++ * Thanks to Atheros for providing hardware and documentation
++ * enabling me to write this driver.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * Additional credits:
++ * This code is taken from John Taylor's Sibyte driver and then
++ * modified for the AR2313.
++ */
++
++#include <linux/module.h>
++#include <linux/types.h>
++#include <linux/errno.h>
++#include <linux/ioport.h>
++#include <linux/netdevice.h>
++#include <linux/etherdevice.h>
++#include <linux/interrupt.h>
++#include <linux/skbuff.h>
++#include <linux/init.h>
++#include <linux/delay.h>
++#include <linux/mm.h>
++#include <linux/mii.h>
++#include <linux/phy.h>
++#include <linux/platform_device.h>
++#include <linux/io.h>
++
++#define AR2313_MTU                     1692
++#define AR2313_PRIOS                   1
++#define AR2313_QUEUES                  (2*AR2313_PRIOS)
++#define AR2313_DESCR_ENTRIES           64
++
++#ifndef min
++#define min(a, b)	(((a) < (b)) ? (a) : (b))
++#endif
++
++#ifndef SMP_CACHE_BYTES
++#define SMP_CACHE_BYTES	L1_CACHE_BYTES
++#endif
++
++#define AR2313_MBOX_SET_BIT  0x8
++
++#include "ar231x.h"
++
++/**
++ * New interrupt handler strategy:
++ *
++ * An old interrupt handler worked using the traditional method of
++ * replacing an skbuff with a new one when a packet arrives. However
++ * the rx rings do not need to contain a static number of buffer
++ * descriptors, thus it makes sense to move the memory allocation out
++ * of the main interrupt handler and do it in a bottom half handler
++ * and only allocate new buffers when the number of buffers in the
++ * ring is below a certain threshold. In order to avoid starving the
++ * NIC under heavy load it is however necessary to force allocation
++ * when hitting a minimum threshold. The strategy for alloction is as
++ * follows:
++ *
++ *     RX_LOW_BUF_THRES    - allocate buffers in the bottom half
++ *     RX_PANIC_LOW_THRES  - we are very low on buffers, allocate
++ *                           the buffers in the interrupt handler
++ *     RX_RING_THRES       - maximum number of buffers in the rx ring
++ *
++ * One advantagous side effect of this allocation approach is that the
++ * entire rx processing can be done without holding any spin lock
++ * since the rx rings and registers are totally independent of the tx
++ * ring and its registers.  This of course includes the kmalloc's of
++ * new skb's. Thus start_xmit can run in parallel with rx processing
++ * and the memory allocation on SMP systems.
++ *
++ * Note that running the skb reallocation in a bottom half opens up
++ * another can of races which needs to be handled properly. In
++ * particular it can happen that the interrupt handler tries to run
++ * the reallocation while the bottom half is either running on another
++ * CPU or was interrupted on the same CPU. To get around this the
++ * driver uses bitops to prevent the reallocation routines from being
++ * reentered.
++ *
++ * TX handling can also be done without holding any spin lock, wheee
++ * this is fun! since tx_csm is only written to by the interrupt
++ * handler.
++ */
++
++/**
++ * Threshold values for RX buffer allocation - the low water marks for
++ * when to start refilling the rings are set to 75% of the ring
++ * sizes. It seems to make sense to refill the rings entirely from the
++ * intrrupt handler once it gets below the panic threshold, that way
++ * we don't risk that the refilling is moved to another CPU when the
++ * one running the interrupt handler just got the slab code hot in its
++ * cache.
++ */
++#define RX_RING_SIZE		AR2313_DESCR_ENTRIES
++#define RX_PANIC_THRES	        (RX_RING_SIZE/4)
++#define RX_LOW_THRES	        ((3*RX_RING_SIZE)/4)
++#define CRC_LEN                 4
++#define RX_OFFSET               2
++
++#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
++#define VLAN_HDR                4
++#else
++#define VLAN_HDR                0
++#endif
++
++#define AR2313_BUFSIZE		(AR2313_MTU + VLAN_HDR + ETH_HLEN + CRC_LEN + \
++				 RX_OFFSET)
++
++#ifdef MODULE
++MODULE_LICENSE("GPL");
++MODULE_AUTHOR("Sameer Dekate <sdekate@arubanetworks.com>, Imre Kaloz <kaloz@openwrt.org>, Felix Fietkau <nbd@openwrt.org>");
++MODULE_DESCRIPTION("AR231x Ethernet driver");
++#endif
++
++#define virt_to_phys(x) ((u32)(x) & 0x1fffffff)
++
++/* prototypes */
++static void ar231x_halt(struct net_device *dev);
++static void rx_tasklet_func(unsigned long data);
++static void rx_tasklet_cleanup(struct net_device *dev);
++static void ar231x_multicast_list(struct net_device *dev);
++static void ar231x_tx_timeout(struct net_device *dev);
++
++static int ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum);
++static int ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
++				u16 value);
++static int ar231x_mdiobus_reset(struct mii_bus *bus);
++static int ar231x_mdiobus_probe(struct net_device *dev);
++static void ar231x_adjust_link(struct net_device *dev);
++
++#ifndef ERR
++#define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args)
++#endif
++
++#ifdef CONFIG_NET_POLL_CONTROLLER
++static void
++ar231x_netpoll(struct net_device *dev)
++{
++	unsigned long flags;
++
++	local_irq_save(flags);
++	ar231x_interrupt(dev->irq, dev);
++	local_irq_restore(flags);
++}
++#endif
++
++static const struct net_device_ops ar231x_ops = {
++	.ndo_open		= ar231x_open,
++	.ndo_stop		= ar231x_close,
++	.ndo_start_xmit		= ar231x_start_xmit,
++	.ndo_set_rx_mode	= ar231x_multicast_list,
++	.ndo_do_ioctl		= ar231x_ioctl,
++	.ndo_change_mtu		= eth_change_mtu,
++	.ndo_validate_addr	= eth_validate_addr,
++	.ndo_set_mac_address	= eth_mac_addr,
++	.ndo_tx_timeout		= ar231x_tx_timeout,
++#ifdef CONFIG_NET_POLL_CONTROLLER
++	.ndo_poll_controller	= ar231x_netpoll,
++#endif
++};
++
++static int ar231x_probe(struct platform_device *pdev)
++{
++	struct net_device *dev;
++	struct ar231x_private *sp;
++	struct resource *res;
++	unsigned long ar_eth_base;
++	char buf[64];
++
++	dev = alloc_etherdev(sizeof(struct ar231x_private));
++
++	if (dev == NULL) {
++		printk(KERN_ERR
++			   "ar231x: Unable to allocate net_device structure!\n");
++		return -ENOMEM;
++	}
++
++	platform_set_drvdata(pdev, dev);
++
++	sp = netdev_priv(dev);
++	sp->dev = dev;
++	sp->cfg = pdev->dev.platform_data;
++
++	sprintf(buf, "eth%d_membase", pdev->id);
++	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, buf);
++	if (!res)
++		return -ENODEV;
++
++	sp->link = 0;
++	ar_eth_base = res->start;
++
++	sprintf(buf, "eth%d_irq", pdev->id);
++	dev->irq = platform_get_irq_byname(pdev, buf);
++
++	spin_lock_init(&sp->lock);
++
++	dev->features |= NETIF_F_HIGHDMA;
++	dev->netdev_ops = &ar231x_ops;
++
++	tasklet_init(&sp->rx_tasklet, rx_tasklet_func, (unsigned long)dev);
++	tasklet_disable(&sp->rx_tasklet);
++
++	sp->eth_regs = ioremap_nocache(ar_eth_base, sizeof(*sp->eth_regs));
++	if (!sp->eth_regs) {
++		printk("Can't remap eth registers\n");
++		return -ENXIO;
++	}
++
++	/**
++	 * When there's only one MAC, PHY regs are typically on ENET0,
++	 * even though the MAC might be on ENET1.
++	 * So remap PHY regs separately.
++	 */
++	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "eth0_mii");
++	if (!res) {
++		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
++						   "eth1_mii");
++		if (!res)
++			return -ENODEV;
++	}
++	sp->phy_regs = ioremap_nocache(res->start, resource_size(res));
++	if (!sp->phy_regs) {
++		printk("Can't remap phy registers\n");
++		return -ENXIO;
++	}
++
++	sp->dma_regs = ioremap_nocache(ar_eth_base + 0x1000,
++				       sizeof(*sp->dma_regs));
++	if (!sp->dma_regs) {
++		printk("Can't remap DMA registers\n");
++		return -ENXIO;
++	}
++	dev->base_addr = ar_eth_base + 0x1000;
++
++	strncpy(sp->name, "Atheros AR231x", sizeof(sp->name) - 1);
++	sp->name[sizeof(sp->name) - 1] = '\0';
++	memcpy(dev->dev_addr, sp->cfg->macaddr, 6);
++
++	if (ar231x_init(dev)) {
++		/* ar231x_init() calls ar231x_init_cleanup() on error */
++		kfree(dev);
++		return -ENODEV;
++	}
++
++	if (register_netdev(dev)) {
++		printk("%s: register_netdev failed\n", __func__);
++		return -1;
++	}
++
++	printk("%s: %s: %pM, irq %d\n", dev->name, sp->name, dev->dev_addr,
++	       dev->irq);
++
++	sp->mii_bus = mdiobus_alloc();
++	if (sp->mii_bus == NULL)
++		return -1;
++
++	sp->mii_bus->priv = dev;
++	sp->mii_bus->read = ar231x_mdiobus_read;
++	sp->mii_bus->write = ar231x_mdiobus_write;
++	sp->mii_bus->reset = ar231x_mdiobus_reset;
++	sp->mii_bus->name = "ar231x_eth_mii";
++	snprintf(sp->mii_bus->id, MII_BUS_ID_SIZE, "%d", pdev->id);
++	sp->mii_bus->irq = kmalloc(sizeof(int), GFP_KERNEL);
++	*sp->mii_bus->irq = PHY_POLL;
++
++	mdiobus_register(sp->mii_bus);
++
++	if (ar231x_mdiobus_probe(dev) != 0) {
++		printk(KERN_ERR "%s: mdiobus_probe failed\n", dev->name);
++		rx_tasklet_cleanup(dev);
++		ar231x_init_cleanup(dev);
++		unregister_netdev(dev);
++		kfree(dev);
++		return -ENODEV;
++	}
++
++	/* start link poll timer */
++	ar231x_setup_timer(dev);
++
++	return 0;
++}
++
++static void ar231x_multicast_list(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	unsigned int filter;
++
++	filter = sp->eth_regs->mac_control;
++
++	if (dev->flags & IFF_PROMISC)
++		filter |= MAC_CONTROL_PR;
++	else
++		filter &= ~MAC_CONTROL_PR;
++	if ((dev->flags & IFF_ALLMULTI) || (netdev_mc_count(dev) > 0))
++		filter |= MAC_CONTROL_PM;
++	else
++		filter &= ~MAC_CONTROL_PM;
++
++	sp->eth_regs->mac_control = filter;
++}
++
++static void rx_tasklet_cleanup(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++
++	/**
++	 * Tasklet may be scheduled. Need to get it removed from the list
++	 * since we're about to free the struct.
++	 */
++
++	sp->unloading = 1;
++	tasklet_enable(&sp->rx_tasklet);
++	tasklet_kill(&sp->rx_tasklet);
++}
++
++static int ar231x_remove(struct platform_device *pdev)
++{
++	struct net_device *dev = platform_get_drvdata(pdev);
++	struct ar231x_private *sp = netdev_priv(dev);
++
++	rx_tasklet_cleanup(dev);
++	ar231x_init_cleanup(dev);
++	unregister_netdev(dev);
++	mdiobus_unregister(sp->mii_bus);
++	mdiobus_free(sp->mii_bus);
++	kfree(dev);
++	return 0;
++}
++
++/**
++ * Restart the AR2313 ethernet controller.
++ */
++static int ar231x_restart(struct net_device *dev)
++{
++	/* disable interrupts */
++	disable_irq(dev->irq);
++
++	/* stop mac */
++	ar231x_halt(dev);
++
++	/* initialize */
++	ar231x_init(dev);
++
++	/* enable interrupts */
++	enable_irq(dev->irq);
++
++	return 0;
++}
++
++static struct platform_driver ar231x_driver = {
++	.driver.name = "ar231x-eth",
++	.probe = ar231x_probe,
++	.remove = ar231x_remove,
++};
++
++module_platform_driver(ar231x_driver);
++
++static void ar231x_free_descriptors(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++
++	if (sp->rx_ring != NULL) {
++		kfree((void *)KSEG0ADDR(sp->rx_ring));
++		sp->rx_ring = NULL;
++		sp->tx_ring = NULL;
++	}
++}
++
++static int ar231x_allocate_descriptors(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	int size;
++	int j;
++	ar231x_descr_t *space;
++
++	if (sp->rx_ring != NULL) {
++		printk("%s: already done.\n", __func__);
++		return 0;
++	}
++
++	size = sizeof(ar231x_descr_t) * (AR2313_DESCR_ENTRIES * AR2313_QUEUES);
++	space = kmalloc(size, GFP_KERNEL);
++	if (space == NULL)
++		return 1;
++
++	/* invalidate caches */
++	dma_cache_inv((unsigned int)space, size);
++
++	/* now convert pointer to KSEG1 */
++	space = (ar231x_descr_t *)KSEG1ADDR(space);
++
++	memset((void *)space, 0, size);
++
++	sp->rx_ring = space;
++	space += AR2313_DESCR_ENTRIES;
++
++	sp->tx_ring = space;
++	space += AR2313_DESCR_ENTRIES;
++
++	/* Initialize the transmit Descriptors */
++	for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
++		ar231x_descr_t *td = &sp->tx_ring[j];
++
++		td->status = 0;
++		td->devcs = DMA_TX1_CHAINED;
++		td->addr = 0;
++		td->descr = virt_to_phys(&sp->tx_ring[DSC_NEXT(j)]);
++	}
++
++	return 0;
++}
++
++/**
++ * Generic cleanup handling data allocated during init. Used when the
++ * module is unloaded or if an error occurs during initialization
++ */
++static void ar231x_init_cleanup(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	struct sk_buff *skb;
++	int j;
++
++	ar231x_free_descriptors(dev);
++
++	if (sp->eth_regs)
++		iounmap((void *)sp->eth_regs);
++	if (sp->dma_regs)
++		iounmap((void *)sp->dma_regs);
++	if (sp->phy_regs)
++		iounmap((void *)sp->phy_regs);
++
++	if (sp->rx_skb) {
++		for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
++			skb = sp->rx_skb[j];
++			if (skb) {
++				sp->rx_skb[j] = NULL;
++				dev_kfree_skb(skb);
++			}
++		}
++		kfree(sp->rx_skb);
++		sp->rx_skb = NULL;
++	}
++
++	if (sp->tx_skb) {
++		for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
++			skb = sp->tx_skb[j];
++			if (skb) {
++				sp->tx_skb[j] = NULL;
++				dev_kfree_skb(skb);
++			}
++		}
++		kfree(sp->tx_skb);
++		sp->tx_skb = NULL;
++	}
++}
++
++static int ar231x_setup_timer(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++
++	init_timer(&sp->link_timer);
++
++	sp->link_timer.function = ar231x_link_timer_fn;
++	sp->link_timer.data = (int)dev;
++	sp->link_timer.expires = jiffies + HZ;
++
++	add_timer(&sp->link_timer);
++	return 0;
++}
++
++static void ar231x_link_timer_fn(unsigned long data)
++{
++	struct net_device *dev = (struct net_device *)data;
++	struct ar231x_private *sp = netdev_priv(dev);
++
++	/**
++	 * See if the link status changed.
++	 * This was needed to make sure we set the PHY to the
++	 * autonegotiated value of half or full duplex.
++	 */
++	ar231x_check_link(dev);
++
++	/**
++	 * Loop faster when we don't have link.
++	 * This was needed to speed up the AP bootstrap time.
++	 */
++	if (sp->link == 0)
++		mod_timer(&sp->link_timer, jiffies + HZ / 2);
++	else
++		mod_timer(&sp->link_timer, jiffies + LINK_TIMER);
++}
++
++static void ar231x_check_link(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	u16 phy_data;
++
++	phy_data = ar231x_mdiobus_read(sp->mii_bus, sp->phy, MII_BMSR);
++	if (sp->phy_data != phy_data) {
++		if (phy_data & BMSR_LSTATUS) {
++			/**
++			 * Link is present, ready link partner ability to
++			 * deterine duplexity.
++			 */
++			int duplex = 0;
++			u16 reg;
++
++			sp->link = 1;
++			reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy,
++						  MII_BMCR);
++			if (reg & BMCR_ANENABLE) {
++				/* auto neg enabled */
++				reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy,
++							  MII_LPA);
++				duplex = reg & (LPA_100FULL | LPA_10FULL) ?
++					 1 : 0;
++			} else {
++				/* no auto neg, just read duplex config */
++				duplex = (reg & BMCR_FULLDPLX) ? 1 : 0;
++			}
++
++			printk(KERN_INFO "%s: Configuring MAC for %s duplex\n",
++			       dev->name, (duplex) ? "full" : "half");
++
++			if (duplex) {
++				/* full duplex */
++				sp->eth_regs->mac_control =
++					(sp->eth_regs->mac_control |
++					 MAC_CONTROL_F) & ~MAC_CONTROL_DRO;
++			} else {
++				/* half duplex */
++				sp->eth_regs->mac_control =
++					(sp->eth_regs->mac_control |
++					 MAC_CONTROL_DRO) & ~MAC_CONTROL_F;
++			}
++		} else {
++			/* no link */
++			sp->link = 0;
++		}
++		sp->phy_data = phy_data;
++	}
++}
++
++static int ar231x_reset_reg(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	unsigned int ethsal, ethsah;
++	unsigned int flags;
++
++	sp->cfg->reset_set(sp->cfg->reset_mac);
++	mdelay(10);
++	sp->cfg->reset_clear(sp->cfg->reset_mac);
++	mdelay(10);
++	sp->cfg->reset_set(sp->cfg->reset_phy);
++	mdelay(10);
++	sp->cfg->reset_clear(sp->cfg->reset_phy);
++	mdelay(10);
++
++	sp->dma_regs->bus_mode = (DMA_BUS_MODE_SWR);
++	mdelay(10);
++	sp->dma_regs->bus_mode =
++		((32 << DMA_BUS_MODE_PBL_SHIFT) | DMA_BUS_MODE_BLE);
++
++	/* enable interrupts */
++	sp->dma_regs->intr_ena = DMA_STATUS_AIS | DMA_STATUS_NIS |
++				 DMA_STATUS_RI | DMA_STATUS_TI |
++				 DMA_STATUS_FBE;
++	sp->dma_regs->xmt_base = virt_to_phys(sp->tx_ring);
++	sp->dma_regs->rcv_base = virt_to_phys(sp->rx_ring);
++	sp->dma_regs->control =
++		(DMA_CONTROL_SR | DMA_CONTROL_ST | DMA_CONTROL_SF);
++
++	sp->eth_regs->flow_control = (FLOW_CONTROL_FCE);
++	sp->eth_regs->vlan_tag = (0x8100);
++
++	/* Enable Ethernet Interface */
++	flags = (MAC_CONTROL_TE |	/* transmit enable */
++			 MAC_CONTROL_PM |	/* pass mcast */
++			 MAC_CONTROL_F |	/* full duplex */
++			 MAC_CONTROL_HBD);	/* heart beat disabled */
++
++	if (dev->flags & IFF_PROMISC) {	/* set promiscuous mode */
++		flags |= MAC_CONTROL_PR;
++	}
++	sp->eth_regs->mac_control = flags;
++
++	/* Set all Ethernet station address registers to their initial values */
++	ethsah = (((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
++		 (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF);
++
++	ethsal = (((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
++		 (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
++		 (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
++		 (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF);
++
++	sp->eth_regs->mac_addr[0] = ethsah;
++	sp->eth_regs->mac_addr[1] = ethsal;
++
++	mdelay(10);
++
++	return 0;
++}
++
++static int ar231x_init(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	int ecode = 0;
++
++	/* Allocate descriptors */
++	if (ar231x_allocate_descriptors(dev)) {
++		printk("%s: %s: ar231x_allocate_descriptors failed\n",
++		       dev->name, __func__);
++		ecode = -EAGAIN;
++		goto init_error;
++	}
++
++	/* Get the memory for the skb rings */
++	if (sp->rx_skb == NULL) {
++		sp->rx_skb =
++			kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
++				GFP_KERNEL);
++		if (!(sp->rx_skb)) {
++			printk("%s: %s: rx_skb kmalloc failed\n",
++			       dev->name, __func__);
++			ecode = -EAGAIN;
++			goto init_error;
++		}
++	}
++	memset(sp->rx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
++
++	if (sp->tx_skb == NULL) {
++		sp->tx_skb =
++			kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
++				GFP_KERNEL);
++		if (!(sp->tx_skb)) {
++			printk("%s: %s: tx_skb kmalloc failed\n",
++			       dev->name, __func__);
++			ecode = -EAGAIN;
++			goto init_error;
++		}
++	}
++	memset(sp->tx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
++
++	/**
++	 * Set tx_csm before we start receiving interrupts, otherwise
++	 * the interrupt handler might think it is supposed to process
++	 * tx ints before we are up and running, which may cause a null
++	 * pointer access in the int handler.
++	 */
++	sp->rx_skbprd = 0;
++	sp->cur_rx = 0;
++	sp->tx_prd = 0;
++	sp->tx_csm = 0;
++
++	/* Zero the stats before starting the interface */
++	memset(&dev->stats, 0, sizeof(dev->stats));
++
++	/**
++	 * We load the ring here as there seem to be no way to tell the
++	 * firmware to wipe the ring without re-initializing it.
++	 */
++	ar231x_load_rx_ring(dev, RX_RING_SIZE);
++
++	/* Init hardware */
++	ar231x_reset_reg(dev);
++
++	/* Get the IRQ */
++	ecode = request_irq(dev->irq, &ar231x_interrupt, 0,
++			    dev->name, dev);
++	if (ecode) {
++		printk(KERN_WARNING "%s: %s: Requested IRQ %d is busy\n",
++		       dev->name, __func__, dev->irq);
++		goto init_error;
++	}
++
++	tasklet_enable(&sp->rx_tasklet);
++
++	return 0;
++
++init_error:
++	ar231x_init_cleanup(dev);
++	return ecode;
++}
++
++/**
++ * Load the rx ring.
++ *
++ * Loading rings is safe without holding the spin lock since this is
++ * done only before the device is enabled, thus no interrupts are
++ * generated and by the interrupt handler/tasklet handler.
++ */
++static void ar231x_load_rx_ring(struct net_device *dev, int nr_bufs)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	short i, idx;
++
++	idx = sp->rx_skbprd;
++
++	for (i = 0; i < nr_bufs; i++) {
++		struct sk_buff *skb;
++		ar231x_descr_t *rd;
++
++		if (sp->rx_skb[idx])
++			break;
++
++		skb = netdev_alloc_skb_ip_align(dev, AR2313_BUFSIZE);
++		if (!skb) {
++			printk("\n\n\n\n %s: No memory in system\n\n\n\n",
++			       __func__);
++			break;
++		}
++
++		/* Make sure IP header starts on a fresh cache line */
++		skb->dev = dev;
++		sp->rx_skb[idx] = skb;
++
++		rd = (ar231x_descr_t *)&sp->rx_ring[idx];
++
++		/* initialize dma descriptor */
++		rd->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
++					 DMA_RX1_CHAINED);
++		rd->addr = virt_to_phys(skb->data);
++		rd->descr = virt_to_phys(&sp->rx_ring[DSC_NEXT(idx)]);
++		rd->status = DMA_RX_OWN;
++
++		idx = DSC_NEXT(idx);
++	}
++
++	if (i)
++		sp->rx_skbprd = idx;
++}
++
++#define AR2313_MAX_PKTS_PER_CALL        64
++
++static int ar231x_rx_int(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	struct sk_buff *skb, *skb_new;
++	ar231x_descr_t *rxdesc;
++	unsigned int status;
++	u32 idx;
++	int pkts = 0;
++	int rval;
++
++	idx = sp->cur_rx;
++
++	/* process at most the entire ring and then wait for another int */
++	while (1) {
++		rxdesc = &sp->rx_ring[idx];
++		status = rxdesc->status;
++
++		if (status & DMA_RX_OWN) {
++			/* SiByte owns descriptor or descr not yet filled in */
++			rval = 0;
++			break;
++		}
++
++		if (++pkts > AR2313_MAX_PKTS_PER_CALL) {
++			rval = 1;
++			break;
++		}
++
++		if ((status & DMA_RX_ERROR) && !(status & DMA_RX_LONG)) {
++			dev->stats.rx_errors++;
++			dev->stats.rx_dropped++;
++
++			/* add statistics counters */
++			if (status & DMA_RX_ERR_CRC)
++				dev->stats.rx_crc_errors++;
++			if (status & DMA_RX_ERR_COL)
++				dev->stats.rx_over_errors++;
++			if (status & DMA_RX_ERR_LENGTH)
++				dev->stats.rx_length_errors++;
++			if (status & DMA_RX_ERR_RUNT)
++				dev->stats.rx_over_errors++;
++			if (status & DMA_RX_ERR_DESC)
++				dev->stats.rx_over_errors++;
++
++		} else {
++			/* alloc new buffer. */
++			skb_new = netdev_alloc_skb_ip_align(dev,
++							    AR2313_BUFSIZE);
++			if (skb_new != NULL) {
++				skb = sp->rx_skb[idx];
++				/* set skb */
++				skb_put(skb, ((status >> DMA_RX_LEN_SHIFT) &
++					0x3fff) - CRC_LEN);
++
++				dev->stats.rx_bytes += skb->len;
++				skb->protocol = eth_type_trans(skb, dev);
++				/* pass the packet to upper layers */
++				netif_rx(skb);
++
++				skb_new->dev = dev;
++				/* reset descriptor's curr_addr */
++				rxdesc->addr = virt_to_phys(skb_new->data);
++
++				dev->stats.rx_packets++;
++				sp->rx_skb[idx] = skb_new;
++			} else {
++				dev->stats.rx_dropped++;
++			}
++		}
++
++		rxdesc->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
++						 DMA_RX1_CHAINED);
++		rxdesc->status = DMA_RX_OWN;
++
++		idx = DSC_NEXT(idx);
++	}
++
++	sp->cur_rx = idx;
++
++	return rval;
++}
++
++static void ar231x_tx_int(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	u32 idx;
++	struct sk_buff *skb;
++	ar231x_descr_t *txdesc;
++	unsigned int status = 0;
++
++	idx = sp->tx_csm;
++
++	while (idx != sp->tx_prd) {
++		txdesc = &sp->tx_ring[idx];
++		status = txdesc->status;
++
++		if (status & DMA_TX_OWN) {
++			/* ar231x dma still owns descr */
++			break;
++		}
++		/* done with this descriptor */
++		dma_unmap_single(NULL, txdesc->addr,
++				 txdesc->devcs & DMA_TX1_BSIZE_MASK,
++				 DMA_TO_DEVICE);
++		txdesc->status = 0;
++
++		if (status & DMA_TX_ERROR) {
++			dev->stats.tx_errors++;
++			dev->stats.tx_dropped++;
++			if (status & DMA_TX_ERR_UNDER)
++				dev->stats.tx_fifo_errors++;
++			if (status & DMA_TX_ERR_HB)
++				dev->stats.tx_heartbeat_errors++;
++			if (status & (DMA_TX_ERR_LOSS | DMA_TX_ERR_LINK))
++				dev->stats.tx_carrier_errors++;
++			if (status & (DMA_TX_ERR_LATE | DMA_TX_ERR_COL |
++			    DMA_TX_ERR_JABBER | DMA_TX_ERR_DEFER))
++				dev->stats.tx_aborted_errors++;
++		} else {
++			/* transmit OK */
++			dev->stats.tx_packets++;
++		}
++
++		skb = sp->tx_skb[idx];
++		sp->tx_skb[idx] = NULL;
++		idx = DSC_NEXT(idx);
++		dev->stats.tx_bytes += skb->len;
++		dev_kfree_skb_irq(skb);
++	}
++
++	sp->tx_csm = idx;
++}
++
++static void rx_tasklet_func(unsigned long data)
++{
++	struct net_device *dev = (struct net_device *)data;
++	struct ar231x_private *sp = netdev_priv(dev);
++
++	if (sp->unloading)
++		return;
++
++	if (ar231x_rx_int(dev)) {
++		tasklet_hi_schedule(&sp->rx_tasklet);
++	} else {
++		unsigned long flags;
++
++		spin_lock_irqsave(&sp->lock, flags);
++		sp->dma_regs->intr_ena |= DMA_STATUS_RI;
++		spin_unlock_irqrestore(&sp->lock, flags);
++	}
++}
++
++static void rx_schedule(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++
++	sp->dma_regs->intr_ena &= ~DMA_STATUS_RI;
++
++	tasklet_hi_schedule(&sp->rx_tasklet);
++}
++
++static irqreturn_t ar231x_interrupt(int irq, void *dev_id)
++{
++	struct net_device *dev = (struct net_device *)dev_id;
++	struct ar231x_private *sp = netdev_priv(dev);
++	unsigned int status, enabled;
++
++	/* clear interrupt */
++	/* Don't clear RI bit if currently disabled */
++	status = sp->dma_regs->status;
++	enabled = sp->dma_regs->intr_ena;
++	sp->dma_regs->status = status & enabled;
++
++	if (status & DMA_STATUS_NIS) {
++		/* normal status */
++		/**
++		 * Don't schedule rx processing if interrupt
++		 * is already disabled.
++		 */
++		if (status & enabled & DMA_STATUS_RI) {
++			/* receive interrupt */
++			rx_schedule(dev);
++		}
++		if (status & DMA_STATUS_TI) {
++			/* transmit interrupt */
++			ar231x_tx_int(dev);
++		}
++	}
++
++	/* abnormal status */
++	if (status & (DMA_STATUS_FBE | DMA_STATUS_TPS))
++		ar231x_restart(dev);
++
++	return IRQ_HANDLED;
++}
++
++static int ar231x_open(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	unsigned int ethsal, ethsah;
++
++	/* reset the hardware, in case the MAC address changed */
++	ethsah = (((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
++		 (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF);
++
++	ethsal = (((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
++		 (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
++		 (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
++		 (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF);
++
++	sp->eth_regs->mac_addr[0] = ethsah;
++	sp->eth_regs->mac_addr[1] = ethsal;
++
++	mdelay(10);
++
++	dev->mtu = 1500;
++	netif_start_queue(dev);
++
++	sp->eth_regs->mac_control |= MAC_CONTROL_RE;
++
++	return 0;
++}
++
++static void ar231x_tx_timeout(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	unsigned long flags;
++
++	spin_lock_irqsave(&sp->lock, flags);
++	ar231x_restart(dev);
++	spin_unlock_irqrestore(&sp->lock, flags);
++}
++
++static void ar231x_halt(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	int j;
++
++	tasklet_disable(&sp->rx_tasklet);
++
++	/* kill the MAC */
++	sp->eth_regs->mac_control &= ~(MAC_CONTROL_RE |	/* disable Receives */
++				       MAC_CONTROL_TE);	/* disable Transmits */
++	/* stop dma */
++	sp->dma_regs->control = 0;
++	sp->dma_regs->bus_mode = DMA_BUS_MODE_SWR;
++
++	/* place phy and MAC in reset */
++	sp->cfg->reset_set(sp->cfg->reset_mac);
++	sp->cfg->reset_set(sp->cfg->reset_phy);
++
++	/* free buffers on tx ring */
++	for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
++		struct sk_buff *skb;
++		ar231x_descr_t *txdesc;
++
++		txdesc = &sp->tx_ring[j];
++		txdesc->descr = 0;
++
++		skb = sp->tx_skb[j];
++		if (skb) {
++			dev_kfree_skb(skb);
++			sp->tx_skb[j] = NULL;
++		}
++	}
++}
++
++/**
++ * close should do nothing. Here's why. It's called when
++ * 'ifconfig bond0 down' is run. If it calls free_irq then
++ * the irq is gone forever ! When bond0 is made 'up' again,
++ * the ar231x_open () does not call request_irq (). Worse,
++ * the call to ar231x_halt() generates a WDOG reset due to
++ * the write to reset register and the box reboots.
++ * Commenting this out is good since it allows the
++ * system to resume when bond0 is made up again.
++ */
++static int ar231x_close(struct net_device *dev)
++{
++#if 0
++	/* Disable interrupts */
++	disable_irq(dev->irq);
++
++	/**
++	 * Without (or before) releasing irq and stopping hardware, this
++	 * is an absolute non-sense, by the way. It will be reset instantly
++	 * by the first irq.
++	 */
++	netif_stop_queue(dev);
++
++	/* stop the MAC and DMA engines */
++	ar231x_halt(dev);
++
++	/* release the interrupt */
++	free_irq(dev->irq, dev);
++
++#endif
++	return 0;
++}
++
++static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	ar231x_descr_t *td;
++	u32 idx;
++
++	idx = sp->tx_prd;
++	td = &sp->tx_ring[idx];
++
++	if (td->status & DMA_TX_OWN) {
++		/* free skbuf and lie to the caller that we sent it out */
++		dev->stats.tx_dropped++;
++		dev_kfree_skb(skb);
++
++		/* restart transmitter in case locked */
++		sp->dma_regs->xmt_poll = 0;
++		return 0;
++	}
++
++	/* Setup the transmit descriptor. */
++	td->devcs = ((skb->len << DMA_TX1_BSIZE_SHIFT) |
++				 (DMA_TX1_LS | DMA_TX1_IC | DMA_TX1_CHAINED));
++	td->addr = dma_map_single(NULL, skb->data, skb->len, DMA_TO_DEVICE);
++	td->status = DMA_TX_OWN;
++
++	/* kick transmitter last */
++	sp->dma_regs->xmt_poll = 0;
++
++	sp->tx_skb[idx] = skb;
++	idx = DSC_NEXT(idx);
++	sp->tx_prd = idx;
++
++	return 0;
++}
++
++static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++
++	switch (cmd) {
++	case SIOCGMIIPHY:
++	case SIOCGMIIREG:
++	case SIOCSMIIREG:
++		return phy_mii_ioctl(sp->phy_dev, ifr, cmd);
++
++	default:
++		break;
++	}
++
++	return -EOPNOTSUPP;
++}
++
++static void ar231x_adjust_link(struct net_device *dev)
++{
++	struct ar231x_private *sp = netdev_priv(dev);
++	unsigned int mc;
++
++	if (!sp->phy_dev->link)
++		return;
++
++	if (sp->phy_dev->duplex != sp->oldduplex) {
++		mc = readl(&sp->eth_regs->mac_control);
++		mc &= ~(MAC_CONTROL_F | MAC_CONTROL_DRO);
++		if (sp->phy_dev->duplex)
++			mc |= MAC_CONTROL_F;
++		else
++			mc |= MAC_CONTROL_DRO;
++		writel(mc, &sp->eth_regs->mac_control);
++		sp->oldduplex = sp->phy_dev->duplex;
++	}
++}
++
++#define MII_ADDR(phy, reg) \
++	((reg << MII_ADDR_REG_SHIFT) | (phy << MII_ADDR_PHY_SHIFT))
++
++static int
++ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
++{
++	struct net_device *const dev = bus->priv;
++	struct ar231x_private *sp = netdev_priv(dev);
++	volatile MII *ethernet = sp->phy_regs;
++
++	ethernet->mii_addr = MII_ADDR(phy_addr, regnum);
++	while (ethernet->mii_addr & MII_ADDR_BUSY)
++		;
++	return ethernet->mii_data >> MII_DATA_SHIFT;
++}
++
++static int
++ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, u16 value)
++{
++	struct net_device *const dev = bus->priv;
++	struct ar231x_private *sp = netdev_priv(dev);
++	volatile MII *ethernet = sp->phy_regs;
++
++	while (ethernet->mii_addr & MII_ADDR_BUSY)
++		;
++	ethernet->mii_data = value << MII_DATA_SHIFT;
++	ethernet->mii_addr = MII_ADDR(phy_addr, regnum) | MII_ADDR_WRITE;
++
++	return 0;
++}
++
++static int ar231x_mdiobus_reset(struct mii_bus *bus)
++{
++	struct net_device *const dev = bus->priv;
++
++	ar231x_reset_reg(dev);
++
++	return 0;
++}
++
++static int ar231x_mdiobus_probe(struct net_device *dev)
++{
++	struct ar231x_private *const sp = netdev_priv(dev);
++	struct phy_device *phydev = NULL;
++	int phy_addr;
++
++	/* find the first (lowest address) PHY on the current MAC's MII bus */
++	for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++)
++		if (sp->mii_bus->phy_map[phy_addr]) {
++			phydev = sp->mii_bus->phy_map[phy_addr];
++			sp->phy = phy_addr;
++			break; /* break out with first one found */
++		}
++
++	if (!phydev) {
++		printk(KERN_ERR "ar231x: %s: no PHY found\n", dev->name);
++		return -1;
++	}
++
++	/* now we are supposed to have a proper phydev, to attach to... */
++	BUG_ON(!phydev);
++	BUG_ON(phydev->attached_dev);
++
++	phydev = phy_connect(dev, dev_name(&phydev->dev), &ar231x_adjust_link,
++			     PHY_INTERFACE_MODE_MII);
++
++	if (IS_ERR(phydev)) {
++		printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
++		return PTR_ERR(phydev);
++	}
++
++	/* mask with MAC supported features */
++	phydev->supported &= (SUPPORTED_10baseT_Half
++		| SUPPORTED_10baseT_Full
++		| SUPPORTED_100baseT_Half
++		| SUPPORTED_100baseT_Full
++		| SUPPORTED_Autoneg
++		/* | SUPPORTED_Pause | SUPPORTED_Asym_Pause */
++		| SUPPORTED_MII
++		| SUPPORTED_TP);
++
++	phydev->advertising = phydev->supported;
++
++	sp->oldduplex = -1;
++	sp->phy_dev = phydev;
++
++	printk(KERN_INFO "%s: attached PHY driver [%s] (mii_bus:phy_addr=%s)\n",
++	       dev->name, phydev->drv->name, dev_name(&phydev->dev));
++
++	return 0;
++}
++
+--- /dev/null
++++ b/drivers/net/ethernet/atheros/ar231x/ar231x.h
+@@ -0,0 +1,288 @@
++/*
++ * ar231x.h: Linux driver for the Atheros AR231x Ethernet device.
++ *
++ * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++ *
++ * Thanks to Atheros for providing hardware and documentation
++ * enabling me to write this driver.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ */
++
++#ifndef _AR2313_H_
++#define _AR2313_H_
++
++#include <linux/interrupt.h>
++#include <generated/autoconf.h>
++#include <linux/bitops.h>
++#include <ath25_platform.h>
++
++/* probe link timer - 5 secs */
++#define LINK_TIMER    (5*HZ)
++
++#define IS_DMA_TX_INT(X)   (((X) & (DMA_STATUS_TI)) != 0)
++#define IS_DMA_RX_INT(X)   (((X) & (DMA_STATUS_RI)) != 0)
++#define IS_DRIVER_OWNED(X) (((X) & (DMA_TX_OWN))    == 0)
++
++#define AR2313_TX_TIMEOUT (HZ/4)
++
++/* Rings */
++#define DSC_RING_ENTRIES_SIZE	(AR2313_DESCR_ENTRIES * sizeof(struct desc))
++#define DSC_NEXT(idx)	        ((idx + 1) & (AR2313_DESCR_ENTRIES - 1))
++
++#define AR2313_MBGET		2
++#define AR2313_MBSET		3
++#define AR2313_PCI_RECONFIG	4
++#define AR2313_PCI_DUMP		5
++#define AR2313_TEST_PANIC	6
++#define AR2313_TEST_NULLPTR	7
++#define AR2313_READ_DATA	8
++#define AR2313_WRITE_DATA	9
++#define AR2313_GET_VERSION	10
++#define AR2313_TEST_HANG	11
++#define AR2313_SYNC		12
++
++#define DMA_RX_ERR_CRC		BIT(1)
++#define DMA_RX_ERR_DRIB		BIT(2)
++#define DMA_RX_ERR_MII		BIT(3)
++#define DMA_RX_EV2		BIT(5)
++#define DMA_RX_ERR_COL		BIT(6)
++#define DMA_RX_LONG		BIT(7)
++#define DMA_RX_LS		BIT(8)	/* last descriptor */
++#define DMA_RX_FS		BIT(9)	/* first descriptor */
++#define DMA_RX_MF		BIT(10)	/* multicast frame */
++#define DMA_RX_ERR_RUNT		BIT(11)	/* runt frame */
++#define DMA_RX_ERR_LENGTH	BIT(12)	/* length error */
++#define DMA_RX_ERR_DESC		BIT(14)	/* descriptor error */
++#define DMA_RX_ERROR		BIT(15)	/* error summary */
++#define DMA_RX_LEN_MASK		0x3fff0000
++#define DMA_RX_LEN_SHIFT	16
++#define DMA_RX_FILT		BIT(30)
++#define DMA_RX_OWN		BIT(31)	/* desc owned by DMA controller */
++
++#define DMA_RX1_BSIZE_MASK	0x000007ff
++#define DMA_RX1_BSIZE_SHIFT	0
++#define DMA_RX1_CHAINED		BIT(24)
++#define DMA_RX1_RER		BIT(25)
++
++#define DMA_TX_ERR_UNDER	BIT(1)	/* underflow error */
++#define DMA_TX_ERR_DEFER	BIT(2)	/* excessive deferral */
++#define DMA_TX_COL_MASK		0x78
++#define DMA_TX_COL_SHIFT	3
++#define DMA_TX_ERR_HB		BIT(7)	/* hearbeat failure */
++#define DMA_TX_ERR_COL		BIT(8)	/* excessive collisions */
++#define DMA_TX_ERR_LATE		BIT(9)	/* late collision */
++#define DMA_TX_ERR_LINK		BIT(10)	/* no carrier */
++#define DMA_TX_ERR_LOSS		BIT(11)	/* loss of carrier */
++#define DMA_TX_ERR_JABBER	BIT(14)	/* transmit jabber timeout */
++#define DMA_TX_ERROR		BIT(15)	/* frame aborted */
++#define DMA_TX_OWN		BIT(31)	/* descr owned by DMA controller */
++
++#define DMA_TX1_BSIZE_MASK	0x000007ff
++#define DMA_TX1_BSIZE_SHIFT	0
++#define DMA_TX1_CHAINED		BIT(24)	/* chained descriptors */
++#define DMA_TX1_TER		BIT(25)	/* transmit end of ring */
++#define DMA_TX1_FS		BIT(29)	/* first segment */
++#define DMA_TX1_LS		BIT(30)	/* last segment */
++#define DMA_TX1_IC		BIT(31)	/* interrupt on completion */
++
++#define RCVPKT_LENGTH(X)	(X  >> 16)	/* Received pkt Length */
++
++#define MAC_CONTROL_RE		BIT(2)	/* receive enable */
++#define MAC_CONTROL_TE		BIT(3)	/* transmit enable */
++#define MAC_CONTROL_DC		BIT(5)	/* Deferral check */
++#define MAC_CONTROL_ASTP	BIT(8)	/* Auto pad strip */
++#define MAC_CONTROL_DRTY	BIT(10)	/* Disable retry */
++#define MAC_CONTROL_DBF		BIT(11)	/* Disable bcast frames */
++#define MAC_CONTROL_LCC		BIT(12)	/* late collision ctrl */
++#define MAC_CONTROL_HP		BIT(13)	/* Hash Perfect filtering */
++#define MAC_CONTROL_HASH	BIT(14)	/* Unicast hash filtering */
++#define MAC_CONTROL_HO		BIT(15)	/* Hash only filtering */
++#define MAC_CONTROL_PB		BIT(16)	/* Pass Bad frames */
++#define MAC_CONTROL_IF		BIT(17)	/* Inverse filtering */
++#define MAC_CONTROL_PR		BIT(18)	/* promis mode (valid frames only) */
++#define MAC_CONTROL_PM		BIT(19)	/* pass multicast */
++#define MAC_CONTROL_F		BIT(20)	/* full-duplex */
++#define MAC_CONTROL_DRO		BIT(23)	/* Disable Receive Own */
++#define MAC_CONTROL_HBD		BIT(28)	/* heart-beat disabled (MUST BE SET) */
++#define MAC_CONTROL_BLE		BIT(30)	/* big endian mode */
++#define MAC_CONTROL_RA		BIT(31)	/* rcv all (valid and invalid frames) */
++
++#define MII_ADDR_BUSY		BIT(0)
++#define MII_ADDR_WRITE		BIT(1)
++#define MII_ADDR_REG_SHIFT	6
++#define MII_ADDR_PHY_SHIFT	11
++#define MII_DATA_SHIFT		0
++
++#define FLOW_CONTROL_FCE	BIT(1)
++
++#define DMA_BUS_MODE_SWR	BIT(0)	/* software reset */
++#define DMA_BUS_MODE_BLE	BIT(7)	/* big endian mode */
++#define DMA_BUS_MODE_PBL_SHIFT	8	/* programmable burst length 32 */
++#define DMA_BUS_MODE_DBO	BIT(20)	/* big-endian descriptors */
++
++#define DMA_STATUS_TI		BIT(0)	/* transmit interrupt */
++#define DMA_STATUS_TPS		BIT(1)	/* transmit process stopped */
++#define DMA_STATUS_TU		BIT(2)	/* transmit buffer unavailable */
++#define DMA_STATUS_TJT		BIT(3)	/* transmit buffer timeout */
++#define DMA_STATUS_UNF		BIT(5)	/* transmit underflow */
++#define DMA_STATUS_RI		BIT(6)	/* receive interrupt */
++#define DMA_STATUS_RU		BIT(7)	/* receive buffer unavailable */
++#define DMA_STATUS_RPS		BIT(8)	/* receive process stopped */
++#define DMA_STATUS_ETI		BIT(10)	/* early transmit interrupt */
++#define DMA_STATUS_FBE		BIT(13)	/* fatal bus interrupt */
++#define DMA_STATUS_ERI		BIT(14)	/* early receive interrupt */
++#define DMA_STATUS_AIS		BIT(15)	/* abnormal interrupt summary */
++#define DMA_STATUS_NIS		BIT(16)	/* normal interrupt summary */
++#define DMA_STATUS_RS_SHIFT	17	/* receive process state */
++#define DMA_STATUS_TS_SHIFT	20	/* transmit process state */
++#define DMA_STATUS_EB_SHIFT	23	/* error bits */
++
++#define DMA_CONTROL_SR		BIT(1)	/* start receive */
++#define DMA_CONTROL_ST		BIT(13)	/* start transmit */
++#define DMA_CONTROL_SF		BIT(21)	/* store and forward */
++
++typedef struct {
++	volatile unsigned int status;	/* OWN, Device control and status. */
++	volatile unsigned int devcs;	/* pkt Control bits + Length */
++	volatile unsigned int addr;	/* Current Address. */
++	volatile unsigned int descr;	/* Next descriptor in chain. */
++} ar231x_descr_t;
++
++/**
++ * New Combo structure for Both Eth0 AND eth1
++ *
++ * Don't directly access MII related regs since phy chip could be actually
++ * connected to another ethernet block.
++ */
++typedef struct {
++	volatile unsigned int mac_control;	/* 0x00 */
++	volatile unsigned int mac_addr[2];	/* 0x04 - 0x08 */
++	volatile unsigned int mcast_table[2];	/* 0x0c - 0x10 */
++	volatile unsigned int __mii_addr;	/* 0x14 */
++	volatile unsigned int __mii_data;	/* 0x18 */
++	volatile unsigned int flow_control;	/* 0x1c */
++	volatile unsigned int vlan_tag;	/* 0x20 */
++	volatile unsigned int pad[7];	/* 0x24 - 0x3c */
++	volatile unsigned int ucast_table[8];	/* 0x40-0x5c */
++} ETHERNET_STRUCT;
++
++typedef struct {
++	volatile unsigned int mii_addr;
++	volatile unsigned int mii_data;
++} MII;
++
++/********************************************************************
++ * Interrupt controller
++ ********************************************************************/
++
++typedef struct {
++	volatile unsigned int wdog_control;	/* 0x08 */
++	volatile unsigned int wdog_timer;	/* 0x0c */
++	volatile unsigned int misc_status;	/* 0x10 */
++	volatile unsigned int misc_mask;	/* 0x14 */
++	volatile unsigned int global_status;	/* 0x18 */
++	volatile unsigned int reserved;	/* 0x1c */
++	volatile unsigned int reset_control;	/* 0x20 */
++} INTERRUPT;
++
++/********************************************************************
++ * DMA controller
++ ********************************************************************/
++typedef struct {
++	volatile unsigned int bus_mode;	/* 0x00 (CSR0) */
++	volatile unsigned int xmt_poll;	/* 0x04 (CSR1) */
++	volatile unsigned int rcv_poll;	/* 0x08 (CSR2) */
++	volatile unsigned int rcv_base;	/* 0x0c (CSR3) */
++	volatile unsigned int xmt_base;	/* 0x10 (CSR4) */
++	volatile unsigned int status;	/* 0x14 (CSR5) */
++	volatile unsigned int control;	/* 0x18 (CSR6) */
++	volatile unsigned int intr_ena;	/* 0x1c (CSR7) */
++	volatile unsigned int rcv_missed;	/* 0x20 (CSR8) */
++	volatile unsigned int reserved[11];	/* 0x24-0x4c (CSR9-19) */
++	volatile unsigned int cur_tx_buf_addr;	/* 0x50 (CSR20) */
++	volatile unsigned int cur_rx_buf_addr;	/* 0x50 (CSR21) */
++} DMA;
++
++/**
++ * Struct private for the Sibyte.
++ *
++ * Elements are grouped so variables used by the tx handling goes
++ * together, and will go into the same cache lines etc. in order to
++ * avoid cache line contention between the rx and tx handling on SMP.
++ *
++ * Frequently accessed variables are put at the beginning of the
++ * struct to help the compiler generate better/shorter code.
++ */
++struct ar231x_private {
++	struct net_device *dev;
++	int version;
++	u32 mb[2];
++
++	volatile MII *phy_regs;
++	volatile ETHERNET_STRUCT *eth_regs;
++	volatile DMA *dma_regs;
++	struct ar231x_eth *cfg;
++
++	spinlock_t lock;			/* Serialise access to device */
++
++	/* RX and TX descriptors, must be adjacent */
++	ar231x_descr_t *rx_ring;
++	ar231x_descr_t *tx_ring;
++
++	struct sk_buff **rx_skb;
++	struct sk_buff **tx_skb;
++
++	/* RX elements */
++	u32 rx_skbprd;
++	u32 cur_rx;
++
++	/* TX elements */
++	u32 tx_prd;
++	u32 tx_csm;
++
++	/* Misc elements */
++	char name[48];
++	struct {
++		u32 address;
++		u32 length;
++		char *mapping;
++	} desc;
++
++	struct timer_list link_timer;
++	unsigned short phy;		/* merlot phy = 1, samsung phy = 0x1f */
++	unsigned short mac;
++	unsigned short link;		/* 0 - link down, 1 - link up */
++	u16 phy_data;
++
++	struct tasklet_struct rx_tasklet;
++	int unloading;
++
++	struct phy_device *phy_dev;
++	struct mii_bus *mii_bus;
++	int oldduplex;
++};
++
++/* Prototypes */
++static int ar231x_init(struct net_device *dev);
++#ifdef TX_TIMEOUT
++static void ar231x_tx_timeout(struct net_device *dev);
++#endif
++static int ar231x_restart(struct net_device *dev);
++static void ar231x_load_rx_ring(struct net_device *dev, int bufs);
++static irqreturn_t ar231x_interrupt(int irq, void *dev_id);
++static int ar231x_open(struct net_device *dev);
++static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev);
++static int ar231x_close(struct net_device *dev);
++static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd);
++static void ar231x_init_cleanup(struct net_device *dev);
++static int ar231x_setup_timer(struct net_device *dev);
++static void ar231x_link_timer_fn(unsigned long data);
++static void ar231x_check_link(struct net_device *dev);
++
++#endif	/* _AR2313_H_ */
+--- a/arch/mips/ath25/ar2315_regs.h
++++ b/arch/mips/ath25/ar2315_regs.h
+@@ -57,6 +57,9 @@
+ #define AR2315_PCI_EXT_BASE	0x80000000	/* PCI external */
+ #define AR2315_PCI_EXT_SIZE	0x40000000
+ 
++/* MII registers offset inside Ethernet MMR region */
++#define AR2315_ENET0_MII_BASE	(AR2315_ENET0_BASE + 0x14)
++
+ /*
+  * Configuration registers
+  */
+--- a/arch/mips/ath25/ar5312_regs.h
++++ b/arch/mips/ath25/ar5312_regs.h
+@@ -64,6 +64,10 @@
+ #define AR5312_AR5312_REV7	0x0057		/* AR5312 WMAC (AP30-040) */
+ #define AR5312_AR2313_REV8	0x0058		/* AR2313 WMAC (AP43-030) */
+ 
++/* MII registers offset inside Ethernet MMR region */
++#define AR5312_ENET0_MII_BASE	(AR5312_ENET0_BASE + 0x14)
++#define AR5312_ENET1_MII_BASE	(AR5312_ENET1_BASE + 0x14)
++
+ /* Reset/Timer Block Address Map */
+ #define AR5312_TIMER		0x0000 /* countdown timer */
+ #define AR5312_RELOAD		0x0004 /* timer reload value */
+--- a/arch/mips/ath25/ar2315.c
++++ b/arch/mips/ath25/ar2315.c
+@@ -136,6 +136,8 @@ static void ar2315_irq_dispatch(void)
+ 
+ 	if (pending & CAUSEF_IP3)
+ 		do_IRQ(AR2315_IRQ_WLAN0);
++	else if (pending & CAUSEF_IP4)
++		do_IRQ(AR2315_IRQ_ENET0);
+ #ifdef CONFIG_PCI_AR2315
+ 	else if (pending & CAUSEF_IP5)
+ 		do_IRQ(AR2315_IRQ_LCBUS_PCI);
+@@ -169,6 +171,29 @@ void __init ar2315_arch_init_irq(void)
+ 	ar2315_misc_irq_domain = domain;
+ }
+ 
++static void ar2315_device_reset_set(u32 mask)
++{
++	u32 val;
++
++	val = ar2315_rst_reg_read(AR2315_RESET);
++	ar2315_rst_reg_write(AR2315_RESET, val | mask);
++}
++
++static void ar2315_device_reset_clear(u32 mask)
++{
++	u32 val;
++
++	val = ar2315_rst_reg_read(AR2315_RESET);
++	ar2315_rst_reg_write(AR2315_RESET, val & ~mask);
++}
++
++static struct ar231x_eth ar2315_eth_data = {
++	.reset_set = ar2315_device_reset_set,
++	.reset_clear = ar2315_device_reset_clear,
++	.reset_mac = AR2315_RESET_ENET0,
++	.reset_phy = AR2315_RESET_EPHY0,
++};
++
+ static struct resource ar2315_gpio_res[] = {
+ 	{
+ 		.name = "ar2315-gpio",
+@@ -205,6 +230,11 @@ void __init ar2315_init_devices(void)
+ 	ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
+ 	platform_device_register(&ar2315_gpio);
+ 
++	ar2315_eth_data.macaddr = ath25_board.config->enet0_mac;
++	ath25_add_ethernet(0, AR2315_ENET0_BASE, "eth0_mii",
++			   AR2315_ENET0_MII_BASE, AR2315_IRQ_ENET0,
++			   &ar2315_eth_data);
++
+ 	ath25_add_wmac(0, AR2315_WLAN0_BASE, AR2315_IRQ_WLAN0);
+ }
+ 
+--- a/arch/mips/ath25/ar5312.c
++++ b/arch/mips/ath25/ar5312.c
+@@ -132,6 +132,10 @@ static void ar5312_irq_dispatch(void)
+ 
+ 	if (pending & CAUSEF_IP2)
+ 		do_IRQ(AR5312_IRQ_WLAN0);
++	else if (pending & CAUSEF_IP3)
++		do_IRQ(AR5312_IRQ_ENET0);
++	else if (pending & CAUSEF_IP4)
++		do_IRQ(AR5312_IRQ_ENET1);
+ 	else if (pending & CAUSEF_IP5)
+ 		do_IRQ(AR5312_IRQ_WLAN1);
+ 	else if (pending & CAUSEF_IP6)
+@@ -163,6 +167,36 @@ void __init ar5312_arch_init_irq(void)
+ 	ar5312_misc_irq_domain = domain;
+ }
+ 
++static void ar5312_device_reset_set(u32 mask)
++{
++	u32 val;
++
++	val = ar5312_rst_reg_read(AR5312_RESET);
++	ar5312_rst_reg_write(AR5312_RESET, val | mask);
++}
++
++static void ar5312_device_reset_clear(u32 mask)
++{
++	u32 val;
++
++	val = ar5312_rst_reg_read(AR5312_RESET);
++	ar5312_rst_reg_write(AR5312_RESET, val & ~mask);
++}
++
++static struct ar231x_eth ar5312_eth0_data = {
++	.reset_set = ar5312_device_reset_set,
++	.reset_clear = ar5312_device_reset_clear,
++	.reset_mac = AR5312_RESET_ENET0,
++	.reset_phy = AR5312_RESET_EPHY0,
++};
++
++static struct ar231x_eth ar5312_eth1_data = {
++	.reset_set = ar5312_device_reset_set,
++	.reset_clear = ar5312_device_reset_clear,
++	.reset_mac = AR5312_RESET_ENET1,
++	.reset_phy = AR5312_RESET_EPHY1,
++};
++
+ static struct physmap_flash_data ar5312_flash_data = {
+ 	.width = 2,
+ };
+@@ -243,6 +277,7 @@ static void __init ar5312_flash_init(voi
+ void __init ar5312_init_devices(void)
+ {
+ 	struct ath25_boarddata *config;
++	u8 *c;
+ 
+ 	ar5312_flash_init();
+ 
+@@ -266,8 +301,30 @@ void __init ar5312_init_devices(void)
+ 
+ 	platform_device_register(&ar5312_gpio);
+ 
++	/* Fix up MAC addresses if necessary */
++	if (is_broadcast_ether_addr(config->enet0_mac))
++		ether_addr_copy(config->enet0_mac, config->enet1_mac);
++
++	/* If ENET0 and ENET1 have the same mac address,
++	 * increment the one from ENET1 */
++	if (ether_addr_equal(config->enet0_mac, config->enet1_mac)) {
++		c = config->enet1_mac + 5;
++		while ((c >= config->enet1_mac) && !(++(*c)))
++			c--;
++	}
++
+ 	switch (ath25_soc) {
+ 	case ATH25_SOC_AR5312:
++		ar5312_eth0_data.macaddr = config->enet0_mac;
++		ath25_add_ethernet(0, AR5312_ENET0_BASE, "eth0_mii",
++				   AR5312_ENET0_MII_BASE, AR5312_IRQ_ENET0,
++				   &ar5312_eth0_data);
++
++		ar5312_eth1_data.macaddr = config->enet1_mac;
++		ath25_add_ethernet(1, AR5312_ENET1_BASE, "eth1_mii",
++				   AR5312_ENET1_MII_BASE, AR5312_IRQ_ENET1,
++				   &ar5312_eth1_data);
++
+ 		if (!ath25_board.radio)
+ 			return;
+ 
+@@ -276,8 +333,18 @@ void __init ar5312_init_devices(void)
+ 
+ 		ath25_add_wmac(0, AR5312_WLAN0_BASE, AR5312_IRQ_WLAN0);
+ 		break;
++	/*
++	 * AR2312/3 ethernet uses the PHY of ENET0, but the MAC
++	 * of ENET1. Atheros calls it 'twisted' for a reason :)
++	 */
+ 	case ATH25_SOC_AR2312:
+ 	case ATH25_SOC_AR2313:
++		ar5312_eth1_data.reset_phy = ar5312_eth0_data.reset_phy;
++		ar5312_eth1_data.macaddr = config->enet0_mac;
++		ath25_add_ethernet(1, AR5312_ENET1_BASE, "eth0_mii",
++				   AR5312_ENET0_MII_BASE, AR5312_IRQ_ENET1,
++				   &ar5312_eth1_data);
++
+ 		if (!ath25_board.radio)
+ 			return;
+ 		break;
+--- a/arch/mips/ath25/devices.h
++++ b/arch/mips/ath25/devices.h
+@@ -32,6 +32,8 @@ extern struct ar231x_board_config ath25_
+ extern void (*ath25_irq_dispatch)(void);
+ 
+ int ath25_find_config(phys_addr_t offset, unsigned long size);
++int ath25_add_ethernet(int nr, u32 base, const char *mii_name, u32 mii_base,
++		       int irq, void *pdata);
+ void ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk);
+ int ath25_add_wmac(int nr, u32 base, int irq);
+ 
+--- a/arch/mips/ath25/devices.c
++++ b/arch/mips/ath25/devices.c
+@@ -12,6 +12,51 @@
+ struct ar231x_board_config ath25_board;
+ enum ath25_soc_type ath25_soc = ATH25_SOC_UNKNOWN;
+ 
++static struct resource ath25_eth0_res[] = {
++	{
++		.name = "eth0_membase",
++		.flags = IORESOURCE_MEM,
++	},
++	{
++		.name = "eth0_mii",
++		.flags = IORESOURCE_MEM,
++	},
++	{
++		.name = "eth0_irq",
++		.flags = IORESOURCE_IRQ,
++	}
++};
++
++static struct resource ath25_eth1_res[] = {
++	{
++		.name = "eth1_membase",
++		.flags = IORESOURCE_MEM,
++	},
++	{
++		.name = "eth1_mii",
++		.flags = IORESOURCE_MEM,
++	},
++	{
++		.name = "eth1_irq",
++		.flags = IORESOURCE_IRQ,
++	}
++};
++
++static struct platform_device ath25_eth[] = {
++	{
++		.id = 0,
++		.name = "ar231x-eth",
++		.resource = ath25_eth0_res,
++		.num_resources = ARRAY_SIZE(ath25_eth0_res)
++	},
++	{
++		.id = 1,
++		.name = "ar231x-eth",
++		.resource = ath25_eth1_res,
++		.num_resources = ARRAY_SIZE(ath25_eth1_res)
++	}
++};
++
+ static struct resource ath25_wmac0_res[] = {
+ 	{
+ 		.name = "wmac0_membase",
+@@ -70,6 +115,25 @@ const char *get_system_type(void)
+ 	return soc_type_strings[ath25_soc];
+ }
+ 
++int __init ath25_add_ethernet(int nr, u32 base, const char *mii_name,
++			      u32 mii_base, int irq, void *pdata)
++{
++	struct resource *res;
++
++	ath25_eth[nr].dev.platform_data = pdata;
++	res = &ath25_eth[nr].resource[0];
++	res->start = base;
++	res->end = base + 0x2000 - 1;
++	res++;
++	res->name = mii_name;
++	res->start = mii_base;
++	res->end = mii_base + 8 - 1;
++	res++;
++	res->start = irq;
++	res->end = irq;
++	return platform_device_register(&ath25_eth[nr]);
++}
++
+ void __init ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk)
+ {
+ 	struct uart_port s;
+--- a/arch/mips/include/asm/mach-ath25/ath25_platform.h
++++ b/arch/mips/include/asm/mach-ath25/ath25_platform.h
+@@ -70,4 +70,15 @@ struct ar231x_board_config {
+ 	const char *radio;
+ };
+ 
++/*
++ * Platform device information for the Ethernet MAC
++ */
++struct ar231x_eth {
++	void (*reset_set)(u32);
++	void (*reset_clear)(u32);
++	u32 reset_mac;
++	u32 reset_phy;
++	char *macaddr;
++};
++
+ #endif /* __ASM_MACH_ATH25_PLATFORM_H */
diff --git a/target/linux/ath25/patches-4.4/120-spiflash.patch b/target/linux/ath25/patches-4.4/120-spiflash.patch
new file mode 100644
index 0000000..7d88ee2
--- /dev/null
+++ b/target/linux/ath25/patches-4.4/120-spiflash.patch
@@ -0,0 +1,634 @@
+--- a/drivers/mtd/devices/Kconfig
++++ b/drivers/mtd/devices/Kconfig
+@@ -120,6 +120,10 @@ config MTD_BCM47XXSFLASH
+ 	  registered by bcma as platform devices. This enables driver for
+ 	  serial flash memories (only read-only mode is implemented).
+ 
++config MTD_AR2315
++	tristate "Atheros AR2315+ SPI Flash support"
++	depends on SOC_AR2315
++
+ config MTD_SLRAM
+ 	tristate "Uncached system RAM"
+ 	help
+--- a/drivers/mtd/devices/Makefile
++++ b/drivers/mtd/devices/Makefile
+@@ -14,6 +14,7 @@ obj-$(CONFIG_MTD_DATAFLASH)	+= mtd_dataf
+ obj-$(CONFIG_MTD_M25P80)	+= m25p80.o
+ obj-$(CONFIG_MTD_SPEAR_SMI)	+= spear_smi.o
+ obj-$(CONFIG_MTD_SST25L)	+= sst25l.o
++obj-$(CONFIG_MTD_AR2315)	+= ar2315.o
+ obj-$(CONFIG_MTD_BCM47XXSFLASH)	+= bcm47xxsflash.o
+ obj-$(CONFIG_MTD_ST_SPI_FSM)    += st_spi_fsm.o
+ 
+--- /dev/null
++++ b/drivers/mtd/devices/ar2315.c
+@@ -0,0 +1,459 @@
++
++/*
++ * MTD driver for the SPI Flash Memory support on Atheros AR2315
++ *
++ * Copyright (c) 2005-2006 Atheros Communications Inc.
++ * Copyright (C) 2006-2007 FON Technology, SL.
++ * Copyright (C) 2006-2007 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
++ *
++ * This code is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/types.h>
++#include <linux/errno.h>
++#include <linux/slab.h>
++#include <linux/mtd/mtd.h>
++#include <linux/mtd/partitions.h>
++#include <linux/platform_device.h>
++#include <linux/sched.h>
++#include <linux/delay.h>
++#include <linux/io.h>
++#include <linux/mutex.h>
++
++#include "ar2315_spiflash.h"
++
++#define DRIVER_NAME "ar2315-spiflash"
++
++#define busy_wait(_priv, _condition, _wait) do { \
++	while (_condition) { \
++		if (_wait > 1) \
++			msleep(_wait); \
++		else if ((_wait == 1) && need_resched()) \
++			schedule(); \
++		else \
++			udelay(1); \
++	} \
++} while (0)
++
++enum {
++	FLASH_NONE,
++	FLASH_1MB,
++	FLASH_2MB,
++	FLASH_4MB,
++	FLASH_8MB,
++	FLASH_16MB,
++};
++
++/* Flash configuration table */
++struct flashconfig {
++	u32 byte_cnt;
++	u32 sector_cnt;
++	u32 sector_size;
++};
++
++static const struct flashconfig flashconfig_tbl[] = {
++	[FLASH_NONE] = { 0, 0, 0},
++	[FLASH_1MB]  = { STM_1MB_BYTE_COUNT, STM_1MB_SECTOR_COUNT,
++			 STM_1MB_SECTOR_SIZE},
++	[FLASH_2MB]  = { STM_2MB_BYTE_COUNT, STM_2MB_SECTOR_COUNT,
++			 STM_2MB_SECTOR_SIZE},
++	[FLASH_4MB]  = { STM_4MB_BYTE_COUNT, STM_4MB_SECTOR_COUNT,
++			 STM_4MB_SECTOR_SIZE},
++	[FLASH_8MB]  = { STM_8MB_BYTE_COUNT, STM_8MB_SECTOR_COUNT,
++			 STM_8MB_SECTOR_SIZE},
++	[FLASH_16MB] = { STM_16MB_BYTE_COUNT, STM_16MB_SECTOR_COUNT,
++			 STM_16MB_SECTOR_SIZE}
++};
++
++/* Mapping of generic opcodes to STM serial flash opcodes */
++enum {
++	SPI_WRITE_ENABLE,
++	SPI_WRITE_DISABLE,
++	SPI_RD_STATUS,
++	SPI_WR_STATUS,
++	SPI_RD_DATA,
++	SPI_FAST_RD_DATA,
++	SPI_PAGE_PROGRAM,
++	SPI_SECTOR_ERASE,
++	SPI_BULK_ERASE,
++	SPI_DEEP_PWRDOWN,
++	SPI_RD_SIG,
++};
++
++struct opcodes {
++	__u16 code;
++	__s8 tx_cnt;
++	__s8 rx_cnt;
++};
++
++static const struct opcodes stm_opcodes[] = {
++	[SPI_WRITE_ENABLE] = {STM_OP_WR_ENABLE, 1, 0},
++	[SPI_WRITE_DISABLE] = {STM_OP_WR_DISABLE, 1, 0},
++	[SPI_RD_STATUS] = {STM_OP_RD_STATUS, 1, 1},
++	[SPI_WR_STATUS] = {STM_OP_WR_STATUS, 1, 0},
++	[SPI_RD_DATA] = {STM_OP_RD_DATA, 4, 4},
++	[SPI_FAST_RD_DATA] = {STM_OP_FAST_RD_DATA, 5, 0},
++	[SPI_PAGE_PROGRAM] = {STM_OP_PAGE_PGRM, 8, 0},
++	[SPI_SECTOR_ERASE] = {STM_OP_SECTOR_ERASE, 4, 0},
++	[SPI_BULK_ERASE] = {STM_OP_BULK_ERASE, 1, 0},
++	[SPI_DEEP_PWRDOWN] = {STM_OP_DEEP_PWRDOWN, 1, 0},
++	[SPI_RD_SIG] = {STM_OP_RD_SIG, 4, 1},
++};
++
++/* Driver private data structure */
++struct spiflash_priv {
++	struct mtd_info mtd;
++	void __iomem *readaddr; /* memory mapped data for read  */
++	void __iomem *mmraddr;  /* memory mapped register space */
++	struct mutex lock;	/* serialize registers access */
++};
++
++#define to_spiflash(_mtd) container_of(_mtd, struct spiflash_priv, mtd)
++
++enum {
++	FL_READY,
++	FL_READING,
++	FL_ERASING,
++	FL_WRITING
++};
++
++/*****************************************************************************/
++
++static u32
++spiflash_read_reg(struct spiflash_priv *priv, int reg)
++{
++	return ioread32(priv->mmraddr + reg);
++}
++
++static void
++spiflash_write_reg(struct spiflash_priv *priv, int reg, u32 data)
++{
++	iowrite32(data, priv->mmraddr + reg);
++}
++
++static u32
++spiflash_wait_busy(struct spiflash_priv *priv)
++{
++	u32 reg;
++
++	busy_wait(priv, (reg = spiflash_read_reg(priv, SPI_FLASH_CTL)) &
++		SPI_CTL_BUSY, 0);
++	return reg;
++}
++
++static u32
++spiflash_sendcmd(struct spiflash_priv *priv, int opcode, u32 addr)
++{
++	const struct opcodes *op;
++	u32 reg, mask;
++
++	op = &stm_opcodes[opcode];
++	reg = spiflash_wait_busy(priv);
++	spiflash_write_reg(priv, SPI_FLASH_OPCODE,
++			   ((u32)op->code) | (addr << 8));
++
++	reg &= ~SPI_CTL_TX_RX_CNT_MASK;
++	reg |= SPI_CTL_START | op->tx_cnt | (op->rx_cnt << 4);
++
++	spiflash_write_reg(priv, SPI_FLASH_CTL, reg);
++	spiflash_wait_busy(priv);
++
++	if (!op->rx_cnt)
++		return 0;
++
++	reg = spiflash_read_reg(priv, SPI_FLASH_DATA);
++
++	switch (op->rx_cnt) {
++	case 1:
++		mask = 0x000000ff;
++		break;
++	case 2:
++		mask = 0x0000ffff;
++		break;
++	case 3:
++		mask = 0x00ffffff;
++		break;
++	default:
++		mask = 0xffffffff;
++		break;
++	}
++	reg &= mask;
++
++	return reg;
++}
++
++/*
++ * Probe SPI flash device
++ * Function returns 0 for failure.
++ * and flashconfig_tbl array index for success.
++ */
++static int
++spiflash_probe_chip(struct platform_device *pdev, struct spiflash_priv *priv)
++{
++	u32 sig = spiflash_sendcmd(priv, SPI_RD_SIG, 0);
++	int flash_size;
++
++	switch (sig) {
++	case STM_8MBIT_SIGNATURE:
++		flash_size = FLASH_1MB;
++		break;
++	case STM_16MBIT_SIGNATURE:
++		flash_size = FLASH_2MB;
++		break;
++	case STM_32MBIT_SIGNATURE:
++		flash_size = FLASH_4MB;
++		break;
++	case STM_64MBIT_SIGNATURE:
++		flash_size = FLASH_8MB;
++		break;
++	case STM_128MBIT_SIGNATURE:
++		flash_size = FLASH_16MB;
++		break;
++	default:
++		dev_warn(&pdev->dev, "read of flash device signature failed!\n");
++		return 0;
++	}
++
++	return flash_size;
++}
++
++static void
++spiflash_wait_complete(struct spiflash_priv *priv, unsigned int timeout)
++{
++	busy_wait(priv, spiflash_sendcmd(priv, SPI_RD_STATUS, 0) &
++		SPI_STATUS_WIP, timeout);
++}
++
++static int
++spiflash_erase(struct mtd_info *mtd, struct erase_info *instr)
++{
++	struct spiflash_priv *priv = to_spiflash(mtd);
++	const struct opcodes *op;
++	u32 temp, reg;
++
++	if (instr->addr + instr->len > mtd->size)
++		return -EINVAL;
++
++	mutex_lock(&priv->lock);
++
++	spiflash_sendcmd(priv, SPI_WRITE_ENABLE, 0);
++	reg = spiflash_wait_busy(priv);
++
++	op = &stm_opcodes[SPI_SECTOR_ERASE];
++	temp = ((u32)instr->addr << 8) | (u32)(op->code);
++	spiflash_write_reg(priv, SPI_FLASH_OPCODE, temp);
++
++	reg &= ~SPI_CTL_TX_RX_CNT_MASK;
++	reg |= op->tx_cnt | SPI_CTL_START;
++	spiflash_write_reg(priv, SPI_FLASH_CTL, reg);
++
++	spiflash_wait_complete(priv, 20);
++
++	mutex_unlock(&priv->lock);
++
++	instr->state = MTD_ERASE_DONE;
++	mtd_erase_callback(instr);
++
++	return 0;
++}
++
++static int
++spiflash_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen,
++	      u_char *buf)
++{
++	struct spiflash_priv *priv = to_spiflash(mtd);
++
++	if (!len)
++		return 0;
++
++	if (from + len > mtd->size)
++		return -EINVAL;
++
++	*retlen = len;
++
++	mutex_lock(&priv->lock);
++
++	memcpy_fromio(buf, priv->readaddr + from, len);
++
++	mutex_unlock(&priv->lock);
++
++	return 0;
++}
++
++static int
++spiflash_write(struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen,
++	       const u8 *buf)
++{
++	struct spiflash_priv *priv = to_spiflash(mtd);
++	u32 opcode, bytes_left;
++
++	*retlen = 0;
++
++	if (!len)
++		return 0;
++
++	if (to + len > mtd->size)
++		return -EINVAL;
++
++	bytes_left = len;
++
++	do {
++		u32 read_len, reg, page_offset, spi_data = 0;
++
++		read_len = min(bytes_left, sizeof(u32));
++
++		/* 32-bit writes cannot span across a page boundary
++		 * (256 bytes). This types of writes require two page
++		 * program operations to handle it correctly. The STM part
++		 * will write the overflow data to the beginning of the
++		 * current page as opposed to the subsequent page.
++		 */
++		page_offset = (to & (STM_PAGE_SIZE - 1)) + read_len;
++
++		if (page_offset > STM_PAGE_SIZE)
++			read_len -= (page_offset - STM_PAGE_SIZE);
++
++		mutex_lock(&priv->lock);
++
++		spiflash_sendcmd(priv, SPI_WRITE_ENABLE, 0);
++		spi_data = 0;
++		switch (read_len) {
++		case 4:
++			spi_data |= buf[3] << 24;
++			/* fall through */
++		case 3:
++			spi_data |= buf[2] << 16;
++			/* fall through */
++		case 2:
++			spi_data |= buf[1] << 8;
++			/* fall through */
++		case 1:
++			spi_data |= buf[0] & 0xff;
++			break;
++		default:
++			break;
++		}
++
++		spiflash_write_reg(priv, SPI_FLASH_DATA, spi_data);
++		opcode = stm_opcodes[SPI_PAGE_PROGRAM].code |
++			(to & 0x00ffffff) << 8;
++		spiflash_write_reg(priv, SPI_FLASH_OPCODE, opcode);
++
++		reg = spiflash_read_reg(priv, SPI_FLASH_CTL);
++		reg &= ~SPI_CTL_TX_RX_CNT_MASK;
++		reg |= (read_len + 4) | SPI_CTL_START;
++		spiflash_write_reg(priv, SPI_FLASH_CTL, reg);
++
++		spiflash_wait_complete(priv, 1);
++
++		mutex_unlock(&priv->lock);
++
++		bytes_left -= read_len;
++		to += read_len;
++		buf += read_len;
++
++		*retlen += read_len;
++	} while (bytes_left != 0);
++
++	return 0;
++}
++
++#if defined CONFIG_MTD_REDBOOT_PARTS || CONFIG_MTD_MYLOADER_PARTS
++static const char * const part_probe_types[] = {
++	"cmdlinepart", "RedBoot", "MyLoader", NULL
++};
++#endif
++
++static int
++spiflash_probe(struct platform_device *pdev)
++{
++	struct spiflash_priv *priv;
++	struct mtd_info *mtd;
++	struct resource *res;
++	int index;
++	int result = 0;
++
++	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
++	if (!priv)
++		return -ENOMEM;
++
++	mutex_init(&priv->lock);
++	mtd = &priv->mtd;
++
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
++	priv->mmraddr = devm_ioremap_resource(&pdev->dev, res);
++	if (IS_ERR(priv->mmraddr)) {
++		dev_warn(&pdev->dev, "failed to map flash MMR\n");
++		return PTR_ERR(priv->mmraddr);
++	}
++
++	index = spiflash_probe_chip(pdev, priv);
++	if (!index) {
++		dev_warn(&pdev->dev, "found no flash device\n");
++		return -ENODEV;
++	}
++
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	priv->readaddr = devm_ioremap_resource(&pdev->dev, res);
++	if (IS_ERR(priv->readaddr)) {
++		dev_warn(&pdev->dev, "failed to map flash read mem\n");
++		return PTR_ERR(priv->readaddr);
++	}
++
++	platform_set_drvdata(pdev, priv);
++	mtd->name = "spiflash";
++	mtd->type = MTD_NORFLASH;
++	mtd->flags = (MTD_CAP_NORFLASH|MTD_WRITEABLE);
++	mtd->size = flashconfig_tbl[index].byte_cnt;
++	mtd->erasesize = flashconfig_tbl[index].sector_size;
++	mtd->writesize = 1;
++	mtd->numeraseregions = 0;
++	mtd->eraseregions = NULL;
++	mtd->_erase = spiflash_erase;
++	mtd->_read = spiflash_read;
++	mtd->_write = spiflash_write;
++	mtd->owner = THIS_MODULE;
++
++	dev_info(&pdev->dev, "%lld Kbytes flash detected\n", mtd->size >> 10);
++
++#if defined CONFIG_MTD_REDBOOT_PARTS || CONFIG_MTD_MYLOADER_PARTS
++	/* parse redboot partitions */
++
++	result = mtd_device_parse_register(mtd, part_probe_types,
++					   NULL, NULL, 0);
++#endif
++
++	return result;
++}
++
++static int
++spiflash_remove(struct platform_device *pdev)
++{
++	struct spiflash_priv *priv = platform_get_drvdata(pdev);
++
++	mtd_device_unregister(&priv->mtd);
++
++	return 0;
++}
++
++static struct platform_driver spiflash_driver = {
++	.driver.name = DRIVER_NAME,
++	.probe = spiflash_probe,
++	.remove = spiflash_remove,
++};
++
++module_platform_driver(spiflash_driver);
++
++MODULE_LICENSE("GPL");
++MODULE_AUTHOR("OpenWrt.org");
++MODULE_AUTHOR("Atheros Communications Inc");
++MODULE_DESCRIPTION("MTD driver for SPI Flash on Atheros AR2315+ SOC");
++MODULE_ALIAS("platform:" DRIVER_NAME);
++
+--- /dev/null
++++ b/drivers/mtd/devices/ar2315_spiflash.h
+@@ -0,0 +1,106 @@
++/*
++ * Atheros AR2315 SPI Flash Memory support header file.
++ *
++ * Copyright (c) 2005, Atheros Communications Inc.
++ * Copyright (C) 2006 FON Technology, SL.
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++ *
++ * This code is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++#ifndef __AR2315_SPIFLASH_H
++#define __AR2315_SPIFLASH_H
++
++#define STM_PAGE_SIZE           256
++
++#define SFI_WRITE_BUFFER_SIZE   4
++#define SFI_FLASH_ADDR_MASK     0x00ffffff
++
++#define STM_8MBIT_SIGNATURE     0x13
++#define STM_M25P80_BYTE_COUNT   1048576
++#define STM_M25P80_SECTOR_COUNT 16
++#define STM_M25P80_SECTOR_SIZE  0x10000
++
++#define STM_16MBIT_SIGNATURE    0x14
++#define STM_M25P16_BYTE_COUNT   2097152
++#define STM_M25P16_SECTOR_COUNT 32
++#define STM_M25P16_SECTOR_SIZE  0x10000
++
++#define STM_32MBIT_SIGNATURE    0x15
++#define STM_M25P32_BYTE_COUNT   4194304
++#define STM_M25P32_SECTOR_COUNT 64
++#define STM_M25P32_SECTOR_SIZE  0x10000
++
++#define STM_64MBIT_SIGNATURE    0x16
++#define STM_M25P64_BYTE_COUNT   8388608
++#define STM_M25P64_SECTOR_COUNT 128
++#define STM_M25P64_SECTOR_SIZE  0x10000
++
++#define STM_128MBIT_SIGNATURE   0x17
++#define STM_M25P128_BYTE_COUNT   16777216
++#define STM_M25P128_SECTOR_COUNT 256
++#define STM_M25P128_SECTOR_SIZE  0x10000
++
++#define STM_1MB_BYTE_COUNT   STM_M25P80_BYTE_COUNT
++#define STM_1MB_SECTOR_COUNT STM_M25P80_SECTOR_COUNT
++#define STM_1MB_SECTOR_SIZE  STM_M25P80_SECTOR_SIZE
++#define STM_2MB_BYTE_COUNT   STM_M25P16_BYTE_COUNT
++#define STM_2MB_SECTOR_COUNT STM_M25P16_SECTOR_COUNT
++#define STM_2MB_SECTOR_SIZE  STM_M25P16_SECTOR_SIZE
++#define STM_4MB_BYTE_COUNT   STM_M25P32_BYTE_COUNT
++#define STM_4MB_SECTOR_COUNT STM_M25P32_SECTOR_COUNT
++#define STM_4MB_SECTOR_SIZE  STM_M25P32_SECTOR_SIZE
++#define STM_8MB_BYTE_COUNT   STM_M25P64_BYTE_COUNT
++#define STM_8MB_SECTOR_COUNT STM_M25P64_SECTOR_COUNT
++#define STM_8MB_SECTOR_SIZE  STM_M25P64_SECTOR_SIZE
++#define STM_16MB_BYTE_COUNT   STM_M25P128_BYTE_COUNT
++#define STM_16MB_SECTOR_COUNT STM_M25P128_SECTOR_COUNT
++#define STM_16MB_SECTOR_SIZE  STM_M25P128_SECTOR_SIZE
++
++/*
++ * ST Microelectronics Opcodes for Serial Flash
++ */
++
++#define STM_OP_WR_ENABLE       0x06     /* Write Enable */
++#define STM_OP_WR_DISABLE      0x04     /* Write Disable */
++#define STM_OP_RD_STATUS       0x05     /* Read Status */
++#define STM_OP_WR_STATUS       0x01     /* Write Status */
++#define STM_OP_RD_DATA         0x03     /* Read Data */
++#define STM_OP_FAST_RD_DATA    0x0b     /* Fast Read Data */
++#define STM_OP_PAGE_PGRM       0x02     /* Page Program */
++#define STM_OP_SECTOR_ERASE    0xd8     /* Sector Erase */
++#define STM_OP_BULK_ERASE      0xc7     /* Bulk Erase */
++#define STM_OP_DEEP_PWRDOWN    0xb9     /* Deep Power-Down Mode */
++#define STM_OP_RD_SIG          0xab     /* Read Electronic Signature */
++
++#define STM_STATUS_WIP       0x01       /* Write-In-Progress */
++#define STM_STATUS_WEL       0x02       /* Write Enable Latch */
++#define STM_STATUS_BP0       0x04       /* Block Protect 0 */
++#define STM_STATUS_BP1       0x08       /* Block Protect 1 */
++#define STM_STATUS_BP2       0x10       /* Block Protect 2 */
++#define STM_STATUS_SRWD      0x80       /* Status Register Write Disable */
++
++/*
++ * SPI Flash Interface Registers
++ */
++
++#define SPI_FLASH_CTL           0x00
++#define SPI_FLASH_OPCODE        0x04
++#define SPI_FLASH_DATA          0x08
++
++#define SPI_CTL_START           0x00000100
++#define SPI_CTL_BUSY            0x00010000
++#define SPI_CTL_TXCNT_MASK      0x0000000f
++#define SPI_CTL_RXCNT_MASK      0x000000f0
++#define SPI_CTL_TX_RX_CNT_MASK  0x000000ff
++#define SPI_CTL_SIZE_MASK       0x00060000
++
++#define SPI_CTL_CLK_SEL_MASK    0x03000000
++#define SPI_OPCODE_MASK         0x000000ff
++
++#define SPI_STATUS_WIP		STM_STATUS_WIP
++
++#endif
+--- a/arch/mips/ath25/ar2315.c
++++ b/arch/mips/ath25/ar2315.c
+@@ -220,6 +220,28 @@ static struct platform_device ar2315_gpi
+ 	.num_resources = ARRAY_SIZE(ar2315_gpio_res)
+ };
+ 
++static struct resource ar2315_spiflash_res[] = {
++	{
++		.name = "spiflash_read",
++		.flags = IORESOURCE_MEM,
++		.start = AR2315_SPI_READ_BASE,
++		.end = AR2315_SPI_READ_BASE + AR2315_SPI_READ_SIZE - 1,
++	},
++	{
++		.name = "spiflash_mmr",
++		.flags = IORESOURCE_MEM,
++		.start = AR2315_SPI_MMR_BASE,
++		.end = AR2315_SPI_MMR_BASE + AR2315_SPI_MMR_SIZE - 1,
++	},
++};
++
++static struct platform_device ar2315_spiflash = {
++	.id = 0,
++	.name = "ar2315-spiflash",
++	.resource = ar2315_spiflash_res,
++	.num_resources = ARRAY_SIZE(ar2315_spiflash_res)
++};
++
+ void __init ar2315_init_devices(void)
+ {
+ 	/* Find board configuration */
+@@ -230,6 +252,8 @@ void __init ar2315_init_devices(void)
+ 	ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
+ 	platform_device_register(&ar2315_gpio);
+ 
++	platform_device_register(&ar2315_spiflash);
++
+ 	ar2315_eth_data.macaddr = ath25_board.config->enet0_mac;
+ 	ath25_add_ethernet(0, AR2315_ENET0_BASE, "eth0_mii",
+ 			   AR2315_ENET0_MII_BASE, AR2315_IRQ_ENET0,
diff --git a/target/linux/ath25/patches-4.4/130-watchdog.patch b/target/linux/ath25/patches-4.4/130-watchdog.patch
new file mode 100644
index 0000000..251768f
--- /dev/null
+++ b/target/linux/ath25/patches-4.4/130-watchdog.patch
@@ -0,0 +1,277 @@
+--- /dev/null
++++ b/drivers/watchdog/ar2315-wtd.c
+@@ -0,0 +1,209 @@
++/*
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, see <http://www.gnu.org/licenses/>.
++ *
++ * Copyright (C) 2008 John Crispin <blogic@openwrt.org>
++ * Based on EP93xx and ifxmips wdt driver
++ */
++
++#include <linux/interrupt.h>
++#include <linux/module.h>
++#include <linux/moduleparam.h>
++#include <linux/types.h>
++#include <linux/miscdevice.h>
++#include <linux/watchdog.h>
++#include <linux/fs.h>
++#include <linux/ioport.h>
++#include <linux/notifier.h>
++#include <linux/reboot.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/io.h>
++#include <linux/uaccess.h>
++
++#define DRIVER_NAME	"ar2315-wdt"
++
++#define CLOCK_RATE 40000000
++#define HEARTBEAT(x) (x < 1 || x > 90 ? 20 : x)
++
++#define WDT_REG_TIMER		0x00
++#define WDT_REG_CTRL		0x04
++
++#define WDT_CTRL_ACT_NONE	0x00000000	/* No action */
++#define WDT_CTRL_ACT_NMI	0x00000001	/* NMI on watchdog */
++#define WDT_CTRL_ACT_RESET	0x00000002	/* reset on watchdog */
++
++static int wdt_timeout = 20;
++static int started;
++static int in_use;
++static void __iomem *wdt_base;
++
++static inline void ar2315_wdt_wr(unsigned reg, u32 val)
++{
++	iowrite32(val, wdt_base + reg);
++}
++
++static void
++ar2315_wdt_enable(void)
++{
++	ar2315_wdt_wr(WDT_REG_TIMER, wdt_timeout * CLOCK_RATE);
++}
++
++static ssize_t
++ar2315_wdt_write(struct file *file, const char __user *data, size_t len,
++		 loff_t *ppos)
++{
++	if (len)
++		ar2315_wdt_enable();
++	return len;
++}
++
++static int
++ar2315_wdt_open(struct inode *inode, struct file *file)
++{
++	if (in_use)
++		return -EBUSY;
++	ar2315_wdt_enable();
++	in_use = 1;
++	started = 1;
++	return nonseekable_open(inode, file);
++}
++
++static int
++ar2315_wdt_release(struct inode *inode, struct file *file)
++{
++	in_use = 0;
++	return 0;
++}
++
++static irqreturn_t
++ar2315_wdt_interrupt(int irq, void *dev)
++{
++	struct platform_device *pdev = (struct platform_device *)dev;
++
++	if (started) {
++		dev_crit(&pdev->dev, "watchdog expired, rebooting system\n");
++		emergency_restart();
++	} else {
++		ar2315_wdt_wr(WDT_REG_CTRL, 0);
++		ar2315_wdt_wr(WDT_REG_TIMER, 0);
++	}
++	return IRQ_HANDLED;
++}
++
++static struct watchdog_info ident = {
++	.options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
++	.identity = "ar2315 Watchdog",
++};
++
++static long
++ar2315_wdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
++{
++	int new_wdt_timeout;
++	int ret = -ENOIOCTLCMD;
++
++	switch (cmd) {
++	case WDIOC_GETSUPPORT:
++		ret = copy_to_user((void __user *)arg, &ident, sizeof(ident)) ?
++		      -EFAULT : 0;
++		break;
++	case WDIOC_KEEPALIVE:
++		ar2315_wdt_enable();
++		ret = 0;
++		break;
++	case WDIOC_SETTIMEOUT:
++		ret = get_user(new_wdt_timeout, (int __user *)arg);
++		if (ret)
++			break;
++		wdt_timeout = HEARTBEAT(new_wdt_timeout);
++		ar2315_wdt_enable();
++		break;
++	case WDIOC_GETTIMEOUT:
++		ret = put_user(wdt_timeout, (int __user *)arg);
++		break;
++	}
++	return ret;
++}
++
++static const struct file_operations ar2315_wdt_fops = {
++	.owner		= THIS_MODULE,
++	.llseek		= no_llseek,
++	.write		= ar2315_wdt_write,
++	.unlocked_ioctl	= ar2315_wdt_ioctl,
++	.open		= ar2315_wdt_open,
++	.release	= ar2315_wdt_release,
++};
++
++static struct miscdevice ar2315_wdt_miscdev = {
++	.minor	= WATCHDOG_MINOR,
++	.name	= "watchdog",
++	.fops	= &ar2315_wdt_fops,
++};
++
++static int
++ar2315_wdt_probe(struct platform_device *dev)
++{
++	struct resource *mem_res, *irq_res;
++	int ret = 0;
++
++	if (wdt_base)
++		return -EBUSY;
++
++	irq_res = platform_get_resource(dev, IORESOURCE_IRQ, 0);
++	if (!irq_res) {
++		dev_err(&dev->dev, "no IRQ resource\n");
++		return -ENOENT;
++	}
++
++	mem_res = platform_get_resource(dev, IORESOURCE_MEM, 0);
++	wdt_base = devm_ioremap_resource(&dev->dev, mem_res);
++	if (IS_ERR(wdt_base))
++		return PTR_ERR(wdt_base);
++
++	ret = devm_request_irq(&dev->dev, irq_res->start, ar2315_wdt_interrupt,
++			       0, DRIVER_NAME, dev);
++	if (ret) {
++		dev_err(&dev->dev, "failed to register inetrrupt\n");
++		goto out;
++	}
++
++	ret = misc_register(&ar2315_wdt_miscdev);
++	if (ret)
++		dev_err(&dev->dev, "failed to register miscdev\n");
++
++out:
++	return ret;
++}
++
++static int
++ar2315_wdt_remove(struct platform_device *dev)
++{
++	misc_deregister(&ar2315_wdt_miscdev);
++	return 0;
++}
++
++static struct platform_driver ar2315_wdt_driver = {
++	.probe = ar2315_wdt_probe,
++	.remove = ar2315_wdt_remove,
++	.driver = {
++		.name = DRIVER_NAME,
++		.owner = THIS_MODULE,
++	},
++};
++
++module_platform_driver(ar2315_wdt_driver);
++
++MODULE_DESCRIPTION("Atheros AR2315 hardware watchdog driver");
++MODULE_AUTHOR("John Crispin <blogic@openwrt.org>");
++MODULE_LICENSE("GPL");
++MODULE_ALIAS("platform:" DRIVER_NAME);
+--- a/drivers/watchdog/Kconfig
++++ b/drivers/watchdog/Kconfig
+@@ -1345,6 +1345,13 @@ config RALINK_WDT
+ 	help
+ 	  Hardware driver for the Ralink SoC Watchdog Timer.
+ 
++config AR2315_WDT
++	tristate "Atheros AR2315+ WiSoCs Watchdog Timer"
++	depends on ATH25
++	help
++	  Hardware driver for the built-in watchdog timer on the Atheros
++	  AR2315/AR2316 WiSoCs.
++
+ # PARISC Architecture
+ 
+ # POWERPC Architecture
+--- a/drivers/watchdog/Makefile
++++ b/drivers/watchdog/Makefile
+@@ -143,6 +143,7 @@ obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o
+ obj-$(CONFIG_PNX833X_WDT) += pnx833x_wdt.o
+ obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o
+ obj-$(CONFIG_AR7_WDT) += ar7_wdt.o
++obj-$(CONFIG_AR2315_WDT) += ar2315-wtd.o
+ obj-$(CONFIG_TXX9_WDT) += txx9wdt.o
+ obj-$(CONFIG_OCTEON_WDT) += octeon-wdt.o
+ octeon-wdt-y := octeon-wdt-main.o octeon-wdt-nmi.o
+--- a/arch/mips/ath25/ar2315.c
++++ b/arch/mips/ath25/ar2315.c
+@@ -220,6 +220,24 @@ static struct platform_device ar2315_gpi
+ 	.num_resources = ARRAY_SIZE(ar2315_gpio_res)
+ };
+ 
++static struct resource ar2315_wdt_res[] = {
++	{
++		.flags = IORESOURCE_MEM,
++		.start = AR2315_RST_BASE + AR2315_WDT_TIMER,
++		.end = AR2315_RST_BASE + AR2315_WDT_TIMER + 8 - 1,
++	},
++	{
++		.flags = IORESOURCE_IRQ,
++	}
++};
++
++static struct platform_device ar2315_wdt = {
++	.id = 0,
++	.name = "ar2315-wdt",
++	.resource = ar2315_wdt_res,
++	.num_resources = ARRAY_SIZE(ar2315_wdt_res)
++};
++
+ static struct resource ar2315_spiflash_res[] = {
+ 	{
+ 		.name = "spiflash_read",
+@@ -252,6 +270,11 @@ void __init ar2315_init_devices(void)
+ 	ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
+ 	platform_device_register(&ar2315_gpio);
+ 
++	ar2315_wdt_res[1].start = irq_create_mapping(ar2315_misc_irq_domain,
++						     AR2315_MISC_IRQ_WATCHDOG);
++	ar2315_wdt_res[1].end = ar2315_wdt_res[1].start;
++	platform_device_register(&ar2315_wdt);
++
+ 	platform_device_register(&ar2315_spiflash);
+ 
+ 	ar2315_eth_data.macaddr = ath25_board.config->enet0_mac;
diff --git a/target/linux/ath25/patches-4.4/140-redboot_boardconfig.patch b/target/linux/ath25/patches-4.4/140-redboot_boardconfig.patch
new file mode 100644
index 0000000..98dbf52
--- /dev/null
+++ b/target/linux/ath25/patches-4.4/140-redboot_boardconfig.patch
@@ -0,0 +1,60 @@
+--- a/drivers/mtd/redboot.c
++++ b/drivers/mtd/redboot.c
+@@ -30,6 +30,8 @@
+ #include <linux/mtd/partitions.h>
+ #include <linux/module.h>
+ 
++#define BOARD_CONFIG_PART		"boardconfig"
++
+ struct fis_image_desc {
+     unsigned char name[16];      // Null terminated name
+     uint32_t	  flash_base;    // Address within FLASH of image
+@@ -60,6 +62,7 @@ static int parse_redboot_partitions(stru
+ 				    struct mtd_partition **pparts,
+ 				    struct mtd_part_parser_data *data)
+ {
++	unsigned long max_offset = 0;
+ 	int nrparts = 0;
+ 	struct fis_image_desc *buf;
+ 	struct mtd_partition *parts;
+@@ -225,14 +228,15 @@ static int parse_redboot_partitions(stru
+ 		}
+ 	}
+ #endif
+-	parts = kzalloc(sizeof(*parts)*nrparts + nulllen + namelen, GFP_KERNEL);
++	parts = kzalloc(sizeof(*parts) * (nrparts + 1) + nulllen + namelen +
++			sizeof(BOARD_CONFIG_PART), GFP_KERNEL);
+ 
+ 	if (!parts) {
+ 		ret = -ENOMEM;
+ 		goto out;
+ 	}
+ 
+-	nullname = (char *)&parts[nrparts];
++	nullname = (char *)&parts[nrparts + 1];
+ #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED
+ 	if (nulllen > 0) {
+ 		strcpy(nullname, nullstring);
+@@ -251,6 +255,8 @@ static int parse_redboot_partitions(stru
+ 	}
+ #endif
+ 	for ( ; i<nrparts; i++) {
++		if (max_offset < buf[i].flash_base + buf[i].size)
++			max_offset = buf[i].flash_base + buf[i].size;
+ 		parts[i].size = fl->img->size;
+ 		parts[i].offset = fl->img->flash_base;
+ 		parts[i].name = names;
+@@ -284,6 +290,13 @@ static int parse_redboot_partitions(stru
+ 		fl = fl->next;
+ 		kfree(tmp_fl);
+ 	}
++	if (master->size - max_offset >= master->erasesize) {
++		parts[nrparts].size = master->size - max_offset;
++		parts[nrparts].offset = max_offset;
++		parts[nrparts].name = names;
++		strcpy(names, BOARD_CONFIG_PART);
++		nrparts++;
++	}
+ 	ret = nrparts;
+ 	*pparts = parts;
+  out:
diff --git a/target/linux/ath25/patches-4.4/141-redboot_partition_scan.patch b/target/linux/ath25/patches-4.4/141-redboot_partition_scan.patch
new file mode 100644
index 0000000..d1d281e
--- /dev/null
+++ b/target/linux/ath25/patches-4.4/141-redboot_partition_scan.patch
@@ -0,0 +1,44 @@
+--- a/drivers/mtd/redboot.c
++++ b/drivers/mtd/redboot.c
+@@ -79,12 +79,18 @@ static int parse_redboot_partitions(stru
+ 	static char nullstring[] = "unallocated";
+ #endif
+ 
++	buf = vmalloc(master->erasesize);
++	if (!buf)
++		return -ENOMEM;
++
++ restart:
+ 	if ( directory < 0 ) {
+ 		offset = master->size + directory * master->erasesize;
+ 		while (mtd_block_isbad(master, offset)) {
+ 			if (!offset) {
+ 			nogood:
+ 				printk(KERN_NOTICE "Failed to find a non-bad block to check for RedBoot partition table\n");
++				vfree(buf);
+ 				return -EIO;
+ 			}
+ 			offset -= master->erasesize;
+@@ -97,10 +103,6 @@ static int parse_redboot_partitions(stru
+ 				goto nogood;
+ 		}
+ 	}
+-	buf = vmalloc(master->erasesize);
+-
+-	if (!buf)
+-		return -ENOMEM;
+ 
+ 	printk(KERN_NOTICE "Searching for RedBoot partition table in %s at offset 0x%lx\n",
+ 	       master->name, offset);
+@@ -173,6 +175,11 @@ static int parse_redboot_partitions(stru
+ 	}
+ 	if (i == numslots) {
+ 		/* Didn't find it */
++		if (offset + master->erasesize < master->size) {
++			/* not at the end of the flash yet, maybe next block */
++			directory++;
++			goto restart;
++		}
+ 		printk(KERN_NOTICE "No RedBoot partition table detected in %s\n",
+ 		       master->name);
+ 		ret = 0;
diff --git a/target/linux/ath25/patches-4.4/142-redboot_various_erase_size_fix.patch b/target/linux/ath25/patches-4.4/142-redboot_various_erase_size_fix.patch
new file mode 100644
index 0000000..e1b0a89
--- /dev/null
+++ b/target/linux/ath25/patches-4.4/142-redboot_various_erase_size_fix.patch
@@ -0,0 +1,72 @@
+--- a/drivers/mtd/redboot.c
++++ b/drivers/mtd/redboot.c
+@@ -58,6 +58,22 @@ static inline int redboot_checksum(struc
+ 	return 1;
+ }
+ 
++static uint32_t mtd_get_offset_erasesize(struct mtd_info *mtd, uint64_t offset)
++{
++	struct mtd_erase_region_info *regions = mtd->eraseregions;
++	int i;
++
++	for (i = 0; i < mtd->numeraseregions; i++) {
++		if (regions[i].offset +
++		    regions[i].numblocks * regions[i].erasesize <= offset)
++			continue;
++
++		return regions[i].erasesize;
++	}
++
++	return mtd->erasesize;
++}
++
+ static int parse_redboot_partitions(struct mtd_info *master,
+ 				    struct mtd_partition **pparts,
+ 				    struct mtd_part_parser_data *data)
+@@ -74,6 +90,7 @@ static int parse_redboot_partitions(stru
+ 	int namelen = 0;
+ 	int nulllen = 0;
+ 	int numslots;
++	int first_slot;
+ 	unsigned long offset;
+ #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED
+ 	static char nullstring[] = "unallocated";
+@@ -186,7 +203,10 @@ static int parse_redboot_partitions(stru
+ 		goto out;
+ 	}
+ 
+-	for (i = 0; i < numslots; i++) {
++	first_slot = (buf[i].flash_base & (master->erasesize - 1)) /
++		     sizeof(struct fis_image_desc);
++
++	for (i = first_slot; i < first_slot + numslots; i++) {
+ 		struct fis_list *new_fl, **prev;
+ 
+ 		if (buf[i].name[0] == 0xff) {
+@@ -262,12 +282,13 @@ static int parse_redboot_partitions(stru
+ 	}
+ #endif
+ 	for ( ; i<nrparts; i++) {
+-		if (max_offset < buf[i].flash_base + buf[i].size)
+-			max_offset = buf[i].flash_base + buf[i].size;
+ 		parts[i].size = fl->img->size;
+ 		parts[i].offset = fl->img->flash_base;
+ 		parts[i].name = names;
+ 
++		if (max_offset < parts[i].offset + parts[i].size)
++			max_offset = parts[i].offset + parts[i].size;
++
+ 		strcpy(names, fl->img->name);
+ #ifdef CONFIG_MTD_REDBOOT_PARTS_READONLY
+ 		if (!memcmp(names, "RedBoot", 8) ||
+@@ -297,7 +318,9 @@ static int parse_redboot_partitions(stru
+ 		fl = fl->next;
+ 		kfree(tmp_fl);
+ 	}
+-	if (master->size - max_offset >= master->erasesize) {
++
++	if (master->size - max_offset >=
++	    mtd_get_offset_erasesize(master, max_offset)) {
+ 		parts[nrparts].size = master->size - max_offset;
+ 		parts[nrparts].offset = max_offset;
+ 		parts[nrparts].name = names;
diff --git a/target/linux/ath25/patches-4.4/210-reset_button.patch b/target/linux/ath25/patches-4.4/210-reset_button.patch
new file mode 100644
index 0000000..34ef46b
--- /dev/null
+++ b/target/linux/ath25/patches-4.4/210-reset_button.patch
@@ -0,0 +1,71 @@
+--- a/arch/mips/ath25/Makefile
++++ b/arch/mips/ath25/Makefile
+@@ -8,7 +8,7 @@
+ # Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
+ #
+ 
+-obj-y += board.o prom.o devices.o
++obj-y += board.o prom.o devices.o reset.o
+ 
+ obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
+ 
+--- /dev/null
++++ b/arch/mips/ath25/reset.c
+@@ -0,0 +1,57 @@
++#include <linux/init.h>
++#include <linux/slab.h>
++#include <linux/platform_device.h>
++#include <linux/gpio_keys.h>
++#include <linux/input.h>
++#include <ath25_platform.h>
++#include "devices.h"
++
++static int __init
++ar231x_init_reset(void)
++{
++	struct platform_device *pdev;
++	struct gpio_keys_platform_data pdata;
++	struct gpio_keys_button *p;
++	int err;
++
++	if (ath25_board.config->reset_config_gpio == 0xffff)
++		return -ENODEV;
++
++	p = kzalloc(sizeof(*p), GFP_KERNEL);
++	if (!p)
++		goto err;
++
++	p->desc = "reset";
++	p->type = EV_KEY;
++	p->code = KEY_RESTART;
++	p->debounce_interval = 60;
++	p->gpio = ath25_board.config->reset_config_gpio;
++
++	memset(&pdata, 0, sizeof(pdata));
++	pdata.poll_interval = 20;
++	pdata.buttons = p;
++	pdata.nbuttons = 1;
++
++	pdev = platform_device_alloc("gpio-keys-polled", 0);
++	if (!pdev)
++		goto err_free;
++
++	err = platform_device_add_data(pdev, &pdata, sizeof(pdata));
++	if (err)
++		goto err_put_pdev;
++
++	err = platform_device_add(pdev);
++	if (err)
++		goto err_put_pdev;
++
++	return 0;
++
++err_put_pdev:
++	platform_device_put(pdev);
++err_free:
++	kfree(p);
++err:
++	return -ENOMEM;
++}
++
++module_init(ar231x_init_reset);
diff --git a/target/linux/ath25/patches-4.4/220-enet_micrel_workaround.patch b/target/linux/ath25/patches-4.4/220-enet_micrel_workaround.patch
new file mode 100644
index 0000000..398495a
--- /dev/null
+++ b/target/linux/ath25/patches-4.4/220-enet_micrel_workaround.patch
@@ -0,0 +1,91 @@
+--- a/drivers/net/ethernet/atheros/ar231x/ar231x.c
++++ b/drivers/net/ethernet/atheros/ar231x/ar231x.c
+@@ -135,6 +135,7 @@ static int ar231x_mdiobus_write(struct m
+ static int ar231x_mdiobus_reset(struct mii_bus *bus);
+ static int ar231x_mdiobus_probe(struct net_device *dev);
+ static void ar231x_adjust_link(struct net_device *dev);
++static bool no_phy;
+ 
+ #ifndef ERR
+ #define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args)
+@@ -167,6 +168,32 @@ static const struct net_device_ops ar231
+ #endif
+ };
+ 
++static int get_phy_id(struct mii_bus *bus, int addr, u32 *phy_id)
++{
++	int phy_reg;
++
++	/**
++	 * Grab the bits from PHYIR1, and put them
++	 * in the upper half.
++	 */
++	phy_reg = mdiobus_read(bus, addr, MII_PHYSID1);
++
++	if (phy_reg < 0)
++		return -EIO;
++
++	*phy_id = (phy_reg & 0xffff) << 16;
++
++	/* Grab the bits from PHYIR2, and put them in the lower half */
++	phy_reg = mdiobus_read(bus, addr, MII_PHYSID2);
++
++	if (phy_reg < 0)
++		return -EIO;
++
++	*phy_id |= (phy_reg & 0xffff);
++
++	return 0;
++}
++
+ static int ar231x_probe(struct platform_device *pdev)
+ {
+ 	struct net_device *dev;
+@@ -273,6 +300,24 @@ static int ar231x_probe(struct platform_
+ 
+ 	mdiobus_register(sp->mii_bus);
+ 
++	/**
++	 * Workaround for Micrel switch, which is only available on
++	 * one PHY and cannot be configured through MDIO.
++	 */
++	if (!no_phy) {
++		u32 phy_id = 0;
++
++		get_phy_id(sp->mii_bus, 1, &phy_id);
++		if (phy_id == 0x00221450)
++			no_phy = true;
++	}
++	if (no_phy) {
++		sp->link = 1;
++		netif_carrier_on(dev);
++		return 0;
++	}
++	no_phy = true;
++
+ 	if (ar231x_mdiobus_probe(dev) != 0) {
+ 		printk(KERN_ERR "%s: mdiobus_probe failed\n", dev->name);
+ 		rx_tasklet_cleanup(dev);
+@@ -329,8 +374,10 @@ static int ar231x_remove(struct platform
+ 	rx_tasklet_cleanup(dev);
+ 	ar231x_init_cleanup(dev);
+ 	unregister_netdev(dev);
+-	mdiobus_unregister(sp->mii_bus);
+-	mdiobus_free(sp->mii_bus);
++	if (sp->mii_bus) {
++		mdiobus_unregister(sp->mii_bus);
++		mdiobus_free(sp->mii_bus);
++	}
+ 	kfree(dev);
+ 	return 0;
+ }
+@@ -1079,6 +1126,9 @@ static int ar231x_ioctl(struct net_devic
+ {
+ 	struct ar231x_private *sp = netdev_priv(dev);
+ 
++	if (!sp->phy_dev)
++		return -ENODEV;
++
+ 	switch (cmd) {
+ 	case SIOCGMIIPHY:
+ 	case SIOCGMIIREG:
diff --git a/target/linux/ath25/patches-4.4/330-board_leds.patch b/target/linux/ath25/patches-4.4/330-board_leds.patch
new file mode 100644
index 0000000..e357fc6
--- /dev/null
+++ b/target/linux/ath25/patches-4.4/330-board_leds.patch
@@ -0,0 +1,116 @@
+--- a/arch/mips/ath25/ar2315.c
++++ b/arch/mips/ath25/ar2315.c
+@@ -23,6 +23,7 @@
+ #include <linux/reboot.h>
+ #include <linux/delay.h>
+ #include <linux/gpio.h>
++#include <linux/leds.h>
+ #include <asm/bootinfo.h>
+ #include <asm/reboot.h>
+ #include <asm/time.h>
+@@ -260,6 +261,50 @@ static struct platform_device ar2315_spi
+ 	.num_resources = ARRAY_SIZE(ar2315_spiflash_res)
+ };
+ 
++#ifdef CONFIG_LEDS_GPIO
++static struct gpio_led ar2315_leds[6];
++static struct gpio_led_platform_data ar2315_led_data = {
++	.leds = (void *)ar2315_leds,
++};
++
++static struct platform_device ar2315_gpio_leds = {
++	.name = "leds-gpio",
++	.id = -1,
++	.dev = {
++		.platform_data = (void *)&ar2315_led_data,
++	}
++};
++
++static void __init ar2315_init_gpio_leds(void)
++{
++	static char led_names[6][6];
++	int i, led = 0;
++
++	ar2315_led_data.num_leds = 0;
++	for (i = 1; i < 8; i++) {
++		if ((i == AR2315_RESET_GPIO) ||
++		    (i == ath25_board.config->reset_config_gpio))
++			continue;
++
++		if (i == ath25_board.config->sys_led_gpio)
++			strcpy(led_names[led], "wlan");
++		else
++			sprintf(led_names[led], "gpio%d", i);
++
++		ar2315_leds[led].name = led_names[led];
++		ar2315_leds[led].gpio = i;
++		ar2315_leds[led].active_low = 0;
++		led++;
++	}
++	ar2315_led_data.num_leds = led;
++	platform_device_register(&ar2315_gpio_leds);
++}
++#else
++static inline void ar2315_init_gpio_leds(void)
++{
++}
++#endif
++
+ void __init ar2315_init_devices(void)
+ {
+ 	/* Find board configuration */
+@@ -270,6 +315,8 @@ void __init ar2315_init_devices(void)
+ 	ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
+ 	platform_device_register(&ar2315_gpio);
+ 
++	ar2315_init_gpio_leds();
++
+ 	ar2315_wdt_res[1].start = irq_create_mapping(ar2315_misc_irq_domain,
+ 						     AR2315_MISC_IRQ_WATCHDOG);
+ 	ar2315_wdt_res[1].end = ar2315_wdt_res[1].start;
+--- a/arch/mips/ath25/ar5312.c
++++ b/arch/mips/ath25/ar5312.c
+@@ -23,6 +23,7 @@
+ #include <linux/mtd/physmap.h>
+ #include <linux/reboot.h>
+ #include <linux/gpio.h>
++#include <linux/leds.h>
+ #include <asm/bootinfo.h>
+ #include <asm/reboot.h>
+ #include <asm/time.h>
+@@ -231,6 +232,23 @@ static struct platform_device ar5312_gpi
+ 	.num_resources = ARRAY_SIZE(ar5312_gpio_res),
+ };
+ 
++#ifdef CONFIG_LEDS_GPIO
++static struct gpio_led ar5312_leds[] = {
++	{ .name = "wlan", .gpio = 0, .active_low = 1, },
++};
++
++static const struct gpio_led_platform_data ar5312_led_data = {
++	.num_leds = ARRAY_SIZE(ar5312_leds),
++	.leds = (void *)ar5312_leds,
++};
++
++static struct platform_device ar5312_gpio_leds = {
++	.name = "leds-gpio",
++	.id = -1,
++	.dev.platform_data = (void *)&ar5312_led_data,
++};
++#endif
++
+ static void __init ar5312_flash_init(void)
+ {
+ 	void __iomem *flashctl_base;
+@@ -301,6 +319,11 @@ void __init ar5312_init_devices(void)
+ 
+ 	platform_device_register(&ar5312_gpio);
+ 
++#ifdef CONFIG_LEDS_GPIO
++	ar5312_leds[0].gpio = config->sys_led_gpio;
++	platform_device_register(&ar5312_gpio_leds);
++#endif
++
+ 	/* Fix up MAC addresses if necessary */
+ 	if (is_broadcast_ether_addr(config->enet0_mac))
+ 		ether_addr_copy(config->enet0_mac, config->enet1_mac);
